Results for “Icing conditions” — Page 12

NASA NTRS2011

Wheel-Based Ice Sensors for Road Vehicles

Wheel-based sensors for detection of ice on roads and approximate measurement of the thickness of the ice are under development. These sensors could be used to alert drivers to hazardous local icing conditions in real time. In addition, local ice-thickness measurements by these sensors could serve as guidance for the minimum amount of sand and salt required to be dispensed locally onto road surfaces to ensure safety, thereby helping road crews to utilize their total supplies of sand and salt more efficiently. Like some aircraft wing-surface ice sensors described in a number of previous NASA Tech Briefs articles, the wheelbased ice sensors are based, variously, on measurements of changes in capacitance and/or in radio-frequency impedance as affected by ice on surfaces. In the case of ice on road surfaces, the measurable changes in capacitance and/or impedance are attributable to differences among the electric permittivities of air, ice, water, concrete, and soil. In addition, a related phenomenon that can be useful for distinguishing between ice and water is a specific transition in the permittivity of ice at a temperature- dependent frequency. This feature also provides a continuous calibration of the sensor to allow for changing road conditions. Several configurations of wheel-based ice sensors are under consideration. For example, in a simple two-electrode capacitor configuration, one of the electrodes would be a circumferential electrode within a tire, and the ground would be used as the second electrode. Optionally, the steel belts that are already standard parts of many tires could be used as the circumferential electrodes. In another example (see figure), multiple electrodes would be embedded in rubber between the steel belt and the outer tire surface. These electrodes would be excited in alternating polarities at one or more suitable audio or radio frequencies to provide nearly continuous monitoring of the road surface under the tire. In still another example, one or more microwave stripline(s) or coplanar waveguide(s) would be embedded in a tire near its outer surface; in comparison with lower-frequency capacitive devices, a device of this type could be more sensitive.

Arndt, G. Dickey↗

NASA NTRS1948

Icing and De-Icing of a Propeller with Internal Electric Blade Heaters

An investigation has been made in the NACA Cleveland icing research tunnel to determine the de-icing effectiveness of an experimental configuration of an Internal electric propeller-blade heater. Two atmospheric Icing conditions and two propeller operating conditions were Investigated, In experiments with unheated blades and with heat applied to the blades both continuously and cyclically. Data are presented to show the effect of propeller speed., ambient air temperature and liquid-water concentration, and the duration of the heat-on and cycle times on the power requirements and de-Icing performance of the blade heaters. The extent of ice-covered area on the blades for various icing ax4 operating conditions has been determined. The largest iced area was obtained at the higher ambient-air temperatures and at low propeller speed. The ohord.wise extent of Icing In practically every case was greater than that covered by blade heaters. Adequate de-icing in the heated area with continuous application of heat was obtained with the power available but a maximum power, input of 1250 watts per blade was insufficient for cyclic de-Icing for the range of conditions investigated. Blade-surface temperature rates of rise of 0.2 to 0.7 F per second were obtained and the minimum cooling period for cyclic de-icing was found to be approximately 2-1/2 times the heating period.

Lewis, James P.↗

NASA NTRS1978

The sensitivity of the general circulation to Arctic Sea ice boundaries - A numerical experiment

Results are presented for a set of numerical experiments conducted with the Goddard (formerly GISS) general circulation model. The experiments were designed to test the model atmospheric response to a single fixed and specified parameter, the total ice cover in the Davis Strait, Barents Sea, East Greenland Sea, Sea of Okhotsk and Bering Sea. Margin variations are considered that are substantially smaller than those involved in ice age or ice-free Arctic simulations. Anomaly is defined as the mean of two runs corresponding to climatological maximum sea ice conditions. Model results indicate that the ice margin anomalies are capable of altering local climates in certain regions of high and middle latitudes. Possible interactions between high latitudes and subtropical regions are suggested.

Herman, G. F.↗

NASA NTRS1985

Icing flight research: Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes was obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft darg coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (C sub d) of 0.5.

Mikkelsen, K. L.↗

NASA NTRS1985

Icing flight research - Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes were obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft drag coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (c sub d) of 0.5.

Mikkelsen, K. L.↗

NASA NTRS1988

Use of SAR imagery and other remotely-sensed data in deriving ice information during a severe ice event on the Grand Banks (Newfoundland)

Image data from synthetic aperture radar (SAR) are used to observe an ice compaction event off the East Coast of Newfoundland in spring, 1987. The information developed from sequential SAR observations is shown to do a remarkably effective job of describing the ice conditions; the difficult variable is the ice thickness which is found to be surprisingly large (2 to 4 times the thickness predictable from thermodynamic growth alone). It may be possible to model the ice thickness using SAR-derived ice motion.

Carsey, F. D.↗

NASA NTRS1989

Comparison of sea ice parameters retrieved from passive microwave (SSM/I), Landsat MSS and AVHRR imagery

Ice concentrations derived from passive microwave data from the Special Sensing Microwave Imager (SSM/I), the Landsat MSS, and the AVHRR are compared for the validation of SSM/I-derived sea-ice products. Case studies with data from the Beaufort, Bering, East Greenland, and Weddell Seas are conducted to evaluate the performance of the NASA Team SSM/I algorithm under various sea-ice conditions. The results show that SSM/I ice concentrations are accurate with a mean error of 15 percent using globally derived tie points.

Schweiger, Axel J.↗

NASA NTRS2007

Observations on the Growth of Roughness Elements Into Icing Feathers

This work presents the results of an experiment conducted in the Icing Research Tunnel at NASA Glenn Research Center to understand the process by which icing feathers are formed in the initial stages of ice accretion formation on swept wings. Close-up photographic data were taken on an aluminum NACA 0012 swept wing tip airfoil. Two types of photographic data were obtained: time sequence close-up photographic data during the run and close-up photographic data of the ice accretion at the end of each run. Icing runs were conducted for short ice accretion times from 10 to 180 sec. The time sequence close-up photographic data was used to study the process frame by frame and to create movies of how the process developed. The movies confirmed that at glaze icing conditions in the attachment line area icing feathers develop from roughness elements. The close-up photographic data at the end of each run showed that roughness elements change into a pointed shape with an upstream facet and join on the side with other elements having the same change to form ridges with pointed shape and upstream facet. The ridges develop into feathers when the upstream facet grows away to form the stem of the feather. The ridges and their growth into feathers were observed to form the initial scallop tips present in complete scallops.

Vargas, Mario↗

NASA NTRS2014

Icing Analysis of a Swept NACA 0012 Wing Using LEWICE3D Version 3.48

Icing calculations were performed for a NACA 0012 swept wing tip using LEWICE3D Version 3.48 coupled with the ANSYS CFX flow solver. The calculated ice shapes were compared to experimental data generated in the NASA Glenn Icing Research Tunnel (IRT). The IRT tests were designed to test the performance of the LEWICE3D ice void density model which was developed to improve the prediction of swept wing ice shapes. Icing tests were performed for a range of temperatures at two different droplet inertia parameters and two different sweep angles. The predicted mass agreed well with the experiment with an average difference of 12%. The LEWICE3D ice void density model under-predicted void density by an average of 30% for the large inertia parameter cases and by 63% for the small inertia parameter cases. This under-prediction in void density resulted in an over-prediction of ice area by an average of 115%. The LEWICE3D ice void density model produced a larger average area difference with experiment than the standard LEWICE density model, which doesn't account for the voids in the swept wing ice shape, (115% and 75% respectively) but it produced ice shapes which were deemed more appropriate because they were conservative (larger than experiment). Major contributors to the overly conservative ice shape predictions were deficiencies in the leading edge heat transfer and the sensitivity of the void ice density model to the particle inertia parameter. The scallop features present on the ice shapes were thought to generate interstitial flow and horse shoe vortices which enhance the leading edge heat transfer. A set of changes to improve the leading edge heat transfer and the void density model were tested. The changes improved the ice shape predictions considerably. More work needs to be done to evaluate the performance of these modifications for a wider range of geometries and icing conditions

Ice Accretion Software↗

NASA NTRS2014

Icing Analysis of a Swept NACA 0012 Wing Using LEWICE3D Version 3.48

Icing calculations were performed for a NACA 0012 swept wing tip using LEWICE3D Version 3.48 coupled with the ANSYS CFX flow solver. The calculated ice shapes were compared to experimental data generated in the NASA Glenn Icing Research Tunnel (IRT). The IRT tests were designed to test the performance of the LEWICE3D ice void density model which was developed to improve the prediction of swept wing ice shapes. Icing tests were performed for a range of temperatures at two different droplet inertia parameters and two different sweep angles. The predicted mass agreed well with the experiment with an average difference of 12%. The LEWICE3D ice void density model under-predicted void density by an average of 30% for the large inertia parameter cases and by 63% for the small inertia parameter cases. This under-prediction in void density resulted in an over-prediction of ice area by an average of 115%. The LEWICE3D ice void density model produced a larger average area difference with experiment than the standard LEWICE density model, which doesn't account for the voids in the swept wing ice shape, (115% and 75% respectively) but it produced ice shapes which were deemed more appropriate because they were conservative (larger than experiment). Major contributors to the overly conservative ice shape predictions were deficiencies in the leading edge heat transfer and the sensitivity of the void ice density model to the particle inertia parameter. The scallop features present on the ice shapes were thought to generate interstitial flow and horse shoe vortices which enhance the leading edge heat transfer. A set of changes to improve the leading edge heat transfer and the void density model were tested. The changes improved the ice shape predictions considerably. More work needs to be done to evaluate the performance of these modifications for a wider range of geometries and icing conditions.

Icing CFD↗

NASA NTRS2016

Ice-Accretion Test Results for Three Large-Scale Swept-Wing Models in the NASA Icing Research Tunnel

Icing simulation tools and computational fluid dynamics codes are reaching levels of maturity such that they are being proposed by manufacturers for use in certification of aircraft for flight in icing conditions with increasingly less reliance on natural-icing flight testing and icing-wind-tunnel testing. Sufficient high-quality data to evaluate the performance of these tools is not currently available. The objective of this work was to generate a database of ice-accretion geometry that can be used for development and validation of icing simulation tools as well as for aerodynamic testing. Three large-scale swept wing models were built and tested at the NASA Glenn Icing Research Tunnel (IRT). The models represented the Inboard (20 percent semispan), Midspan (64 percent semispan) and Outboard stations (83 percent semispan) of a wing based upon a 65 percent scale version of the Common Research Model (CRM). The IRT models utilized a hybrid design that maintained the full-scale leading-edge geometry with a truncated afterbody and flap. The models were instrumented with surface pressure taps in order to acquire sufficient aerodynamic data to verify the hybrid model design capability to simulate the full-scale wing section. A series of ice-accretion tests were conducted over a range of total temperatures from -23.8 to -1.4 C with all other conditions held constant. The results showed the changing ice-accretion morphology from rime ice at the colder temperatures to highly 3-D scallop ice in the range of -11.2 to -6.3 C. Warmer temperatures generated highly 3-D ice accretion with glaze ice characteristics. The results indicated that the general scallop ice morphology was similar for all three models. Icing results were documented for limited parametric variations in angle of attack, drop size and cloud liquid-water content (LWC). The effect of velocity on ice accretion was documented for the Midspan and Outboard models for a limited number of test cases. The data suggest that there are morphological characteristics of glaze and scallop ice accretion on these swept-wing models that are dependent upon the velocity. This work has resulted in a large database of ice-accretion geometry on large-scale, swept-wing models.

Wing Aerodynamics↗

NASA NTRS2016

Ice-Accretion Test Results for Three Large-Scale Swept-Wing Models in the NASA Icing Research Tunnel

Icing simulation tools and computational fluid dynamics codes are reaching levels of maturity such that they are being proposed by manufacturers for use in certification of aircraft for flight in icing conditions with increasingly less reliance on natural-icing flight testing and icing-wind-tunnel testing. Sufficient high-quality data to evaluate the performance of these tools is not currently available. The objective of this work was to generate a database of ice-accretion geometry that can be used for development and validation of icing simulation tools as well as for aerodynamic testing. Three large-scale swept wing models were built and tested at the NASA Glenn Icing Research Tunnel (IRT). The models represented the Inboard (20% semispan), Midspan (64% semispan) and Outboard stations (83% semispan) of a wing based upon a 65% scale version of the Common Research Model (CRM). The IRT models utilized a hybrid design that maintained the full-scale leading-edge geometry with a truncated afterbody and flap. The models were instrumented with surface pressure taps in order to acquire sufficient aerodynamic data to verify the hybrid model design capability to simulate the full-scale wing section. A series of ice-accretion tests were conducted over a range of total temperatures from -23.8 deg C to -1.4 deg C with all other conditions held constant. The results showed the changing ice-accretion morphology from rime ice at the colder temperatures to highly 3-D scallop ice in the range of -11.2 deg C to -6.3 deg C. Warmer temperatures generated highly 3-D ice accretion with glaze ice characteristics. The results indicated that the general scallop ice morphology was similar for all three models. Icing results were documented for limited parametric variations in angle of attack, drop size and cloud liquid-water content (LWC). The effect of velocity on ice accretion was documented for the Midspan and Outboard models for a limited number of test cases. The data suggest that there are morphological characteristics of glaze and scallop ice accretion on these swept-wing models that are dependent upon the velocity. This work has resulted in a large database of ice-accretion geometry on large-scale, swept-wing models.

Wind-Tunnel Tests↗

NASA NTRS2004

2D Analysis of In-flight Light Particles

One of the primary uses of the in-flight icing research performed aboard NASA Glenn s DHC-6 Twin Otter is for Icing Research Tunnel (IRT) and icing prediction code (Lewice) validation. Using the in-flight data to establish the IRT and Lewice as accurate simulators of actual icing conditions is crucial for supporting the research done in the Icing Branch. During test flights during the 2003 and 2004 flight season, a Natural Ice Shape Database was collected. For flights where conditions were appropriate, the aircraft is flown in an icing cloud with all ice protection systems deactivated. The duration of this period is usually determined by the pilot s ability to safely control the aircraft. When safe flight is no longer possible, the aircraft is maneuvered into clear air above the cloud layer. At this point several photographs are taken of the ice shape that was accreted on the wing test section during this icing encounter using a stereo photograph system (Figure 1). The stereo photograph system utilizes two cameras located at different locations on the fuselage that are both pointed at the same location on the wing. When both cameras take photographs of the same location at the same time, the negatives can be combined digitally to generate a two dimensional plot describing the cross-section of the ice shape. After these photographs are taken, the wing de-icing boots are activated and the ice shape is removed.

Shearer, Jonathan↗

NASA NTRSDate not supplied

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models.

Icing↗

NASA NTRSDate not supplied

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models

Icing , Simulation, Validation↗

NASA NTRSDate not supplied

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models.

Icing↗

NASA NTRS1983

Shear zone ice deformation using supervised analysis of Seasat data

Spacecraft and aircraft Synthetic-Aperture Radar (SAR) images are commonly used to compute sea ice conditions including especially the drift velocities of ice features. Recent developments, described in this paper, in computer-aided analysis and in digital image processing have extended the analysis speed and accuracy of registration to the point that ice deformation can be examined on the geophysically important scales of about 100 m over tens of kilometers between two 'snapshots.' Examples are shown for the ice motion and rotation in the shear zone near the Alaska coast from Seasat data in 1978.

Carsey, F.↗

NASA NTRS1992

Analysis of surface roughness generation in aircraft ice accretion

Patterns of roughness evolution have been studied analysis of high magnification video observations of accreting ice surfaces provided by the NASA Lewis Research Center. Three distinct patterns of surface roughness generation have been identified within the parametric regions studied. They include: Rime, Multi-Zone Glaze, and Uniform Glaze. Under most icing conditions, a brief period of transient rime ice growth was observed caused by heat conduction into the body. The resulting thin rime layer explains previously observed insensitivity of some ice accretions to substrate insensitivity of some ice accretions to substrate surface chemistry and may provide justification for simplifying assumptions in ice accretion sailing and modeling effects.

Hansman, R. J., Jr.↗