Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material flow analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

MAGNETICALLY SUSPENDED CANNED ROTOR PUMPS FOR THE INTEGRAL MOLTEN SALT REACTOR

This project developed a molten salt pump design for small modular reactors, concentrated solar, and Gen IV nuclear reactors with a magnetically levitated rotor that can operate at temperatures of up to 700 °C. This eliminates the need for rotating seals and roller element bearings which require maintenance and are prone to failure. The pump design is also more compact than existing molten salt pump designs which require long shafts to thermally isolate the electric motor. The aims of the project are to: 1) design and test the molten salt pump, 2) develop and test a high temperature position sensor needed for magnetic bearing control, and 3) develop and test high temperature coil fabrication methods for electric motor and magnetic bearing fabrication. To develop the high temperature coils, conductor materials were analyzed for oxidation, diffusion, cladding, and resistivity. Of the candidate conductor materials that met the requirements, silver was chosen. The long-term impact of radiation on silver resistivity was analyzed by developing a model of a generic molten salt fast reactor to model the conductor irradiation in worst case scenarios. The analysis showed that increased resistivity due to transmutation of silver decreases exponentially with the reactor reflector thickness. Different electrical insulation materials were tested and the final high temperature coils developed were able to withstand conductor to ground voltages up to 1800 V before insulation breakdown. Magnetic bearings require high-precision high-speed measurements of the rotor position to operate. Current commercial position sensors can only operate up to 550 °C so a novel position sensor was developed that can operate up to 800 °C. These sensors were also designed to measure the position of the metallic rotor through a thin metallic corrosion barrier that protects that coils, insulation, and magnetic cores so that the salt containment barrier does not have any penetrations. The high-temperature sensor was tested and had comparable performance to commercially available inductive position sensors. The sensor design and signal processing has led to several invention disclosures. The magnetically levitated molten salt pump design was completed and analyzed. The chloride salt test loop at Oak Ridge National Laboratory was chosen to test the pump and the pump hydraulics and power were designed for the test loop flow and pressure requirements. Classes of motor designs that do not utilize permanent magnetic were considered for the high-temperature motor. After extensive analysis of their performance, a synchronous reluctance motor was chosen for the pump. The design was refined and analyzed to optimize performance. The magnetic bearings were designed to meet the force and frequency requirements necessary to levitate the rotor and reject disturbances from rotor imbalance, motor forces, and hydraulic forces. Compliant mounts for the position sensors were designed that would not damage the ceramic sensor components and maintain sensor alignment over a wide temperature range. A thermal hydraulic analysis of the molten salt coolant flow used to cool the rotor and stator was performed to ensure that the maximum temperature in the rotor and stator will not exceed 725 °C. The corrosion barrier and casing were designed to maintain the salt fluid boundary by using compliant features to absorb large expansion mismatches due to different coefficients of thermal expansion (CTE). Finally, the salt drain and fill systems were designed along with the pump support structure, integration with the test loop, and thermal insulation and heating. Corrosion barrier fabrication experiments were performed to assess using laser cladding to apply a sub-millimeter corrosion barrier to the surface of a Fe-Co-V magnetic core material. The cladding method showed minimal mixing between materials at their interface and withstood temperature cycling without damage to the cladding. The technology commercialization is focused on the high-temperature position sensors and there has been significant interest from the nuclear industry in utilizing these sensors along with some interest from the aerospace industry. The project also led to a research collaboration with a fusion energy industrial partner to study barriers to scaling the pump design from the kW size to the MW size. This research collaboration will also study methods to create high-temperature coils that have conductor to ground breakdown voltages above 5 kV. The successful development of high-temperature electromagnetic coils and high-temperature position sensors greatly increases the temperature limits for electromagnetic devices that don’t rely on permanent magnets. This includes electric motors, magnetic bearings, linear actuators, rotary position and velocity sensing, actuated valves, and generators to name a few. This will fill a current need in molten salt reactors, concentrated solar, and fusion energy for these critical peripheral devices needed for practical reactor designs that do not currently have commercial solutions.

Hines, J Wesley↗
DOE OSTI2022

Analysis of solid uranium particulates on cotton swipes with an automated microextraction-ICP-MS system

Here, an automated microextraction method coupled to an inductively coupled plasma – mass spectrometer (ICP-MS) was developed for the direct analysis of solid uranium particulates on the surface of cotton swipes. The microextraction probe extracts particulates from the sample surface, in a flowing solvent, and directs the removed analyte to an ICP-MS for isotopic determination. The automated system utilizes a mechanical XY stage that is software controlled with the capability of saving and returning to specific locations and a camera focused to the swipe surface for optimal viewing of the extracted locations (i.e., material present). Here, particulates (n = 135) were extracted and measured by ICP-MS, including 35 depleted uranyl nitrate hexahydrate (UN) (used for mass bias corrections), 50 uranyl fluoride (UO 2 F 2 ), and 50 uranyl acetate (UAc) particulates. Blank extractions were performed on the cotton swipes between triplicate sample analyses. Between each swipe extraction, the probe was sent between two wells containing 10% and 5% HNO 3 to clean the probe head and to eliminate any analyte carryover between particulates. The measured 235 U/ 238 U and 234 U/ 238 U isotope ratios for the UO 2 F 2 particulates were 0.00725(8) and 0.000054(4), a percent relative difference (% RD) of –0.041% and –1.7% from the reference isotope ratios determined in-lab through multi-collector ICP-MS analysis of dissolved aliquots of the U material. The UAc samples had a measured 235 U/ 238 U isotope ratio of 0.00206(7), a –0.96% relative difference from the reference value of 0.00208(1). The 234 U/ 238 U and 236 U/ 238 U isotope ratios were 0.000008(1) and 0.000031(4), –5.1% RD and –4.3% RD, respectively. The automated sample stage enabled seamless and rapid particle analysis, leading to a significant increase in throughput versus what was previously possible. Additionally, the saved location capability reduced user sampling error as sampling locations were easily stored and recalled. Analysis of U particles on the swipe surface – including blanks, mass bias, and triplicate extractions – was completed in less than an hour without any sample preparation necessary.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Molecular Dynamics Simulation and Theoretical Analysis of Structural Relaxation, Bond Exchange Dynamics, and Glass Transition in Vitrimers

Vitrimers are a class of polymer networks featuring dynamic covalent cross-links that can undergo associative bond exchange. There has been recent interest in these materials due to their promise as recyclable thermosets or self-healing polymers because of the ability of vitrimer networks to rearrange at the molecular level and undergo macroscopic flow. However, the practical use of these materials often occurs in the supercooled regime or glassy state, where the implications of dynamic bonds are complicated by the interplay between slow activated segmental dynamics, cross-link (i.e., bond-exchange) kinetics, and ultimately material properties. Here, in this paper, we combine coarse-grained molecular dynamics simulation and microscopic statistical mechanical theory to understand how cross-linking kinetics affect material dynamics and how this couples to segmental relaxation of the polymeric network strands across a spectrum of length and time scales, especially in the supercooled regime. We characterize the Kuhn segmental alpha relaxation time and bond exchange time for vitrimer systems across various cross-link densities, temperatures, and bond exchange rates. Simulation and theory both exhibit a bending-up behavior for bond exchange time upon cooling, suggesting a coupling between bond exchange dynamics and segmental relaxation that intensifies with faster bond exchange kinetics. We also found bond exchange dynamics have an impact on Kuhn segment alpha relaxation time, which is most significant at higher cross-link densities. Both these effects are most prominent when the bond exchange time is similar to the Kuhn segment alpha relaxation time, and the resulting coupling of these two relaxation processes is tied to both the probability of a free end to find a bonded pair and the time scale of the constraints imposed by the dynamic cross-links. This relationship is reflected by a cross-link dependence of a theoretical parameter which represents the quantitative degree of coupling between bond exchange and segmental dynamics. Overall, the combination of simulation and theory clarifies the intricate interaction between bond kinetics and segmental relaxation and demonstrates the ability to provide molecular-level insights into vitrimer dynamics over a wide temperature range.

dynamic relaxation↗
DOE OSTI2020

Rheological behavior of neat and carbon fiber-reinforced poly(ether ketone ketone) for extrusion deposition additive manufacturing

To develop new materials for extrusion additive manufacturing (AM) systems, a fundamental understanding of rheological properties is essential to correlate the effect of processing on material structure and its properties. In this work, the rheological properties of five different grades of neat and carbon fiber (CF)-reinforced poly(ether ketone ketone) are reported. Rheological properties are essential to understand the effect of reinforcing fibers and AM process parameters such as time, temperature, environment, and shear rate on flow behavior during processing. Small-amplitude oscillatory shear tests and steady shear tests indicated neat grades to exhibit less increase in viscosity over time when processed in air than the CF-filled grades. The filled grades showed greater shear thinning and lower sensitivity to temperature. Altogether, this rheological analysis provides a broad framework for determining appropriate processing conditions for extrusion deposition AM of such high-temperature polymer systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Contaminant Investigation and Pre‐Processing Opportunities for Textile‐To‐Textile Recycling

Millions of metric tons of textiles are landfilled or incinerated each year in the United States, with less than 1% of textiles recycled into new clothing or fabrics. To counter this trend, a growing number of companies and researchers are exploring how a circular economy can be applied to support textile‐to‐textile recycling. A significant barrier they face comes down to quickly and efficiently extracting pure feedstock material from post‐consumer garments that feature a mix of natural and synthetic fibers. Textile recyclers prefer pure feedstocks, as working with mixed sources typically means lower throughput, higher risk of equipment failure, and diminished business margins. To facilitate a circular economy for textiles, methods, and technologies are needed that can efficiently separate out materials and contaminants from end‐of‐life textiles to increase the flow of pure feedstocks to recyclers. This paper summarizes findings from interviews with a cross section of textile recyclers and from a review of literature to define basic feedstock requirements. In addition to our qualitative research, we deconstruct a bale of post‐consumer textiles and analyze them using computer‐vision imaging, Fourier transform infrared spectroscopy (FTIR), and machine learning. The resulting data are used to set system‐level design inputs for an automated contaminant removal system to process post‐consumer clothing into appropriate feedstocks for recycling. To set the system's levels for automated real‐time near‐infrared analysis, we identify the minimum percentage of primary material that any single garment in a load of used clothing must contain for the average of the full output stream to meet the target purity levels of recyclers. Here, the envisioned automated system can also address undesirable trace materials that might contaminate the processed stream by using imaging cameras coupled with artificial intelligence to identify sections of clothing for de‐trimming. Proof‐of‐concept machine learning algorithms are evaluated to locate and identify trims or garment areas with hidden contaminant materials. Integrating these methods into automated textile cutting systems can provide a cost‐effective means for increasing feedstock purity from used clothing, which can advance circularity for textiles by helping recyclers to reach production volumes and quality targets that were not possible solely with manual dismantling operations.

Parsons, Ryan [Rochester Institute of Technology, ↗
DOE OSTI2020

Investigating the compressive strength and strain localization of nanotwinned nickel alloys

Sputter deposited nickel-molybdenum-tungsten (Ni-Mo-W) thin films possess a beneficial suite of properties that stem from the extremely fine growth twins that form during the deposition process. Previously these materi- als were only characterized in tension, however, in this study in situ micropillar compression and post-mortem microstructural analysis of nanotwinned Ni 84 Mo 11 W 5 micropillars were employed to measure the compressive response and elucidate the attendant deformation mechanisms. The pillars exhibit Hookean behavior to com- pressive strengths of 3-3.5 GPa and the onset of non-linear plastic flow was manifest by discrete strain bursts and highly localized shear bands. Plastic deformation was concentrated at the top of the pillar, while the bulk of the micropillar was nominally unaffected. Post-mortem investigations indicate that at sufficiently high stresses shear banding is triggered, resulting in intense and highly localized plastic deformation that led to the formation of twin-free nanocrystalline grains within highly deformed shear bands. By contrast, the regions adjacent to the shear bands were unaffected. The absence of detwinning and dislocation glide mechanisms was unexpected and in direct contrast to what has been observed in nanotwinned Cu-Al. Post-mortem observations of the Ni-Mo-W micropillars suggest that the ultrafine twins create a unique form of dislocation starvation and source-limited plasticity. The ultrahigh compressive strength is governed by the triggering of shear bands rather than the activa- tion of dislocation glide. Finally, the specialized nature of plasticity in nanotwinned Ni-Mo-W is clear, even though the precise trigger for shear band formation in nanotwinned Ni-Mo-W remains to be identified.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fluidization of Group A Glass Particles: Experiments and Preliminary Validation

This work is aimed at providing reliable high-quality data from fluidization experiments. Geldart Group A glass beads are used as bed material. The fluidizing medium is air at atmospheric pressure which enters the system at 40% relative humidity. The air inlet velocity is varied over a broad range from 2 U mf to 26 U mf , where the minimum fluidization velocity, U mf , is 0.608 cm/s. There is not a significant change in the mean values of differential pressure; however, there are noticeable trends in their standard deviation values. Preliminary validation studies are performed using the open-source software Multiphase Flow with Interphase eXchanges (MFiX) developed by the National Energy Technology Laboratory (NETL). The results from Eulerian-Eulerian (MFiX-TFM, two-fluid model) and Eulerian-Lagrangian (MFiX-PIC, particle-in-cell) formulations are compared. The work presented in this report highlights the applicability of MFiX-PIC for large-scale applications, and reveals that PIC simulation offers a suitable alternative to TFM simulation when effects due to multiple components or polydispersity are significant. PIC modeling provides a readily extendible framework for such systems. However, PIC models do rely on an empirical closure for inter-particle stress. Some solution discrepancies were evident in MFiX-PIC predictions which require further analysis. As such, the study underlines the need for a systematic approach to quantify the sources of numerical uncertainty within the PIC model. However, even with known empiricism, MFiX-PIC has demonstrated considerable potential in analyzing gas-solid systems. The results obtained are encouraging and warrant further investigation to improve the predictive capability of MFiX-PIC.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A User’s Guide to the PLTEMP/ANL Code (V.4.3)

PLTEMP/ANL V4.3 is a program that obtains a steady-state flow and temperature solution for a nuclear reactor core, or for a single fuel assembly. It is based on an evolutionary sequence of codes originally used for plate temperatures, hence “PLTEMP”, developed at Argonne National Laboratory over several decades. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. Depending upon the heat transfer method selected, the temperature solution is effectively 2-dimensional or 3-dimensional (Appendix XV). It should be noted that for a 3-dimensional solution the axial power shape is modeled without accounting for axial heat conduction. It begins with a solution across all coolant channels and fuel plates or tubes within a given fuel assembly, at the entrance to the assembly. The temperature solution is repeated for each axial node along the length of the fuel assembly. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available to determine safety margins such as onset-of-nucleate boiling ratio(ONBR), departure from nucleate boiling ratio (DNBR), and onset of flow instability ratio (OFIR). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability is available (Appendix XII) to greatly reduce the reactor analyst’s time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Scaling for Nuclear Reactor System: Overview

A scaling analysis is essential for predicting the behavior of a reactor system under various operating conditions, as well as for ensuring safe and reliable experimentation and adequate dataset generation for supporting the system code model development and assessment in accordance with USNRC guidelines 1.203. Testing and modeling can be carried out at various scales, from small test units to full-scale reactors, to validate the predictions produced by the analysis. However, due to the cost and challenges associated with full-scale testing, the nuclear industry uses scaled test facilities—integral effect test (IET) and separate effect test (SET)—to identify potential design issues and optimize the design to ensure regulatory compliance for safer operation and anticipated accident management. In general, IET facilities are non-nuclear thermal hydraulics test facilities. In contrast, SET facilities can be non-nuclear testing (e.g., steam generator, containment, pump system SETs) and nuclear testing (mostly fuel-material irradiation testing). IETs are used to study the system-level thermal-hydraulic behavior of the reactor coolant system (RCS) under different anticipated operational occurrences (AOOs) and design basis accidents (DBAs) such as loss-of-coolant-accident (LOCA) and loss-of-power (i.e., station blackout) and loss-of-flow (i.e., failure of RCS pump). Several LOCA scenarios could happen in reactor DBAs, such as main steam line break (MSLB), SG tube rapture (SGTR), break in direct vessel injection (DVI), and other small breaks LOCA. Scaling analysis determines the appropriate size and operating conditions for the test facility. This involves analyzing the system's thermal-hydraulic behavior at different scales and identifying the key parameters that affect the thermal-hydraulic behavior of the reactor. These key parameters can be identified so that the scaled facility can replicate the expected conditions in a prototypical setting. The scaled facility can simulate the same flow rates, pressure gradients, heat transfer coefficients, and fluid properties as the prototype. Scaling analysis is used to ensure that the results from these tests can be scaled up to predict the behavior of a full-scale prototype with an acceptable range of scaling distortions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

Structural uniformity and compositional homogeneity of solid-phase alloyed rod

Solid-phase processes have emerged as an alternative to fusion-based alloying to avoid coarse microstructures, undesirable phase formation, and high energy consumption. However, achieving uniform distribution of alloying elements during friction-based processing remains challenging due to highly heterogeneous thermomechanical conditions. This work evaluates the structural uniformity and compositional homogeneity of Al–Cu–Zn alloyed rods produced by friction extrusion (FE) and establishes the role of the rotational speed to feed rate ratio (N/V) on alloying effectiveness. A systematic matrix of FE experiments was conducted at constant extrusion ratio with N/V values ranging from 3.7 to 300. Compositional uniformity was assessed along the rod length (ICP-OES), in three dimensions (X-ray computed tomography), and at the microscale (SEM–EDS), supported by a gray-level co-occurrence matrix (GLCM)–based homogeneity metric. Smoothed particle hydrodynamics (SPH) simulations were used to reveal material flow and thermomechanical fields. Results show that N/V = 100 produces a high-shear mixing zone that eliminates the unmixed core and enables near-full dissolution and dispersion of Cu and Zn. At lower N/V, a laminar flow region persists at the rod center, causing segregation and large composition gradients. The combined experimental–computational analysis provides mechanistic insight into the transition from fragmented particle dispersion to thermomechanically assisted metallurgical mixing. This study establishes processing–structure relationships for solid-phase alloying and provides guidance for achieving homogenized compositions comparable to wrought alloys via rapid, scalable FE processing.

Aluminum↗
DOE OSTI2025

Advanced Model Development for Large Eddy Simulation of Oxy-Combustion and Supercritical Carbon Dioxide Power Cycles

A joint experimental and numerical study is performed to observe the characteristics of a supercritical carbon dioxide turbulent mixing layer in the presence of strong nonlinearities in the thermodynamic and transport properties. A bespoke experimental setup is designed and employed for this purpose and provides insight into macroscopic mixing behavior. The mixing is experimentally observed using two techniques: shadowgraphy and spontaneous Raman scattering. Qualitative and quantitative intensity fields obtained via these techniques yield instantaneous and mean density data. Spanwise temperature data is also collected using analogue resistance temperature detectors. These measurements are used to quantify the level of mixed material within the field. The experimental data are supplemented by a companion high-fidelity numerical study. The numerical results are obtained through fully resolved, three-dimensional direct numerical simulation. The numerical dataset permits observation of the near-field mixing characteristics, which are difficult to measure experimentally due to the rapid dynamics and sharp thermophysical gradients in this area. Qualitative field visualizations are presented, followed by quantitative mixed material results and observations regarding thermodynamic property trends at select locations within the field. One-dimensional spectra of the turbulent kinetic energy and solenoidal dissipation are provided to observe the spectral characteristics of the flow. Reynolds stress anisotropy is analyzed graphically through anisotropy invariance maps (Lumley triangles). The mixing quantification, spectral data and anisotropy analysis of a flow at these thermodynamic conditions represent the main outcomes of the work.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Unraveling the discontinuous plastic flow of a Co-Cr-Fe-Ni-Mo multiprincipal-element alloy at deep cryogenic temperatures

We report an analysis of the discontinuous plastic flow of a multiprincipal-element alloy, Co 17.5 Cr 12.5 Fe 55 Ni 10 Mo 5 (atomic percent, at. %), in the temperature range of 0.5–4.2 K showing serrated deformation curves. Using the analytical techniques, we studied the statistics of the stress drops associated with the unstable plastic flow. The analysis showed that the complexity and heterogeneity of a discontinuous plastic flow were reduced when the temperature was lowered. This behavior was associated with the effects of dynamic recovery and adiabatic heating on the dislocation-density evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Insights into the Enhanced Oxidative Thermal Stability of Nanoparticle Organic Hybrid Materials Developed for Carbon Capture and Energy Storage

Due to the growing need for Direct Air Capture (DAC) and integrated carbon capture and conversion technologies, CO 2 capture materials that can withstand a wide range of environmental conditions, including fluctuating ambient temperatures and high concentrations of oxidizing agents (i.e., oxygen and moisture), are critically needed. Liquid-like Nanoparticle Organic Hybrid Materials (NOHMs) have been proposed as candidates for DAC and electrolyte additives enabling sustainable energy storage (i.e., integrated CO 2 capture and conversion and flow batteries). Liquid-like NOHMs functionalized with an ionic bond have been shown to display greatly enhanced oxidative thermal stability compared to the untethered polymer. However, these studies were limited in terms of reaction conditions and the detailed mechanisms of the oxidative thermal degradation were not reported. In this work, a kinetic thermal degradation analysis was performed on NOHM-I-HPE and the neat polymer, Jeffamine M2070 (HPE), in both non-oxidative and oxidative conditions. NOHM-I-HPE displayed similar thermal stability to the untethered polymer in a nitrogen environment, but interestingly, the thermal stability of the ionically tethered polymer was significantly enhanced in the presence of air. This observed enhancement of oxidative thermal stability is attributed to the orders of magnitude larger viscosity of the liquid-like NOHMs compared to untethered polymer and the bond stabilization of the ionically tethered polymer in the NOHMs canopy. Further, spectroscopic analyses of the liquid residue revealed that in the presence of oxygen, the degradation of HPE and NOHM-I-HPE occurs through the formation of trace amounts of carbonyls. This study illustrated that NOHMs can serve as functional materials for sustainable energy storage applications because of their excellent oxidative thermal stability.

25 ENERGY STORAGE↗
DOE OSTI2021

Solidification dynamics in metal additive manufacturing: analysis of model assumptions

Solidification characteristics in the meltpool drive the process-microstructure relationship which helps dictate the material properties of as-built parts in additive manufacturing; therefore, being able to accurately and quickly simulate the size, shape, and solidification characteristics in the melt pool is of great interest to the field. In this study, we investigate various important physical phenomena (dynamic material properties, fluid-flow, radiation and vaporization) which can either be included or neglected in a continuum finite volume model (FVM) and their effect on the solidification conditions. Additionally, since the simplest form of such a model (conduction only) has an analytic solution which is much faster, its viability is also considered. Since the inclusion of some of these physical phenomena will inherently change the net energy input as well as the amount of energy needed to achieve melting of a control volume, each set of included phenomena had an effective absorption efficiency which was calibrated to closely match the dimensions of the melt pool to that of the ground truth data. The ground truth data for this study was defined to be the output of the FVM which included all the physical phenomena (OF). This study then goes on to compare the effects on solidification conditions each of these calibrated models has. It was found that most of the change in solidification conditions comes from the inclusion of latent heat. A posterior correlation factor (PCF) is then introduced to enable an analytic model to predict similar solidification conditions to OF model.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Combined Cr and S poisoning behaviors of La 1-x Sr x MnO 3±δ and La 1-x Sr x Co 1-y FeyO 3-δ cathodes in solid oxide fuel cells

Although the individual effects of airborne Cr and S contaminants on SOFC cathode performance degradation have been extensively studied, the combined effects of Cr and S contaminants remain largely unexplored. Under the real SOFC operating condition where the Cr and S species coexist, their effects may compete, affecting the poisoning behavior. Here, our investigation reveals that the combined Cr and S poisoning behavior of LSCF remains different from those of individual Cr and S poisonings, while the combined poisoning mechanism of LSM is equivalent to the sum of those of individual Cr and S effects. For LSCF electrode, gaseous Cr species are deposited mainly at the LSCF/GDC interface by electrochemical reduction, rather than forming SrCrO 4 on LSCF surfaces (as in the case of Cr-only poisoning), indicating no reaction between Cr vapors and SrO on the LSCF surface. Thermodynamic analysis demonstrates that the SrO on LSCF surface absorbs SO 2 (g) and thereby loses the Cr-gettering effect, allowing Cr vapors to flow through LSCF and to reach the LSCF/GDC interface where the Cr deposition occurs. Unlike LSCF, LSM electrode shows cumulative effects of Cr and S, as Cr accumulation occurs at the triple-phase boundary and S absorption takes place at localized Sr-rich regions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Minimum GHG emissions and energy consumption of U.S. PET and polyolefin packaging supply chains in a circular economy

There is a wide agreement on the urgency of transforming linear management of plastics towards a circular economy model. However, no clear pathways exist as to required recycling technologies involved and system-wide environmental impacts. This study explores such pathways in the U.S. for the most commonly used packaging plastics through a combination of mechanical and emerging advanced recycling technologies. A system optimization model aimed at minimizing environmental impacts was developed to determine optimal end-of-life (EOL) management and locations of existing and emerging U.S. recycling infrastructures. Our study includes material flows from virgin resin production through semi-manufacturing processes to existing EOL disposal and recycling processes. An optimized circular plastics packaging system achieved greenhouse gas (GHG) emission savings of up to 28% and cumulative energy demand (CED) savings of up to 46%, compared to the linear economy. Moreover, these savings of GHG emissions and CED impacts represent a reduction of 0.16% and 0.49% compared to annual U.S. GHG emissions and energy consumption in 2022, respectively. The optimal recycling rates and systems-level circularity ranged from 78–99% and 57–75%, respectively. Increased energy savings led to increased GHG emissions showing a potential trade-off between GHG emissions and energy. Analysis of 40 scenarios showed the importance of material collection distances, blend limit of mechanically recycled resins, process yields, and mandated recycling rates for achieving a sustainable circular economy of plastics.

09 - BIOMASS FUELS↗
DOE OSTI2021

One of These Things IS Like the Other: Pursuing a New Taxonomy of Industry for Improved Energy System Modeling

Industrial processes drive the exchange of materials, energy, and currency throughout the economy. These processes are powered by electricity and direct combustion, with variation in their operation even within the same industry. This heterogeneity makes it difficult for large models, including the National Energy Modeling System (US), to project their energy use while remaining tractable. Decarbonization and ensuing changes to the energy system require changes to industrial processes while offering opportunities for process innovation, but the extent and nature of changes are difficult to model with current classification schemes and corresponding data. The North American Industrial Classification (NAICS) is an economic taxonomy of industries, but its categories are less meaningful from an energy and material flow perspective. For example, a facility that makes steel from iron ore in a blast furnace/basic oxygen furnace is categorized under the same NAICS code as a facility that makes steel from scrap in an electric arc furnace despite the scale, use of recycled scrap versus iron ore, and energy use differences in the two facility types. Exploratory analysis is performed on a large dataset used for plant-level energy assessment in order to detect clusters that can aid in better modeling of industry for energy analysis in an evolving system with breakthrough technologies.

28 EE - Advanced Manufacturing Office (EE-5A)↗
DOE OSTI2025

Rapid analysis of 237 Np and Pu isotopes in unseparated sample matrices using ICP-MS/MS

Inductively coupled plasma tandem mass spectrometry (ICP-MS/MS) is an emerging technique for measuring actinide isotopes when assessing pre- and post- detonation nuclear material. In this study, ICP-MS/MS was investigated for direct Np and Pu quantitation in unseparated, dissolved bulk soil matrices. To achieve this, purified nitric oxide (NO) was investigated for the reactivity of Th, Np, U, Pu, Am, and Cm. Purifying NO prior to the collision reaction cell (CRC) results in increased sensitivity and allows for higher gas flows to be utilized for the removal of interferences. Here, the interference from uranium hydrides was mitigated to less than 3.85 x 10 -11 . This method was demonstrated on standard reference materials which were measured for 237 Np and 238,239,240 Pu in dilute sample digestions. The 238 Pu measurement was validated by spiking into a standard reference material and was accurately measured with an excess of 85000 of 238 U.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗