Results for “Oil flow visualization” — Page 12

NASA NTRS2002

Visualization of Flows in Packed Beds of Twisted Tapes

A videotape presentation of the flow field in a packed bed of 48 twisted tapes which can be simulated by very thin virtual cylinders has been assembled. The indices of refraction of the oil and the Lucite twisted tapes were closely matched, and the flow was seeded with magnesium oxide particles. Planar laser light projected the flow field in two dimensions both along and transverse to the flow axis. The flow field was three dimensional and complex to describe, yet the most prominent finding was flow threads. It appeared that axial flow spiraled along either within the confines of a virtual cylindrical boundary or within the exterior region, between the tangency points, of the virtual cylinders. Random packing and bed voids created vortices and disrupted the laminar flow but minimized the entrance effects. The flow-pressure drops in the packed bed fell below the Ergun model for porous-media flows. Single-twisted-tape results of Smithberg and Landis (1964) were used to guide the analysis. In appendix A the results of several investigators are scaled to the Ergun model. Further investigations including different geometric configurations, computational fluid dynamic (CFD) gridding, and analysis are required.

Hendricks, R. C.↗

NASA NTRS1993

Measurements in the near-field of a turbulent wingtip vortex

The roll-up of a wingtip vortex, at Reynold's number based on chord of 4.6 million, was examined with emphasis on suction side and near wake measurements. Surface oil flow and laser smoke flow studies are performed, demonstrating the highly 3D nature of the flow around the wingtip, the formation of the feeding sheet, and the viscous core region of the vortex. Flow visualization and correlation measurements show that meandering of the vortex is small and does not appreciably contribute to the turbulence measurements.

Chow, Jim S.↗

NASA NTRS1998

Oscillatory Thermocapillary Flow Experiment-2 (OTFE-2)

Oscillatory thermocapillary flow experiments were performed in the Glovebox aboard the USML-2 Spacelab which was launched on October 20, 1995. Open cylindrical containers of 1.2 and 2.0 cm in diameter were used. The ratio of container depth to radius (aspect ratio) was set at 0.5 and 2. Silicone oil of 2 centistokes kinematic viscosity was the test fluid. The fluid was heated by a cylindrical heater placed along the center axis of the container. The fluid motion was studied by flow visualization. The effect of aspect ratio on the onset of oscillations and on the oscillatory flow was investigated. It was found that the onset of oscillations was delayed when the container was made more shallow.

Kamotani, Yasuhiro↗

NASA NTRS2002

Flow Visualizations in a Packed Bed of Twisted Tapes

A videotape presentation of the flow field in a packed bed of 48 twisted tapes which can be simulated by very thin virtual cylinders has been assembled. The indices of refraction of the oil and the Lucite twisted tapes were closely matched, and the flow was seeded with magnesium oxide particles. Planar laser light projected the flow field in two dimensions both along and transverse to the flow axis. The flow field was three dimensional and complex to describe, yet the most prominent finding was flow threads. It appeared that axial flow spiraled along either within the confines of a virtual cylindrical boundary or within the exterior region, between the tangency points, of the virtual cylinders. Random packing and bed voids created vortices and disrupted the laminar flow but minimized the entrance effects. The flow-pressure drops in the packed bed fell below the Ergun model for porous-media flows. Single-twisted-tape results of Smithberg and Landis (1964) were used to guide the analysis. In appendix A the results of several investigators are scaled to the Ergun model. Further investigations including different geometric configurations, computational fluid dynamic (CFD) gridding, and analysis are required.

Hendricks, R. C.↗

NASA NTRS1989

Thermocapillary migration of liquid droplets in a temperature gradient in a density matched system

An experimental investigation of thermocapillary flow in droplets of a vegetable oil (partially hydrogenated soybean oil) immersed in silicone oil was conducted in a test cell with a heated top wall and a cooled bottom wall. The liquids are nearly immiscible and have equal densities at a temperature below the room temperature, thus providing a simulation of low-gravity conditions by reducing the buoyancy forces. The interfacial tension between the two oils was measured in the temperature range 20 to 50 C using a capillary tube and (d sigma)/(d T) was determined to be negative. Droplets ranging in sizes from 3 mm to 1 cm diameter were injected into the silicone oil. The vertical temperature profile in the bulk liquid (silicone oil) produces temperature variations along the interface which induce variations in the interfacial tension. The flow inside the droplet driven by the resulting interfacial shear stresses was observed using a laser light-sheet flow visualization technique. The flow direction is consistent with the sign of (d sigma)/(d T). The observed maximum surface velocities are compared to the theoretical predictions of Young et al. (1959).

Rashidnia, N.↗

NASA NTRS1991

Thermocapillary migration of liquid droplets in a temperature gradient in a density matched system

An experimental investigation of thermocapillary flow in droplets of a vegetable oil (partially hydrogenated soybean oil) immersed in silicone oil was conducted in a test cell with a heated top wall and a cooled bottom wall. The liquids are nearly immiscible and have equal densities at a temperature below the room temperature, thus providing a simulation of low-gravity conditions by reducing the buoyancy forces. The interfacial tension between the two oils was measured in the temperature range 20 to 50 C using a capillary tube and (d sigma)/(d T) was determined to be negative. Droplets ranging in sizes from 3 mm to 1 cm diameter were injected into the silicone oil. The vertical temperature profile in the bulk liquid (silicone oil) produces temperature variations along the interface which induce variations in the interfacial tension. The flow inside the droplet driven by the resulting interfacial shear stresses was observed using a laser light-sheet flow visualization technique. The flow direction is consistent with the sign of (d sigma)/(d T). The observed maximum surface velocities are compared to the theoretical predictions of Young et al. (1959).

Rashidnia, N.↗

NASA NTRS1989

Studies of vortex flow aerodynamics using CFD flow visualizations

Navier-Stokes computations of three-dimensional vortical flows over a round-edged double-delta wing and a tangent-ogive forebody are performed using an implicit upwind finite-difference scheme. Computed particle traces are compared with experimental oil-flow streaks.

Hsu, C.-H.↗

NASA NTRS1974

Results of flow visualization studies in the NASA/MSFC 14 x 14 inch trisonic wind tunnel on a .004 scale model (34-0) space shuttle orbiter and integrated vehicle

Details are presented of flow visualization techniques developed during wind tunnel test IA-52 conducted in a 14 x 14 inch trisonic wind tunnel. Testing was conducted from Mach = 0.9 to 5.0 on the orbiter alone and integrated vehicle configurations. Thin film oil paint and ultraviolet light sensitive oil applications were used on a .004 scale model vehicle. Test results presented are in the form of black and white photographs taken after the completion of a test run.

Garton, W. P.↗

NASA NTRS1990

Dye Tracing Of Flow On Forebody Of Airplane

Report describes experiments in which flows over forebody of F-18 airplane visualized by emitting liquid containing dye from orifices on forebody. In this method, liquid flows along body and evaporates, leaving behind lines of dye marking streamlines and photographed after test flight. Results similar to those of wind-tunnel oil flows.

Fisher, David F.↗

NASA NTRS1987

Engine flow visualization using a copper vapor laser

A flow visualization system has been developed to determine the air flow within the combustion chamber of a motored, axisymmetric engine. The engine has been equipped with a transparent quartz cylinder, allowing complete optical access to the chamber. A 40-Watt copper vapor laser is used as the light source. Its beam is focused down to a sheet approximately 1 mm thick. The light plane is passed through the combustion chamber, and illuminates oil particles which were entrained in the intake air. The light scattered off of the particles is recorded by a high speed rotating prism movie camera. A movie is then made showing the air flow within the combustion chamber for an entire four-stroke engine cycle. The system is synchronized so that a pulse generated by the camera triggers the laser's thyratron. The camera is run at 5,000 frames per second; the trigger drives one laser pulse per frame. This paper describes the optics used in the flow visualization system, the synchronization circuit, and presents results obtained from the movie. This is believed to be the first published study showing a planar observation of airflow in a four-stroke piston-cylinder assembly. These flow visualization results have been used to interpret flow velocity measurements previously obtained with a laser Doppler velocimetry system.

Regan, Carolyn A.↗

NASA NTRS1978

Flow field visualization about external axial corners

An experimental investigation was conducted to visualize the flow field about external axial corners. The investigation was initiated to provide answers to questions about the inviscid flow pattern for continuing numerical investigations. Symmetrical and asymmetrical corner models were tested at a Reynolds number per meter of 60,700,000. Oil-flow and vapor-screen photographs were taken for both models at angle of attack and yaw. The paper presents the results of the investigation in the form of oil-flow photographs and the surrounding shock wave location obtained from the vapor screens.

Talcott, N. A., Jr.↗

NASA NTRS1985

Separation bubble behavior for a NACA 23009 airfoil

Results are reported of experiments with smoke-wire flow visualization applied to characterizing the conditions conducive to formation of a separation bubble on an airfoil in low Re flow. An airfoil was used which spanned the test channel of the wind tunnel designed for low turbulence and noise. A wire coated with mineral oil was stretched across the channel upstream of the airfoil and heated. The smoke it gave off was flash-illuminated and photographed with ASA 3000 film. Extending the airfoil over the entire section yielded photographs that gave an essentially two-dimensional perspective. Angles of attack from 0-10 deg were investigated at Re of 33,000, 66,000, 100,000 and 133,000. Sample photographs illustrate the usefulness of the technique and apparatus in the flow regimes examined, particularly when used in conjunction with pressure tap data from the airfoil surface.

Fisher, S. S.↗

NASA NTRS1994

Oscillatory Thermocapillary Flow Experiment (OTFE)

An experiment was performed on oscillatory thermocapillary flow in the Glovebox aboard the USML-1 Spacelab which was launched in July, 1992. Cylindrical containers of 1 and 3 em in diameter were used. Silicone oils of 2 and 5 cSt viscosity were the test fluids. The fluid was heated by a cylindrical heater placed along the centerline of the container. The diameter of the heater was 10% of the container diameter. The fluid motion was studied by flow visualization. Although oscillations were observed briefly, bubbles generated in the fluid during the experiment disturbed the flow substantially so that the critical temperature differences could not be determined.

Kamotani, Y.↗

NASA NTRS1994

Surface Tension Driven Convection Experiment (STDCE)

Results are reported of the Surface Tension Driven Convection Experiment (STDCE) aboard the USML-1 (first United States Microgravity Laboratory) Spacelab which was launched on June 25, 1992. In the experiment 10 cSt silicone oil was placed in an open circular container which was 10 cm wide by 5 cm deep. The fluid was heated either by a cylindrical heater (1.11 cm dia.) located along the container centerline or by a CO2 laser beam to induce thermocapillary flow. The flow field was studied by flow visualization. Several thermistor probes were placed in the fluid to measure the temperature distribution. The temperature distribution along the liquid free surface was measured by an infrared imager. Tests were conducted over a range of heating powers, laser beam diameters, and free surface shapes. In conjunction with the experiments an extensive numerical modeling of the flow was conducted. In this paper some results of the velocity and temperature measurements with flat and curved free surfaces are presented and they are shown to agree well with the numerical predictions.

Ostrach, Simon↗

NASA NTRS1991

An experimental comparison of nonswirling and swirling flow in a circular-to-rectangular transition duct

Circular-to-rectangular transition duct flows with and without inlet swirl were investigated experimentally in order to determine the effect of inlet swirl on the transition duct flow field and to provide detailed duct flow data for comparison with numerical code predictions. Coefficients based on detailed measurements of velocity, total pressure and static pressure, acquired in four cross stream planes within a circular-to-rectangular transition duct, with and without inlet swirl, are presented, as are surface static pressure and surface oil film visualization results.

Reichert, B. A.↗

NASA NTRS1987

Measurement of the effect of manufacturing deviations on natural laminar flow for a single engine general aviation airplane

Renewed interest in natural laminar flow (NLF) had rekindled designer concern that manufacuring deviations may destroy the effectiveness of NLF for an operational aircraft. Experiments are summarized that attemtped to measure total drag changes associated with three different wing surface conditions on an aircraft typical of current general aviation high performance singles. The speed power technique was first used in an attempt to quantify the changes in total drag. Predicted and measured boundary layer transition locations for three different wing surface conditions were also compared, using two different forms of flow visualization. The three flight test phases included: assessment of an unpainted airframe, flight tests of the same aircraft after painstakingly filling and sanding the wings to design contours, and similar measurement after this aricraft was painted. In each flight phase, transition locations were monitored using with sublimating chemicals or pigmented oil. Two-dimensional drag coefficients were estimated using the Eppler-Somers code and measured with a wake rake in a method very similar to Jones' pitot traverse method. The net change in two-dimensional drag coefficient was approximately 20 counts between the unpainted aircraft and the hand-smoothed aircraft for typical cruise flight conditions.

Source record↗

NASA NTRS1992

Test description and preliminary pitot-pressure surveys for Langley Test Technique Demonstrator at Mach 6

A propulsion/airframe integration experiment conducted in the NASA Langley 20-Inch Mach 6 Tunnel using a 16.8-in.-long version of the Langley Test Technique Demonstrator configuration with simulated scramjet propulsion is described. Schlieren and vapor screen visualization of the nozzle flow field is presented and correlated with pitot-pressure flow-field surveys. The data were obtained at nominal free-stream conditions of Re = 2.8 x 10 exp 6 and a nominal engine total pressure of 100 psia. It is concluded that pitot-pressure surveys coupled to schlieren and vapor-screen photographs, and oil flows have revealed flow features including vortices, free shear layers, and shock waves occurring in the model flow field.

Everhart, Joel L.↗

DOE OSTI2022

A level set approach for the computational study of a yield stress fluid filling a thin mold

Many important engineering and scientific applications such as cement slurries, foams, crude oil, and granular avalanches involve the concept of yield stress. Therefore, modeling yield stress fluids in different flow configurations, including the accurate prediction of the yield surface, is important. In this paper, we present a computational model based on the finite element method to study the flow of yield stress fluids in a thin mold and compare the results with data from flow visualization experiments. Here, we use the level set method to describe the interface between the filling fluid and air. We use polypropylene glycol as a model Newtonian fluid and Carbopol for the model yield stress fluid, as the Carbopol solution demonstrates yielding without thixotropy. To describe the yielding and shear-thinning behavior, we use a generalized Newtonian constitutive equation with a Bingham–Carreau–Yasuda form. We compare the results obtained from the mold filling experiments with the results from the three-dimensional (3D) model and from a reduced-order Hele-Shaw (HS) model that is two-dimensional, including the effect of shear-thinning along the thin direction only approximately. We show that both the 3D and the HS model can capture the experimental meniscus shape reasonably well for all the fluids considered at three different flow rates. This indicates that the shape evolution is insensitive to the dimensionality of the model. However, the viscosity and yield surfaces predicted by the 3D and HS models are different. The HS model underestimates the high viscosity and unyielded regions compared to the estimation by the 3D model.

42 ENGINEERING↗