Search NASA⌕ Search

SEARCH · Search NASA

Results for “MATERIALS - TEMPERATURES, HIGH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

High-intensity sound in air saturated fibrous bulk porous materials

The interaction high-intensity sound with bulk porous materials in porous materials including Kevlar 29 is reported. The nonlinear behavior of the materials was described by dc flow resistivity tests. Then acoustic propagation and reflection were measured and small signal broadband measurements of phase speed and attenuation were carried out. High-intensity tests were made with 1, 2, and 3 kHz tone bursts to measure harmonic generation and extra attenuation of the fundamental. Small signal standing wave tests measured impedence between 0.1 and 3.5 kHz. High level tests with single cycle tone bursts at 1 to 4 kHz show that impedance increases with intensity. A theoretical analysis is presented for high-porosity, rigid-frame, isothermal materials. One dimensional equations of motion are derived and solved by perturbation. The experiments show that there is excess attenuation of the fundamental component and in some cases a close approach to saturation. A separate theoretical model, developed to explain the excess attenuation, yields predictions that are in good agreement with the measurements. Impedance and attenuation at high intensities are modeled.

Kuntz, H. L., II↗
NASA NTRS1982

Silicon slicing by fixed abrasive slicing technique

One of the major cost factors in silicon ingot technology adaptation for terrestrial photovoltaic application is in slicing boules into wafers. The most developed industrial practice is the Internal Diameter (ID) slicing. This method utilizes diamond cutting. The diamond stands up for long periods, hence, the cost of expendable materials is low. However, the ID technology as practiced today has poor material utilization. The Multiblade Slurry (MBS) method has low equipment and labor costs but its expendable material costs are high. Recently Multiwire Slurry (MWS) technology has shown very good material utilization, but its expendable material costs are even higher than MBS. The multiwire Fixed Abrasive Slicing Technique (FAST) still in advanced development stage, combines the low expendable material costs of ID method, the low labor and equipment costs of MBS and high material utilization of MWS.

Schmid, F.↗
NASA NTRS1983

Low-Weight Inserts for Aluminum Honeycomb Panels

Fiber/epoxy composites used in place of solid aluminum. New proposal suggests to make inserts out of such lightweight, high strength materials as fiber/epoxy composites or high density aluminum honeycomb. Composite insert is same size and shape as aluminum insert it replaces.

Bumgarner, G. S.↗
NASA NTRS1983

Analysis of the stress state in an Iosipescu sheartest specimen

The state of stress in an Iosipescu shear test specimen is analyzed, utilizing a finite element computer program. The influence of test fixture configuration on this stress state is included. Variations of the standard specimen configuration, including notch depth, notch angle, and notch root radius are modeled. The purpose is to establish guidelines for a specimen geometry which will accommodate highly orthotropic materials while minimizing stress distribution nonuniformities. Materials ranging from isotropic to highly orthotropic are considered. An optimum specimen configuration is suggested, along with changes in the test fixture.

Walrath, D. E.↗
NASA NTRS1996

Investigation Into Radiation-Induced Compaction of Zerodur (trademark)

Zerodur is a low coefficient of thermal expansion glass-ceramic material. This property makes Zerodur an excellent material for high precision optical substrates. Functioning as a high precision optical substrate, a material must be dimensionally stable in the system operating environment. Published data indicate that Zerodur is dimensionally unstable when exposed to large doses of ionizing radiation. The dimensional instability is discussed as an increase in Zerodur density. This increase in density is described as a compaction. Experimental data showing proton-induced compaction of Zerodur is presented. The dependence of compaction on proton dose was determined to be a power law relationship.

Edwards, D. L.↗
NASA NTRS1996

Sol-gel Technology and Advanced Electrochemical Energy Storage Materials

Advanced materials play an important role in the development of electrochemical energy devices such as batteries, fuel cells, and electrochemical capacitors. The sol-gel process is a versatile solution for use in the fabrication of ceramic materials with tailored stoichiometry, microstructure, and properties. This processing technique is particularly useful in producing porous materials with high surface area and low density, two of the most desirable characteristics for electrode materials. In addition,the porous surface of gels can be modified chemically to create tailored surface properties, and inorganic/organic micro-composites can be prepared for improved material performance device fabrication. Applications of several sol-gel derived electrode materials in different energy storage devices are illustrated in this paper. V2O5 gels are shown to be a promising cathode material for solid state lithium batteries. Carbon aerogels, amorphous RuO2 gels and sol-gel derived hafnium compounds have been studied as electrode materials for high energy density and high power density electrochemical capacitors.

Chung-tse Chu↗
NASA NTRS2015

Mechanical Components from Highly Recoverable, Low Apparent Modulus Materials

A material for use as a mechanical component is formed of a superelastic intermetallic material having a low apparent modulus and a high hardness. The superelastic intermetallic material is conditioned to be dimensionally stable, devoid of any shape memory effect and have a stable superelastic response without irrecoverable deformation while exhibiting strains of at least 3%. The method of conditioning the superelastic intermetallic material is described. Another embodiment relates to lightweight materials known as ordered intermetallics that perform well in sliding wear applications using conventional liquid lubricants and are therefore suitable for resilient, high performance mechanical components such as gears and bearings.

Padula, Santo, II↗
NASA NTRS1975

Correlation of Al/Si X-ray fluorescence data with other remote sensing data from the Taurus-Littrow area

Al/Si intensity ratios from the Apollo 15 X-ray fluorescence experiment have been analyzed in conjunction with such other remote-sensing data as visible albedo measurements, color-difference photographs, and relative spectral reflectivity curves for the purpose of defining geochemical units in the Taurus-Littrow area. A geochemical boundary between the dark-mantle unit and the western edge of the Taurus Mountains is indicated by all the remote-sensing techniques considered. The major component of the ejecta from Catena Littrow, located within the dark-mantle unit, is highland-type material. The areal extent of the ejecta determined from the Al/Si data is at least 30 km along the Apollo 15 ground track. The constraint imposed upon depth to high-alumina material at Catena Littrow is 520 m. If the high-alumina material excavated at Catena Littrow is an extension of the Taurus Mountain 'roots', then the maximum slope of the buried highland surface from Catena Littrow to the Taurus Mountains border is less than 2.0 deg

Andre, C. G.↗
NASA NTRS1977

Mercurian bright patches - Evidence for physio-chemical alteration of surface material

Morphologically and photometrically anomalous patches of highly-reflective material exist inside several large Mercurian craters. Calculations assuming that the patches exhibit an average lunar photometric function yield normal albedos of .39-.45, roughly 60% higher than Aristarchus, the brightest feature on the moon. Color-ratio images derived from Mariner 10 imaging data indicate that bright patches are bluer than typical Mercurian surface material, and are surrounded by material redder than typical surface material. Local physio-chemical alteration along impact-induced fractures may have been involved in production of these uniquely Mercurian features.

Dzurisin, D.↗
NASA NTRS2007

Larger, Lighter Space Telescopes by Implementing In-Space Manufacturing Concepts

There is a continuous demand for larger, lighter, and higher quality telescopes from both the astronomical and global surveillance communities one looking up and the other down. Enabling technologies must be developed and implemented that will allow this goal to be financially and technically feasible. The optical systems needed far high spatial resolution surveillance and astronomical applications require large optical, apertures with mention of future systems up to 150 meter in diameter. With traditional optical manufacturing technologies, large optical aperture means high mass and long fabrication lead times with associated high costs. Completely new approaches to optical fabrication must be developed to enable the fabrication of such optical systems. The cost and lead time associated with the fabrication of lightweight, high quality optical systems limits the feasible size of the optics. A primary factor in the launch cost of space optical systems is volume and mass. To minimize the mass of the high quality optics, optical fabricators implement materials with high specific stiffness and use honeycomb, or other structural minimization patterns, to support the optical surface; however, the structure must still be designed to survive launch loads. This sigmficantly adds to the fabrication difficulty and dramatically increases launch costs. One approach to minimizing launch volume and negating the need for the design to survive launch loads is to send the manufacturing facility and raw materials into space and perform the fabrication in-situ. We, are currently performing feasibility studies of initial concepts for inspace manufacturing of optical systems. By utilizing the micro-gravity and vacuum environment of space while eliminating the constraints defined by high launch forces and limited volume of the launch vehicle, the development of large, high quality glass membrane mirrors may be feasible. Several concepts were investigated to address the manufacturing of both optical surfaces and telescope structure. We will describe one of the primary approaches to utilize the space environment for optical manufacturing and describe initial results.

Mooney, James t.↗
NASA NTRS1976

Ultraviolet absorption lines associated with the Vela supernova remnant

Two stars behind the Vela supernova remnant and two stars offset from the remnant have been observed with the UV spectrometer aboard the Copernicus satellite. Over 200 interstellar atomic and molecular absorption features between 1000 and 1400 A have been identified and measured for radial velocity and equivalent width. In many cases, additional information was obtained by studying the detailed shapes of the recorded profiles. Most of the stars show several absorption components, with clouds of the highest radial velocity appearing in the spectra of stars behind the remnant. For each component, column densities were derived using velocity dispersion parameters which yielded the most self-consistent results. Qualitatively, the gas toward the remnant exhibits a number of unusual properties, when compared with normal interstellar material. First, abnormally high radial velocities were evident. Second, the degree of ionization of some elements suggested the existence of ionizing processes significantly more potent than those found in general regions of space. Finally, an investigation of electron densities shows that much of the gas, especially that at high velocity, must exist in the form of relatively thin sheets or filaments. If cosmic abundances prevail, the column densities of high-velocity excited material suggest that H-alpha emission measures could be as large as 100 sq cm/cu pc.

Jenkins, E. B.↗
NASA NTRS1991

Mechanical property characterization and impact resistance of selected graphite/PEEK composite materials

To use graphite/PEEK material on highly curved surfaces requires that the material be drapable and easily conformable to the surface. The mechanical property characterization and impact resistance results are presented for laminates made from two types of graphite/PEEK materials that will conform to a curved surface. These laminates were made from two different material forms. These forms are: (1) a fabric where each yarn is a co-mingled Celion G30-500 3K graphite fiber and PEEK fiber; and (2) an interleaved material of Celion G30-500 3K graphite fiber interleaved with PEEK film. The experimental results from the fabric laminates are compared with results for laminates made from AS4/PEEK unidirectional tape. The results indicate that the tension and compression moduli for quasi-isotropic and orthotropic laminates made from fabric materials are at least 98 pct. of the modulus of equivalent laminates made from tape materials. The strength of fabric material laminates is at least 80 pct. of laminates made from tape material. The evaluation of the fabric material for shear stiffness indicates that a tape material laminate could be replaced by a fabric material laminate and still maintain 89 pct. of the shear stiffness of the tape material laminate.

Baker, Donald J.↗
NASA NTRS1994

Mechanical property characterization and impact resistance of selected graphite/PEEK composite materials

To use graphite polyetheretherketone (PEEK) material on highly curved surfaces requires that the material be drapable and easily conformable to the surface. This paper presents the mechanical property characterization and impact resistance results for laminates made from two types of graphite/PEEK materials that will conform to a curved surface. These laminates were made from two different material forms. These forms are: (1) a fabric where each yarn is a co-mingled Celion G30-500 3K graphite fiber and PEEK thermoplastic fiber; and (2) an interleaved material of Celion G30-500 3K graphite fabric interleaved with PEEK thermoplastic film. The experimental results from the fabric laminates are compared with results for laminates made from AS4/PEEK unidirectional tape. The results indicate that the tension and compression moduli for quasi-isotropic and orthotropic laminates made from fabric materials are at least 79 percent of the modulus of equivalent laminates made from tape material. The strength of fabric material laminates is at least 80 percent of laminates made from tape material. The evaluation of fabric material for shear stiffness indicates that a tape material laminate could be replaced by a fabric material laminate and still maintain 89 percent of the shear stiffness of the tape material laminate. The notched quasi-isotropic compression panel failure strength is 42 to 46 percent of the unnotched quasi-isotropic laminate strength. Damage area after impact with 20 ft-lbs of impact energy is larger for the co-mingled panels than for the interleaved panels. The inerleaved panels have less damage than panels made from tape material. Residual compression strength of quasi-isotropic panels after impact of 20 ft-lbs of energy varies between 33 percent of the undamaged quasi-isotropic material strength for the tape material and 38 percent of the undamaged quasi-isotropic material strength for the co-mingled fabric material.

Baker, Donald J.↗
NASA NTRS2000

Electroactive Polymers as Artificial Muscles: Capabilities, Potentials and Challenges

The low density and the relative ease of shaping made polymers highly attractive materials and they are increasingly being chosen for aerospace applications. Polymer matrix composite materials significantly impacted the construction of high performance aircraft components and structures. In recent years, the resilience characteristics of polymers made them attractive to the emerging field of inflatable structures. Balloons were used to cushion the deployment of the Mars Pathfinder lander on July 4, 1997, paving the way for the recent large number of related initiatives. Inflatable structures are now being used to construct a rover, aerial vehicles, telescopes, radar antennas, and others. Some of these applications have reached space flight experiments, whereas others are now at advanced stages of development.

Bar-Cohen, Yoseph↗
NASA NTRS1994

Material Properties for Fiber-Reinforced Silica Aerogels

Ceramic fiber-reinforced silica aerogels are novel materials for high performance insulation, including thermal protection materials. Experimental data are presented for the thermal and mechanical properties, showing the trends exhibited over a range of fiber loadings and silica aerogel densities. Test results are compared to that of unreinforced bulk aerogels.

White, Susan↗
NASA NTRS2002

Thermal Technology Development Activities at the Goddard Space Flight Center - 2001

This presentation provides an overview of thermal technology development activities carried out at NASA's Goddard Space Flight Center during 2001. Specific topics covered include: two-phase systems (heat pipes, capillary pumped loops, vapor compression systems and phase change materials), variable emittance systems, advanced coatings, high conductivity materials and electrohydrodynamic (EHD) thermal coatings. The application of these activities to specific space missions is also discussed.

Butler, Dan↗
NASA NTRS1993

The coherent backscattering opposition effect

We have measured the opposition effect, the nonlinear surge in reflectance seen in particulate materials as phase angle approaches zero degrees, in a suite of materials of varying particle size and reflectance. These samples were illuminated by linearly and circularly polarized monochromatic radiation at two wavelengths, 0.442 and 0.633 microns. By measuring the linear and circular polarization ratios for each sample, we have found that in highly reflective materials the behavior of the reflected radiation is consistent with the coherent backscattering process which has recently been proposed to explain the opposition surge that is seen in such media. The size and width of the coherent backscattering opposition peak vary as a function of reflectance of the sample. The opposition effect has been observed in particulate materials studied in the laboratory and it is also observed in the radiation reflected from solar system bodies which present a regolith to the earth based observer. The traditional explanation of the opposition effect, the shadow-hiding hypothesis, is that it was caused by the elimination of mutual shadows cast between the regolith grains as the phase angle of the observation became smaller. This shadow-hiding hypothesis, however, is unable to explain the opposition effect seen in highly reflective materials such as magnesium oxide and barium sulfate powders. This is because highly reflective media will multiply scatter the incident radiation between the regolith grains. This causes the shadows to be eliminated. We have measured the angular scattering properties of a suite of materials of different reflectivity. We have observed polarization ratios in reflective particulates that are consistent with coherent backscattering as the principal process which causes the opposition surge.

Nelson, R. M.↗