Search NASA⌕ Search

SEARCH · Search NASA

Results for “LaRC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Development of Slat-gap and Slat-cove Filler Treatments for Noise Reduction Assessment on the High Lift Common Research Model in the NASA LaRC 14x22

Airframe noise is an important issue during the approach and landing phases of flight because engines are throttled back, and airframe sources become an equal or greater contributor to environmental noise. The leading-edge slat component of the high-lift system for transport aircraft has been identified as a prominent source of airframe noise. Noise production mechanisms and potential treatments to mitigate airframe noise have been areas of active research for nearly three decades. Two promising technologies for slat noise reduction are the slat-gap filler (SGF) and slat-cove filler (SCF). Previous work was done using a 2D section of a transport class aircraft wing to demonstrate their feasibility via benchtop and computational models. A wind tunnel test campaign was recently undertaken to test the SGF and SCF technologies in a flight-like environment by installing dynamically scaled treatments on the 10%-scale High-Lift Common Research Model (CRM-HL), which is representative of a commercial twin-aisle transport aircraft. Advancement of the SGF and SCF technologies to overcome challenges of integration with 3D airframe structures, computational simulations of the CRM-HL predicting the aerodynamic and aeroacoustic performance and structural loads, and design of wind tunnel model hardware with features accommodating noise treatments were conducted in parallel. Details of innovations in the SGF and SCF technologies for 3D airframe feasibility will be described. The loads the treatments must sustain in flight and the influence of those loads on the design is also discussed. Finally, the design of wing leading-edge assemblies to treat the 10% CRM-HL with dynamically scaled SGF and SCF components is presented. The treatments were successfully tested in 2020/2021 providing a demonstration of leading-edge noise reduction using components that would allow slat articulation.

airframe noise reduction↗
NASA NTRSDate not supplied

Advances in PSP Testing in LaRC High Reynolds Number Facilities

The use of luminescent coatings for the global measurement of surface aerodynamic properties at full-flight Reynolds numbers has been ongoing at the NASA Langley Research Center since the late 1990s, beginning with Temperature Sensitive Paint (TSP) for boundary layer analysis at the 0.3-m Transonic Cryogenics Tunnel. Since then, significant work has been made to extend these measurements to pressure using Pressure Sensitive Paint (PSP) as well as develop systems for application in larger scale, full-flight Reynolds number facilities, such as the National Transonic Facility (NTF). Recently, a system for the measurement of time-resolved pressure using recently developed unsteady PSP (uPSP) formulations has been designed and implemented in the Transonic Dynamics Tunnel (TDT). The use of PSP (or uPSP) in either of these large scale, full-fight Reynolds number wind tunnels is complicated by the fact that both facilities operate best in oxygen deficient environments; however, the PSP technique relies on the presence of oxygen to work. The NTF is typically operated in cryogenic conditions, which is achieved using liquid nitrogen. In this facility, temperatures can reach as low as 116 K (-250 °F) with nominal oxygen concentrations of less than 50 ppm. This has resulted in the development of specialized PSP formulations that can operate in the cryogenic environment with the introduction of low amounts of oxygen (typically less than 2000 ppm) for PSP response. Likewise, to achieve full-flight Reynolds number conditions in the TDT, the atmosphere in the tunnel is replaced with a “heavy gas” of R-134A (1,1,1,2-tetrafluoroethane), which also has minimal oxygen native in the flow. The use of uPSP in this case will also depend on the introduction of trace amounts of oxygen, with the precise concentrations to be determined in an upcoming test. This presentation will describe some recent advancements that have been made for PSP measurements in both facilities. For the NTF system, there has been significant development of enhanced lighting for use at cryogenic conditions, as well as improvements in the application efficiency of the PSP. Furthermore, there are efforts underway to incorporate advanced data analysis techniques to acquire additional surface aerodynamic properties using the PSP technique that can yield not only improved experimental efficiency, but also provide data needed for next generation vehicle design and development. For the uPSP system in TDT, significant efforts to improve the data transfer rates to a high-performance computing environment for analysis are underway and performance and initial results from the system in the heavy-gas environment will be presented.

Pressure Sensitive Paint↗
NASA NTRSDate not supplied

NASA LaRC Contribution to the High Angle Working Group of the Third Aeroelastic Prediction Workshop: BSCW Shock Buffet

FUN3D Core Capabilities - Established as a research code in late 1980s; now supports numerous internal and external efforts across the speed range - Solves 2D/3D steady and unsteady Euler and RANS equations on node-based mixed element grids for compressible and incompressible flows - General dynamic mesh capability: any combination of rigid / overset / morphing grids, including 6-DOF effects - Aeroelastic modeling using mode shapes, full FEM, etc. - Constrained / multipoint adjoint-based design and mesh adaptation - Distributed development team using agile/extreme software practices including 24/7 regression, performance testing - Capabilities fully integrated, online documentation, training videos, tutorials

Pawel Chwalowski↗
NASA NTRS2023

Experimental Aeroheating Study in NASA LaRC 20-Inch Mach 6 Air Tunnel: Discrete Roughness on BOLT – Test 7071

An experimental study of the effect of discrete roughness (trips) on boundary layer transition was conducted in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel on the BOLT shape. This study was intended to obtain results that could eventually be compared against experimental results from other facilities, as well as from flight. The trip locations for the present study were selected to correspond to those used for the flight vehicle, but the heights of these discrete roughness elements were varied. Infrared thermography was used to obtain images of the effect of these trips on the behavior of the boundary layer. This report is intended as a quick release of experimental results.

hypersonic↗