Search NASA⌕ Search

SEARCH · Search NASA

Results for “MODE SHAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Ground vibration testing of complex structures

A method of measuring separately the in-phase and quadrature components of the vibration response, designed by APL, was developed and applied. Both analysis and test results show immediately a much improved definition of mode shapes and frequencies. The approach was further developed. It allows the measurement of damping in the different natural modes, and the determination of the exact shape of the normal modes, i.e., to eliminate the coupling effect due to structural damping. It is also expected to be used in flight flutter testing.

Stahle, C. V.↗
NASA NTRS1973

Vibration characteristics of aluminum plates reinforced with boron-epoxy composite material.

Analytical and experimental data on the vibration characteristics of cantilevered winglike flat trapezoidal aluminum plates are presented. The plates had been reinforced with boron-epoxy composite material which had been placed symmetrically about the plate middle surface. The effect of filament orientation on the mode shapes and frequencies of the first ten modes and on the damping coefficients of several of the lowest frequency modes has been investigated experimentally. Experimental data are compared with results from a finite-element analysis. Stiffness properties of the composite material for use in the analysis were determined from vibration tests of composite reinforced aluminum beams.

Clary, R. R.↗
NASA NTRS1986

Test versus analysis: A discussion of methods

Some techniques for comparing structural vibration data determined from test and analysis are discussed. Orthogonality is a general category of one group, correlation is a second, synthesis is a third and matrix improvement is a fourth. Advantages and short-comings of the methods are explored with suggestions as to how they can complement one another. The purpose for comparing vibration data from test and analysis for a given structure is to find out whether each is representing the dynamic properties of the structure in the same way. Specifically, whether: mode shapes are alike; the frequencies of the modes are alike; modes appear in the same frequency sequence; and if they are not alike, how to judge which to believe.

Butler, T. G.↗
NASA NTRS1991

Sensitivity of Space Station alpha joint robust controller to structural modal parameter variations

The photovoltaic array sun tracking control system of Space Station Freedom is described. A synthesis procedure for determining optimized values of the design variables of the control system is developed using a constrained optimization technique. The synthesis is performed to provide a given level of stability margin, to achieve the most responsive tracking performance, and to meet other design requirements. Performance of the baseline design, which is synthesized using predicted structural characteristics, is discussed and the sensitivity of the stability margin is examined for variations of the frequencies, mode shapes and damping ratios of dominant structural modes. The design provides enough robustness to tolerate a sizeable error in the predicted modal parameters. A study was made of the sensitivity of performance indicators as the modal parameters of the dominant modes vary. The design variables are resynthesized for varying modal parameters in order to achieve the most responsive tracking performance while satisfying the design requirements. This procedure of reoptimization design parameters would be useful in improving the control system performance if accurate model data are provided.

Kumar, Renjith R.↗
NASA NTRS2011

Dampers for Stationary Labyrinth Seals

Vibration dampers have been invented that are incorporated as components within the stationary labyrinth seal assembly. These dampers are intended to supplement other vibration-suppressing features of labyrinth seals in order to reduce the incidence of high-cycle-fatigue failures, which have been known to occur in the severe vibratory environments of jet engines and turbopumps in which labyrinth seals are typically used. A vibration damper of this type includes several leaf springs and/or a number of metallic particles (shot) all held in an annular seal cavity by a retaining ring. The leaf springs are made of a spring steel alloy chosen, in conjunction with design parameters, to maintain sufficient preload to ensure effectiveness of damping at desired operating temperatures. The cavity is vented via a small radial gap between the retaining ring and seal housing. The damping mechanism is complex. In the case of leaf springs, the mechanism is mainly friction in the slippage between the seal housing and individual dampers. In the case of a damper that contains shot, the damping mechanism includes contributions from friction between individual particles, friction between particles and cavity walls, and dissipation of kinetic energy of impact. The basic concept of particle/shot vibration dampers has been published previously; what is new here is the use of such dampers to suppress traveling-wave vibrations in labyrinth seals. Damping effectiveness depends on many parameters, including, but not limited to, coefficient of friction, mode shape, and frequency and amplitude of vibrational modes. In tests, preloads of the order of 6 to 15 lb (2.72 to 6.8 kilograms) per spring damper were demonstrated to provide adequate damping levels. Effectiveness of shot damping of vibrations having amplitudes from 20 to 200 times normal terrestrial gravitational acceleration (196 to 1,960 meters per square second) and frequencies up to 12 kHz was demonstrated for shot sizes from 0.032 to 0.062 in. (0.8 to 1.6 millimeters) at fill levels of from 70 to 95 percent.

El-Aini, Yehia↗
NASA NTRSDate not supplied

Coherent Mode Decomposition for Kolmogorov Optical Turbulence in a Finite Aperture

An analysis of the coherent mode decomposition of an optical field after propagation through atmospheric turbulence is presented. The coherent modes represent an ideal basis by which to decompose the field for design of mode-limited optical systems. Using the rotational symmetry of the Fredholm integral operator for Kolmogorov optical turbulence, it is shown that the coherent modes exhibit separable solutions classified by radial and azimuthal quantum numbers. The study of the coherent modes is then reduced that of the radial functions determined by the aperture-coherence diameter ratio and obscuration ratio. Analysis of the spectrum of eigenvalues yields sharp bounds on the efficiency of receivers using incoherent or coherent combining with mode-limited photonic devices in the presence of Kolmogorov turbulence. The effective number of modes needed to represent Kolmogorov optical turbulence is studied via the von Neumann entropy, purity, and largest eigenvalue, and the differences in the different definitions is discussed. The similarity of the coherent modes to linearly polarized (LP) fiber modes is quantified yielding a precise characterization of the maximum gain that can be achieved in mode-limited systems via mode shaping techniques. As a final application, a mode sorting technique is presented for optimally splitting power from atmospherically degraded light into a finite number of modes simultaneously maximizing total coupling efficiency and minimizing the average and instantaneous power ratio between channels.

free-space optical communication↗
NASA NTRSDate not supplied

Coherent Mode Decomposition for Kolmogorov Optical Turbulence in a Finite Aperture

An analysis of the coherent mode decomposition of an optical field after propagation through atmospheric turbulence is presented. The coherent modes represent an ideal basis by which to decompose the field for design of mode-limited optical systems. Due to rotational symmetry of the Fredholm integral operator for Kolmogorov optical turbulence, the coherent modes exhibit separable solutions classified by a radial and azimuthal mode index. The study of the coherent modes is then reduced to that of the radial functions determined by the coherence ratio and obscuration ratio. Analysis of the spectrum of eigenvalues yields sharp bounds on the efficiency of receivers using incoherent or coherent combining with mode-limited photonic devices in the presence of Kolmogorov turbulence. The effective number of modes needed to represent Kolmogorov optical turbulence is studied via the von Neumann entropy, purity, and largest eigenvalue, and the differences in the different definitions is discussed. The similarity of the coherent modes to linearly polarized (LP) fiber modes is quantified yielding a precise characterization of the maximum gain that can be achieved in mode-limited systems via mode shaping techniques. As a final application, a mode sorting technique is presented for optimally splitting power from atmospherically degraded light into a finite number of modes simultaneously maximizing total coupling efficiency and minimizing the difference in average power between channels.

free-space optical communication↗
NASA NTRS1974

An experimental-theoretical study of free vibrations of plates on elastic point supports

A theoretical and experimental study is made to investigate the effect on plate vibrations of varying the stiffness of corner elastic point supports. An experiment is conducted in which the bending stiffness of horizontal beams is used to support a square plate at its four corners. The stiffness of these supports can be varied over such a range that the plate fundamental frequency is lowered to 40% of the rigid support frequency. The variation with support stiffness of the frequencies of the first eight plate modes is measured and is compared with results from a theoretical model in which a Rayleigh-Ritz analysis is used which approximates the plate mode shapes as products of free-free beam modes. The elastic point supports are modeled both as massless translational springs and springs with tip masses, which are included to better represent the experimental supports.

Leuner, T. R.↗
NASA NTRS1985

The dynamics and control of large flexible space structures, 8

A development of the in plane open loop rotational equations of motion for the proposed Spacecraft Control Laboratory Experiment (SCOLE) in orbit configuration is presented based on an Eulerian formulation. The mast is considered to be a flexible beam connected to the (rigid) shuttle and the reflector. Frequencies and mode shapes are obtained for the mast vibrational appendage modes (assumed to be decoupled) for different boundary conditions based on continuum approaches and also preliminary results are obtained using a finite element representation of the mast reflector system. The linearized rotational in plane equation is characterized by periodic coefficients and open loop system stability can be examined with an application of the Floquet theorem. Numerical results are presented to illustrate the potential instability associated with actuator time delays even for delays which represent only a small fraction of the natural period of oscillation of the modes contained in the open loop model of the system. When plant and measurement noise effects are added to the previously designed deterministic model of the hoop column system, it is seen that both the system transient and steady state performance are degraded. Mission requirements can be satisfied by appropriate assignment of cost function weighting elements and changes in the ratio of plant noise to measurement noise.

Bainum, P. M.↗
NASA NTRS2018

Jig-Shape Optimization of a Low-Boom Supersonic Aircraft

A simple approach for optimizing the jig-shape is proposed in this study. This simple approach is based on an unconstrained optimization problem and applied to a low-boom supersonic aircraft. In this study, the jig-shape optimization is performed using the two-step approach. First, starting design variables are computed using the least-squares surface fitting technique. Next, the jig-shape is further tuned using a numerical optimization procedure based on an in-house object-oriented optimization tool. During the numerical optimization procedure, a design jig-shape is determined by the baseline jig-shape and basis functions. A total of 12 symmetric mode shapes of the cruise-weight configuration, rigid pitch shape, rigid left and right stabilator rotation shapes, and a residual shape are selected as sixteen basis functions. After three optimization runs, the trim shape error distribution is improved, and the maximum trim shape error of 0.9844 inches of the starting configuration becomes 0.00367 inch by the end of the third optimization run.

numerical analysi↗