Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ice Formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

An Investigation of the Icing and Heated-air De-icing Characteristics of the R-2600-13 Induction System

A laboratory investigation was made on a Holley 1685-HB carburetor mounted on an R-2600-13 supercharger assembly to determine the icing characteristics and the heated-air de-icing requirements of this portion of the B-25D airplane induction system. Icing has been found to be most prevalent at relatively small throttle openings and, consequently, all runs were made at simulated 60-percent normal rated power condition. Icing characteristics were determined during a series of 15-minute runs over a range of inlet-air conditions. For the de-icing investigation severe impact ice was allowed to form in the induction system and the time required for the recovery of 95 percent of the maximum possible air flow at the original throttle setting was then determined for a range of wet-bulb temperatures. Results of these runs showed that ice on the walls of the carburetor adapter and on the rim of the impeller-shroud portion of the supercharger diffuser plate did not affect engine operation at 60-percent normal rated power. Ice that adversely affected the air flow and the fuel-air ratio was formed only on the central web of the carburetor and then only when the inlet air was saturated or contained free moisture in excess of saturation. No serious ice formations were observed at inlet-air temperatures above 66 0 F or with an inlet-air enthalpy greater than 34 Btu per pound. The maximum temperature at. which any trace of icing could be detected was 1110 F with a relative humidity of approximately 28 percent, The air-flow recovery time for emergency de-icing was 0.3 minute for.an enthalpy of 35 Btu per pound or wet-bulb temperature of 68 0 F. Further increase in enthalpy and wet-bulb temperature above these values resulted in very slight improvement in recovery time. The fuel-air ratio restored by a 5-Minute application of heated air was approximately 7 percent less than the initial value for cold-air conditions.

Chapman, Gilbert E.↗
NASA NTRS2016

Effect of Molecular Flexibility upon Ice Adhesion Shear Strength

Ice formation on aircraft surfaces effects aircraft performance by increasing weight and drag leading to loss of lift. Current active alleviation strategies involve pneumatic boots, heated surfaces, and usage of glycol based de-icing fluids. Mitigation or reduction of in-flight icing by means of a passive approach may enable retention of aircraft capabilities, i.e., no reduction in lift, while reducing the aircraft weight and mechanical complexity. Under a NASA Aeronautics Research Institute Seedling activity, the effect of end group functionality and chain length upon ice adhesion shear strength (IASS) was evaluated with the results indicating that chemical functionality and chain length (i.e. molecular flexibility) affected IASS. Based on experimental and modeling results, diamine monomers incorporating molecular flexibility as either a side chain or in between diamine functionalities were prepared, incorporated into epoxy resins that were subsequently used to fabricate coatings on aluminum substrates, and tested in a simulated icing environment. The IASS was found to be lower when molecular flexibility was incorporated in the polymer chain as opposed to a side chain.

Smith, Joseph G.↗
NASA NTRS2002

The Development and Application of a Method to Quantify the Quality of Cryoprotectant Conditions Using Standard Area Detector X-Ray Images

An X-ray based method for determining cryoprotectant concentrations necessary to protect solutions from crystalline ice formation was developed. X-ray images from a CCD area detector were integrated as powder patterns and quantified by determining the standard deviation of the slope of the normalized intensity curve in the resolution range where ice rings are known to occur. The method was tested determining the concentrations of glycerol, PEG400, ethylene glycol and 1,2-propanediol necessary to form an amorphous glass at 1OOK with each of the 98 crystallization solutions of Crystal Screens I and II (Hampton Research, Laguna Hills, California, USA). For conditions that required glycerol concentrations of 35% or above cryoprotectant conditions using 2,3-butanediol were determined. The method proved to be remarkably accurate. The results build on the work of [Garman and Mitchell] and extend the number, of suitable starting conditions to alternative cryoprotectants. In particular, 1,2-propanediol has emerged as a particularly good additive for glass formation upon flash cooling.

McFerrin, Michael↗
NASA NTRS1940

Aerodynamic heating and the deflection of drops by an obstacle in an air stream in relation to aircraft icing

Two topics of interest to persons attempting to apply the heat method of preventing ice formation on aircraft are considered. Surfaces moving through air at high speed are shown, both theoretically and experimentally, to be subject to important aerodynamic heating effects that will materially reduce the heat required to prevent ice. Numerical calculations of the path of water drops in an air stream around a circular cylinder are given. From these calculations, information is obtained on the percentage of the swept area cleared of drops.

Kantrowitz, Arthur↗
NASA NTRS1971

Remote Sensing of Sea Ice from Earth Satellites

The application of meteorological satellite data for mapping ice fields is discussed. The characteristics of the photographic records of sea ice formations are described. The derivation of the composite minimum brightness chart by computer processing of the mapped satellite vidicon data for several successive days is explained. The factors which create a quantitative delimiting of the sea ice conditions are explained.

Mcclain, E. P.↗
NASA NTRS1985

Determination of sea ice motion using digital SAR imagery

Precise, densely sampled maps of ice motion have been derived from digital Seasat SAR imagery, in order to determine the small scale spatial variability of ice formation. The SAR images were processed to remove geometric distortions, and then located to an accuracy of about 100 m by means of a spacecraft orbital data/SAR characteristics algorithm, independently of attitude and ground reference point data. Ice features common to an overlapping pair of images yielded vector plots of ice motion that indicate a high degree of spatial deformation, demonstrating the potential value of spaceborne SAR data.

Curlander, J. C.↗
NASA NTRS2021

Preconditioning of overcast-to-broken cloud transitions by riming in marine cold air outbreaks

Marine cold air outbreaks (CAOs) commonly form overcast cloud decks that transition into broken cloud fields downwind, dramatically altering the local radiation budget. In this study, we investigate the impact of frozen hydrometeors on these transitions. We focus on a CAO case in the NW Atlantic, the location of the multi-year flight campaign ACTIVATE (Aerosol Cloud meTeorology Interactions oVer the western ATlantic Experiment). We use MERRA-2 (Modern-Era Retrospective analysis for Research and Applications, version 2) reanalysis fields to drive large eddy simulations with mixed-phase two-moment microphysics in a Lagrangian framework. We find that transitions are triggered by substantial rain (rainwater paths >25 g m−2), and only simulations that allow for aerosol depletion result in sustained breakups, as observed. Using a range of diagnostic ice nucleating particle concentrations, Ninp, we find that increasing ice progressively accelerates transitions, thus abbreviating the overcast state. Ice particles affect the cloud-topped boundary layer evolution, primarily through riming-related processes prior to substantial rain, leading to (1) a reduction in cloud liquid water, (2) early consumption of cloud condensation nuclei, and (3) early and light precipitation cooling and moistening below cloud. We refer to these three effects collectively as “preconditioning by riming”. Greater boundary layer aerosol concentrations available as cloud condensation nuclei (CCN) delay the onset of substantial rain. However, cloud breakup and low CCN concentration final stages are found to be inevitable in this case, due, primarily, to liquid water path buildup. An ice-modulated cloud transition speed suggests the possibility of a negative cloud–climate feedback. To address prevailing uncertainties in the model representation of mixed-phase processes, the magnitude of ice formation and riming impacts and, thereby, the strength of an associated negative cloud–climate feedback process, requires further observational evaluation by targeting riming hot spots with in situ imaging probes that allow for both the characterization of ice particles and abundance of supercooled droplets.

Marine cold air outbreaks↗
NASA NTRS1993

Low-power millimeter-wave radar observations of the atmosphere

Historically, cloud structures, dynamics, and precipitation processes have been observed and measured with sensors from two different spatial resolutions. Laser-based sensors have volume resolutions on the order of 10(exp -4) to 10(exp -2) cubic meters for a 1-s sample. Radar systems operating at wavelengths between 1 and 10 cm have resolutions on the order of 10(exp 4) to 10(exp 7) cubic meters. The resolutions of micro-wave systems depend primarily on the system RF bandwidth and antenna bandwidth. Both resolution regimes were useful in the study of cloud structures and processes - the former for determining resolution on the individual cloud particle scale and the latter for studying the coarse characteristics of cloud dynamics and structure. There are, however, cloud processes and structures that occur on scales that lie between these two regimes: the process of entrainment, where outside air is brought within the cloud boundaries; the mixing of in-cloud particles with different histories; cloud particle coalescence; and ice formation. The use of mm-wave (30- to 300-GHz) radars offers an opportunity to observe cloud processes at these scales and determine their influence on precipitation development, cloud albedos, cloud lifetimes, chemical cycling of tract substances, aircraft icing, and other meteorological phenomena. To determine the usefulness of a 35-GHz radar for observing these precipitation and cloud processes, a research program was initiated. The objectives of this program are to develop a 35-GHz radar, to measure scattering from precipitation and clouds, and to develop a model to compute scattering from clouds using the finite-difference time-domain (FDTD) technique.

Ronnau, James F.↗
NASA NTRS1997

ERS Satellite Microwave Radar Observations of Antarctic Sea-Ice Dynamics

ERS-1 and ERS-2 scatterometer and SAR data are used to monitor and track large and small-scale sea-ice dynamics in the Southern Ocean, and in particular in the Weddell Sea, Antarctica. Sea-ice formation in the Weddell Sea regulates vertical and horizontal thermohaline circulation and influences bottom water production rates.

Antarctic↗
NASA NTRS1993

Fourier transform-infrared studies of thin H2SO4/H2O films: Formation, water uptake, and solid-liquid phase changes

Fourier transform-infrared (FTIR) spectroscopy was used to examine films representative of stratospheric sulfuric acid aerosols. Thin films of sulfuric acid were formed in situ by the condensed phase reaction of SO3 with H2O. FTIR spectra show that the sulfuric acid films absorb water while cooling in the presence of water vapor. Using stratospheric water pressures, the most dilute solutions observed were greater than 40 wt % before simultaneous ice formation and sulfuric acid freezing occurred. FTIR spectra also revealed that the sulfuric acid films crystallized mainly as sulfuric acid tetrahydrate (SAT). Crystallization occurred either when the composition was about 60 wt% H2SO4 or after ice formed on the films at temperatures 1-4 K below the ice frost point. Finally, we determined that the melting point for SAT depended on the background water pressure and was 216-219 K in the presence of 4 x 10(exp -4) Torr H2O. Our results suggest that once frozen, sulfuric acid aerosols in the stratosphere are likely to melt at these temperatures, 30 K colder than previously thought.

Middlebrook, Ann M.↗
NASA NTRS2011

Variability and Trends in Sea Ice Extent and Ice Production in the Ross Sea

Salt release during sea ice formation in the Ross Sea coastal regions is regarded as a primary forcing for the regional generation of Antarctic Bottom Water. Passive microwave data from November 1978 through 2008 are used to examine the detailed seasonal and interannual characteristics of the sea ice cover of the Ross Sea and the adjacent Bellingshausen and Amundsen seas. For this period the sea ice extent in the Ross Sea shows the greatest increase of all the Antarctic seas. Variability in the ice cover in these regions is linked to changes in the Southern Annular Mode and secondarily to the Antarctic Circumpolar Wave. Over the Ross Sea shelf, analysis of sea ice drift data from 1992 to 2008 yields a positive rate of increase in the net ice export of about 30,000 sq km/yr. For a characteristic ice thickness of 0.6 m, this yields a volume transport of about 20 cu km/yr, which is almost identical, within error bars, to our estimate of the trend in ice production. The increase in brine rejection in the Ross Shelf Polynya associated with the estimated increase with the ice production, however, is not consistent with the reported Ross Sea salinity decrease. The locally generated sea ice enhancement of Ross Sea salinity may be offset by an increase of relatively low salinity of the water advected into the region from the Amundsen Sea, a consequence of increased precipitation and regional glacial ice melt.

Comiso, Josefino↗
NASA NTRS2000

Freezing Rain as an In-Flight Icing Hazard

Exposure to supercooled large drops (SLD-subfreezing water droplets with diameters greater than approx. 50 microns) can pose a significant threat to the safety of some aircraft. Although SLD includes both freezing drizzle (FZDZ) and freezing rain (FZRA), much of the SLD research and development of operational SLD forecast tools has focused on FZDZ and ignored FZRA, regarding is as less of a hazard to aviation. This paper provides a counterpoint case study that demonstrates FZRA as a significant in-flight icing hazard. The case study is based on flight and meteorological data from a joint NASA/FAA/NCAR SLD icing research project collected on February 4, 1998. The NASA Twin Otter Icing Research Aircraft experienced a prolonged exposure to "classical" FZRA that formed extensive ice formations including ridges and nodules on the wing and tail, and resulted in a substantial performance penalty. Although the case study provides only a singular FZRA event with one aircraft type, it is clear that classical FZRA can pose a significant in-flight icing hazard, and should not be ignored when considering SLD issues.

Bernstein, Ben C.↗
NASA NTRS1999

Navier-Stokes Analysis of the Flowfield Characteristics of an Ice Contaminated Aircraft Wing

An analytical study was performed as part of the NASA Lewis support of a National Transportation Safety Board (NTSB) aircraft accident investigation. The study was focused on the performance degradation associated with ice contamination on the wing of a commercial turbo-prop-powered aircraft. Based upon the results of an earlier numerical study conducted by the authors, a prominent ridged-ice formation on the subject aircraft wing was selected for detailed flow analysis using 2-dimensional (2-D), as well as, 3-dimensional (3-D) Navier-Stokes computations. This configuration was selected because it caused the largest lift decrease and drag increase among all the ice shapes investigated in the earlier study. A grid sensitivity test was performed to find out the influence of grid spacing on the lift, drag, and associated angle-of-attack for the maximum lift (C(sub lmax)). This study showed that grid resolution is important and a sensitivity analysis is an essential element of the process in order to assure that the final solution is independent of the grid. The 2-D results suggested that a severe stability and control difficulty could have occurred at a slightly higher angle-of-attack (AOA) than the one recorded by the Flight Data Recorder (FDR). This stability and control problem was thought to have resulted from a decreased differential lift on the wings with respect to the normal loading for the configuration. The analysis also indicated that this stability and control problem could have occurred whether or not natural ice shedding took place. Numerical results using an assumed 3-D ice shape showed an increase of the angle at which this phenomena occurred of about 4 degrees. As it occurred with the 2-D case, the trailing edge separation was observed but started only when the AOA was very close to the angle at which the maximum lift occurred.

Chung, J.↗
DOE OSTI2026

Thermo-hydro-mechanical analysis of subsurface ice-based thermal energy storage

Ice-based thermal energy storage systems are widely utilized for cooling and managing peak electrical demand globally, offering daily or weekly storage capabilities for both individual homes and larger office buildings. However, scaling these systems for district-level cooling or integrating them with renewable energy sources presents challenges, especially in accommodating larger volumes and addressing seasonal storage requirements in densely populated urban areas. This paper proposes a novel solution by evaluating subsurface ice-based thermal energy storage, in which the underground is subjected to seasonal freeze/thaw cycles. However, these cycles may influence ground behavior, affecting pore pressure and inducing ground movement. To systematically investigate these challenges, we enhance the TOUGH-FLAC simulator by integrating water/ice phase change capabilities and updating the effective stress–strain constitutive relation. Both modifications are validated against analytical solutions or experimental data. Through numerical simulations spanning a decade with ten seasonal freeze/thaw cycles, we evaluate the performance and long-term stability of a generic subsurface ice-based thermal energy storage system, considering factors such as ground permeability, freezing pipe spacing, freeze/thaw damage, and glycol solution temperature. The simulations indicate that ice formation induces pore pressure variations that drive seasonal surface heave and settlement, controlled by ground permeability, pipe spacing, and glycol solution temperature, along with tensile and localized shear deformation around freeze pipes. This highlights the need for accurate ground property characterization and geomechanical analysis for subsurface ice-based thermal energy storage.

Ground freezing↗
NASA NTRS2005

Monitoring Floods with NASA's ST6 Autonomous Sciencecraft Experiment: Implications on Planetary Exploration

NASA's New Millennium Program (NMP) Autonomous Sciencecraft Experiment (ASE) [1-3] has been successfully demonstrated in Earth-orbit. NASA has identified the development of an autonomously operating spacecraft as a necessity for an expanded program of missions exploring the Solar System. The versatile ASE spacecraft command and control, image formation, and science processing software was uploaded to the Earth Observer 1 (EO-1) spacecraft in early 2004 and has been undergoing onboard testing since May 2004 for the near real-time detection of surface modification related to transient geological and hydrological processes such as volcanism [4], ice formation and retreat [5], and flooding [6]. Space autonomy technology developed as part of ASE creates the new capability to autonomously detect, assess, react to, and monitor dynamic events such as flooding. Part of the challenge has been the difficulty to observe flooding in real time at sufficient temporal resolutions; more importantly, it is the large spatial extent of most drainage networks coupled with the size of the data sets necessary to be downlinked from satellites that make it difficult to monitor flooding from space. Below is a description of the algorithms (referred to as ASE Flood water Classifiers) used in tandem with the Hyperion spectrometer instrument on EO-1 to identify flooding and some of the test results.

Ip, Felipe↗
NASA NTRS1992

Simulations of the seasonal polar caps on Mars

One of the most puzzling mysteries about the planet Mars is the hemispherical asymmetry in the polar caps. Every spring the seasonal polar cap of CO2 recedes until the end of summer, when only a small part, the residual polar cap, remains. During the year that Viking observed Mars, the residual polar cap was composed of water ice in the Northern Hemisphere (Kieffer et al., Science, 194, 1341, 1976), but was primarily carbon dioxide ice in the Southern Hemisphere (Kieffer, J. Geophys. Res., 84, 8263, 1979). Scientists have sought to explain this asymmetry by modeling observations of the latitudinal recession of the polar cap and seasonal variations in atmospheric pressure (since the seasonal polar caps are primarily frozen atmosphere, they are directly related to changes in atmospheric mass). These models reproduce most aspects of the observed annual variation in atmospheric pressure fairly accurately. Furthermore, the predicted latitudinal recession of the northern polar cap in the spring agrees well with observations, including the fact that CO2 ice is predicted to completely sublime away. However, these models all predict that the carbon dioxide ice will also sublime away during the summer in the Southern Hemisphere, unlike what is observed. It is shown here how the radiative effects of ozone, clouds, and airborne dust, light penetration into and through the polar cap, and the dependence of albedo on solar zenith angle affect CO2 ice formation and sublimation, and how they help explain the hemispherical asymmetry in the residual polar caps. These effects have not been studied with prior polar cap models. The combination of the effects of solar zenith angle on albedo and the radiative effects of clouds and dust act to extend the lifetime of CO2 ice on the south pole relatively more than on the north pole, possibly explaining the hemispherical asymmetry in the residual polar caps without the need of a hemispherical asymmetry in polar cap albedo. This does not imply that a hemispherical asymmetry in polar cap albedo does not exist, but that one is not necessary. Observations of the regression of the polar caps and the annual cycle in atmospheric pressure are reproduced fairly well by the model, as shown in the figures, although further improvement is needed. When CO2 ice is retained at the south pole, the model predictions of the annual cycle in atmospheric pressure have a phase shift relative to the data, no matter what model input parameters are used. We are investigating other processes not included in prior polar cap models.

Lindner, Bernhard Lee↗
NASA NTRS2013

A Non-Cut Cell Immersed Boundary Method for Use in Icing Simulations

This paper describes a computational fluid dynamic method used for modelling changes in aircraft geometry due to icing. While an aircraft undergoes icing, the accumulated ice results in a geometric alteration of the aerodynamic surfaces. In computational simulations for icing, it is necessary that the corresponding geometric change is taken into consideration. The method used, herein, for the representation of the geometric change due to icing is a non-cut cell Immersed Boundary Method (IBM). Computational cells that are in a body fitted grid of a clean aerodynamic geometry that are inside a predicted ice formation are identified. An IBM is then used to change these cells from being active computational cells to having properties of viscous solid bodies. This method has been implemented in the NASA developed node centered, finite volume computational fluid dynamics code, FUN3D. The presented capability is tested for two-dimensional airfoils including a clean airfoil, an iced airfoil, and an airfoil in harmonic pitching motion about its quarter chord. For these simulations velocity contours, pressure distributions, coefficients of lift, coefficients of drag, and coefficients of pitching moment about the airfoil's quarter chord are computed and used for comparison against experimental results, a higher order panel method code with viscous effects, XFOIL, and the results from FUN3D's original solution process. The results of the IBM simulations show that the accuracy of the IBM compares satisfactorily with the experimental results, XFOIL results, and the results from FUN3D's original solution process.

Sarofeen, Christian M.↗
DOE OSTI2020

AEROICESTUDY Colorado State University Continuous Flow Diffusion Chamber (CFDC) version R0

This dataset comprises measurements of atmospheric ice nucleating particle (INP) number concentrations at ARM's Southern Great Plains (SGP) Site Guest Instrument Facility (GIF), in Lamont, Oklahoma, during the 2019 Aerosol-Ice Formation Closure Pilot Study (AEROICESTUDY). The results reported here are from the Colorado State University Continuous Flow Diffusion Chamber (CFDC-1H) and represent real-time measurements of ambient INPs.

54 ENVIRONMENTAL SCIENCES↗