Search NASA⌕ Search

SEARCH · Search NASA

Results for “Land-based Wind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Technology Innovation Pathways for Distributed Wind Balance-of-System Cost Reduction

This exploratory analysis characterizes the balance-of-system (BOS) cost reduction opportunity for small, commercial, medium, and large distributed wind systems. To do this, we used the National Renewable Energy Laboratory’s (NREL’s) Land-based Balance of System Systems Engineering (LandBOSSE) model (Eberle et al. 2019). This model calculates the capital expenditures (CapEx) associated with installation and the system components (e.g., foundation and electrical infrastructure) other than the rotor nacelle assembly and tower. Then, building on the cost reduction potential assessment, we provide a more qualitative evaluation of prospective technology innovation concepts that may enable realization of those cost reductions for distributed wind systems.

17 WIND ENERGY↗
DOE OSTI2020

Feasibility of Ocean-Based Renewable Energy in the Gulf of Mexico

This paper summarizes a comprehensive feasibility assessment of six offshore renewable energy sources in the Gulf of Mexico (GOM) to potentially provide utility-scale electricity from the Outer Continental Shelf (federal waters) and state waters to land-based grids. Overall, the primary objective is to inform future energy planning. The authors evaluated offshore wind, wave energy, tidal energy, ocean-based solar photovoltaics (PV), ocean current, and ocean thermal energy conversion. Of these energy resources, offshore wind was the most viable option and was the focus of the second part of the study. The technical challenges of developing offshore wind in the GOM are discussed including hurricane design for turbines and substructures, as well as turbine solutions to overcome lower wind regimes. In addition, advantages to offshore wind development in the GOM are described including proximity to oil and gas supply chains. Economic analysis using established cost models at the National Renewable Energy Laboratory identified hypothetical project locations where net value of offshore wind was the highest, and the levelized cost of energy (LCOE) was calculated for three sites: Port Isabel, Port Arthur, and Pensacola. Offshore wind LCOE in the GOM was found to be higher than those in sites along the north and mid-Atlantic coasts, but decreasing cost trajectories indicate the possibility of economic viability for locations in Texas and west Louisiana after 2030. The extrapolated 2030 LCOE values range from 73 dollars per MWh (Site 1, Port Isabel) and 79 dollars per MWh (Site 3, Port Arthur) to 91 dollars per MWh (Site 5, Pensacola).

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Development of an open-source segmented blade design tool

As wind turbines continue to grow ever larger to reduce the cost of energy, their blades follow suit, with the largest commercial offshore blades extending past 100 m. Massive blades such as these raise key transportation and manufacturing challenges, especially for land-based turbines. Segmented blades are one solution and are garnering increased industry and research interest. In this work, a detailed mechanical joint model is integrated into the Wind-Plant Integrated System Design and Engineering Model (WISDEM ® ), which will facilitate future segmented blade research and optimization. WISDEM is used to design a wind turbine with 100-m segmented blades. This wind turbine design is compared to other machines with 100-m monolithic blades designed for rail-transportability. The designs are compared in terms of blade mass and cost, turbine capital cost, annual energy production, and levelized cost of energy, with monolithic designs being the lightest and most economical. However, this result may vary by wind plant location. A variety of segmentation joint types exist, and they will inevitably vary in parameters such as cost, spanwise location, and physical characteristics. This work examines the sensitivity of wind turbine design drivers and annual energy production to a variety of the aforementioned parameters, using the open-source wind turbine design codes OpenFAST and WISDEM, finding that joint mass, stiffness, and location can have significant effects on design drivers.

17 WIND ENERGY↗
DOE OSTI2023

Large Castings for Wind Turbines

This analysis uses the Renewable Energy Materials Properties Database to examine supply considerations for two parts of a wind turbine, the hub and bedplate. Each of these cast iron components is cast as a single large piece up to 4 m across (for land-based turbines) or 8 m (offshore). Close to 5,000 hubs and bedplates have been installed per year in the United States and meeting the nation's clean energy goals could increase that number to 12,000-20,000 per year in the next decade. These parts are currently imported, but growing demand for wind turbine components may provide opportunities for domestic manufacturers.

17 WIND ENERGY↗
DOE OSTI2023

Main Bearing Replacement and Damage - A Field Data Study on 15 Gigawatts of Wind Energy Capacity

This study seeks to establish a comprehensive baseline of knowledge for the replacement and damage of main bearings in wind turbines. The purpose of this report is to provide a high-level summary of the data set, methodology, and results of this work. Full technical details and an extended analysis will be made available in a future publication. We collected data on main bearing replacements and reported damage from industrial partners based in Europe and the United States. In total, we obtained data for 167 wind power plants, with a combined capacity of 15.3 gigawatts (GW). Most of the data set was comprised of land-based, three-point mount, spherical roller bearings. Within this data set were 689 instances of main bearing replacement. Analysis was undertaken in two parts: first, a statistical analysis of the main bearing time-to-replacement data using survival analysis techniques; second, quantitative and qualitative analyses of the obtained damage information. Our results showed that 10% of a fixed main bearing population would be expected to have been replaced by 10.5 years. This is close to half of the 20-year design value. Fitted parametric distributions then indicated that by year 20, between 22% and 25% of main bearings are expected to have been replaced. Analysis of the damage reports revealed spalling to be the main type of damage listed. The additional presence of surface damage in the collected data indicates that at least part of the spalling cases are likely due to surface-initiated rolling contact fatigue. At this stage is not clear what proportion of spalling cases result from "wear induced", surface-initiated and subsurface-initiated rolling contact fatigue. While this work provides important insights into the current state of main bearing replacements and damage, many questions remain. An ongoing and expanding data collection and analysis effort focused on wind turbine main bearings is therefore recommended.

17 WIND ENERGY↗
DOE OSTI2020

ORBIT: Offshore Renewables Balance-of-System and Installation Tool

This report describes the Offshore Renewables Balance-of-system Installation Tool ("ORBIT"), a new model developed by the National Renewable Energy Laboratory (NREL) to evaluate the balance-of-system (BOS) costs associated with offshore wind projects. In the context of wind energy projects BOS costs encompass all expenses required to construct a project other than the capital expenditures (CapEx) of the turbines and towers, including the procurement costs for all other components (such as substructures, cables, and electrical infrastructure), offshore and land-based construction costs, port costs, site surveying fees, permitting fees, and leasing fees are all categorized as BOS costs. BOS costs significantly contribute to the levelized cost of energy (LCOE) for offshore wind, typically comprising over 50\% of the CapEx for a fixed-bottom offshore wind project and 60\% for a floating project. In addition, technology solutions and installation methods vary drastically between projects as they are impacted by factors such as vessel availability, geographic considerations and site geotechnical conditions. These effects require a model with appropriate fidelity to understand how these costs scale as turbine rating increases and the offshore wind supply chain, particularly offshore construction vessels, is expanded. For offshore wind, cost savings attributed to increased turbine rating are primarily realized through BOS procurement and project installation as fewer substructures and less cable are required. BOS costs represent both a modeling challenge, as well as an opportunity, for project developers to optimize solutions to reduce costs. It is critical to understand how these costs are affected by novel technologies, innovative installation processes, and operational constraints in order identify meaningful cost reductions for offshore wind energy.

17 WIND ENERGY↗
DOE OSTI2020

Tuning of Nacelle Feedback Gains for Floating Wind Turbine Controllers Using a Two-DOF Model

Designing a collective blade pitch controller for floating offshore wind turbines (FOWTs) poses unique challenges due to the interaction of the controller with the dynamics of the platform. The controller must also handle the competing objectives of power production performance and fatigue load management. Existing solutions either detune the controller with the result of slowed response, make use of complicated tuning methods, or incorporate a nacelle velocity feedback gain. With the goal of developing a simple control tuning method for the general FOWT researcher that is easily extensible to a wide array of turbine and hull configurations, this last idea is built upon by proposing a simple tuning strategy for the feedback gain. This strategy uses a two degree-of-freedom (DoF) turbine model that considers tower-top fore-aft and rotor angular displacements. For evaluation, the nacelle velocity term is added to an existing gain scheduled proportional-integral controller as a proportional gain. The modified controller is then compared to baseline land-based and detuned controllers on an example system for several load cases. First-pass results are favorable, demonstrating how researchers can use the proposed tuning method to efficiently schedule gains for adequate controller performance as they investigate new FOWT configurations.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2021

Modal dynamics and flutter analysis of floating offshore vertical axis wind turbines

Floating platforms provide vertical axis wind turbines (VAWTs) significant advantages over offshore horizontal axis wind turbines, which has led to increased research interest in offshore VAWT technology. Here, this paper examines dynamic stability of floating VAWTs and presents structural dynamic and aero-elastic flutter analysis of utility-scale 5 MW floating VAWTs by coupling a rotor finite element model with a linearized model for the floating system. The coupled floating VAWT model is utilized to study the effects of tower height, number of blades, blade tapering scheme, and impacts of the floating platform on modal properties and flutter. The study provides important new results and guidance to floating VAWT designers: (1) tower height increase leads to lower tower frequencies more prone to resonance, (2) by moving from land-based foundations to a floating TLP foundation, tower-mode frequency is increased significantly (by 49%–68%) which mitigates resonance and increases the flutter RPM (154% increase), (3) increasing the number of blades reduces the tower mode frequencies for both land-based and floating configuration, and (4) blade chord tapering can have a significant impact on increasing the tower mode flutter RPM. Further, analysis of low-frequency rigid body modes shows a safe, higher flutter RPM relative to the operating RPM.

17 WIND ENERGY↗
DOE OSTI2020

Report of the Atmosphere to Electrons Land-Based Mesoscale-to-Microscale Coupling Project (FY2020)

The overall goal of the Mesoscale-to-Microscale Coupling (MMC) project is to improve coupling between mesoscale and microscale simulations via improved guidance and new strategies for setting up simulations and for the development of new tools that can be used across the community. Including the mesoscale forcing is critical to modeling the full energy transfer across scales in the atmosphere. The project-specific objectives include: 1) To apply rigorous verification and validation (V&V) techniques to the new modeling tools that are developed as part of the project to ensure the accuracy of our codes and results and to develop estimates of the relative uncertainty. 2) To improve computational performance of the coupled MMC models through the development of methods that can be used to reduce turbulence spin-up time and hence the size of computational domains. 3) To improve representation of the surface layer in microscale models to enhance simulations of hub-height wind speed. 4) To develop guidance for the community describing the best ways to couple mesoscale and microscale models, including specific spatial scales at which the handoff to the microscale model should occur. 5) To prepare documentation and a suite of software tools that can be used across the community. And 6) To transition MMC research to the offshore environment. Major progress was made in each of these areas during FY20. The land-based portion of the project is reported herein, while the offshore portion will be reported separately. The team continued to advance the MMC tools and methodologies as well as to document their performance in journal papers and conference presentations, although several planned conferences were cancelled due to the COVID-19 pandemic.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Doppler Lidar Motion-Correction (DLMC) Value-Added Product Report

The U.S. Department of Energy Atmospheric Radiation Measurement (ARM) second ARM Mobile Facility (AMF2) Doppler lidar (S/N 0319-160) was deployed on the German ice breaker Polarstern during the Multidisciplinary Drifting Observatory for the Study of Arctic Climate (MOSAiC) campaign during 2019-2020 (see Figure 1). This was the first deployment of the new AMF2 Doppler lidar, as well as the first ship-based deployment of a Doppler lidar (DL) by ARM. In contrast to land-based deployments, the lidar’s heading (a.k.a. home point) and tilt are constantly changing, and lidar’s radial velocity measurements are impacted by the ship’s motion. Since the beam directions are reported relative to the instrument’s frame of reference, derivation of higher-order data products such as wind speed and direction require that the lidar’s attitude and translational velocity be properly accounted for. The Doppler Lidar Motion-Correction (DLMC) Value-Added-Product (VAP) was developed specifically for ship-based deployments of the Doppler lidar. This VAP combines raw uncorrected data from the DL and simultaneous measurements from the ARM Navigation system (NAV) (Walton 2019) to transform the beam angles from the lidar coordinate system to an Earth-fixed coordinate system. The VAP also removes the contribution of the lidar’s platform velocity from the radial velocity measurements. This report documents the methods used by the DLMC to perform these corrections.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Improving High Resolution Offshore Wind Resource Assessments and Forecasts using Observations in the MA/RI Lease Areas

The third Wind Forecast Improvement Project (WFIP3) sought to improve understanding of the physical phenomena in the atmosphere and ocean that dictate the structure and variability of wind and thermodynamic fields within the Marine Atmospheric Boundary Layer (MABL). WFIP3 conducted a comprehensive 18-month observational study over the Northeast U.S. outer continental shelf, a high use coastal zone, using a 3-D multiscale sensor array to highly resolve the temporal, vertical, and horizontal structure of the coupled atmospheric and oceanic boundary layers. Multiple land-based study sites adjacent to the coastal ocean observed surface meteorology and vertical profiles of atmospheric properties via passive infrared and microwave radiometers, active lidars and radars, and radiosondes. At sea, an array of surface flux buoys and two vertical profiling lidar buoys observed both atmospheric and oceanic properties, augmented by land-based oceanographic radar systems and routine ship-based surveys. Intensive observations of the MABL over the ocean was done from an air-sea interaction flux tower and extended deployments of a large barge platform. WFIP3 focused on mesoscale and sub-mesoscale flows -- including sea breezes, low-level jets, low-level clouds, and coastal storms -- and the ability of advanced numerical model parameterizations to represent them within fully coupled oceanic and atmospheric modeling systems and foundational weather forecast models. Numerous critical forecasting phenomena were observed, however the project was terminated prior to the completion of the field observational period and the analysis period.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Observations of high-time-resolution and size-resolved aerosol chemical composition and microphysics in the central Arctic: implications for climate-relevant particle properties

Abstract. Aerosols play a critical role in the Arctic's radiative balance, influencing solar radiation and cloud formation. Limited observations in the central Arctic leave gaps in understanding aerosol dynamics year-round, affecting model predictions of climate-relevant aerosol properties. Here, we present the first annual high-time-resolution observations of submicron aerosol chemical composition in the central Arctic during the Arctic Ocean 2018 (AO2018) and the 2019–2020 Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expeditions. Seasonal variations in the aerosol mass concentrations and chemical composition in the central Arctic were found to be driven by typical Arctic seasonal regimes and resemble those of pan-Arctic land-based stations. Organic aerosols dominated the pristine summer, while anthropogenic sulfate prevailed in autumn and spring under haze conditions. Ammonium, which impacts aerosol acidity, was consistently less abundant, relative to sulfate, in the central Arctic compared to lower latitudes of the Arctic. Cyclonic (storm) activity was found to have a significant influence on aerosol variability by enhancing emissions from local sources and the transport of remote aerosol. Local wind-generated particles contributed up to 80 % (20 %) of the cloud condensation nuclei population in autumn (spring). While the analysis presented herein provides the current central Arctic aerosol baseline, which will serve to improve climate model predictions in the region, it also underscores the importance of integrating short-timescale processes, such as seasonal wind-driven aerosol sources from blowing snow and open leads/ocean in model simulations. This is particularly important, given the decline in mid-latitude anthropogenic emissions and the increase in local ones.

Heutte, Benjamin (ORCID:0000000173727460)↗
DOE OSTI2026

Improving Process Level Understanding of Boundary Layer Winds over the Northeast U.S. Shelf: The Third Wind Forecast Improvement Project (WFIP3)

The third Wind Forecast Improvement Project (WFIP3), a U.S. Department of Energy and National Oceanic and Atmospheric Administration sponsored investigation, sought to improve understanding of the physical phenomena in the atmosphere and ocean that dictate the structure and variability of wind and thermodynamic fields within the marine atmospheric boundary layer. WFIP3 focused on mesoscale and submesoscale flows -- including sea breezes, low-level jets, low-level clouds, and coastal storms -- and the ability of advanced numerical model parameterizations to represent them within fully coupled oceanic and atmospheric modeling systems and foundational weather forecast models. WFIP3 conducted a comprehensive 18-month observational study over the Northeast U.S. outer continental shelf, a high-use coastal zone, using a 3D multiscale sensor array to highly resolve the temporal, vertical, and horizontal structure of the coupled atmospheric and oceanic boundary layers. Multiple land-based study sites adjacent to the coastal ocean observed surface meteorology and vertical profiles of atmospheric properties via passive infrared and microwave radiometers, active lidars and radars, and radiosondes. At sea, an array of surface flux buoys and two vertical profiling lidar buoys observed both atmospheric and oceanic properties, augmented by land-based oceanographic radar systems and routine ship-based surveys. Intensive observations of the marine atmospheric boundary layer over the ocean was done from an air-sea interaction flux tower and extended deployments of a large autonomous barge platform. Numerous critical forecasting phenomena were observed that are being evaluated within regional coupled and uncoupled modeling systems, including the National Oceanic and Atmospheric Administration's foundational High-Resolution Rapid Refresh forecast model.

Kirincich, Anthony↗
DOE OSTI2025

Land-based resources for engineered carbon dioxide removal in the United States exceed the expected needs

Gigatonne-scale atmospheric carbon dioxide removal (CDR), alongside deep emission cuts, is critical to stabilizing the climate. However, some of the most scalable CDR technologies are also the most land intensive. Here, we examine whether adequate land resources exist in the contiguous United States to meet CDR targets when prioritizing grid emissions reduction, food production, and the protection of sensitive ecosystems. We focus on biomass carbon removal and storage (BiCRS) and direct air capture and storage (DACS) and show that suitable lands exceed the expected needs: 37.6 million hectares of land are available for BiCRS, resulting in 0.26 GtCO 2 of CDR/year, and 34 million hectares are suitable for wind- and solar-powered DACS, resulting in 4.8 GtCO 2 of CDR/year if facilities are co-located with geologic CO 2 storage. We identify biomass and energy supply hotspots to meet CDR targets while ensuring land protection and minimizing land competition.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Spatiotemporal Variations in the Characteristics of Mesoscale Convective Systems Over Indian Monsoon Zone

Here, this study examines cloud and precipitation properties of mesoscale convective systems (MCSs) in the Indian monsoon zone using 6 years of high-resolution satellite-based tracking data. MCSs exhibit strong regional and seasonal variations, peaking during the summer monsoon (June–September). Concentrated along a southeast-northwest band of the monsoon trough, MCS contribute 40%–70% of total precipitation and predominantly move westward at an average speed of 6.3 m s -1 . Long-lived MCSs (> 40 hr), although 10 times less frequent than short-lived MCSs (5–20 hr), produce 2–3 times more rainfall. Longer MCS lifespans and higher rainfall are associated with stronger deep-layer wind shear and enhanced lower free-tropospheric moisture at initiation. Land and ocean MCSs exhibit distinct diurnal cycles. Most land-based MCSs initiate around 16 LT and mature at 18 LT, whereas Bay of Bengal (BoB) MCSs initiate between 04 and 06 LT and peak by 14 LT. Convective precipitations from MCSs significantly surpasses that from non-MCSs systems, emphasizing their critical role in intense monsoon rainfall. Short- and long-lived MCSs showed distinct lifecycle evolution. Long-lived MCSs over the BoB show 37% larger cold-cloud shields, 44% larger precipitation feature areas, and 33% higher rain rates than their land counterparts, yielding 67% more total rainfall. These BoB MCSs also grow faster and experience more frequent cloud mergers early in their lifecycle. These findings offer critical insights into monsoonal MCSs lifecycle evolution, providing observational constraints for improving model simulations of monsoonal convection.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Data for "Land-based Resources for Engineered Carbon Dioxide Removal in the United States Exceed the Expected Needs"

Gigatonne-scale atmospheric carbon dioxide removal (CDR), alongside deep emission cuts, is critical to stabilizing the climate. However, some of the most scalable CDR technologies are also the most land intensive. Here, we examine whether adequate land resources exist in the contiguous United States to meet CDR targets when prioritizing grid emissions reduction, food production, and the protection of sensitive ecosystems. We focus on biomass carbon removal and storage (BiCRS) and direct air capture and storage (DACS) and show that suitable lands exceed the expected needs: 37.6 million hectares of land are available for BiCRS, resulting in 0.26 GtCO2 of CDR/year, and 34 million hectares are suitable for wind- and solar-powered DACS, resulting in 4.8 GtCO2 of CDR/year if facilities are co-located with geologic CO2 storage. We identify biomass and energy supply hotspots to meet CDR targets while ensuring land protection and minimizing land competition.

carbon↗
DOE OSTI2025

Seafloor Seismic Noise Patterns Across the Pacific Basin

Seismic hazard monitoring and global tomography efforts are improved by recording signals at a variety of distances and azimuths to maximize subsurface sampling. Although seismic networks provide good to excellent coverage on land, seafloor stations are still sparse. Inclusion of ocean-based data would greatly improve the global coverage of seismic networks, but the use of seafloor seismic data to complement land-based detection and characterization of events is complicated by the generally much higher ambient noise level in the ocean compared to that observed on land. This noise is driven primarily by sea surface waves and tides, but how seismic noise levels vary with location in the oceans is not well described. Here, in this work, we analyze the relationship between ocean surface wave height and seismic noise in the 0.4–4 Hz frequency band at ocean-bottom seismometer deployments across the Pacific basin. We find that a noise-to-responsiveness ratio (NRR)—the median noise level at a station divided by its sea surface wave height responsiveness—correlates negatively with detection success for large teleseismic earthquakes. Stations that are close to land, with relatively shallow ocean and low wind speed, often have lower NRR than open-ocean stations, but the connection between geographic location and earthquake detection success is imperfect.

58 GEOSCIENCES↗
DOE OSTI2024

WFIP3 High Frequency Radar / Processed Data

These data were collected by Kirincich as part of the DOE Wind Forecast Improvement Project, based on support from NOAA-IOOS, WHOI, and DOE. The data consist of estimates of the near-surface horizontal (East and North) ocean currents made via High Frequency (HF) radar-based remote sensing of the Ocean backscatter spectrum. The effective measurement depth of the WHOI HF radars is 0.5 m below the ocean surface. The WHOI HF radar system, as operated during the experiment, consisted of 4 land-based sites spaced at 30-40km intervals along the area spanning from Nantucket,MA to Narragansett,RI that operate at 16 MHz and 25 MHz systems (see Kirincich et al, 2019 and Kirincich et al 2022 for details). Received doppler spectra from each were processed using the advanced methods of Kirincich et al. 2012, and Kirincich et al 2019, and unpublished work Kirincich, 2024) into radial or elliptical velocity estimates every 30 min based on a 30 min averaging window.

17 WIND ENERGY↗