SEARCH · Search NASA

Results for “Injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Effects of air injection on a turbocharged Teledyne Continential Motors TSIO-360-C engine

A turbocharged fuel injected aircraft engine was operated over a range of test conditions that included that EPA five-mode emissions cycle and fuel air ratio variations for individual modes while injecting air into the exhaust gas. Air injection resulted in a decrease of hydrocarbons and carbon monoxide while exceeding the maximum recommended turbine inlet temperature of 1650 F at the full rich mixture of the engine. Leanout tests indicated that the EPA standards could be met through the combined use of fuel management and air injection.

Cosgrove, D. V.↗

NASA NTRS1979

Injection of isotopic anomalies into the early solar nebula

The effectiveness of injecting material from outside the solar system into the early solar nebula was studied. Hydrodynamic calculations showed that the conditions of external injection of isotopically anomalous matter resemble a supernova remnant shell impacting an interstellar H I cloud. Since the injection process for grains or gas is determined before the impinging material penetrates a skin layer, the results for an H I edge should be valid for any configuration which joins the interstellar medium with an H I boundary zone. The effects of initial injection velocity, gas cooling, and magnetic fields are considered, and it is shown that grain penetration is limited to a layer with column density on the order of the grain mass/area ratio and that Rayleigh-Taylor instabilities are not expected to be effective at mixing the anomalous matter into the nebula during a cloud/shell interaction.

Margolis, S. H.↗

NASA NTRS1980

The effect of injection location on the spectrum of energetic magnetospheric particles

The role of local particle injections and accelerations in determining energetic particle spectra used as an indication of the radial diffusion of trapped magnetospheric particles is assessed. An idealized one-dimensional steady-state model of magnetospheric radial transport in which diffusion is balanced against particle sources and sinks is used to illustrate the effects of particle injection at a point and over a band of radii in which the observation point is immersed in particle spectra. For an injection spectrum uniformly distributed in space and a step function in energy, it is shown that the energy dependence of the measured spectrum is determined not only by adiabatic energization of the input spectrum but by the spatial structure of the injection and the radial dependence of the diffusion coefficient as well. The relevance of the results for observations of particle spectra in the terrestrial and Jovian magnetospheres is also considered

Birmingham, T. J.↗

NASA NTRS1980

Full-coverage film cooling. I - Comparison of heat transfer data for three injection angles

Wind tunnel experiments were carried out at Stanford between 1971 and 1977 to study the heat transfer characteristics of full-coverage film cooled surfaces with three geometries; normal-, 30 deg slant-, and 30 deg x 45 deg compound-angled injection. A flat full-coverage section and downstream recovery section comprised the heat transfer system. The experimental objectives were to determine, for each geometry, the effects on surface heat flux of injection blowing ratio, injection temperature ratio, and upstream initial conditions. Spanwise-averaged Stanton numbers were measured for blowing ratios from 0 to 1.3, and for two values of injection temperature at each blowing ratio. The heat transfer coefficient was defined on the basis of a mainstream-to-wall temperature difference. Initial momentum and enthalpy thickness Reynolds numbers were varied from 500 to about 3000.

Crawford, M. E.↗

NASA NTRS1982

Numerical investigation of supersonic base flow with parallel injection

The present investigation represents the first detailed numerical calculations of base flow with gas injection using a geometry and primary flow condition germane to a scramjet combustor. The investigation is concerned with the numerical solution of the complete two-dimensional Navier-Stokes equations for the flowfield in the vicinity of the base with parallel gas injection, taking into account the fluid dynamic aspects of this flowfield. The flow is dominated by separation, and by mixed regions of locally subsonic and supersonic flow. A comparison is conducted of flows with and without injection, and the effect of base injection on the wave patterns and shear layers of such flows is clearly established.

Sullins, G. A.↗

NASA NTRS1983

Injection molding ceramics to high green densities

The injection molding behavior of a concentrated suspension of Si powder in wax was studied. It was found that the injection molding behavior was a function of the processing techniques used to generate the powder. Dry ball-milled powders had the best molding behavior, while air classified and impact-milled powders demonstrated poorer injection moldability. The relative viscosity of these molding batches was studied as a function of powder properties: distribution shape, surface area, packing density, and particle morphology. The experimental behavior, in all cases, followed existing theories. The relative viscosity of an injection molding composition composed of dry ball-milled powders could be expressed using Farris' relation.

Mangels, J. A.↗

NASA NTRS1984

Injection-induced turbulence in stagnation-point boundary layers

A theory is developed for the stagnation point boundary layer with injection under the hypothesis that turbulence is produced at the wall by injection. From the existing experimental heat transfer rate data obtained in wind tunnels, the wall mixing length is deduced to be a product of a time constant and an injection velocity. The theory reproduces the observed increase in heat transfer rates at high injection rates. For graphite and carbon-carbon composite, the time constant is determined to be 0.0002 sec from the existing ablation data taken in an arc-jet tunnel and a balistic range.

Park, C.↗

NASA NTRS1985

Remote sensing of plasma injection and acceleration phenomena

Dynamics Explorer-1 High Altitude Plasma Instrument data have been used to investigate the injection of magnetosheath plasma into the polar cusp, the injection of auroral ion beams into the magnetosphere, and the acceleration of electrons transverse to the magnetic field direction, and the results are discussed. In the case of polar cusp plasmas, it is found that injection occurs at the high-latitude magnetopause, at geocentric distances near eight earth radii. In the case of auroral ion beams it is determined that ion bands are not produced by equatorial injection from the plasma sheet, but by the upward acceleration of ions from auroral acceleration regions. Finally, conical electron distributions are found to be consistent with transverse acceleration at altitudes of a thousand or more km, within or below the magnetic-field-aligned potential drops of the auroral acceleration regions.

Burch, J. L.↗

NASA NTRS1986

A laser-induced-fluorescence visualization study of transverse, sonic fuel injection in a nonreacting supersonic combustor

The present paper reports work which has been conducted in the first phase of a research program which is to provide a data base of spatially-resolved measurements in nonreacting supersonic combustors. In the measurements, a nonintrusive diagnostic technique based on the utilization of laser-induced fluorescence (LIF) is employed. The reported work had the objective to conduct LIF visualization studies of the injection of a simulated fuel into a Mach 2.07 airstream for comparison with corresponding numerical calculations. Attention is given to injection from a single orifice into a constant-area duct, injection from a single orifice behind a rearward-facing step, and injection from staged orifices behind a rearward-facing step.

Mcdaniel, J. C.↗

NASA NTRS1986

Argon ions injected parallel and perpendicular to the magnetic field

Preliminary results are reported of measurements obtained with the 0-10-kHz electric-field plasma-wave receivers and single-particle ion detectors of the ARCS-3 sounding-rocket payload over the auroral oval on February 10, 1985, after downward/field-parallel or transverse-spiral injection of Ar ions from the accelerator subpayload (separating itself at 2.3 m/s). The data are presented graphically and briefly characterized. The waves induced by the parallel injections are found to be much weaker than those induced by the perpendicular injections. In addition to the expected response to the Ar beam, an ion flux at pitch angle 90 deg was detected during the second parallel injection.

Erlandson, R. E.↗

NASA NTRS1987

Space charge effects during the injection of dense electron beams into space plasmas

One-dimensional electrostatic particle simulations are used to investigate the injection and propagation of intense electron beams and the plasma response to the beam injection. Beam densities greater than about the plasma density are considered. It is shown that if the injection is continuous, most of the beam electrons are drawn back into the spacecraft because of the buildup of positive charge on the spacecraft. Those electrons which are able to propagate away from the spacecraft are emitted periodically because of space charge oscillations induced by electric fields associated with the beam. A substantial increase in the fraction and average energy of electrons which can propagate away can be obtained if the injection is changed to periodic pulses having width and period matched to the induced space charge oscillations.

Winglee, R. M.↗

NASA NTRS1988

Liquid sprays and flow studies in the direct-injection diesel engine under motored conditions

A two dimensional, implicit finite difference method of the control volume variety, a two equation model of turbulence, and a discrete droplet model were used to study the flow field, turbulence levels, fuel penetration, vaporization, and mixing in diesel engine environments. The model was also used to study the effects of engine speed, injection angle, spray cone angle, droplet distribution, and intake swirl angle on the flow field, spray penetration and vaporization, and turbulence in motored two-stroke diesel engines. It is shown that there are optimum conditions for injection, which depend on droplet distribution, swirl, spray cone angle, and injection angle. The optimum conditions result in good spray penetration and vaporization and in good fuel mixing. The calculation presented clearly indicates that internal combustion engine models can be used to assess, at least qualitatively, the effects of injection characteristics and engine operating conditions on the flow field and on the spray penetration and vaporization in diesel engines.

Nguyen, Hung Lee↗

NASA NTRS1989

Electrostatic charging of spacecraft in response to electron beam injection

Electron beam injections from spacecraft now constitute a major activity in space research. Here, the charging level of a conducting surface when an electron beam is injected from it is investigated. Injections into both vacuum and an ambient plasma are considered. When a Maxwellian beam is injected into vacuum, the surface changes to a potential much greater than the average beam energy. The dependence of this excess is examined by considering beams with water-bag types of velocity distribution functions in which no electron has a velocity V(max) above a certain value. The electric field distribution in the electron sheath near the surface is determined by the pressure distribution. Thus, the surface potential is determined not only by V(max) but by all the beam parameters. The ambient plasma reduces the charging level and causes an oscillation in the surface potential. The oscillation frequency is the electron-plasma frequency associated with the ambient plasma.

Singh, Nagendra↗

NASA NTRS1992

Injection seeding of a Q-switched alexandrite laser: Study of frequency stabilization

AlGaAs diode lasers were used to injection seed a pulsed Q-switched alexandrite laser which produces a narrowband of radiation. Injection seeding is a method for achieving linewidths of less than 500 mega-Hz in the output of the broadband, tunable solid state laser. When the laser was set at a current of 59.8 milli-A and a temperature of 14.04 C, the wavelength was 767.6 nano-m. The Q-switched alexandrite laser was injection seeded and frequency stabilization was studied. The linewidth requirement was met, but the stability requirement was not due to drifting in the feedback voltage. Improvements on injection seeding should focus on increasing the feedback voltage to the laser diode, filtering the laser diode by using temperature controlled narrowband filters, and the use of diamond (SiC) grating placed inside the alexandrite laser's resonator cavity.

Brown, Lamarr A.↗

NASA NTRS1992

Advanced information processing system: Fault injection study and results

The objective of the AIPS program is to achieve a validated fault tolerant distributed computer system. The goals of the AIPS fault injection study were: (1) to present the fault injection study components addressing the AIPS validation objective; (2) to obtain feedback for fault removal from the design implementation; (3) to obtain statistical data regarding fault detection, isolation, and reconfiguration responses; and (4) to obtain data regarding the effects of faults on system performance. The parameters are described that must be varied to create a comprehensive set of fault injection tests, the subset of test cases selected, the test case measurements, and the test case execution. Both pin level hardware faults using a hardware fault injector and software injected memory mutations were used to test the system. An overview is provided of the hardware fault injector and the associated software used to carry out the experiments. Detailed specifications are given of fault and test results for the I/O Network and the AIPS Fault Tolerant Processor, respectively. The results are summarized and conclusions are given.

Burkhardt, Laura F.↗

NASA NTRS1991

Theoretical and experimental analysis of injection seeding a Q-switched alexandrite laser

Injection seeding is a method for achieving linewidths of less than 500 MHz in the output of broadband, tunable, solid state lasers. Dye lasers, CW and pulsed diode lasers, and other solid state lasers have been used as injection seeders. By optimizing the fundamental laser parameters of pump energy, Q-switched pulse build-up time, injection seed power and mode matching, one can achieve significant improvements in the spectral purity of the Q-switched output. These parameters are incorporated into a simple model for analyzing spectral purity and pulse build-up processes in a Q-switched, injection-seeded laser. Experiments to optimize the relevant parameters of an alexandrite laser show good agreement.

Prasad, C. R.↗

NASA NTRS1992

Effect of inert propellant injection on Mars ascent vehicle performance

A Mars ascent vehicle is limited in performance by the amount of propellant which can be brought from earth. In some cases the vehicle performance can be improved by injecting inert gas into the engine, if the inert gas is available as an in situ resource. CO2, N2 and Ar are constituents of the Martian atmosphere which are available at every point on the Martian surface and could be produced by a very simple processing technique, consisting essentially of compressing the atmosphere. The effect of inert gas injection on rocket engine performance was analyzed with a numerical code calculating chemical equilibrium in the engine, for engines of varying combustion chamber pressure, expansion ratio, oxidizer/fuel ratio, and inert injection fraction. Results of this analysis were applied to several candidate missions to determine how the required mass of return propellant needed in LEO could be decreased using inert propellant injection.

Colvin, James E.↗

NASA NTRS1992

Active control of asymmetric vortical flows around cones using injection and heating

The effectiveness of certain active-control methods for asymmetric flows around circular cones is investigated by using computational solution of the unsteady, compressible full Navier-Stokes equations. Two main methods of active control which include flow injection and surface heating are used. For the flow-injection-control method, flow injection is used either in the normal direction to the surface or in the tangential direction to the surface. For the surface-heating-control method, the temperature of the cone surface is increased. The effectiveness of a hybrid method of flow control which combines normal injection with surface heating has also been studied. The Navier-Stokes equations, subjected to various surface boundary conditions, are solved by using an implicit, upwind, flux-difference splitting, finite-volume scheme for locally-conical flow solutions.

Kandil, Osama A.↗