Search NASA⌕ Search

SEARCH · Search NASA

Results for “Localization Techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Sand Shear Band Thickness Measurements by Digital Imaging Techniques

Digital imaging analysis was used to study localized deformations in granular materials tested under plane strain condition. Two independent techniques were applied and compared. In the first, the digitized optical images of a grid printed on the latex membrane were used to measure the shear band orientation angle and thickness, and were found to be 54.5' and 3.01 mm respectively. The second technique involved introducing an ultra-low viscosity resin into the specimen in preparation for thin- sectioning and microscopic study of the internal fabric. A total of 24 microscopic images obtained from four thin sections were analyzed and void ratio variation was measured. The shear band thickness measurements from images located along the shear band axis (at two locations) were equal to 3.19 mm and 3.29 mm which are very close to the average value obtained from surface analysis. The study was then extended to investigate the effects of sand grain-size and properties, specimen density, and confining pressure on shear band thickness. It was found that the normalized shear band thickness decreases as grain-size and confining pressure increase and as density decreases. Finally, shear band thickness is highly influenced by the specimen dilatancy.

Alshibli, Khalid A.↗
NASA NTRS1985

Least squares collocation applied to local gravimetric solutions from satellite gravity gradiometry data

An autonomous spaceborne gravity gradiometer mission is being considered as a post Geopotential Research Mission project. The introduction of satellite diometry data to geodesy is expected to improve solid earth gravity models. The possibility of utilizing gradiometer data for the determination of pertinent gravimetric quantities on a local basis is explored. The analytical technique of least squares collocation is investigated for its usefulness in local solutions of this type. It is assumed, in the error analysis, that the vertical gravity gradient component of the gradient tensor is used as the raw data signal from which the corresponding reference gradients are removed to create the centered observations required in the collocation solution. The reference gradients are computed from a high degree and order geopotential model. The solution can be made in terms of mean or point gravity anomalies, height anomalies, or other useful gravimetric quantities depending on the choice of covariance types. Selected for this study were 30 x 30 foot mean gravity and height anomalies. Existing software and new software are utilized to implement the collocation technique. It was determined that satellite gradiometry data at an altitude of 200 km can be used successfully for the determination of 30 x 30 foot mean gravity anomalies to an accuracy of 9.2 mgal from this algorithm. It is shown that the resulting accuracy estimates are sensitive to gravity model coefficient uncertainties, data reduction assumptions and satellite mission parameters.

Robbins, J. W.↗
NASA NTRS2001

Localization of needle tip with color doppler during pericardiocentesis: In vitro validation and initial clinical application

This study evaluates a new device that uses color Doppler ultrasonography to enable real-time image guidance of the aspirating needle, which has not been possible until now. The ColorMark device (EchoCath Inc, Princeton, NJ) induces high-frequency, low-amplitude vibrations in the needle to enable localization with color Doppler. We studied this technique in 25 consecutive patients undergoing pericardiocentesis, and in vitro, in a urethane phantom with which the accuracy of color Doppler localization of the needle tip was compared with that obtained by direct measurement. Tip localization was excellent in vitro; errors axial to the ultrasound beam (velocity Doppler -0.13 +/- 0.90 mm, power Doppler -0.05 +/- 1.7 mm) were less than lateral errors (velocity -0.36 +/- 1.8 mm, power -0.02 +/- 2.8 mm). In 18 of 25 patients, the needle was identified and guided into the pericardial space with the ColorMark technique, and it allowed successful, uncomplicated drainage of fluid. Initial failures were the result of incorrect settings on the echocardiographic machine and inappropriate combinations of the needle puncture site and imaging window. This study demonstrates a novel color Doppler technique that is highly accurate at localizing a needle tip. The technique is feasible for guiding pericardiocentesis. Further clinical validation of this technique is required.

NASA Discipline Cardiopulmonary↗
NASA NTRS1984

On the utilization of engineering knowledge in design optimization

Some current research work conducted at the University of Michigan is described to illustrate efforts for incorporating knowledge in optimization in a nontraditional way. The incorporation of available knowledge in a logic structure is examined in two circumstances. The first examines the possibility of introducing global design information in a local active set strategy implemented during the iterations of projection-type algorithms for nonlinearly constrained problems. The technique used algorithms for nonlinearly constrained problems. The technique used combines global and local monotinicity analysis of the objective and constraint functions. The second examines a knowledge-based program which aids the user to create condigurations that are most desirable from the manufacturing assembly viewpoint. The data bank used is the classification scheme suggested by Boothroyd. The important aspect of this program is that it is an aid for synthesis intended for use in the design concept phase in a way similar to the so-called idea-triggers in creativity-enhancement techniques like brain-storming. The idea generation, however, is not random but it is driven by the goal of achieving the best acceptable configuration.

Papalambros, P.↗
NASA NTRSDate not supplied

Global-to-local air quality forecasts using the NASA GEOS Composition Forecast System

Since 2019, the NASA Global Earth Observing System (GEOS) model has been used to generate global, near-real-time estimates and daily five-day forecasts of atmospheric composition at a horizontal resolution of 0.25 degrees (~25 km) from the surface up to the lower mesosphere. This composition forecast system (“GEOS-CF”) combines the GEOS weather forecasting model with the state-of-the-science GEOS-Chem chemistry module to deliver detailed analysis of a wide range of air pollutants, including the policy-relevant species such as ozone, carbon monoxide, nitrogen oxides, sulfur dioxide and fine particulate matter (PM2.5). Because GEOS-CF includes atmospheric levels up through the stratosphere, this system has been leveraged to support the Tropospheric Emissions: Monitoring of Pollution (TEMPO) satellite mission and provide stratospheric intrusion alerts to ground-based monitoring stations. We will present recent advances to GEOS-CF which target increased computational efficiency and accuracy. These include the incorporation of simplified chemistry mechanisms to accelerate model forecasts, use of model-observation data fusion techniques to provide highly localized forecasts, and assimilation of satellite observations to produce more accurate model analyses. We further discuss our attempts to make these tools publicly available on platforms outside the NASA domain, such as Google Earth Engine and Amazon Web Services with the goal to facilitate the integration of state-of-the-science air quality information onto platforms used by stakeholders, air quality managers, and the public.

Emma Knowland↗
NASA NTRS2022

Galaxy Correlation Function and Local Density from Photometric Redshifts Using the Stochastic Order Redshift Technique (SORT)

The stochastic order redshift technique (SORT) is a simple, efficient, and robust method to improve cosmological redshift measurements. The method relies upon having a small (∼10 per cent) reference sample of high-quality redshifts. Within pencil- beam-like sub-volumes surrounding each galaxy, we use the precise dN/dz distribution of the reference sample to recover new redshifts and assign them one-to-one to galaxies such that the original rank order of redshifts is preserved. Preserving the rank order is motivated by the fact that random variables drawn from Gaussian probability density functions with different means but equal standard deviations satisfy stochastic ordering. This process is repeated for sub-volumes surrounding each galaxy in the survey. This results in every galaxy being assigned multiple ‘recovered’ redshifts from which a new redshift estimate is determined. An earlier paper applied SORT to a mock Sloan Digital Sky Survey at z 0.2 and accurately recovered the two-point correlation function (2PCF) on scales > 4 h−1Mpc. In this paper, we test the performance of SORT in surveys spanning the redshift range 0.75 < z < 2.25. We used two mock surveys extracted from the Small MultiDark–Planck and Bolshoi–Planck N-body simulations with dark matter haloes that were populated by the Santa Cruz semi-analytic model. We find that SORT overall improves redshift estimates, accurately recovers the redshift-space 2PCF ξ (s) on scales > 2.5 h−1Mpc, and provides improved local density estimates in regions of average or higher density, which may allow for improved understanding of how galaxy properties relate to their environments.

James Kakos↗
NASA NTRS1972

Metallic positive expulsion diaphragms

High-cycle life ring-reinforced hemispherical type positive expulsion diaphragm performance was demonstrated by room temperature fluid expulsion tests of 13" diameter, 8 mil thick stainless steel configurations. A maximum of eleven (11) leak-free, fluid expulsions were achieved by a 25 deg cone angle diaphragm hoop-reinforced with .110-inch cross-sectional diameter wires. This represents a 70% improvement in diaphragm reversal cycle life compared to results previously obtained. The reversal tests confirmed analytic predictions for diaphragm cycle life increases due to increasing values of diaphragm cone angle, radius to thickness ratio and material strain to necking capacity. Practical fabrication techniques were demonstrated for forming close-tolerance, thin corrugated shells and for obtaining closely controlled reinforcing ring stiffness required to maximize diaphragm cycle life. A non-destructive inspection technique for monitoring large local shell bending strains was developed.

Gleich, D.↗
NASA NTRS1974

Earth Observatory Satellite system definition study. Report no. 7: EOS system definition report. Appendixes A through D

An analysis of the systems involved in the operation and support of the Earth Observatory Satellite (EOS) is presented. Among the systems considered are the following: (1) the data management system, (2) observatory to primary ground station communications links, (3) local user system, (4) techniques for recognizing ground control points, (5) the central data processing-implementation concept, and (6) program effectiveness analysis.

Source record↗
NASA NTRS1975

The influence of crack closure and elasto-plastic flow on the bending of a cracked plate

The influence of crack closure and elastoplastic flow on the bending behavior of thin cracked plates is investigated using an incremental elastoplastic plate bending finite element computer program. The finite element program was developed using assumptions consistent with Kirchhoff fourth-order plate theory while the material property treatment permits general isotropic work hardening with local elastic unloading. This technique is applied to the problem of a large centrally through cracked plate subject to remote circular bending. Comparison is drawn between two cases of the bending problem. The first neglects the possibility of crack face interference with bending, and the second includes a kinematic prohibition against the crack face from passing through the symmetry plane. Results are reported which isolate the effects of elastoplastic flow and crack closure.

Jones, D. P.↗
NASA NTRS1980

Planetary observations with the Tidbinbilla interferometer

Radio observations at a wavelength of 13.1 cm of Saturn and Uranus made with the Tidbinbilla interferometer during 1978 and 1979 are summarized. The observations were made with 64-m and 26-m antennas on a 200-m north-south baseline at a bandwidth of 12 MHz with RCP polarization and a primary beamwidth of about 12 arcmin. A flux density of 198 + or - 15 mJy was measured for Saturn, which indicates a surface temperature, corrected for the occulting effect of the rings, of 191 + or - 15 K, in excellent agreement with previous determinations. With the use of a background subtraction technique to remove the local background confusion, Uranus was found to have a flux density of 11.7 + or - 0.8 mJy, indicating a disk-averaged brightness temperature of 255 + or - 18 K. The increase in Uranus brightness temperature over that measured 15 years previously is attributed to variations in temperature or opacity below the cloud tops, or to a reduction in relative ammonia abundance most likely reflecting a change in the aspect of the planet as viewed from earth.

Batty, M. J.↗
NASA NTRS1980

Physical and dynamical conditions in interstellar clouds

Techniques for measuring the local and global parameters that describe molecular clouds are presented and illustrated by selected results. The local parameters which characterize a given location in a cloud are gas kinetic temperature, dust temperature, total density, magnetic field strength, abundance of species i, volume cooling and heating rates for gas and dust, and the thermal and turbulent velocities. Global properties which characterize the cloud as a whole include the size expressed as a length or area, the orientation and shape, the mass, and the integrated heating and cooling rates. If the cloud as a whole is collapsing or rotating, then the collapse velocity and the rotational velocity or angular momentum are global properties. An intermediate class of parameters which shares features of local and global properties includes the column density of species i, the total column density, and the average density.

Evans, N. J., II↗
NASA NTRS1982

The effect of grooves in amorphous substrates on the orientation of metal deposits. I - Carbon substrates

The graphoepitaxial alignment of vapor-deposited discrete metal crystallites is investigated in the nucleation and growth stages and during annealing by in situ UHV/TEM techniques. Various stages of nucleation, growth and coalescence of vapor deposits of Au, Ag, Pb, Sn, and Bi on amorphous, topographically structured C substrates are analyzed by advanced dark-field techniques to detect preferred local orientations. It is found that the topography-induced orientation of metal crystallites depends strongly on their mobility and their respective tendency to develop pronounced crystallographic shapes. Lowering of the average surface free energies and increasing the crystallographic surface energy anisotropies cause generally improved graphoepitaxial alignments.

Anton, R.↗
NASA NTRS1983

Use of the VAS for analysis of a prethunderstorm environment

The information content of the VAS radiances can be converted to meteorological parameters useful for analyzing a severe weather environment. The method by which the VAS variances are converted to vertical profiles of temperature, dewpoints, and equivalent potential temperature involves a basic regression technique using the most local radiosonde data available for establishing a correlation matrix. The results indicate that mesoscale features apparent within images of the radiances can be converted to usable temperature and moisture fields using regression when surface temperature and dewpoint observations are included within the total data base. In addition, results indicate that surface data are very important for better defining lower tropospheric structure that the VAS radiances alone cannot properly resolve. Analyses of these retrievals distinctly show mesoscale structure in the temperature and moisture fields derived with VAS radiances collected every 3 hours, and 0000 GMT. The retrievals capture the moisture structure. More important, convective instability is clearly detected immediately before the onset of convection. The results indicate that the VAS is capable of providing valuable mesoscale information suitable for analyzing a preconvective environment that is generally clear.

Uccellini, L. W.↗
NASA NTRS1991

Sensitivity analysis of a wing aeroelastic response

A variation of Sobieski's Global Sensitivity Equations (GSE) approach is implemented to obtain the sensitivity of the static aeroelastic response of a three-dimensional wing model. The formulation is quite general and accepts any aerodynamics and structural analysis capability. An interface code is written to convert one analysis's output to the other's input, and visa versa. Local sensitivity derivatives are calculated by either analytic methods or finite difference techniques. A program to combine the local sensitivities, such as the sensitivity of the stiffness matrix or the aerodynamic kernel matrix, into global sensitivity derivatives is developed. The aerodynamic analysis package FAST, using a lifting surface theory, and a structural package, ELAPS, implementing Giles' equivalent plate model are used.

Kapania, Rakesh K.↗
NASA NTRS1991

On magnetothermal instability in cluster cooling flows

Lagrangian techniques appropriate to a local calculation are used to show that a weak ordered magnetic field can result in a generic condensational mode in cluster cooling flows. However, thermal instability appears possible only if the conductivity is well below its Spitzer value, for all nonradial wavenumbers. Wavenumbers not subject to conductive damping are subject to buoyant oscillations. It is shown that when instability is present, lateral magnetic confinement of high thermal pressure regions in the plasma by radial magnetic field lines is responsible in at least equal measure with radially directed magnetic tension for the suppression of oscillations and the reappearance of local condensational modes. The general importance of even very modest magnetic fields for destabilizing thermal time scale perturbations is emphasized.

Balbus, Steven A.↗
NASA NTRS1991

Development of an Accelerated Test Method for the Determination of Susceptibility to Atmospheric Corrosion

The theoretical rationale is presented for use of a repetitive cyclic current reversal voltammetric technique for characterization of localized corrosion processes, including atmospheric corrosion. Applicability of this proposed experimental protocol is applied to characterization of susceptibility to crevice and pitting corrosion, atmospheric corrosion and stress corrosion cracking. Criteria upon which relative susceptibility is based were determined and tested using two iron based alloys commonly in use at NASA-Kennedy; A36 (a low carbon steel) and 4130 (a low alloy steel). Practicality of the procedure was demonstrated by measuring changes in anodic polarization behavior during high frequency current reversal cycles of 25 cycles per second with 1 mA/sq cm current density amplitude in solutions containing Cl anions. The results demonstrated that, due to excessive polarization which affects conductivity of barrier corrosion product layers, A36 was less resistant to atmospheric corrosion than its 4130 counterpart; behavior which was also demonstrated during exposure tests.

Ambrose, John R.↗
NASA NTRS1993

Advanced adaptive computational methods for Navier-Stokes simulations in rotorcraft aerodynamics

A phase 2 research and development effort was conducted in area transonic, compressible, inviscid flows with an ultimate goal of numerically modeling complex flows inherent in advanced helicopter blade designs. The algorithms and methodologies therefore are classified as adaptive methods, which are error estimation techniques for approximating the local numerical error, and automatically refine or unrefine the mesh so as to deliver a given level of accuracy. The result is a scheme which attempts to produce the best possible results with the least number of grid points, degrees of freedom, and operations. These types of schemes automatically locate and resolve shocks, shear layers, and other flow details to an accuracy level specified by the user of the code. The phase 1 work involved a feasibility study of h-adaptive methods for steady viscous flows, with emphasis on accurate simulation of vortex initiation, migration, and interaction. Phase 2 effort focused on extending these algorithms and methodologies to a three-dimensional topology.

Stowers, S. T.↗
NASA NTRS1991

Long discontinuous fiber composite structure: Forming and structural mechanics

Cost effective composite structure has motivated the investigation of several new approaches to develop composite structure from innovative material forms. Among the promising new approaches is the conversion of planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. In the present study, the authors have established a framework which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. The initial study focuses upon the establishment of micromechanics models for prediction of the effective anisotropic viscosities of the oriented fiber assembly in a viscous matrix. Next, the developed constitutive relation is employed through an analogy with incompressible elasticity to exercise the finite element technique for determination of local fiber orientation and laminate thickness after forming. Results are presented for the stretch bending of a curved beam from an arbitrary composite laminate and the bulging of a clamped sheet. Structural analyses are conducted to determine the effect of microstructure on the performance of curved beams manufactured from long discontinuous fiber composites. For the purposes of this study, several curved beams with ideal and non-ideal microstructures are compared for response under pure bending. Material parameters are determined from a separate microstructural analysis.

Pipes, R. B.↗