SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Automated substructuring in level 16 of NASTRAN was employed as a preface to the solution of a direct transient analysis. The DMAP ALTER statements written to adapt the substructuring for transient purposes are explained. Data recovery was accomplished with transfer functions. Proof of the success of the method is presented with an application to a missile structure.
A procedure for the absolute registration of earth images acquired by cameras on geosynchronous satellites is described. A conventional least squares process is used to estimate navigational parameters and camera pointing biases from observed minus computed landmark line and element numbers. These estimated parameters along with orbit and attitude dynamic models are used to register images, employing an automated grey-level correlation technique, inside the span represented by the landmark data. Experimental results obtained from processing the SMS-2 observation data base covering May 2, 1979 through May 20, 1979 show registration accuracies with a standard deviation of less than two pixels if the registration is within the landmark data span. It is also found that accurate registration can be expected for images obtained up to 48 hours outside of the landmark data span.
The Fault Tolerant Multiprocessor (FTMP) computer system was constructed using the Rockwell/Collins CAPS-6 processor. It is installed in the Avionics Integration Research Laboratory (AIRLAB) of NASA Langley Research Center. It is hosted by AIRLAB's System 10, a VAX 11/750, for the loading of programs and experimentation. The FTMP support software includes a cross compiler for a high level language called Automated Engineering Design (AED) System, an assembler for the CAPS-6 processor assembly language, and a linker. Access to this support software is through an automated remote access facility on the VAX which relieves the user of the burden of learning how to use the IBM 4381. This manual is a compilation of information about the FTMP support environment. It explains the FTMP software and support environment along many of the finer points of running programs on FTMP. This will be helpful to the researcher trying to run an experiment on FTMP and even to the person probing FTMP with fault injections. Much of the information in this manual can be found in other sources; we are only attempting to bring together the basic points in a single source. If the reader should need points clarified, there is a list of support documentation in the back of this manual.
Parallelized versions of genetic algorithms (GAs) are popular primarily for three reasons: the GA is an inherently parallel algorithm, typical GA applications are very compute intensive, and powerful computing platforms, especially Beowulf-style computing clusters, are becoming more affordable and easier to implement. In addition, the low communication bandwidth required allows the use of inexpensive networking hardware such as standard office ethernet. In this paper we describe a parallel GA and its use in automated high-level circuit design. Genetic algorithms are a type of trial-and-error search technique that are guided by principles of Darwinian evolution. Just as the genetic material of two living organisms can intermix to produce offspring that are better adapted to their environment, GAs expose genetic material, frequently strings of 1s and Os, to the forces of artificial evolution: selection, mutation, recombination, etc. GAs start with a pool of randomly-generated candidate solutions which are then tested and scored with respect to their utility. Solutions are then bred by probabilistically selecting high quality parents and recombining their genetic representations to produce offspring solutions. Offspring are typically subjected to a small amount of random mutation. After a pool of offspring is produced, this process iterates until a satisfactory solution is found or an iteration limit is reached. Genetic algorithms have been applied to a wide variety of problems in many fields, including chemistry, biology, and many engineering disciplines. There are many styles of parallelism used in implementing parallel GAs. One such method is called the master-slave or processor farm approach. In this technique, slave nodes are used solely to compute fitness evaluations (the most time consuming part). The master processor collects fitness scores from the nodes and performs the genetic operators (selection, reproduction, variation, etc.). Because of dependency issues in the GA, it is possible to have idle processors. However, as long as the load at each processing node is similar, the processors are kept busy nearly all of the time. In applying GAs to circuit design, a suitable genetic representation 'is that of a circuit-construction program. We discuss one such circuit-construction programming language and show how evolution can generate useful analog circuit designs. This language has the desirable property that virtually all sets of combinations of primitives result in valid circuit graphs. Our system allows circuit size (number of devices), circuit topology, and device values to be evolved. Using a parallel genetic algorithm and circuit simulation software, we present experimental results as applied to three analog filter and two amplifier design tasks. For example, a figure shows an 85 dB amplifier design evolved by our system, and another figure shows the performance of that circuit (gain and frequency response). In all tasks, our system is able to generate circuits that achieve the target specifications.
This paper explores methodology issues encountered in the analysis of flightcrew communications in aviation simulation research. Examples are provided by two recent studies which are compared on three issues: level of analysis, data definition, and interpretation of the results. The data discussed were collected in a study comparing two levels of aircraft automation. The first example is an investigation of how pilots' information transfer strategies differed as a function of automation during low and high-workload flight phases. The second study focuses on how crews managed actions in the two aircraft during a ten minute, high-workload flight segment. Results indicated that crews in the two aircraft differed in their strategies of information and action management. The differences are discussed in terms of their operational and research significance.
Trajectory-based operations (TBO) is a key concept in the Next Generation Air Transportation System transformation of the National Airspace System (NAS) that will increase the predictability and stability of traffic flows, support a common operational picture through the use of digital data sharing, facilitate more effective collaborative decision making between airspace users and air navigation service providers, and enable increased levels of integrated automation across the NAS. NASA has been developing trajectory-based systems to improve the efficiency of the NAS during specific phases of flight and is now also exploring Advanced 4-Dimensional Trajectory (4DT) operational concepts that will integrate these technologies and incorporate new technology where needed to create both automation and procedures to support gate-to-gate TBO. A TBO Prototype simulation toolkit has been developed that demonstrates initial functionality of an Advanced 4DT TBO concept. Pilot and controller subject matter experts (SMEs) were brought to the Air Traffic Operations Laboratory at NASA Langley Research Center for discussions on an Advanced 4DT operational concept and were provided an interactive demonstration of the TBO Prototype using four example scenarios. The SMEs provided feedback on potential operational, technological, and procedural opportunities and concerns. This paper describes an Advanced 4DT operational concept, the TBO Prototype, the demonstration scenarios and methods used, and the feedback obtained from the pilot and controller SMEs in this focus group activity.
Fiber optics has been a winning player in the game of high-speed communication and data transfer in cable connections. Yet, in free space RF has been the repeated choice of communication medium of the space industry. Investigating the benefits of free space optical communication over radio frequency is worthwhile. An increase in science data rate return capabilities could occur if optical communication is implemented. Optical communication systems also provide efficiencies in power, mass, and volume over RF systems1. Optical communication systems have been demonstrated from a satellite in orbit with the moon to earth, and resulted in the highest data rates ever seen through space (622Mbps)2. Because of these benefits, optical communication is far superior to RF. The HiDRA (High Data Rate Architecture) project is researching Passive Misalignment Mitigation of Dynamic Free Apace Optical Communication Links. The goal of this effort is to enable gigabit per second transmission of data in short range dynamic links (less than 100 meters). In practice this would enhance data rates between sites on the International Space Station with minimal size, weight, and power requirements. This paper will focus on an autonomous code and a hardware setup that will be used to fulfill the next step in the research being conducted. The free space optical communications pointing downfalls will be investigated. This was achieved by creating 5 python programs and a top-level code to automate this test.
Trajectory-based operations (TBO) is a key concept in the Next Generation Air Transportation System transformation of the National Airspace System (NAS) that will increase the predictability and stability of traffic flows, support a common operational picture through the use of digital data sharing, facilitate more effective collaborative decision making between airspace users and air navigation service providers, and enable increased levels of integrated automation across the NAS. The National Aeronautics and Space Administration (NASA) has been developing trajectory-based systems to improve the efficiency of the NAS during specific phases of flight and is now also exploring Advanced 4-Dimensional Trajectory (4DT) operational concepts that will integrate these technologies and incorporate new technology where needed to create both automation and procedures to support gate-to-gate TBO. A TBO Prototype simulation toolkit has been developed that demonstrates initial functionality that may reside in an Advanced 4DT TBO concept. Pilot and controller subject matter experts (SMEs) were brought to the Air Traffic Operations Laboratory at NASA Langley Research Center for discussions on an Advanced 4DT operational concept and were provided an interactive demonstration of the TBO Prototype using four example scenarios. The SMEs provided feedback on potential operational, technological, and procedural opportunities and concerns. After viewing the interactive demonstration scenarios, the SMEs felt the operational capabilities demonstrated would be useful for performing TBO while maintaining situation awareness and low mental workload. The TBO concept demonstrated produced defined routings around weather which resulted in a more organized, consistent flow of traffic where it was clear to both the controller and pilot what route the aircraft was to follow. In general, the controller SMEs felt that traffic flow management should be responsible for generating and negotiating the operational constraints demonstrated, in cooperation with the Air Traffic Control System Command Center, while air traffic control should be responsible for the implementation of those constraints. The SMEs also indicated that digital data communications would be very beneficial for TBO operations and would result in less workload due to reduced communications, would eliminate issues due to language barriers and frequency problems, and would make receiving, loading, accepting, and executing clearances easier, less ambiguous, and more expeditious. This paper describes an Advanced 4DT operational concept, the TBO Prototype, the demonstration scenarios and methods used, and the feedback obtained from the pilot and controller SMEs in this focus group evaluation.
ISO-26262, the road vehicle functional safety standard, underwent a major overhaul that was released in December 2018. Radiation effects, and single-event effect (SEE) hazards in particular, play an important role in autonomous vehicle safety. This connection will only increase as the level of driving automation goes from "hands off," to "eyes off," to "mind off." This translates to increased coupling with space climate and weather in addition to other traditional terrestrial radiation sources like thorium and uranium contamination in process and packaging materials. We will focus on autonomous vehicle radiation effects and present both benefits and challenges to the space weather and radiation engineering communities.
There are two sources of inaccuracy when simulating parallel and distributed computing systems: (i) a simulator implemented at an insufficient level of detail; and (ii) incorrectly calibrated simulation parameter values. Increasing the simulator’s level of detail can improve accuracy, but at the cost of higher space, time, and/or software complexity. Furthermore, evaluating the intrinsic accuracy of a simulator requires that its parameters be well-calibrated. Making decisions regarding the level of detail is thus challenging. We propose a methodology for instantiating the simulation calibration process and a framework for automating this process, which makes it possible to pick appropriate levels of detail for any simulator. We demonstrate the usefulness of our approach via two case studies for two different domains.
Advanced air mobility (AAM) technologies incorporate increasingly autonomous systems that allow fully remote, independent, and intelligent operation of air vehicles to support the transportation of goods and passengers within and across urban and rural areas. With a myriad of automated technologies enabling the AAM ecosystem, the human operator’s role will likely be a passive supervisory monitor of the air vehicles, involving increasingly fewer humans (m) that manage many more autonomous systems (N), or m:N operations. Unfortunately, the human performance literature suggests that human operators will exhibit poor supervision of numerous autonomous agents due to the limits of attentional resources in the operators. In the general human information-processing model, a human operator exercises a limited pool of attentional resources to engage various information-processing stages including detecting, perceiving, comprehending, and predicting objects around them. Yamani and Horrey (2018) expanded the human information-processing model to characterize a tradeoff between information-processing demand and resource relief that automation brings in the context of automated driving. In their model, a driver interacting with an automated driving system is assumed to reallocate resources “freed” by automation to support other information-processing stages required for successful task performance. A future AAM ecosystem enabled by an orchestration of advanced automated systems, however, requires a single operator to interact with more than one air vehicle with varying levels and degrees of automated systems, making the traditional framework of human-automation interaction insufficient. To address this gap, we provide a review of the literature on situation assessment and trust, two constructs identified as critical for a fuller understanding of intimate and intricate interactions between a human operator and multiple air vehicles equipped with increasingly autonomous systems. Then, we propose an expansion of Yamani and Horrey’s (2018) model to motivate systematic research on the human operator’s role, identify factors that influence resource allocation and guide human-centered design of an interface supporting the m:N operation in the AAM environment.
The Space Human Factors Engineering (SHFE) Standing Review Panel (SRP) evaluated 22 gaps and 39 tasks in the three risk areas assigned to the SHFE Project. The area where tasks were best designed to close the gaps and the fewest gaps were left out was the Risk of Reduced Safety and Efficiency dire to Inadequate Design of Vehicle, Environment, Tools or Equipment. The areas where there were more issues with gaps and tasks, including poor or inadequate fit of tasks to gaps and missing gaps, were Risk of Errors due to Poor Task Design and Risk of Error due to Inadequate Information. One risk, the Risk of Errors due to Inappropriate Levels of Trust in Automation, should be added. If astronauts trust automation too much in areas where it should not be trusted, but rather tempered with human judgment and decision making, they will incur errors. Conversely, if they do not trust automation when it should be trusted, as in cases where it can sense aspects of the environment such as radiation levels or distances in space, they will also incur errors. This will be a larger risk when astronauts are less able to rely on human mission control experts and are out of touch, far away, and on their own. The SRP also identified 11 new gaps and five new tasks. Although the SRP had an extremely large quantity of reading material prior to and during the meeting, we still did not feel we had an overview of the activities and tasks the astronauts would be performing in exploration missions. Without a detailed task analysis and taxonomy of activities the humans would be engaged in, we felt it was impossible to know whether the gaps and tasks were really sufficient to insure human safety, performance, and comfort in the exploration missions. The SRP had difficulty evaluating many of the gaps and tasks that were not as quantitative as those related to concrete physical danger such as excessive noise and vibration. Often the research tasks for cognitive risks that accompany poor task or information design addressed only part, but not all, of the gaps they were programmed to fill. In fact the tasks outlined will not close the gap but only scratch the surface in many cases. In other cases, the gap was written too broadly, and really should be restated in a more constrained way that can be addressed by a well-organized and complementary set of tasks. In many cases, the research results should be turned into guidelines for design. However, it was not clear whether the researchers or another group would construct and deliver these guidelines.
The Joint Planning and Development Office has proposed the introduction of automated systems to help air traffic controllers handle the increasing volume of air traffic in the next two decades (JPDO, 2007). Because fully automated systems leave operators out of the decision-making loop (e.g., Billings, 1991), it is important to determine the right level and type of automation that will keep air traffic controllers in the loop. This study examined the differences in the situation awareness (SA) and collision detection performance of individuals when they worked with information acquisition, information analysis, decision and action selection and action implementation automation to control air traffic (Parasuraman, Sheridan, & Wickens, 2000). When the automation was unreliable, the time taken to detect an upcoming collision was significantly longer for all the automation types compared with the information acquisition automation. This poor performance following automation failure was mediated by SA, with lower SA yielding poor performance. Thus, the costs associated with automation failure are greater when automation is applied to higher order stages of information processing. Results have practical implications for automation design and development of SA training programs.
The clean energy transformation includes the integration of distributed energy resources with the power grid, which has led to a substantial increase in the complexity of power grids infrastructure and the underlying operational technology environment. Power grids infrastructure represents an operational technology environment that has become a system of systems, integrating heterogeneous devices which are both software-and hardware-intensive; as a result, there are increasing demands to exploit advances in the commodity of software-hardware infrastructures to improve energy systems requirements such as cybersecurity and resilience. In such a setting, system requirements at different levels mix, which leads to vulnerabilities and undesirable outcomes. The use of formal methods to characterize and prove system requirements removes ambiguity, increases automation, and provides high levels of assurance and reliability. In this paper, we contribute a methodology and a framework for the system-level verification of zero trust architecture requirements in operational technology environments. We define a formal specification for the core functionalities of operational technology environments, the corresponding invariants, and security proofs. Of particular note is our modular approach for the formal verification of asynchronous interactions in operational technology environments. The formal specification and the proofs have been mechanized using the interactive theorem proving environment Isabelle/HOL.
The problem of providing an appropriate method by which a human pilot interacts with an automated nap-of-the-earth rotorcraft guidance and control system is addressed. This problem is closely related to the broader question of what level and degree of automation is effective at reducing pilot workload during low-altitude flight missions requiring obstacle avoidance. A systematic approach for establishing the possible combinations of manual vs automatic authority over relevant guidance and control functions is first presented. From these possibilities, three candidate concepts are selected based upon their potential for practical implementation and reduction in pilot workload. This paper describes the selection of these three pilot-interaction concepts and the mathematical models for their implementation.
The problem of providing an appropriate method by which a human pilot interacts with an automated nap-of-the-Earth rotorcraft guidance and control system is addressed. This problem is closely related to the broader question of what level and degree of automation is effective at reducing pilot workload during low-altitude flight missions requiring obstacle avoidance. A systematic approach for establishing the possible combinations of manual versus automatic authority over relevant guidance and control functions is first presented. From these possibilities, three candidate concepts are selected; selection is based upon their potential for practical implementation and reduction in pilot workload. This paper describes the selection of these three pilot-interaction concepts and the mathematical models for their implementation.
Adaptive automation refers to technology that can change its mode of operation dynamically. Further, both the technology and the operator can initiate changes in the level or mode of automation. The present paper reviews research on adaptive technology. It is divided into three primary sections. In the first section, issues surrounding the development and implementation of adaptive automation are presented. Because physiological-based measures show much promise for implementing adaptive automation, the second section is devoted to examining candidate indices. In the final section, those techniques that show the greatest promise for adaptive automation as well as issues that still need to be resolved are discussed.
This paper describes the Automated Scheduling and Planning Environment (ASPEN). ASPEN encodes complex spacecraft knowledge of operability constraints, flight rules, spacecraft hardware, science experiments and operations procedures to allow for automated generation of low level spacecraft sequences.