Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - BUCKLING, SHEAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Experimental Investigation of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the y pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. The main emphasis in this paper is placed on flow field surveys performed at a y Reynolds number of 100,000 with levels of freestream turbulence ranging from 0.8% to 3%. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗
NASA NTRS1987

The growth and breakdown of streamwise vortices in the presence of a wall

The growth and breakdown of counter-rotating streamwise vortices, generated on a concave wall via the Goertler instability mechanism, were experimentally studied as a model for comparable eddy structures that exist in transitional and turbulent flat-plate boundary layers. The experiments were conducted in a low-speed open-return wind tunnel, using smoke-wire visualization and multiple-probe hot wires to study the vortices. As low-momentum fluid was removed from the wall, low-speed regions formed between the vortices; these regions grew in the normal direction faster than a nominally Blasius boundary layer and created strongly inflexional normal and spanwise profiles of the streamwise velocity component. Instability oscillations developed on these unstable profiles that scaled with the local shear-layer thickness and velocity difference. The spatial scales of the temporal velocity fluctuations were found to correlate with the velocity gradient in the spanwise (rather than in the normal) direction.

Swearingen, Jerry D.↗
NASA NTRS1987

Turbulence control on an airborne laser platform

An active flow control device to generate large-scale, periodic structures in a turbulent shear flow is developed. Together with adaptive optics, the device may be used on airborne laser platforms to reduce or eliminate optical distortion caused by the turbulence in the aircraft's boundary layer. A cyclic jet issuing from a spanwise slot is used to collect the turbulent boundary layer for a finite time and then release all of the flow instantaneously in one large eddy that convects downstream. Flow visualization and hot-film probe measurements are used together with pattern recognition algorithms to demonstrate the viability of the flow control method. A flat plate towed in a water channel is used as a test bed. The instantaneous velocity signal is used to compute important statistical quantities of the random velocity field, such as the mean, the root-mean-square, the spectral distribution, and the probability density function. When optimized for a given boundary layer, it is shown that the cyclic jet will produce periodic structures that are similar to the random, naturally occurring ones. These structures seem to trigger the onset of bursting events near the wall of the plate. Thus, the present device generates periodic structures in both the outer and inner regions of a turbulent boundary layer.

Gad-El-hak, Mohamed↗
NASA NTRS1998

Experimental Study of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. Freestream turbulence levels ranging from 0.8% to 3% was used in this experiment. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. Hot-wires (single and x-wire) and surface mounted hot-film gases and static pressure taps were used to map the flowfield. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗
NASA NTRS1989

Free-molecule-flow force and moment coefficients of the aeroassist flight experiment vehicle

Calculated results for the aerodynamic coefficients over the range of + or - 90 deg in both pitch and yaw attitude angles for the Aeroassist Flight Experiment (AFE) vehicle in free molecule flow are presented. The AFE body is described by a large number of small flat plate surface elements whose orientations are established in a wind axes coordinate system through the pitch and yaw attitude angles. Lift force, drag force, and three components of aerodynamic moment about a specified point are computed for each element. The elemental forces and moments are integrated over the entire body, and total force and moment coefficients are computed. The coefficients are calculated for the two limiting gas-surface molecular collision conditions, namely, specular and diffuse, which assume zero and full thermal accommodation of the incoming gas molecules with the surface, respectively. The individual contribution of the shear stress and pressure terms are calculated and also presented.

Blanchard, Robert C.↗
NASA NTRS1994

Skin friction measurement in complex flows using thin oil film techniques

The NASA Grant NAG2-261 was initiated to support a program of research to study complex flows that occur in flight and laboratory experiments by building, testing and optimizing an on-board technique for direct measurement of surface shear stress using thin oil film techniques. The program of research has proceeded under the supervision of the NASA Ames Research Center and with further cooperation from the NASA Ames-Dryden and NASA Langley Research Centers. In accordance with the original statement of work, the following research milestones were accomplished: (1) design and testing of an internally mounted one-directional skin friction meter to demonstrate the feasibility of the concept; (2) design and construction of a compact instrument capable of measuring skin friction in two directions; (3) study of transitional and fully turbulent boundary layers over a flat plate with and without longitudinal pressure gradients utilizing the compact two-directional skin friction meter; (4) study of the interaction between a turbulent boundary layer and a shock wave generated by a compression corner using the two-directional meter; and (5) flight qualification of the compact meter and accompanying electronic and pneumatic systems, preliminary installation into flight test fixture.

Source record↗
NASA NTRS2001

Design of Fiber Optic Sensors for Measuring Hydrodynamic Parameters

The science of optical hydrodynamics involves relating the optical properties to the fluid dynamic properties of a hydrodynamic system. Fiber-optic sensors are being designed for measuring the hydrodynamic parameters of various systems. As a flowing fluid makes an encounter with a flat surface, it forms a boundary layer near this surface. The region between the boundary layer and the flat plate contains information about parameters such as viscosity, compressibility, pressure, density, and velocity. An analytical model has been developed for examining the hydrodynamic parameters near the surface of a fiber-optic sensor. An analysis of the conservation of momentum, the continuity equation and the Navier-Stokes equation for compressible flow were used to develop expressions for the velocity and the density as a function of the distance along the flow and above the surface. When examining the flow near the surface, these expressions are used to estimate the sensitivity required to perform direct optical measurements and to derive the shear force for indirect optical measurements. The derivation of this result permits the incorporation of better design parameters for other fiber-based sensors. Future work includes analyzing the optical parametric designs of fiber-optic sensors, modeling sensors to utilize the parameters for hydrodynamics and applying different mixtures of hydrodynamic flow. Finally, the fabrication of fiber-optic sensors for hydrodynamic flow applications of the type described in this presentation could enhance aerospace, submarine, and medical technology.

Lyons, Donald R.↗
NASA NTRS1986

Ultrasonic level sensors for liquids under high pressure

An ultrasonic level sensor of novel design continuously measures the level of a liquid subjected to a high pressure (up to about 40 MPa), as is sometimes required for the effective transfer of the liquid. The sensor operates as a composite resonator fabricated from a standard high-pressure plug. A flat-bottom hole is machined into the plug along its center line. An ultrasonic transducer is bonded rigidly to the interior surface of the bottom wall, while the exterior surface is in contact with the liquid. Although the bottom wall is designed to satisfy the pressure code, it is still sufficiently thin to permit ready excitation of the axisymmetric plate modes of vibration. The liquid level is measured by a conventional pulse-echo technique. A prototype sensor was tested successfully in a 2300-l water vessel at pressures up to about 37 MPa. A spectral analysis of the transmitted pulse reveals that the flexural, extensional, thickness-shear, and radial plate modes are excited into vibration, but none of these appears to be significantly affected by the pressurization of the liquid.

Zuckerwar, A. J.↗
NASA NTRS1959

Use of a Stanton Tube for Skin-Friction Measurements

A small total-pressure tube resting against a flat-plate surface was used as a Stanton tube and calibrated as a skin-friction meter at various subsonic and supersonic speeds. Laminar flow was maintained for the supersonic runs at a Mach number M(sub infinity) of 2. At speeds between M(sub infinity) = 1.33 and M(sub infinity) = 1.87, the calibrations were carried-out in a turbulent boundary layer. The subsonic flows were found to be in transition. The skin-friction readings of a floating-element type of balance served as the reference values against which the Stanton tube was calibrated. A theoretical model was developed which, for moderate values of the shear parameter tau, accurately predicts the performance of the Stanton tube in subsonic and supersonic flows. A "shear correction factor" was found to explain the deviations from the basic model when T became too large. Compressibility effects were important only in the case of turbulent supersonic flows, and they did not alter the form of the calibration curve. The test Reynolds numbers, based on the distance from the leading edge and free-stream conditions, ranged from 70,000 to 875,000. The turbulent-boundary-layer Reynolds numbers, based on momentum thickness, varied between 650 and 2,300. Both laminar and turbulent velocity profiles were taken and the effect of pressure gradient on the calibration was investigated.

Abarbanel, S. S.↗
NASA NTRS1998

A New View of the Dynamics of Reynolds Stress Generation in Turbulent Boundary Layers

The structure of a numerically simulated turbulent boundary layer over a flat plate at Re(theta) = 670 was studied using the invariants of the velocity gradient tensor (Q and R) and a related scalar quantity, the cubic discriminant (D = 27R(exp 2)/4 + Q(exp 3)). These invariants have previously been used to study the properties of the small-scale motions responsible for the dissipation of turbulent kinetic energy. In addition, these scalar quantities allow the local flow patterns to be unambiguously classified according to the terminology proposed by Chong et al. The use of the discriminant as a marker of coherent motions reveals complex, large-scale flow structures that are shown to be associated with the generation of Reynolds shear stress -u'v'(bar). These motions are characterized by high spatial gradients of the discriminant and are believed to be an important part of the mechanism that sustains turbulence in the near-wall region.

Cantwell, Brian J.↗
NASA NTRS2018

Intermittency and Cessation of Vortex Shedding in the Wake of a Thin Flat Plate with a Circular Trailing Edge

The near and very near wake of thin flat plates with both sharp and circular trailing edges (TEs) are investigated with direct numerical simulations (DNSs). The TE is circular in two of the cases (IN & NS) and sharp in one of them (ST). The separating boundary layers are turbulent in all cases. The objectives of this study are twofold. The first is to explore the effect of significantly reducing Re(sub D) (Reynolds number based on circular TE diameter, D) on the flow in the TE region, and the shedding process (Cases IN and NS). The second is to better understand the reasons underlying the findings of an earlier experimental wake investigation (sharp TE) where (1) the center-line values in normal intensity, and the peak in shear stress profiles in the cross-stream direction, were found to first increase in the streamwise direction (x), from that obtained at the TE, before diminishing further downstream, and (2) a broadband peak was observed in centerline cross-stream velocity (v) spectra (indicating quasi-periodicity, possibly due to vortices or wave-like motions). Case ST from the present study showed a near wake instability resulting in spanwise vortices (with a streamwise component). The instability is intermittent and contributes to both the broadband peak in the v spectrum and the initial increases in normal intensity and shear stress (as in the experiment). Case NS, with the lower value of ReD is an "essentially" non-shedding case where the flow in the TE region continually changes direction (upward/downward) because of turbulence. Case IN, with twice the value of ReD as Case NS, also exhibits a swaying motion in the TE region. In addition, vortex shedding is initiated during periods when the flow direction changes rapidly. Shedding in this case is intermittent. It results in a peak in the v spectrum obtained at the centerline (x/D = 1.0).

direct numerical simulations↗
NASA NTRS2020

Mechanisms of Stationary Crossflow Instability Growth and Breakdown Induced by Forward-Facing Steps

An experimental study is performed to determine the mechanisms by which a forward-facing step impacts the growth and breakdown to turbulence of the stationary cross-flow instability. Particle image velocimetry measurements are obtained in the boundary layer of a 30◦swept flat plate with a pressure body. Step heights range from 53 % to 71 % of the boundary-layer thickness. The critical step height is approximately 60 % of the boundary-layer thickness for the current study, although it is also shown that the critical step height depends on the initial amplitude of the stationary cross-flow vortices. For the critical cases, the stationary cross-flow amplitude grows sharply downstream of the step, decays for a short region and then grows again. The initial growth region is linear, and can be explained primarily through the impact of the step on the mean flow. Namely, the step causes abrupt changes to the mean flow, resulting in large values of wall-normal shear, as well as highly inflectional profiles, due to either cross-flow reversal, separation or both. These inflectional profiles are highly unstable for the stationary cross-flow. Additionally,the reversed flow regions are significantly modulated by the stationary cross-flow vortices. The second region of growth occurs due to the stationary-cross-flow-induced modulation of the shear layer, which leads to multiple smaller wavelength stream wise vortices. High-frequency fluctuations indicate that the unsteady transition mechanism for the critical cases relates to the shedding of vortices downstream of reattachment of the modulated separated regions.

boundary layer stability↗
NASA NTRS2003

Boundary-Layer Separation Control under Low-Pressure Turbine Airfoil Conditions using Glow-Discharge Plasma Actuators

Modem low-pressure turbines, in general, utilize highly loaded airfoils in an effort to improve efficiency and to lower the number of airfoils needed. Typically, the airfoil boundary layers are turbulent and fully attached at takeoff conditions, whereas a substantial fraction of the boundary layers on the airfoils may be transitional at cruise conditions due to the change of density with altitude. The strong adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation at the latter low Reynolds number conditions. Large separation bubbles, particularly those which fail to reattach, cause a significant degradation of engine efficiency. A component efficiency drop of the order 2% may occur between takeoff and cruise conditions for large commercial transport engines and could be as large as 7% for smaller engines at higher altitude. An efficient means of of separation elimination/reduction is, therefore, crucial to improved turbine design. Because the large change in the Reynolds number from takeoff to cruise leads to a distinct change in the airfoil flow physics, a separation control strategy intended for cruise conditions will need to be carefully constructed so as to incur minimum impact/penalty at takeoff. A complicating factor, but also a potential advantage in the quest for an efficient strategy, is the intricate interplay between separation and transition for the situation at hand. Volino gives a comprehensive discussion of several recent studies on transition and separation under low-pressure-turbine conditions, among them one in the present facility. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions. If the transition occurs early in the boundary layer then separation may be reduced or completely eliminated. Transition in the shear layer of a separation bubble can lead to rapid reattachment. This suggests using control mechanisms to trigger and enhance early transition. Gad-el-Hak provides a review of various techniques for flow control in general and Volino discusses recent studies on separation control under low-pressure-turbine conditions utilizing passive as well as active devices. As pointed out by Volino, passive devices optimized for separation control at low Reynolds numbers tend to increase losses at high Reynolds numbers, Active devices have the attractive feature that they can be utilized only in operational regimes where they are needed and when turned off would not affect the flow. The focus in the present paper is an experimental Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modem low-pressure-turbine airfoil ('Pak-B'). The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2%) and high (2.5%) Gee-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface- flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control. of active separation control using glow discharge plasma actuators.

Hultgren, Lennart S.↗
NASA NTRS1998

The NASA Low-Pressure Turbine Flow Physics Program

An overview of the NASA Lewis Low-Pressure Turbine (LPT) Flow Physics Program will be presented. The program was established in response to the aero-engine industry's need for improved LPT efficiency and designs. Modern jet engines have four to seven LPT stages, significantly contributing to engine weight. In addition, there is a significant efficiency degradation between takeoff and cruise conditions, of up to 2 points. Reducing the weight and part count of the LPT and minimizing the efficiency degradation will translate into fuel savings. Accurate prediction methods of LPT flows and losses are needed to accomplish those improvements. The flow in LPT passages is at low Reynolds number, and is dominated by interplay of three basic mechanisms: transition, separation and wake interaction. The affecting parameters traditionally considered are Reynolds number, freestream turbulence intensity, wake frequency parameter, and the pressure distribution (loading). Three-dimensional effects and additional parameters, particularly turbulence characteristics like length scales, spectra and other statistics, as well as wake turbulence intensity and properties also play a role. The flow of most interest is on the suction surface, where large losses are generated as the flow tends to separate at the low Reynolds numbers. Ignoring wakes, a common flow scenario, there is laminar separation, followed by transition on the separation bubble and turbulent reattachment. If transition starts earlier the separation will be eliminated and the boundary layer will be attached leading to the well known bypass transition issues. In contrast, transition over a separation bubble is closer to free shear layer transition and was not investigated as well, particularly in the turbine environment. Unsteadiness created by wakes complicates the picture. Wakes induce earlier transition, and the calmed regions trailing the induced turbulent spots can delay or eliminate separation via shear stress modification. Three-dimensional flow physics and geometry will have strong effects. Altogether a very complex and challenging problem emerges. The objective of the program is to provide improved models and physical understanding of the complex flow, which are essential for accurate prediction of flow and losses in the LPT. Experimental, computational and analytical work as complementing and augmenting approaches are used. The program involves industry, universities and research institutes, and other government laboratories. It is characterized by strong interaction among participants, quick dissemination of results, and responsiveness to industry's needs. The presentation will describe the work elements. Highlighting some activities in progress are experiments on simulated blade suction surface in low-speed wind tunnels, on curved wall, and on a flat-plate, both with pressure gradient. In the area of computation, assessment of existing models is performed using RANS (Reynolds Averaged Navier Stokes) simulations. Laminar flow DNS was completed. Analytical studies of instability and receptivity in attached and separated flows were started. In the near future the program is moving to include wake effects and development of improved modeling. Experimental work in preparation stages are: (1) Addition of wakes to the curved tunnel experiment; (2) Low-speed rotating rig experiment on GE90 engine LPT; and (3) Transonic cascade. In the area of computation, it is expected to move from model assessment towards development of improved models. In addition, a new project of Large Eddy Simulation (LES) of LPT is to begin and will provide numerical data bases. It is planned to implement the emerging improved models in a multistage turbomachinery code and to validate against the GE90 engine LPT.

Ashpis, David E.↗
NASA NTRS2019

Nonlinear Görtler Vortices and Their Secondary Instability in a Hypersonic Boundary Layer

Nonlinear development of the Görtler instability over a concave surface gives rise to a highly distorted inflectional flow field in the boundary layer that leads to both wall-normal and spanwise gradients in the flow. Such nonlinear structures are susceptible to strong, high-frequency secondary instabilities that may lead to the onset of laminar-turbulent transition. The present numerical study uses direct numerical simulations and linear secondary instability theory to investigate finite amplitude Görtler vortices and their secondary instability characteristics, respectively, in the hypersonic flow over an axisymmetric cone with a concave aft body. To complement previous studies in the literature wherein the Görtler instability was usually studied for a flat plate and initiated at some upstream location by imposing an eigenfunction as the inflow condition or by blowing and suction at the wall, the present investigation is focused on fully realizable Görtler instability that is excited by an azimuthally periodic array of surface protuberances. Furthermore, while the previous work had mostly focused on the secondary instability of Görtler vortices with cross-plane velocity contours that resembled bell-shaped structures, the present results confirm that fully developed mushroom structures also exist in the hypersonic regime when the Görtler vortex amplitude is sufficiently large. Computations further reveal that the dominant modes of secondary instability in these mushroom-shaped structures correspond to an antisymmetic (i.e., sinuous) “stem” mode that concentrates within the strong, nearly wall-normal internal shear layers surrounding the stem regions underneath the caps of the mushroom structures. Additionally, there exist a multitude of other significantly unstable secondary instability modes of both symmetric and antisymmetric types. Analogous to the secondary instability of crossflow vortices in hypersonic flows, secondary instability modes of both symmetric and antisymmetric types. Analogous to the secondary instability of crossflow vortices in hypersonic flows, secondary instability modes originating from the Mack mode instability play an important role during the nonlinear breakdown process.

Laminar turbulent transition↗
NASA NTRS1991

Free-stream turbulence and concave curvature effects on heated, transitional boundary layers

An experimental investigation of the transition process on flat-plate and concave curved-wall boundary layers for various free-stream turbulence levels was performed. Results show that for transition of a flat-plate, the two forms of boundary layer behavior, identified as laminar-like and turbulent-like, cannot be thought of as separate Blasius and fully-turbulent profiles, respectively. Thus, simple transition models in which the desired quantity is assumed to be an average, weighted on intermittency, of the theoretical laminar and fully turbulent values is not expected to be successful. Deviation of the flow identified as laminar-like from theoretical laminar behavior is shown to be due to recovery after the passage of a turbulent spot, while deviation of the flow identified as turbulent-like from the full-turbulent values is thought to be due to incomplete establishment of the fully-turbulent power spectral distribution. Turbulent Prandtl numbers for the transitional flow, computed from measured shear stress, turbulent heat flux and mean velocity and temperature profiles, were less than unity. For the curved-wall case with low free-stream turbulence intensity, the existence of Gortler vortices on the concave wall within both laminar and turbulent flows was established using liquid crystal visualization and spanwise velocity and temperature traverses. Transition was found to occur via a vortex breakdown mode. The vortex wavelength was quite irregular in both the laminar and turbulent flows, but the vortices were stable in time and space. The upwash was found to be more unstable, with higher levels of u' and u'v', and lower skin friction coefficients and shape factors. Turbulent Prandtl numbers, measured using a triple-wire probe, were found to be near unity for all post-transitional profiles, indicating no gross violation of Reynolds analogy. No evidence of streamwise vortices was seen in the high turbulence intensity case.

Kim, J.↗
NASA NTRS2019

The Intermediate Wake of a Thin Flat Plate with a Circular Trailing Edge

The intermediate wakes of thin flat plates with circular trailing edges (TEs) are investigated here with direct numerical simulations (DNSs). The separating boundary layers are turbulent in all cases. The near wake in two thin-plate cases (IN & NS), with a focus on the vortex shedding process, was explored in a recent article. Intermittent shedding was observed in Case IN. Case NS, with half the TE diameter of Case IN, was an essentially non-shedding case. A third case (ST) with a sharp trailing edge was also investigated and found to exhibit an intermittent wake instability. The objectives of the present study are twofold. The first is to determine if the wake instability found in Case ST exists in Cases IN and NS as well. The second is to provide the distributions of the turbulent normal intensities and shear stress in the wake and to understand these distributions via the budget terms in the corresponding transport equations. The results show that both Cases IN & NS exhibit a wake instability in the intermediate wake region, that is similar to that found earlier in Case ST. We note that in Case IN, the presence of an intermediate-wake instability results in the co-existence of two different types of instability within a single wake. The distributions of the turbulent normal intensities and shear stress, and the budget terms for the streamwise intensity are included and discussed here. All the budget terms contribute appreciably to the overall budget in the transport equation for streamwise normal intensity.

Rai, Man Mohan↗
NASA NTRS1989

An experimental study of near wall flow parameters in the blade end-wall corner region

The near wall flow parameters in the blade end-wall corner region is investigated. The blade end-wall corner region was simulated by mounting an airfoil section (NACA 65-015 base profile) symmetric blades on both sides of the flat plate with semi-circular leading edge. The initial 7 cm from the leading edge of the flat plate was roughened by gluing No. 4 floor sanding paper to artificially increase the boundary layer thickness on the flat plate. The initial flow conditions of the boundary layer upstream of the corner region are expected to dictate the behavior of flow inside the corner region. Therefore, an experimental investigation was extended to study the combined effect of initial roughness and increased level of free stream turbulence on the development of a 2-D turbulent boundary layer in the absence of the blade. The measurement techniques employed in the present investigation included, the conventional pitot and pitot-static probes, wall taps, the Preston tube, piezoresistive transducer and the normal sensor hot-wire probe. The pitot and pitot-static probes were used to obtain mean velocity profile measurements within the boundary layer. The measurements of mean surface static pressure were obtained with the surface static tube and the conventional wall tap method. The wall shear vector measurements were made with a specially constructed Preston tube. The flush mounted piezoresistive type pressure transducer were employed to measure the wall pressure fluctuation field. The velocity fluctuation measurements, used in obtaining the wall pressure-velocity correlation data, were made with normal single sensor hot-wire probe. At different streamwise stations, in the blade end-wall corner region, the mean values of surface static pressure varied more on the end-wall surface in the corner region were mainly caused by the changes in the curvature of the streamlines. The magnitude of the wall shear stress in the blade end-wall corner region increased significantly in the close vicinity of the corner line. The maximum value of the wall shear stress and its location from the corner line, on both the surfaces forming the corner region, were observed to change along the corner. These observed changes in the maximum values of the wall shear stress and its location from the corner line could be associated with the stretching and attenuation of the horseshoe vortex. The wall shear stress vectors in the blade end-wall corner region were observed to be more skewed on the end-wall surface as compared to that on the blade surface. The differences in the wall shear stress directions obtained with the Preston tube and flow visualization method were within the range in which the Preston tube was found to be insensitive to the yaw angle.

Bhargava, Rakesh K.↗