SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flight acoustical and performance evaluations of DC 8 nacelle modifications to reduce fan-compressor noise in airport communities
Development of acoustic lining for turbofan nacelle modification to minimize fan compressor noise radiation
Subjective evaluation tests of ground observers on relative noise from acoustically treated engine nacelles of Boeing 707 aircraft
Interaction of nacelle-mounted supersonic propulsion system with simulated wing boundary layer
Afterburner-equipped jet engine nacelle with slotted configuration afterbody
Thrust measurement system and aerodynamic drag effects of underwing J-85 engine nacelles on F-106 aircraft propulsion system performance
Low speed wind tunnel tests of effects of nacelle position, refaired fuelage, and elevator effectiveness for NAR straight wing orbiter
Airframe installation effects on underwing nacelle nozzle performance, using calibrated engines and load cells on F-106 for measurements
Stellar UV cut-off by statospheric nacelle recorded on photographic film by Schmidt telescope fitted with objective prism, widening spectrum by scanning
A modified F-106B aircraft with underwing engine nacelles was flight tested to investigate airframe installation effects on ejector nozzles. Nozzle thrust coefficients, boattail drag coefficients, and boundary layer characteristics were obtained for the three nozzles. All the nozzles were geometrically similar and had 15 deg conical boattails with juncture radii of curvature equal to 0.5 maximum nozzle diameter. The effects of boattail location relative to the wing trailing edge and the ejector to primary nozzle exit diameter ratio were investigated. Shortening the length by 0.48 nozzle diameter lowered the transonic boattail drag rise Mach number from 0.97 to 0.95. Decreasing the nozzle exit diameter, which reduced the ejector to primary nozzle exit diameter ratio from 1.30 to 1.18, increased the gross thrust coefficient 4.8 percent.
A description is given of the ground test quiet nacelle for the TF34 engine. The suppression treatment consists of cylindrical splitters in the inlet and fan exhaust ducts plus duct wall treatment and core exhaust wall treatment. Aerodynamic design analysis of the inlet and exhaust ducts and overall engine performance with pressure losses from the acoustic treatment is included. The objectives of the test program are to obtain noise data for a heavily suppressed high bypass turbofan with various arrangements of exhaust systems and acoustic treatment, and to provide a basis for the power plants of the Quiet Experimental STOL Aircraft (Questol).
To determine flyover noise and thrust and to investigate whether flight velocity significantly affects the noise of exhaust nozzles, a series of flight tests was conducted on three different exhaust nozzles of a type suitable for supersonic transport aircraft. The tests were conducted using an F-106B aircraft modified to carry two underwing nacelles, each containing a calibrated turbojet engine. A flyover altitude of 91 meters (300 ft) and a Mach number of 0.4 provided acoustic data that were repeatable to within + or -1.5 PNdB. Flyover results showed that an auxiliary inlet ejector nozzle was the quietest of the nozzles tested; flight velocity appeared to reduce its noise.
The investigation was made on a 1/18-scale model of a twin-engine light airplane. Static longitudinal, lateral, and directional characteristics were obtained at 0 deg and plus or minus 5 deg sideslip at a Mach number of about 0.2. The angle of attack varied from about 20 deg at a Reynolds number of 0.39 times one million to 13 deg at a Reynolds number of 3.7 times one million, based on the reference chord. The effect of fixed transition, vertical and horizontal tails, and nacelle fillets was studied.
Theoretical Mach number distributions and boundary-layer parameters are presented for subsonic nacelle inlet diffuser geometries with length to exit diameter ratios ranging from 0.4 to 1.6 and diffuser exit area to throat area ratios ranging from 1.1 to 2.0. The major portion of the study was done with a cubic diffuser contour with the inflection point at the midpoint of the diffuser, a diffuser throat Mach number of 0.6, and a free-stream Mach number of 0.12. Calculations were performed at both model (diffuser exit diameter, 30.5 cm) and full-scale (diffuser exit diameter, 183 cm) sizes. Separation limits were defined by establishing a separation boundary on plots of diffuser area ratio as a function of diffuser length to diameter ratio. The effects of diffuser contour, inlet lip geometry, and throat Mach number on the boundary-layer characteristics are illustrated. The major results of the study indicate that the separation boundary is shifted to greater area ratios by (1) increasing the diffuser length, (2) increasing the scale of the diffuser and, (3) moving the inflection point of the diffuser contour to or ahead of the midpoint of the diffuser.
The results of the nearfield acoustic tests conducted on the TF34 Quiet Nacelle are presented. The high fan noise suppression levels being sought (26 PNdB reduction in aft noise) necessitated the use of an extensive system of special nearfield acoustic instrumentation to properly evaluate the suppression achieved. The design, operation, and test results from each of these nearfield acoustic instrumentation systems are presented.
A method has recently been developed for calculating the flow over a subsonic nacelle at zero angle of attack. The method makes use of annular wing theory and boundary-layer theory and has shown good agreement with both experimental data and more complex theoretical solutions. The method permits variation of the mass flow by changing the size of a center body.
A 1/10-scale powered model of a twin-engine attack airplane was investigated in the Langley high-speed 7- by 10-foot tunnel. The study was made at several Mach numbers between 0.225 and 0.75 which correspond to Reynolds numbers, based on the mean aerodynamic chord, of 1.35 million and 3.34 million. Unheated compressed air was used for jet simulation in the nonmetric engine nacelles which were located ahead of and above the horizontal stabilizer.
The procedures required to operate the thick wing and pylon-fuselage-fanpod-nacelle computer program are presented. The program computes surface velocities and pressure, section loads, and total configuration loads and pitching moment. Potential flow theory is used to compute the surface pressures and the associated lift, moment, and vortex drag. The skin friction drag is also computed.