Search NASA⌕ Search

SEARCH · Search NASA

Results for “Manufactured Materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Scaling effects of defects in fiber-reinforced composites

Material defects may be introduced willingly or unwillingly during material manufacturing and structural component fabrication stages. Their presence in the material plays a dominant role in determining the material's strength and the associate failure mechanisms. In the sense that the size and the number of defects may increase with the volume of the material, the effect of dimensional scaling may manifest itself in the dependence of material strength on volume. Or, alternatively, there may exist a scaling effect of material defects. In fiber-reinforced composites, manufacturing or fabrication defects may come in several forms: matrix voids, matrix microcracks, fiber misalignment, broken fibers, or interface disbonds, just to mention a few. These are interacting and competing defects in the sense that one type of defect may become dominant under one stress condition and another type of defect may become dominant under a different stress condition. This happens because the fiber reinforcement network, together with the distribution of defects, constitutes the prime microstructure of the composite, and there exist continued interactions between the evolving microstructure and the distribution of defects. In the process, the scaling effects of defects are complicated by this interaction. In this presentation, the scaling effects of defects in fiber-reinforced composites will be briefly discussed with the introduction of the concept of effective defects. It is then shown with the aid of some actual experimental and analysis results that the scaling effects are very much present, but they are regulated by the characteristic dimension of the composite microstructure due to the aforementioned microstructure-defect interaction effect.

Wang, A. S. D.↗
DOE OSTI2023

Embracing Anisotropy – Opportunities and Challenges to the Functional Application of Advanced Manufacturing of Energetic Materials

The growing use of additive manufacturing (AM) to manipulate materials, such as metals and plastics, is a result of the desire to realize the potential benefits (i.e., cheaper, faster, and simpler production of complex parts) of the process and the efforts of countless researchers to reduce the method to practice for a broad range of materials. However, in the field of energetic materials (EMs), similar benefits have been broadly claimed, but the transition to practical, industrial applications is still not obvious. The translation of small-scale experimental results to real-world application will have unique challenges, especially due to the nature and requirements of EM functionality. Some of the benefits of AM, such as simpler and faster part creation, are more easily realized. However, attaining the most profound benefits, such as added functionality enabled by spatial gradations of composition or density, will require much more effort from the EMs community to put them into general use.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Techno-economic analysis of cathode material production using flame-assisted spray pyrolysis

The cost of cathode materials contributes approximately 32.7% of the total cell construction cost of lithium-ion batteries, significantly affecting the price of battery packs. To reduce the cathode material manufacturing cost, a flame-assisted spray pyrolysis (FSP) method has been developed to utilize a sustainable solvent of glycerol to manufacture the LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC333) cathode materials. The purpose of this study is to evaluate the minimum cathode material selling price (MCSP) of the FSP processes compared with a traditional carbonate co-precipitation pathway. Results show that the MCSP of the FSP is $\$$19.1/kg that is 17% lower than the traditional carbonate co-precipitation pathway as a result of lower fixed operating cost and variable overhead. Sensitivity analysis shows that when the new process is integrated with in-situ sintering and processing, the MCSP can be as low as $\$$15.6/kg. When all the material prices are decreased by 20%, the FSP process can synthesize NMC333 at a price of $\$$2.3/kg lower. According to the simulation result, LiNi 0·8 Mn 0·1 Co 0·1 O 2 (NMC811) has the best potential to meet the U.S. Department of Energy battery price target of $\$$125/kWh, demonstrating that the FSP process is an attractive manufacturing technology for NMC cathode powder material production.

25 ENERGY STORAGE↗
DOE OSTI2023

MDDC Multi-Length Scale Data Architecture Contribution Report – PNNL, INL, ANL, LANL and ORNL

This report offers a comprehensive view of data streams currently generated at Pacific Northwest National Laboratory, Idaho National Laboratory, Argonne National Laboratory, Los Alamos National Laboratory, and Oak Ridge National Laboratory set to integrate into the evolving Multi-Dimensional Data Correlation framework at Oak Ridge National Laboratory. Developed by the Advanced Materials and Manufacturing Technologies program, the Multi-Dimensional Data Correlation framework serves as a cutting-edge software to manage data relevant to advanced manufacturing and material behavior in advanced reactors. The report defines data streams, highlights their generation methods and visualization methods both for experimental and computational aspects relevant to the Advanced Materials and Manufacturing Technologies project. A logical next step for this work is to integrate the MDDC framework into PNNL’s, INL’s, ANL’s, LANL’s and ORNL’s fabrication, experimentation, and modelling workflows. This would require setting up the MDDC framework at PNNL, INL, ANL, and LANL and integrating it into the data collection and storage for these different activities.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Obtaining NASA Approval for use of Non-Metallic Materials in Manned Space Flight

Material manufacturers and suppliers are often surprised when a material commonly provided to industry is not approved for use on manned spacecraft. Often the reason is a lack of test data in environments that simulate those encountered in space applications, especially oxygen-enriched conditions, which significantly increase both the likelihood of material combustion and the propagation of a fire. This paper introduces the requirements for flight approval of non-metallic materials, focusing on material testing for human-rated space flight programs; it reviews the history of flight materials requirements and provides the rationale for such and introduces specific requirements related to testing and to good material engineering and design practices. After describing the procedure for submitting materials to be tested, the paper outlines options available if a material fails testing. In addition, this treatise introduces the National Aeronautics and Space Administration's (NASA's) Materials and Processes Technical Information System (MAPTIS), a database housing all test data produced in accordance with NASA-STD-6001, Flammability, Odor, Offgassing, and Compatibility Requirements and Test Procedures for Materials in Environments that Support Combustion.

Davis, Samuel E.↗
DOE OSTI2025

INL Creep Testing Capabilities

Motivation – Advanced Reactors Developing, emerging, and nascent advanced reactor technologies involve new materials, manufacturing methods Extreme operating conditions In some cases, material service life needs to be defined or reassessed

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Chemical and Radiological Compatibility Testing of 3D Printed Materials

To dramatically increase the adaptability, performance, and safety of processes in support of the Defense Waste Processing Facility (DWPF), Savannah River National Lab (SRNL) plans to perform chemical and radiological compatibility testing on a wide variety of 3D printed materials of interest. The 3D printing process provides numerous strategic operational benefits such as rapid prototyping of complex designs and geometry specific to the needs of the nuclear waste disposition process, as well as on-demand rapid prototyping and iteration with materials that aren’t as accessible through traditional manufacturing methods. Reaction chemistry in simulated waste batches can be matched closely to its radioactive counterpart, but glass reactor vessels have limitations. Vessel geometry can play a big factor in mixing transport limitations, process chemistry, and degradation reaction kinetics. In addition, additive manufacturing allows for much more detailed vessel design than traditional alternatives. Waste processing techniques in DWPF also encounter extreme chemical environments including high pH, strong acids, abrasive slurries, and significant irradiation. To meet these challenges, a matrix of various polymer, ceramic, and metal additive manufacturing materials have been exposed to a suite of chemical environments of interest as well as radioactive dose (such as gamma radiation from 60 Co) to properly test their durability under these conditions. Mass change has been monitored over a period of up to a week in these conditions, as well as added characterization for surface modification through Scanning Electron Microscopy/Electron Dispersive X-ray analysis (SEM/EDX). Further chemical characterization has been monitored through Fourier-Transform InfraRed Spectroscopy (FTIR), with planned investigation via thermal and tensile strength degradation. While the direct product of this research is identification of material(s) that can withstand specific hazardous environments encountered by the mercury water wash tank in DWPF process simulation experiments, the reference base of materials will be used for many other nuclear processes in the pursuit of rapidly developed, cost-efficient, and highly specific devices for environmental remediation and much more.

Wilson, Nathan W. [Savannah River National Laborat↗
NASA NTRS2016

Review of Potential Wind Tunnel Balance Technologies

This manuscript reviews design, manufacture, materials, sensors, and data acquisition technologies that may benefit wind tunnel balances for the aerospace research community. Current state-of-the-art practices are used as the benchmark to consider advancements driven by researcher and facility needs. Additive manufacturing is highlighted as a promising alternative technology to conventional fabrication and has the potential to reduce both the cost and time required to manufacture force balances. Material alternatives to maraging steels are reviewed. Sensor technologies including piezoresistive, piezoelectric, surface acoustic wave, and fiber optic are compared to traditional foil based gages to highlight unique opportunities and shared challenges for implementation in wind tunnel environments. Finally, data acquisition systems that could be integrated into force balances are highlighted as a way to simplify the user experience and improve data quality. In summary, a rank ordering is provided to support strategic investment in exploring the technologies reviewed in this manuscript.

Burns, Devin E.↗
DOE OSTI2022

Structural stability of thin overhanging walls during material extrusion additive manufacturing of thermoset-based ink

Recent developments have enabled material extrusion additive manufacturing of thermoset-based composite inks on the large scale. In addition, printing out-of-plane components is of broad interest to the polymer material extrusion community. Here, we address some of the challenges associated with both large-scale and out-of-plane thermoset material extrusion additive manufacturing by studying the height at which thin overhanging walls collapse. Walls at a range of overhang angles were printed until they collapsed. An optical camera captured the profile of each wall throughout the print, allowing the collapse height to be identified and the geometric fidelity to the programmed angle to be evaluated. Using previously measured rheological properties, predictive models were generated to approximate the collapse height and profile of the deflected walls. First, an analytical model was created to predict the height at which the walls would yield. The analytical model assumes the walls exhibit a perfectly linear profile; however, experiments proved this assumption to be false. Therefore, a finite element simulation was developed to account for the elastic deflection that occurs during printing. The finite element simulation predicts both the yield height and the deflected profile after the deposition of each layer. For the properties of the thermoset ink used here, the yield height predicted by the analytical model and finite element simulation are virtually identical. These predictions match experimental data reasonably well, but minor errors are observed. Accounting for the fully plastic moment appears to explain the small mismatch between experimental data and predictions. Additionally, the finite element simulation provides an excellent prediction of the deflected profile before the wall begins to collapse. Finally, by demonstrating that the collapse height and deflected profile of thin overhanging walls can be predicted, this work illustrates how the soft viscoelastic properties of thermoset-based composite inks limit the scale of a key feature required to print some nonplanar components. It also provides a basis to tailor in-process curing systems to suppress deflection and collapse of thin overhanging walls.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Fracture Control for Additively Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗
NASA NTRS2019

Fracture Control for Additive Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗
NASA NTRS1982

Constitutive model development for isotropic materials

The objective is to develop a unified constitutive model for finite-element structural analysis of turbine engine hot section components. This effort constitutes a different approach for nonlinear finite-element computer codes which were heretofore based on classical inelastic methods. A unified constitutive theory will avoid the simplifying assumptions of classical theory and should more accurately represent the behavior of superalloy materials under cyclic loading conditions and high temperature environments. Model development will be directed toward isotropic, cast nickel-base alloys used for aircooled turbine blades and vanes. The contractor will select a base material for model development and an alternate material for verification purposes from a list of three alloys specified by NASA. The candidate alloys represent a cross-section of turbine blade and vane materials of interest to both large and small size engine manufacturers. Material stock for the base and alternate materials will be supplied to the Contractor by the government.

Kaufman, A.↗
DOE OSTI2022

Role of Life Cycle Assessment in the Circular Economy

Industry leaders are increasingly turning to the circular economy to address a global need for reducing waste and reusing materials. Stakeholder pressure is mounting to establish better practices for more sustainable systems. Join your industry colleagues for an informative workshop to connect and accelerate standards development related to the circular economy of discarded manufacturing materials. The objective of the workshop is to develop a roadmap for ASTM technical standards to support the formation and engagement of manufacturers in a circular economy. Particular focus will be given to standards to support manufacturers in bringing their discarded materials into a mature materials marketplace as well as standards to measure and improve processing efficiencies resulting in reductions in discarded materials. The resulting roadmap will identify priorities for near-term standardization efforts. The roadmap will identify the necessary definitions for information flows supporting a sophisticate ecosystem for traceability and reuse of the materials. What is the role that life cycle assessment should have in setting manufacturing standards for applying circular economy strategies?

circular economy↗
DOE OSTI2021

Critical review and future prospects for desiccant coated heat exchangers: Materials, design, and manufacturing

Solid desiccant dehumidification is a promising alternative to vapor compression-based air-dehumidification to reduce energy consumption and improve air quality. Desiccant coated heat exchanger (DCHE), as one type of solid desiccant dehumidification system, can improve system performance and efficiency. The thermal performance and moisture removal capability of the DCHE greatly influence its dehumidification performance.The present work aims to critically analyze the designs, materials, and manufacturing methods of heat exchangers used for solid desiccant coating and look into recent developments in regular heat exchangers, potentially deployed as a substrate for DCHE applications. A comprehensive literature review of publications regarding solid desiccant materials, heat exchangers, manufacturing and coating methods, binder materials, and the performance of heat exchangers has been developed. Alternative heat exchangers are described as better options than fin and tube heat exchangers that have been considered thus far for DCHE applications. Additionally, the heat exchanger's manufacturing process and materials over their thermal and mass exchange performance have been analyzed. Despite the widespread use of fin and tube heat exchangers for solid desiccant coating, recent developments in heat exchanger design, and related fields such as manufacturing methods and materials, open the possibilities for their application in solid desiccant dehumidification systems. Lastly, the authors provide their outlook on possible developments of DCHE technology, aiming to increase systems' energy and dehumidification performance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling of Spark Plasma Sintering with Advanced Modeling to Enable Process Scale-Up: Presentation to DOE-NE [Slides]

The research goal of this project is to develop at Idaho National Laboratory (INL) a first-of-its-kind Multiphysics Object-Oriented Simulation Environment (MOOSE)-based, multiscale, multiphysics spark plasma sintering (SPS) modeling and simulation code application, termed “Freya.” Freya will simulate the thermo-mechanical-electrical aspects of the SPS fabrication process and will be paired with lower length scale sub-models, such as phase-field, to predict the resulting microstructure. SPS is an advanced manufacturing process that can be used to solve a variety of material manufacturing challenges; however, this process is an extremely challenging problem for modeling and simulation. The SPS process is inherently multiphysics and multi-scale, with the macroscale electro-thermo-mechanical behavior linked intricately to the microstructure evolution of the part being sintered. Accurate modeling and simulation tools, specifically geared towards the SPS process, are needed to predict the influence of the multiple variables involved in the manufacturing process. Modeling and simulation accuracy is achieved and demonstrated through comparison to multiple validation experiments. The validation efforts for Freya include both separate effects and complete multiphysics SPS process experiments. One of the key benefits this Laboratory Directed Research & Development (LDRD) project offers stems from the emphasis placed on experimental validation of the Freya models, both on the individual length scales and of the final coupled multiscale multiphysics simulations. Experimental validation of Freya’s multiscale coupling capability provides the technical credibility necessary for potential future industry and research partners to accept the simulation predictions.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Lessons learned for composite structures

Lessons learned for composite structures are presented in three technology areas: materials, manufacturing, and design. In addition, future challenges for composite structures are presented. Composite materials have long gestation periods from the developmental stage to fully matured production status. Many examples exist of unsuccessful attempts to accelerate this gestation period. Experience has shown that technology transition of a new material system to fully matured production status is time consuming, involves risk, is expensive and should not be undertaken lightly. The future challenges for composite materials require an intensification of the science based approach to material development, extension of the vendor/customer interaction process to include all engineering disciplines of the end user, reduced material costs because they are a significant factor in overall part cost, and improved batch-to-batch pre-preg physical property control. Historical manufacturing lessons learned are presented using current in-service production structure as examples. Most producibility problems for these structures can be traced to their sequential engineering design. This caused an excessive emphasis on design-to-weight and schedule at the expense of design-to-cost. This resulted in expensive performance originated designs, which required costly tooling and led to non-producible parts. Historically these problems have been allowed to persist throughout the production run. The current/future approach for the production of affordable composite structures mandates concurrent engineering design where equal emphasis is placed on product and process design. Design for simplified assembly is also emphasized, since assembly costs account for a major portion of total airframe costs. The future challenge for composite manufacturing is, therefore, to utilize concurrent engineering in conjunction with automated manufacturing techniques to build affordable composite structures. Composite design experience has shown that significant weight savings have been achieved, outstanding fatigue and corrosion resistance have been demonstrated, and in-service performance has been very successful. Currently no structural design show stoppers exist for composite structures. A major lesson learned is that the full scale static test is the key test for composites, since it is the primary structural 'hot spot' indicator. The major durability issue is supportability of thin skinned structure. Impact damage has been identified as the most significant issue for the damage tolerance control of composite structures. However, delaminations induced during assembly operations have demonstrated a significant nuisance value. The future challenges for composite structures are threefold. Firstly, composite airframe weight fraction should increase to 60 percent. At the same time, the cost of composite structures must be reduced by 50 percent to attain the goal of affordability. To support these challenges it is essential to develop lower cost materials and processes.

Whitehead, R. S.↗
DOE OSTI2025

Intelligent Manufacturing Support: Specialized LLMs for Composite Material Processing and Equipment Operation

Engineering educational curriculum and standards cover many material and manufacturing options. However, engineers and designers are often unfamiliar with certain composite materials or manufacturing techniques. Large language models (LLMs) could potentially bridge the gap. Their capacity to store and retrieve data from large databases provides them with a breadth of knowledge across disciplines. However, their generalized knowledge base can lack targeted, industry-specific knowledge. To this end, we present two LLM-based applications based on the GPT-4 architecture: (1) The Composites Guide: a system that provides expert knowledge on composites material and connects users with research and industry professionals who can provide additional support and (2) The Equipment Assistant: a system that provides guidance for manufacturing tool operation and material characterization. By combining the knowledge of general AI models with industry-specific knowledge, both applications are intended to provide more meaningful information for engineers. In this paper, we discuss the development of the applications and evaluate it through a benchmark and two informal user studies. The benchmark analysis uses the Rouge and Bertscore metrics to evaluate our models’ performance against GPT-4o. The results show that GPT-4o and the proposed models perform similarly or better on the ROUGE and BERTScore metrics. The two user studies supplement this quantitative evaluation by asking experts to provide qualitative and open-ended feedback about our model’s performance on a set of domain-specific questions. The results of both studies highlight a potential for more detailed and specific responses with the Composites Guide and the Equipment Assistant.

Kapoor, Gunnika [Oak Ridge National Laboratory (OR↗