Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inverse scattering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The Development of Kinetic and Radiation Hydrodynamics Modeling of Thermonuclear Burn Propagation in Isochoric p - 11 B Through the Support of the INFUSE Program

The report summarizes DOE INFUSE-supported work between HB11 Energy and the University of Rochester’s TriForce Institute to improve computational modeling of advanced fusion fuels, especially proton–boron-11 (p- 11 B). The project extended the TriForce particle-in-cell/Monte Carlo collision code to include physics needed for dense, high-temperature p- 11 B burn studies, including p- 11 B fusion reactions, three-alpha-particle reaction products, relativistic Coulomb collisions, large-angle nuclear scattering, bremsstrahlung radiation, inverse bremsstrahlung absorption, and photon transport. The upgraded models were verified against focused physics tests and against known deuterium–tritium burn behavior. The study then used one-dimensional spherical simulations to estimate the conditions required for thermonuclear burn propagation in isochoric p- 11 B fuel. The calculations found that burn propagation is possible in the model, but only under very extreme hot-spot conditions, such as about 7000 g/cm 3 at 500 keV or 9000 g/cm 3 at 300 keV for a 20-micron hot spot. These conditions are much more demanding than current demonstrated inertial confinement fusion hot spots. The report concludes that the INFUSE collaboration successfully advanced kinetic and radiation modeling capabilities for p- 11 B fusion and provided useful estimates of ignition requirements. However, the simulated fuel gains remain below what would be needed for practical inertial fusion energy, and further work is needed to reconcile differences among kinetic, radiation-hydrodynamic, and analytic models and to identify more achievable target designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1983

Particle size distributions in Saturn's rings from Voyager 1 radio occultation

Information on Saturn ring particle sizes obtained with the Voyager 1 ring occultation experiment is discussed. The theory underlying the determination of the particle size distribution is presented, including differential extinction and inversion of the scattered signal. Experimental observations and results for the observed spectra, differential cross sections, suprameter and sub- to suprameter size distributions are presented. The size and mass distributions both cut off sharply at about 4-5 m; the mass distribution peaks over the 3-4 m size range for four ring system features at 1.35, 1.51, 2.01, and 2.12 Saturn radii. A power-law type model is consistent with the data over a limited size range of 0.01 to 1 m. The fractional contribution of the suprameter particles to the microwave opacity for the four features appears to be about 1/3, 1/3, 2/3, and 1, respectively, and their cumulative surface mass per unit area are about 11, 16, 41, and 132 g/sq cm if the particles are solid water ice.

Marouf, E. A.↗
NASA NTRS1994

The 1993 multiwavelength campaign on 3C 279: The radio to gamma-ray energy distribution inlow state

Simultaneous observations of 3C 279 at radio, millimeter, near-infrared, optical, ultraviolet (with IUE) and X-ray (with ROSAT) wavelengths were obtained in 1992 December-1993 January, during a three week pointing at the source by the Compton Gamma Ray Observatory. The blazar was in a quiescent or 'low' state during this period. Comparing the multiwavelength energy distribution to that from 1991 June, when 3C 279 was in its brightest recorded gamma-ray state, we find the following: (1) 3C 279 faded dramatically at all frequencies above 10(exp 14) Hz, while the flux variations at low frequencies (radio to millimeter wavelengths) were minor. (2) The near-infrared-optical-ultraviolet spectral shape was softer (steeper) in the quiescent state, and the X-ray spectra also appear softer, although the spectral indix measured by ROSAT refer to a lower energy band than that measured earlier with Ginga. (3) The ratio of the gamma-ray luminosity to that across all other frequencies decreased from a value of approximately equal to 10 in the flaring state to a value approximately equal to 1 in the quiescent state. These findings imply that the production of gamma-rays is closely related to the optical-ultraviolet continuum, in agreement with models where gamma-rays are produced through inverse Compton (IC) scattering by relativistic electrons emitting the synchrotron continuum. The observed nonlinear relation between the synchrotron and IC requires both a change in the electron spectrum and an associated change in the seed photons.

Maraschi, L.↗
NASA NTRS2013

A Method for Localizing Energy Dissipation in Blazars Using Fermi Variability

The distance of the Fermi-detected blazar gamma-ray emission site from the supermassive black hole is a matter of active debate. Here we present a method for testing if the GeV emission of powerful blazars is produced within the sub-pc scale broad line region (BLR) or farther out in the pc-scale molecular torus (MT) environment. If the GeV emission takes place within the BLR, the inverse Compton (IC) scattering of the BLR ultraviolet (UV) seed photons that produces the gamma-rays takes place at the onset of the Klein-Nishina regime. This causes the electron cooling time to become practically energy independent and the variation of the gamma-ray emission to be almost achromatic. If on the other hand the -ray emission is produced farther out in the pc-scale MT, the IC scattering of the infrared (IR) MT seed photons that produces the gamma-rays takes place in the Thomson regime, resulting to energy-dependent electron cooling times, manifested as faster cooling times for higher Fermi energies. We demonstrate these characteristics and discuss the applicability and limitations of our method.

Dotson, Amanda↗
NASA NTRS1993

A general rough-surface inversion algorithm: Theory and application to SAR data

Rough-surface inversion has significant applications in interpretation of SAR data obtained over bare soil surfaces and agricultural lands. Due to the sparsity of data and the large pixel size in SAR applications, it is not feasible to carry out inversions based on numerical scattering models. The alternative is to use parameter estimation techniques based on approximate analytical or empirical models. Hence, there are two issues to be addressed, namely, what model to choose and what estimation algorithm to apply. Here, a small perturbation model (SPM) is used to express the backscattering coefficients of the rough surface in terms of three surface parameters. The algorithm used to estimate these parameters is based on a nonlinear least-squares criterion. The least-squares optimization methods are widely used in estimation theory, but the distinguishing factor for SAR applications is incorporating the stochastic nature of both the unknown parameters and the data into formulation, which will be discussed in detail. The algorithm is tested with synthetic data, and several Newton-type least-squares minimization methods are discussed to compare their convergence characteristics. Finally, the algorithm is applied to multifrequency polarimetric SAR data obtained over some bare soil and agricultural fields. Results will be shown and compared to ground-truth measurements obtained from these areas. The strength of this general approach to inversion of SAR data is that it can be easily modified for use with any scattering model without changing any of the inversion steps. Note also that, for the same reason it is not limited to inversion of rough surfaces, and can be applied to any parameterized scattering process.

Moghaddam, M.↗
NASA NTRS1981

Measurements of the absorption coefficient of stratospheric aerosols

The absorption coefficients of stratospheric aerosols are measured using a variation on the integrating plate method. The technique is based on the decrease in the transparency of a substrate when an absorbing aerosol is deposited on it. A Lambert scatterer is placed behind the substrate to integrate forward scattered light and minimize the effect of scattering on the measurement. The low pressure in the stratosphere is used for the direct impaction of particles onto a narrow strip of opal glass. The eight samples collected had a median value of 4 x 10 to the -9th m with an uncertainty of + or - 5 x 10 to the -9th m. If this absorption is due to graphitic carbon, then its concentration is estimated at about 0.4 ng/cu m, or about 0.25% of the total aerosol mass concentration. Estimates of the aerosol scattering coefficients based on satellite extinction inversions result in an aerosol single-scattering albedo in the range of 0.96-1.0.

Ogren, J. A.↗
NASA NTRS1976

The solar occultation technique for remote sensing of particulates in the earth's atmosphere. I - The inversion of horizon radiances from space

The aerosol scattering coefficient as a function of height can be recovered from a direct inversion of the single-scattering horizon radiance provided the sun is above the horizon and an independent measurement of extinction as a function of height is made. Aerosol detection is effected by means of spacecraft measurements of the horizon radiance made during periods of spacecraft twilight. A solar occultation technique which allows the twilight measurements to be made when the sun is still above the horizon greatly reduces the complexity of the inversion problem. The second part of the paper reports on the use of a coronograph aboard Skylab to photograph the horizon just before spacecraft twilight in order to monitor the aerosol component above the tropopause. The coronograph picture, centered on 26.5 degrees E longitude and 63.0 degrees S latitude, shows that the aerosol layer peaks at a height of 48 plus or minus 1 km.

Schuerman, D. W.↗
NASA NTRS1991

Inverse problems in diffraction

A two-dimensional problem of diffraction of a plane electromagnetic wave on a smooth 2 pi-periodic surface is considered. A numerical algorithm solving this problem is developed. An inverse problem of determination of the shape of 2 pi-periodic surface using the performance data of reverse scattering is considered. The inverse problem was solved by means of minimization of the residual functional with the help of the gradient descent method. The initial data were calculated with the help of the numerical method. On each step of the iterative method of minimization, the residual functional was calculated approximately with the help of the small slope method. The examples of the shape determination are considered.

Mikheev, Andrew G.↗
NASA NTRS2019

Observation of inverse Compton emission from a long γ-ray burst

Long-duration γ-ray bursts (GRBs) originate from ultra-relativistic jets launched from the collapsing cores of dying massive stars. They are characterized by an initial phase of bright and highly variable radiation in the kiloelectronvolt-to-megaelectronvolt band, which is probably produced within the jet and lasts from milliseconds to minutes, known as the prompt emission. Subsequently, the interaction of the jet with the surrounding medium generates shock waves that are responsible for the afterglow emission, which lasts from days to months and occurs over a broad energy range from the radio to the gigaelectronvolt bands. The afterglow emission is generally well explained as synchrotron radiation emitted by electrons accelerated by the external shock. Recently, intense long-lasting emission between 0.2 and 1 teraelectronvolts was observed from GRB 190114C. Here we report multifrequency observations of GRB 190114C, and study the evolution in time of the GRB emission across 17 orders of magnitude in energy, from 5 × 10^(−6) to 10^(12) electronvolts. We find that the broadband spectral energy distribution is double-peaked, with the teraelectronvolt emission constituting a distinct spectral component with power comparable to the synchrotron component. This component is associated with the afterglow and is satisfactorily explained by inverse Compton up-scattering of synchrotron photons by high-energy electrons. We find that the conditions required to account for the observed teraelectronvolt component are typical for GRBs, supporting the possibility that inverse Compton emission is commonly produced in GRBs.

P. Veres↗
NASA NTRS1972

A review of some aspects of inferring the ozone profile by inversion of ultraviolet radiance measurements

The mathematical inversion of light-scattering observations to obtain the atmospheric ozone profile is discussed in terms of the filtering properties of the physical and mathematical processes for different spatial scales. Within this context, it is shown that the physical process of scattering acts as a low pass filter; which transfers large-scale profile information efficiently to radiance observations but very strongly attenuates small- or fine-scale profile information. To avoid domination of the mathematical inversion by the random error of radiance measurements, an equivalent spatial-scale filtering in the inversion procedure is essential. The available evidence suggests that mathematical inversion to obtain the low level ozone profile below 25 to 30 km is either inferior to or no better than the statistical estimation of the profile using total ozone as predictor. However, inversion profiles for high level ozone above 25 to 30 km appear to have moderately good accuracy.

Mateer, C. L.↗
NASA NTRS1977

Note on the forward-scatter approximation

An asymptotic expansion in inverse powers of the wave number is derived for an integral of a type often encountered in the theory of wave propagation in inhomogeneous media. The procedure, which is essentially a forward-scatter approximation, yields all the terms of the expansion. In contrast, the conventional forward-scatter approximation is found to yield correctly only the first term of the expansion.

Wenzel, A. R.↗
NASA NTRS1973

Determination of Atmospheric Aerosol Characteristics from the Polarization of Scattered Radiation

Aerosols affect the polarization of radiation in scattering, hence measured polarization can be used to infer the nature of the particles. Size distribution, particle shape, real and absorption parts of the complex refractive index affect the scattering. From Lorenz-Mie calculations of the 4-Stokes parameters as a function of scattering angle for various wavelengths the following polarization parameters were plotted: total intensity, intensity of polarization in plane of observation, intensity perpendicular to the plane of observation, polarization ratio, polarization (using all 4-Stokes parameters), plane of the polarization ellipse and its ellipticity. A six-component log-Gaussian size distribution model was used to study the effects of the nature of the polarization due to variations in the size distribution and complex refractive index. Though a rigorous inversion from measurements of scattering to detailed specification of aerosol characteristics is not possible, considerable information about the nature of the aerosols can be obtained. Only single scattering from aerosols was used in this paper. Also, the background due to Rayleigh gas scattering, the reduction of effects as a result of multiple scattering and polarization effects of possible ground background (airborne platforms) were not included.

Harris, F. S., Jr.↗
DOE OSTI2025

Harnessing Ultra-Intense Long-Wave Infrared Lasers: New Frontiers in Fundamental and Applied Research

This review explores two main topics: the state-of-the-art and emerging capabilities of high-peak-power, ultrafast (picosecond and femtosecond) long-wave infrared (LWIR) laser technology based on CO2 gas laser amplifiers, and the current and advanced scientific applications of this laser class. The discussion is grounded in expertise gained at the Accelerator Test Facility (ATF) of Brookhaven National Laboratory (BNL), a leading center for ultrafast, high-power CO2 laser development and a National User Facility with a strong track record in high-intensity physics experiments. We begin by reviewing the status of 9–10 μm CO2 laser technology and its applications, before exploring potential breakthroughs, including the realization of 100 terawatt femtosecond pulses. These advancements will drive ongoing research in electron and ion acceleration in plasma, along with applications in secondary radiation sources and atmospheric energy transport. Throughout the review, we highlight how wavelength scaling of physical effects enhances the capabilities of ultra-intense lasers in the LWIR spectrum, expanding the frontiers of both fundamental and applied science.

43 PARTICLE ACCELERATORS↗