Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Tailored Microstructure and Properties in UO{sub 2}

Advanced fuels with enhanced safety margin and accident tolerance are of vital importance for safe operation of current light water reactor fleet and the development of future reactor systems. The current UO{sub 2} fuel for LWRs has low thermal conductivity, which will be further reduced upon burn-up. The intrinsically low thermal transfer efficiency of the oxide fuels results in a large temperature gradient within the fuel pellet and high center-line temperature. Thermal swelling of the pellets and fission product accommodation and retention limit the lifetime of UO{sub 2} fuel in the reactor, presenting the great challenges for extending burn-up, effective utilization of nuclear resources and minimization of nuclear waste accumulation. Critical needs also exist in developing accident tolerant fuels that can tolerate loss of coolant accident or improve fuel performance under regular operation or beyond design scenario. Key properties of advanced fuels include high thermal conductivity, oxidation resistance, high temperature mechanical properties, fission gas retention capability and thus improved accident tolerance. The US Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is developing science-based next generation fuel performance modeling capability as part its Fuel Product Line in order to facilitate the predictive capability of nuclear fuel performance and assist the design and analysis of reactor systems. Critical experimental data are needed to validate MARMOT models, particularly on effective thermal transport, fracture mechanisms, grain growth kinetics and fission gas behavior. The fabrication of sintered fuel pellets with well-controlled microstructure is prerequisite to establish the correlation of the microstructure features and fuel behavior in order to develop high fidelity fuel performance models. In this talk, recent advancements on developing advanced UO{sub 2} fuels and properties improvement are overviewed with the emphasis on different accident tolerant fuel (ATF) concepts and tailoring microstructures for MARMOT validation. Current efforts on ATFs include composite fuels and high-density fuels to improve thermal-mechanical properties and fission gas retention capabilities. Different composite UO{sub 2} fuels are fabricated with heterogeneous phases as sintering additives for microstructure and property control, and the potential application of the composites as advanced fuels with enhanced accident tolerance will be discussed. In addition, recent progresses of using field-assisted sintering technologies, specifically spark plasma sintering (SPS), in tailoring and engineering fuel matrix as the target systems for validating MARMOT physics models will be highlighted. Particularly, monolithic UO{sub 2} with tailored microstructure including grain size across multiple length scales from nano-metered to micron-sizes, porosity and stoichiometry can be sintered. The impacts of tailored microstructure on thermal-mechanical properties and grain growth kinetics are discussed within the context of the MARMOT modeling. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

The microstructure and mechanical properties of Al-containing 9Cr ODS ferritic alloy

In this study, a 9Cr oxide-dispersion strengthened (ODS) alloy with additional corrosion resistant element Al was fabricated by mechanical alloying (MA) and hot pressing (HP) to explore the impact of Al on the microstructure and mechanical property of a 9Cr ODS alloy. It is found that the Al completely dissolved into the FeeCr matrix after milling for 30 h. The minor phases in the Al-containing 9Cr ODS ferritic alloy were investigated by a high-energy X-ray, and were identified to be orthorhombic-YAlO3 (YAP), bcc-Y3Al5O12 (YAG), monoclinic-Al2Y4O9 (YAM), and hexagonal-YAlO3 (YAH). These phases were further confirmed by selected area diffraction pattern (SADP), energy dispersive spectroscopy (EDS), and high resolution transmission electron microscopy (HRTEM). In addition, their volume fractions were also calculated from the integrated intensities. According to the analysis of the particles and their formation sequences, the larger particles (greater than 100 nm) are identified as mainly YAG and Al2O3 particles, while the particles with small size (less than 30 nm) are likely primarily YAM, YAH, and YAP particles. The yielding strength (YS) and ultimate tensile strength (UTS) at RT are 563 MPa and 744 MPa, respectively, while the YS and UTS at 700 C are 245 MPa and 276 MPa, respectively. Although the addition Al in ODS alloys decreases the strength at RT, the values at high temperature are similar to those obtained for 9Cr ODS alloys strengthened by fine YeTieO particles.

Microstructure↗
DOE OSTI2020

Effects of carbonitrides and carbides on microstructure and properties of castable nanostructured alloys

In this work, to develop advanced reduced-activation ferritic-martensitic (RAFM) steels for fusion reactor structural applications, both carbonitride- and carbide-strengthened castable nanostructured alloys (CNAs) were explored for higher densities of MX (M = Ti/Ta/V/etc. and X = C/N) nanoprecipitates. Additionally, systematic comparisons between the two types of CNAs indicated generally similar microstructures and comparable tensile properties and creep resistance. However, the carbide-CNAs did show some advantages over the carbonitride-CNAs in terms of the uniformly distributed higher density of MC nanoprecipitates, greater Charpy impact upper shelf energies, less deuterium retention and swelling, and potentially less transmutation-induced composition changes and consequently thermodynamically more stable carbides. The carbide-CNAs showed the best-balanced high performance in the examined properties, in contrast to the significantly varied performance of oxide-dispersion-strengthened alloys and the generally lower performance of current RAFM steels.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Formability, Microstructure and Mechanical Properties of Flow-Formed 17-4 PH Stainless Steel

The subject of the research that has been conducted in this paper was to analyze precipitation-hardened martensitic stainless steel 17-4 PH after flow forming with four different strains and subsequent standard heat treatment. Four cylinders were obtained with a 16, 30, 48 and 68% reduction in thickness, respectively. The samples were analyzed in terms of their mechanical properties and microstructural changes before and after the heat treatment. The results showed that a higher strain resulted in an overall higher strength (up to 1200 MPa UTS) and refinement of the structure, although at a cost of the elongation. High deformation influenced the precipitation process, and the ratio of the grain boundaries significantly increased. Nonetheless, comparing the obtained results with other similar research, it seems that the formation of nano-precipitates of Cu is the key-strengthening mechanism. Strain hardening contributes to an increase in the strength of the steel, although the effect decreases after heat treatment. The relatively small values of residual stress in the steel, especially after the heat treatment, confirmed these claims. Overall, flow forming allowed high deformations of the 17-4 PH steel to be obtained although it did not significantly change the mechanical properties of the material due to the dominant precipitation hardening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructural and magnetic property evolution with different heat-treatment conditions in an alnico alloy

Further property enhancement of alnico, an attractive near-term, non-rare-earth permanent magnet alloy system, primarily composed of Al, Ni, Co, and Fe, relies on improved morphology control and size refinement of its complex spinodally decomposed nanostructure that forms during heat-treatment. Using a combination of transmission electron microscopy and atom probe tomography techniques, this study evaluates the magnetic properties and microstructures of an isotropic 32.4Fe-38.1Co-12.9Ni-7.3Al-6.4Ti-3.0Cu (wt.%) alloy in terms of processing parameters such as annealing temperature, annealing time, application of an external magnetic field, as well as low-temperature “draw” annealing. Optimal spinodal morphology and spacing is formed within a narrow temperature and time range (~840 °C and 10 min) during thermal-magnetic annealing (MA). The ideal morphology is a mosaic structure consisting of periodically arrayed ~40 nm diameter (Fe-Co)-rich rods (α 1 phase) embedded in an (Al-Ni)-rich (α 2 phase) matrix. A Cu-enriched phase with a size of ~3–5 nm is located at the corners of two adjacent {110} facets of the α 1 phase. The MA process significantly increased remanence (B r ) (~40–70%) of the alloy due to biased elongation of the α 1 phase along the <100> crystallographic direction, which is closest in orientation to the applied magnetic field. As a result, the optimum magnetic properties of the alloy with an intrinsic coercivity (H cj ) of 1845 Oe and a maximum energy product (BH max ) of 5.9 MGOe were attributed to the uniformity of the mosaic structure.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Annealing Temperature on Microstructure and Magnetic Properties of Ni{sub 0.05}Zn{sub 0.95}Fe{sub 2}O{sub 4} Nanoparticles

The magnetic behavior of Ni{sub 0.05}Zn{sub 0.95}Fe{sub 2}O{sub 4} nanoparticles synthesized by the sol–gel technique route was clarified To figure out the influence of annealing temperature on the structure of Ni{sub 0.05}Zn{sub 0.95}Fe{sub 2}O{sub 4} particles, x-ray diffraction (XRD) tool was used and revealed spinel cubic structure without any secondary phases. The particle formation and sizes were obtained using scanning electron microscope (SEM). Elemental composition of the nanoparticles was also provided by an energy-dispersive x-ray analysis tool (EDX). The magnetic behaviors of the synthesized powders annealed at varying temperatures were determined by vibrating sample quantum design PPMS measurement system tool. The M–H curves of the samples showed that the samples had S-shape but they reached no saturation state at the presence even at 30 kOe.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Effect of Boron Content on Microstructure, Mechanical Properties, and Oxidation Resistance of Mo-Si-B Composites

Mo-Si-B composites with boron content from 0 to 8 wt.% were prepared by spark plasma sintering using Mo, Si, and B elemental powders. The effects of boron content on the phase composition, mechanical properties, and high-temperature oxidation resistance of the Mo-Si-B composites were investigated. The results show the evolution of the major phase constitution of the composites with increasing boron content is in the following sequence: (MoSi{sub 2}, Mo{sub 5}Si{sub 3}) → (MoSi{sub 2}, Mo{sub 5}Si{sub 3}, Mo{sub 5}SiB{sub 2}) → (MoSi{sub 2}, MoB) → (MoSi{sub 2}, MoB, MoB{sub 2}). As the boron content increases, both the hardness and flexural strength of the composites increases, but the fracture toughness of the composites gradually decreases. The strengthening mechanisms for the composites are second-phase strengthening and grain refinement strengthening. However, the formation of brittle phases, i.e., Mo{sub 5}SiB{sub 2}, MoB, and MoB{sub 2}, reduces the toughness of the composites. In addition, since a dense barrier layer of SiO{sub 2}-B{sub 2}O{sub 3} formed on the surface of the composites inhibits the inward diffusion of oxygen, B-doped Mo-Si-B exhibits better oxidation resistance compared with non-doped composites.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Chemical Composition on the Microstructure and Tribological Properties of Sn-Based Alloys

This article presents the test results of two bearing alloys on a tin matrix, differing in the content of alloy additions. Microscopic tests were performed using scanning electron microscopy, along with Brinell hardness tests and tests of tribological properties in the conditions of technical dry friction and wet friction using a TU-32 oil. Additionally, wear mechanisms were analyzed depending on the process conditions. The results indicate better tribological properties of the B82 alloy, with a higher content of antimony compared to the B89 alloy. This alloy contains more precipitates of hard phase β—SnSb, which both influence the level of the mechanical properties and determine the tribological properties. Additionally, it was proven that using the TU-32 oil as a lubricant practically eliminates adhesive wear, and the post-friction surfaces for both alloys are of a similar nature.

36 MATERIALS SCIENCE↗
DOE OSTI2015

The effect of thermomechanical treatment regimes on microstructure and mechanical properties of V–Me(Cr, W)–Zr–C alloys

The regularities of the formation of a heterophase structure in dispersion-strengthened vanadium V–Me(Cr, W)–Zr–C alloys are studied as a function of the regimes of their thermomechanical treatment. The regimes of treatment providing a substantial increase in the dispersity and homogeneity of spatial distribution of ZrC particles, temperature of recrystallization, and high-temperature (at T = 800°C) short-time strength are found in comparison to conventional treatment regimes.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Mechanical Properties of Multilayer α-AlN/α-BCN Coating as Functions of the Current Density during Sputtering of a B{sub 4}C Target

Multilayer AlN/BCN coating of nanometer scale have been prepared by magnetron sputtering of Al and B{sub 4}C targets in an argon–nitrogen atmosphere during deposition on a Si substrate. These coating have an X-ray amorphous structure and the maximum Knoop hardness of 27 GPa (at the current density 100 mA). The first-principle molecular dynamics calculations show that the B4–BN layer is dynamically unstable; thus, it will not be epitaxial and will be amorphous or have a structure different from the B4–BN structure. The thermal vacuum annealing from 600 to 800°C of samples with multilayer nanosized coating leads to the decrease in the Knoop hardness to 18 GPa; however, the coating structure is retained X-ray amorphous.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗
DOE OSTI2019

Design and Development of Galvannealed Dual-Phase Steel: Microstructure, Mechanical Properties and Weldability

It was attempted to produce galvannealed dual-phase (DP) steel through a commercial continuous galvanizing line (CGL). The main challenge was to form the DP microstructure even with the slow cooling rate after annealing in the CGL. A two-pronged approach was adopted for this, viz. design of the steel chemistry with calculations and optimization of the CGL parameters with simulation using Gleeble-3800 thermomechanical simulator. The steel thus produced in CGL revealed ferrite and 18 ± 2% martensite microstructure, with tensile strength exceeding 600 MPa and 24% total elongation along with good formability. Weldability study using resistance spot welding indicated the possibility of achieving sound joint with a 4-kA width in weld time–current lobe despite the high carbon equivalence.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and properties of additively manufactured Al–Ce–Mg alloys

Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al–Ce–Mg system, designed as near-eutectic (Al–11Ce–7Mg) and hyper-eutectic (Al–15Ce–9Mg) compositions with respect to the binary L → Al + Al 11 Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The effect of finish rolling temperature and tempering on the microstructure, mechanical properties and dislocation density of direct-quenched steel

Highlights: • The effect of thermomechanical treatment and tempering on direct-quenched steel has been studied. • Dislocation density of direct-quenched and tempered martensite is evaluated using both TEM and Williamson-Hall method. • Statistical analysis has been performed to study the effect of different factors on toughness of direct-quenched martensite. - Abstract: A unique batch tempering treatment for industrial scale direct-quenched steel coils has been studied using laboratory simulations. The tempering treatment was non-isothermal with slow heating to 570 °C and slow cooling to simulate the tempering of large steel coils. The paper presents the effect of finishing rolling temperature (FRT) relative to the non-recrystallization temperature (T{sub NR}) and the effect of long time tempering on the microstructure, dislocation density and mechanical properties of direct-quenched coiled strips. Conditioning austenite below the recrystallization stop temperature resulted in a finer effective grain size distribution, which correlated strongly with the impact toughness of the final product. Furthermore low finish rolling temperature resulted in partially ferritic microstructures while higher finishing rolling temperatures led to mixtures of bainite and martensite. Dislocation densities determined with TEM and XRD showed somewhat different trends regarding the effect of tempering: intra-lath dislocation density, as measured with TEM, showed a statistically significant drop in only one case, while XRD analysis indicated a drop in all cases. Furthermore, no significant correlation between finishing rolling temperature and dislocation density existed in XRD studies. The XRD results indicate that the decrease in dislocation density corresponds to about 100 MPa lower dislocation strengthening. However, precipitation hardening and potential internal micro stress relief compensates this as yield strength remains unchanged or even increases during tempering.

36 MATERIALS SCIENCE↗