Search NASA⌕ Search

SEARCH · Search NASA

Results for “Passive Mitigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

213 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Kinematic Sensors Evaluation for Spaceflight Exercise Data Collections

INTRODUCTION: On the International Space Station (ISS), exercise feedback from astronauts is very important to diagnose and mitigate any form-related injuries and ensure efficacious exercise prescriptions and systems. Going forward, exploration exercise efforts seek to gain further quantitative data of human and system performance. Currently, methods of collecting in-flight exercise data on the ISS are limited to marker-based motion capture (MoCap) where astronauts must wear reflective markers over their clothes and specialized cameras are used. The main objective of this work was to investigate the following alternative tracking options: markerless video-based MoCap and inertial measurement units (IMUs). These were compared against traditional marker-based MoCap to evaluate kinematic accuracy and inform feasible methods for future exercise data collections on the ISS, especially in support of future Vibration Isolation and Stabilization (VIS) system development. METHODS: Three test subjects performed a variety of flight-like resistance and aerobic exercises using the Miniature Exercise Device (MED-2), Concept-2 rowing ergometer, barbell mockup, bench (e.g., for bench press, hip thruster, and cycling), and a custom structure for dips. These were intended also to represent exercises which could be performed on the multi-modality European Enhanced Exploration Exercise Device (E4D) [1]. The marker-based MoCap data, collected through a 16-camera OptiTrack MoCap system, was regarded as the gold standard to compare the data against. Passive markers were affixed to each subject according to a modified full body Plug-in Gait marker set [2] with 46 total markers. The markerless MoCap data was collected using two GoPro Hero7 cameras and one GoPro Hero11 camera. For the IMU data, a full body set of 17 Xsens DOTs were placed on the subject: 10 upper body and 7 lower body IMUs. Biomechanical modeling and evaluation was conducted through OpenSim [3] (MoCap), OpenSense [4] (IMU), OpenCap [5] (markerless), ENABLE [6] (markerless), and other modeling software. Secondary objectives included comparing the volume of equipment, reducing mass and crew set-up time. RESULTS AND DISCUSSION: While there were issues with initial processing for the IMUs and markerless MoCap, the results aided in the understanding of each sensor, developing end-to-end processes, and identifying future needs. Some observed concerns with the markerless MoCap approaches included being cognizant of a cluttered background, number of people in field of view, camera number and placement. Some challenges with the IMUs included possible sliding, early deactivation possibly due to exercise pose, and large quantity sensor synchronization. Overall, the markerless MoCap option may be the preferred method of data collection and processing as it provides a solution for certain IMU shortcomings and may be least in equipment volume, upmass, and crew setup time. CONCLUSIONS: While this work was mainly focused on ISS data collection, these sensor data along with continued evaluation and development efforts will help to establish best methods for exercise data collection on Gateway, for other Artemis missions, and beyond. Details on the latest end-to-end processing of the data and results will be presented, along with lessons learned and recommended sensor selection and methods.

S. Faragalla↗
NASA NTRS2024

Kinematic Sensors Evaluation for Spaceflight Exercise Data Collections

INTRODUCTION: On the International Space Station (ISS), exercise feedback from astronauts is very important to diagnose and mitigate any form-related injuries and ensure efficacious exercise prescriptions and systems. Going forward, exploration exercise efforts seek to gain further quantitative data of human and system performance. Currently, methods of collecting in-flight exercise data on the ISS are limited to marker-based motion capture (MoCap) where astronauts must wear reflective markers over their clothes and specialized cameras are used. The main objective of this work was to investigate the following alternative tracking options: markerless video-based MoCap and inertial measurement units (IMUs). These were compared against traditional marker-based MoCap to evaluate kinematic accuracy and inform feasible methods for future exercise data collections on the ISS, especially in support of future Vibration Isolation and Stabilization (VIS) system development. METHODS: Three test subjects performed a variety of flight-like resistance and aerobic exercises using the Miniature Exercise Device (MED-2), Concept-2 rowing ergometer, barbell mockup, bench (e.g., for bench press, hip thruster, and cycling), and a custom structure for dips. These were intended also to represent exercises which could be performed on the multi-modality European Enhanced Exploration Exercise Device (E4D) [1]. The marker-based MoCap data, collected through a 16-camera OptiTrack MoCap system, was regarded as the gold standard to compare the data against. Passive markers were affixed to each subject according to a modified full body Plug-in Gait marker set [2] with 46 total markers. The markerless MoCap data was collected using two GoPro Hero7 cameras and one GoPro Hero11 camera. For the IMU data, a full body set of 17 Xsens DOTs were placed on the subject: 10 upper body and 7 lower body IMUs. Biomechanical modeling and evaluation was conducted through OpenSim [3] (MoCap), OpenSense [4] (IMU), OpenCap [5] (markerless), ENABLE [6] (markerless), and other modeling software. Secondary objectives included comparing the volume of equipment, reducing mass and crew set-up time. RESULTS AND DISCUSSION: While there were issues with initial processing for the IMUs and markerless MoCap, the results aided in the understanding of each sensor, developing end-to-end processes, and identifying future needs. Some observed concerns with the markerless MoCap approaches included being cognizant of a cluttered background, number of people in field of view, camera number and placement. Some challenges with the IMUs included possible sliding, early deactivation possibly due to exercise pose, and large quantity sensor synchronization. Overall, the markerless MoCap option may be the preferred method of data collection and processing as it provides a solution for certain IMU shortcomings and may be least in equipment volume, upmass, and crew setup time. CONCLUSIONS: While this work was mainly focused on ISS data collection, these sensor data along with continued evaluation and development efforts will help to establish best methods for exercise data collection on Gateway, for other Artemis missions, and beyond. Details on the latest end-to-end processing of the data and results will be presented, along with lessons learned and recommended sensor selection and methods.

S Faragalla↗
NASA NTRS1997

Studies of the Interactions Between Vestibular Function and Tactual Orientation Display Systems

When humans experience conditions in which internal vestibular cues to movement or spatial location are challenged or contradicted by external visual information, the result can be spatial disorientation, often leading to motion sickness. Spatial disorientation can occur in any situation in which the individual is passively moved in the environment, but is most common in automotive, aircraft, or undersea travel. Significantly, the incidence of motion sickness in space travel is great: The majority of individuals in Shuttle operations suffer from the syndrome. Even after the space-sickness-producing influences of spatial disorientation dissipate, usually within several days, there are other situations in which, because of the absence of reliable or familiar vestibular cues, individuals in space still experience disorientation, resulting in a reliance on the already preoccupied sense of vision. One possible technique to minimize the deleterious effects of spatial disorientation might be to present attitude information (including orientation, direction, and motion) through another less-used sensory modality - the sense of touch. Data from experiences with deaf and blind persons indicate that this channel can provide useful communication and mobility information on a real-time basis. More recently, technologies have developed to present effective attitude information to pilots in situations in which dangerously ambiguous and conflicting visual and vestibular sensations occur. This summers project at NASA-Johnson Space Center will evaluate the influence of motion-based spatial disorientation on the perception of tactual stimuli representing veridical position and orientation information, presented by new dynamic vibrotactile array display technologies. In addition, the possibility will be explored that tactile presentations of motion and direction from this alternative modality might be useful in mitigating or alleviating spatial disorientation produced by multi-axis rotatory systems, monitored by physiological recording techniques developed at JSC.

Cholewiak, Roger W.↗
NASA NTRS2018

Cryogenic Selective Surfaces

There are many challenges involved in deep-space exploration, but several of these can be mitigated, or even solved, by the development of a coating that reflects most of the Sun’s energy, yet still provides far-infrared heat emission. Such a coating would allow non-heat-generating objects in space to reach cryogenic temperatures without using an active cooling system. This would benefit deep-space sensors that require low temperatures, such as the James Webb Telescope focal plane array. It would also allow the use of superconductors in deep space, which could lead to magnetic energy storage rings, lossless power delivery, or perhaps a large-volume magnetic shield against galactic cosmic radiation. However, perhaps the most significant enablement achieved from such a coating would be the long-term, deep space storage of cryogenic liquids, such as liquid oxygen (LOX). In our Phase I NIAC study, we realized that a combination of scattering particles and a silver backing could yield a highly effective, very broadband, reflector that could potentially reflect more than 99.9% of the Sun’s irradiant power. We developed a sophisticated model of this reflector and theoretically showed that cryogenic temperatures could be achieved in deep space at one astronomical unit (1 AU) from the Sun. We showed how this new reflector could minimize heat conduction into the cryogenic tanks by coating the tank support struts. We then modelled a strawman architecture for a mission to Mars, using a coated LOX tank, coated struts, and infrared shields, to show that with our new coating it would be possible to maintain liquid oxygen passively. As a result of this work a patent application was generated and a paper published in Optics Letters. Our Phase II NIAC study had two primary goals, to develop a rigid version of the cryogenic selective surface proposed in Phase I and to test its performance in a simulated deep space environment. During the first year of the project the work concentrated on developing rigid tiles of BaF2, leading to tiles as large as 4 inches in diameter that transmitted very little visible light. In addition, during the first year a simulated deep space environment was created using a vacuum chamber and cryocooler. Using this facility, we showed that our BaF2 tiles absorbed less than ¼% of 375 nm radiation, a significant milestone for the work. During the second year of the project, we continued to develop the BaF2 tiles and we put significant effort into the construction of a deep space environment where we could project simulated solar radiation onto a sample. In the spring of 2018, we conducted our first solar simulator test with BaF2 and saw about 3.6% absorption. This is better than the state-of-the-art, but disappointing since predictions were for much lower absorption. We, erroneously, attributed this absorption to water retention by the BaF2, and decided to change materials. We considered several oxides and settled on yttrium oxide (Y2O3) for further development, because it is broadband, lightweight, has high index, and is hydrophobic. In July 2018 we conducted our first test of a rigid tile of Y2O3 in the simulated deep space environment and saw significant absorption again. We then realized that the issue was not water, but mid-wave radiation passing through the tile and being absorbed by the temperature sensor and the varnish used to hold it in place. We wrapped the sensor in silver foil, re-ran the test, and saw much lower absorption; only 1.1%. We then re-ran the BaF2 tile and saw 1.4% absorption. These values are almost adequate to maintain LOX in deep space, but we suspect that there are still issues in our test apparatus; we suspect thermocouple wires may be absorbing radiation. Further, post-NIAC, testing will better determine the performance of our new solar reflector. In order to restrict the size of this report, we will only briefly describe topics that we have previously published, allowing us to devote more time to new material. So minimal material will be devoted to modeling the material and deep space cryogenic storage, while longer sections will cover our material development, simulated deep space testing, and new applications. The Launch Service Program (LSP) requested that we explore ways to use this new coating to maintain LOX in low Earth Orbit and that work is described. In addition, the Nuclear Thermal Propulsion (NTP) Program asked us to explore ways to reduce the heat load for liquid hydrogen, resulting in the development of a spray-on version of the coating that should significantly improve in-space multi-layer insulation performance.

Robert C. Youngquist,↗
NASA NTRS2003

Adaptive Effects on Locomotion Performance Following Exposure to a Rotating Virtual Environment

During long-duration spaceflight, astronauts experience alterations in vestibular and somatosensory cues that result in adaptive disturbances in balance and coordination upon return to Earth. These changes can pose a risk to crew safety and to mission objectives if nominal or emergency vehicle egress is required immediately following long-duration spaceflight. At present, no operational countermeasure is available to mitigate the adaptive sensorimotor component underlying the locomotor disturbances that occur after spaceflight. Therefore, the goal of this study is to develop an inflight training regimen that facilitates recovery of locomotor function after long-duration spaceflight. The countermeasure we are proposing is based on the concept of adaptive generalization. During this type of training the subject gains experience producing the appropriate adaptive motor behavior under a variety of sensory conditions and response constraints. As a result of this training a subject learns to solve a class of motor problems, rather than a specific motor solution to one problem, i.e., the subject learns response generalizability or the ability to "learn to learn." under a variety of environmental constraints. We are developing an inflight countermeasure built around treadmill exercise activities. By manipulating the sensory conditions of exercise by varying visual flow patterns, body load and speed we will systematically and repeatedly promote adaptive change in locomotor behavior. It has been shown that variable practice training increases adaptability to novel visuo-motor situations. While walking over ground in a stereoscopic virtual environment that oscillated in roll, subjects have shown compensatory torso rotation in the direction of scene rotation that resulted in positional variation away from a desired linear path. Thus, postural sway and locomotor stability in 1-g can be modulated by visual flow patterns and used during inflight treadmill training to promote adaptive generalization. The purpose of this study was to determine if adaptive modification in locomotor performance could be achieved by viewing simulated self-motion in a passive-immersive virtual ' environment over a prolonged period during treadmill locomotion.

Mulavara, A. P.↗
NASA NTRSDate not supplied

Designing for Advanced Aerial Mobility: Human-Autonomy Teaming and In-Time System-Wide Safety Assurance

The continued growth of aviation shall require new innovative technologies and operational concepts to meet the ever-increasing demands on air transportation. The NASA Advanced Air Mobility (AAM) project focuses on emerging aviation markets, such as Urban Air Mobility (UAM). UAM is defined as “...a safe and efficient system for air passenger and cargo transportation within an urban area. It is inclusive of small package delivery and other urban unmanned aerial system services and supports a mix of onboard/ground-piloted and increasingly autonomous operations” ([1]). The AAM project emphasizes technology development and validating system-level concepts and solutions in coordination with other NASA Aeronautics Research Mission Directorate (ARMD) projects to enable UAM metro- and micro-plex vertiport and airspace concepts of operations. The NASA AAM research portfolio includes the concepts of Remote Supervisor-in-Command (RSC) and Fleet and Airspace Manager (FAM) as possible human roles for consumer fleet providers. NASA research in RSC is focused on development of guidelines and standards for remote pilots/operators passively and actively controlling a large fleet of autonomous aircraft. For FAM, flight and ground system concepts and technologies to enable high density homogeneous operations at increased scale from vertiport(s), and coordination with other humans in the systems (e.g., UAM urban airspace manager, Air Traffic Control) are key research areas. The envisioned UAM operations are posited to require autonomous systems to enable functions ranging from fleet and resource management to vehicle control. Although automation has become increasingly sophisticated and ubiquitous in civil aviation, autonomy represents a significant evolution in automation, which has generally been limited in functional scope and capability. As autonomy takes on increasing responsibilities, humans and machines will be required to work together in new and different ways [2], rather than traditional design approaches focused on how machines (i.e., autonomy) can do the work of people. The emerging field of human-autonomy teaming (HAT) represents a comprehensive and prioritized research-driven approach to enable the success of future emerging aviation market applications through capabilities and principles that facilitate humans and machine working and thinking better together. The NASA Transformational Tools and Technologies (TTT) Autonomous System (AS) Sub-project was created to assist with the transition into higher levels of autonomy to enable new modes of air transportation, such as UAM. TTT-AS has identified HAT as a key research need to enable UAM while maintaining today’s ultra-safe aviation system safety levels. The latter challenge has been taken up by the NASA System-Wide Safety (SWS) Project, which recognizes that aviation safety, as it evolves, shall require new ways of thinking about safety to include integration of a wide-range of existing and new safety systems and practices, enhanced tools and technologies, increased access to data and data fusion, improved data analysis capabilities, enhanced in-time risk monitoring and detection, hazard prioritization and mitigation, safety assurance decision-support, and in-time integrated system analytics [3].The operational concept of UAM represents a variety of work that has been termed, “work-as-imagined” to characterize the idea that how people think that work is done and how work is actually done are often not the same [4]. To ensure design success and system safety, looking at “work-as-done” provides a comparative approach toward UAM concept and technology design through examination of corresponding analogs found today in aviation (e.g., on-demand operations) and other transportation domains (e.g., port operations). The paper shall discuss various alternative applications with specific focus on airline operation center (AOC) operations, and unmanned aerial system (UAS) command-and-control to inform scaled-versions of FAM and RSC, respectively, and with consideration of the national airspace system contextual environment. The tenets and principles of the HAT field and current NASA research efforts under the TTT-AS sub-project shall also be described. Finally, the SWS sub-project efforts to develop In-Time System-Wide Safety Assurance (ISSA) and In-Time Safety Management Systems (IASMS) are discussed in terms of how “in-time” safety assurance may be conceptualized for the on-demand mobility air taxi “work-as-imagined” operational concept [5]. As part of this effort, concepts from the emerging field of resilience engineering, are being studied. Traditional approaches to aviation safety have focused on what can go wrong and how to prevent it. Another approach to thinking about system safety should reflect not only “avoiding things that go wrong” (protective safety) but also “ensuring that things go right” (productive safety), that enables a system to exhibit the resilient performance [6] necessary for the success of the future aviation system emerging concepts of operations. The paper shall describe efforts focused on how productive safety and resilience may enable a more complete approach to system safety thinking and design of ISSA and IASMS for UAM. Future directions and research needs shall also be discussed.

resilience↗
NASA NTRS2016

Exhibition of Stochastic Resonance in Vestibular Perception

Astronauts experience sensorimotor changes during spaceflight, particularly during G-transitions. Post flight sensorimotor changes include spatial disorientation, along with postural and gait instability that may degrade operational capabilities of the astronauts and endanger the crew. A sensorimotor countermeasure that mitigates these effects would improve crewmember safety and decrease risk. The goal of this research is to investigate the potential use of stochastic vestibular stimulation (SVS) as a technology to improve sensorimotor function. We hypothesize that low levels of SVS will improve sensorimotor perception through the phenomenon of stochastic resonance (SR), when the response of a nonlinear system to a weak input signal is enhanced by the application of a particular nonzero level of noise. This study aims to advance the development of SVS as a potential countermeasure by 1) demonstrating the exhibition of stochastic resonance in vestibular perception, a vital component of sensorimotor function, 2) investigating the repeatability of SR exhibition, and 3) determining the relative contribution of the semicircular canals (SCC) and otolith (OTO) organs to vestibular perceptual SR. A constant current stimulator was used to deliver bilateral bipolar SVS via electrodes placed on each of the mastoid processes, as previously done. Vestibular perceptual motion recognition thresholds were measured using a 6-degree of freedom MOOG platform and a 150 trial 3-down/1-up staircase procedure. In the first test session, we measured vestibular perceptual thresholds in upright roll-tilt at 0.2 Hz (SCC+OTO) with SVS ranging from 0-700 μA. In a second test session a week later, we re-measured roll-tilt thresholds with 0, optimal (from test session 1), and 1500 μA SVS levels. A subset of these subjects, plus naive subjects, participated in two additional test sessions in which we measured thresholds in supine roll-rotation at 0.2 Hz (SCC) and upright y-translation at 1 Hz (OTO) with SVS up to 700 μA. A sinusoidal galvanic vestibular stimulation (GVS) perceptual threshold was also measured on each test day and used to normalize the SVS levels across subjects. In roll-tilt thresholds with SVS, the characteristic SR curve was qualitatively exhibited in 10 of 12 subjects, and the improvement in motion threshold was significant in 6 subjects, indicating that optimal SVS improved passive body motion perception in a way that is consistent with classical SR theory. A probabilistic comparison to numeric simulations further validated these experimental results. On the second test session, 4 out of the 10 SR exhibitors showed repeated improvement with SVS compared to the no SVS condition. Data collection is ongoing for the last two test sessions in which SCC and OTO only perceptual motion recognition thresholds are being measured with SVS. The final results of these test sessions will give insight into whether vestibular perceptual SR can occur when only one type of vestibular sensor is sensing motion or if it is more evident when sensory integration between the SCC and OTO is occurring during the motion. The overall purpose of this research is to further quantify the effects of SVS on various sensorimotor tasks and to gain a more fundamental understanding of how SVS causes SR in the vestibular system. In the context of human space flight, results from this research will help in understanding how SVS may be practically implemented in the future as a component of a comprehensive countermeasure plan for G-transition adaptation.

Galvan-Garza, R. C.↗
NASA NTRS2017

Validation and Scaling of Soil Moisture in a Semi-Arid Environment: SMAP Validation Experiment 2015 (SMAPVEX15)

The NASA SMAP (Soil Moisture Active Passive) mission conducted the SMAP Validation Experiment 2015 (SMAPVEX15) in order to support the calibration and validation activities of SMAP soil moisture data products. The main goals of the experiment were to address issues regarding the spatial disaggregation methodologies for improvement of soil moisture products and validation of the in situ measurement upscaling techniques. To support these objectives high-resolution soil moisture maps were acquired with the airborne PALS (Passive Active L-band Sensor) instrument over an area in southeast Arizona that includes the Walnut Gulch Experimental Watershed (WGEW), and intensive ground sampling was carried out to augment the permanent in situ instrumentation. The objective of the paper was to establish the correspondence and relationship between the highly heterogeneous spatial distribution of soil moisture on the ground and the coarse resolution radiometer-based soil moisture retrievals of SMAP. The high-resolution mapping conducted with PALS provided the required connection between the in situ measurements and SMAP retrievals. The in situ measurements were used to validate the PALS soil moisture acquired at 1-km resolution. Based on the information from a dense network of rain gauges in the study area, the in situ soil moisture measurements did not capture all the precipitation events accurately. That is, the PALS and SMAP soil moisture estimates responded to precipitation events detected by rain gauges, which were in some cases not detected by the in situ soil moisture sensors. It was also concluded that the spatial distribution of the soil moisture resulted from the relatively small spatial extents of the typical convective storms in this region was not completely captured with the in situ stations. After removing those cases (approximately10 of the observations) the following metrics were obtained: RMSD (root mean square difference) of0.016m3m3 and correlation of 0.83. The PALS soil moisture was also compared to SMAP and in situ soil moisture at the 36-km scale, which is the SMAP grid size for the standard product. PALS and SMAP soil moistures were found to be very similar owing to the close match of the brightness temperature measurements and the use of a common soil moisture retrieval algorithm. Spatial heterogeneity, which was identified using the high-resolution PALS soil moisture and the intensive ground sampling, also contributed to differences between the soil moisture estimates. In general, discrepancies found between the L-band soil moisture estimates and the 5-cm depth in situ measurements require methodologies to mitigate the impact on their interpretations in soil moisture validation and algorithm development. Specifically, the metrics computed for the SMAP radiometer-based soil moisture product over WGEW will include errors resulting from rainfall, particularly during the monsoon season when the spatial distribution of soil moisture is especially heterogeneous.

SMAPVEX15↗
NASA NTRS2006

Non Radiation Hardened Microprocessors in Spaced Based Remote Sensing Systems

The CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations) mission is a comprehensive suite of active and passive sensors including a 20Hz 230mj Nd:YAG lidar, a visible wavelength Earth-looking camera and an imaging infrared radiometer. CALIPSO flies in formation with the Earth Observing System Post-Meridian (EOS PM) train, provides continuous, near-simultaneous measurements and is a planned 3 year mission. CALIPSO was launched into a 98 degree sun synchronous Earth orbit in April of 2006 to study clouds and aerosols and acquires over 5 gigabytes of data every 24 hours. The ground track of one CALIPSO orbit as well as high and low intensity South Atlantic Anomaly outlines is shown. CALIPSO passes through the SAA several times each day. Spaced based remote sensing systems that include multiple instruments and/or instruments such as lidar generate large volumes of data and require robust real-time hardware and software mechanisms and high throughput processors. Due to onboard storage restrictions and telemetry downlink limitations these systems must pre-process and reduce the data before sending it to the ground. This onboard processing and realtime requirement load may mean that newer more powerful processors are needed even though acceptable radiation-hardened versions have not yet been released. CALIPSO's single board computer payload controller processor is actually a set of four (4) voting non-radiation hardened COTS Power PC 603r's built on a single width VME card by General Dynamics Advanced Information Systems (GDAIS). Significant radiation concerns for CALIPSO and other Low Earth Orbit (LEO) satellites include the South Atlantic Anomaly (SAA), the north and south poles and strong solar events. Over much of South America and extending into the South Atlantic Ocean the Van Allen radiation belts dip to just 200-800km and spacecraft entering this area are subjected to high energy protons and experience higher than normal Single Event Upset (SEU) and Single Event Latch-up (SEL) rates. Although less significant, spacecraft flying in the area around the poles experience similar upsets. Finally, powerful solar proton events in the range of 10MeV/10pfu to 100MeV/1pfu as are forecasted and tracked by NOAA's Space Environment Center in Colorado can result in Single Event Upset (SEU), Single Event Latch-up (SEL) and permanent failures such as Single Event Gate Rupture (SEGR) in some technologies. (Galactic Cosmic Rays (GCRs) are another source, especially for gate rupture) CALIPSO mitigates common radiation concerns in its data handling through the use of redundant processors, radiation-hardened Application Specific Integrated Circuits (ASIC), hardware-based Error Detection and Correction (EDAC), processor and memory scrubbing, redundant boot code and mirrored files. After presenting a system overview this paper will expand on each of these strategies. Where applicable, related on-orbit data collected since the CALIPSO initial boot on May 4, 2006 will be noted.

Decoursey, Robert J.↗
NASA NTRSDate not supplied

Accuracy of Center of Pressure Determination via Motion Capture

BACKGROUND: This study was conducted to support the stability assessment for tasks in lunar gravity and exercises on a Vibration Isolation and Stabilization (VIS) system in microgravity based on the dynamic feasibility criterion of whether the calculated position of the center of pressure (COP) falls within the base of support (BOS) which outlines the subject’s feet. Motion capture data combined with biomechanical modeling and simulation allows the forces and moments between the human and the VIS platform to be computed and the position of the COP as well as the location and shape of the BOS to be determined. The goal of this study was to assess the accuracy of the COP trajectory calculated using motion capture-based data. METHODS AND RESULTS: To obtain the dynamic quantities from which COP is calculated, motion capture data is first collected in the 1g lab environment by recording the trajectories of passive retroreflective markers placed on a subject during exercise or performance of a given task. The OpenSim [1] inverse kinematics (IK) tool is used to fit a scaled subject model to recorded marker trajectories while minimizing marker error to obtain joint angles. Then, a custom OpenSim plugin [2] is used to determine the subject’s time-varying moment of inertia and its time derivative, center of mass (CM) position, velocity, and acceleration, as well as the angular momentum and its time derivative relative to the subject’s CM. Some of these quantities are not needed for modeling tasks performed on a stationary lunar surface but, due to the moving exercise platform, are needed to model VIS response to the subject’s motion. Hand positions, used in calculating a cable force if present, are recorded as well. These quantities are used to calculate the total force (F ⃗^((plate) )) and moment (M ⃗^((plate) )) exerted by the lunar surface or the VIS plate on the subject’s shoe soles. COP is then calculated from the following equations: r_x^((cop) )= M_z^((plate) )/F_y^((plate) ) and r_z^((cop) )= 〖-M〗_x^((plate) )/F_y^((plate) ), where the y axis is normal to the surface. COP accuracy for feasibility assessments is then determined by whether it falls within the BOS, which is also computed by the plugin. To study the accuracy of COP calculated from motion capture, we first investigated whether COP remained within the BOS, as it must, for exercises performed in the 1g lab environment. Standard exercises such as back squat and deadlift were analyzed, as well as more explosive exercises including hang clean and press. Cases in which the COP exited the BOS indicated that COP accuracy required further investigation. In this study, an exercise device with cables was used, so cable force modeling accuracy should also be considered. In a separate study, we collected motion capture and force plate data for twenty-seven motions not involving an exercise device. About a third were genuine countermeasures exercises (e.g., hang clean and press), some were relevant for lunar tasks (e.g., object pick up), and the rest were of a “unit test” nature (e.g., swaying back and forth or side to side). Motion capture-based COP positions were compared with force plate measured COP. We found that while force plate measured COP remained within the BOS, motion capture-based COP was observed to briefly exit the BOS on occasion. Techniques to mitigate IK artifacts and filtering of calculated data could be used to improve the agreement of calculated and measured results, resolving excursions from the BOS within this dataset. The mean error between calculated and measured COP was found to be less than 6 mm. Additionally, we derived and investigated equations for the COP in terms of the cable force, cable location, as well as the human CM position, acceleration, and angular momentum with respect to the CM, and analyzed them for sensitivity to errors in individual quantities. Several were found, but the most significant one was that when the vertical force on the feet approaches zero, indicating a near-detachment or ‘jump off’ condition, errors are amplified. This is consistent with the observation that in the absence of pressure, the concept of the center of pressure would become meaningless.

C A Bell↗
NASA NTRS2006

The Use of Dynamic Visual Acuity as a Functional Test of Gaze Stabilization Following Space Flight

After prolonged exposure to a given gravitational environment the transition to another is accompanied by adaptations in the sensorimotor subsystems, including the vestibular system. Variation in the adaptation time course of these subsystems, and the functional redundancies that exist between them make it difficult to accurately assess the functional capacity and physical limitations of astro/cosmonauts using tests on individual subsystems. While isolated tests of subsystem performance may be the only means to address where interventions are required, direct measures of performance may be more suitable for assessing the operational consequences of incomplete adaptation to changes in the gravitational environment. A test of dynamic visual acuity (DVA) is currently being used in the JSC Neurosciences Laboratory as part of a series of measures to assess the efficacy of a countermeasure to mitigate postflight locomotor dysfunction. In the current protocol, subjects visual acuity is determined using Landolt ring optotypes presented sequentially on a computer display. Visual acuity assessments are made both while standing and while walking at 1.8 m/s on a motorized treadmill. The use of a psychophysical threshold detection algorithm reduces the required number of optotype presentations and the results can be presented immediately after the test. The difference between the walking and standing acuity measures provides a metric of the change in the subject s ability to maintain gaze fixation on the visual target while walking. This functional consequence is observable regardless of the underlying subsystem most responsible for the change. Data from 15 cosmo/astronauts have been collected following long-duration (approx. 6 months) stays in space using a visual target viewing distance of 4.0 meters. An investigation of the group mean shows a change in DVA soon after the flight that asymptotes back to baseline approximately one week following their return to earth. The performance of some subjects nicely parallels the stereotypical recovery curve observed in the group mean data. Others show dramatic changes in DVA from one test day to another. These changes may be indicative of a re-adaptation process that is not characterized by a steady improvement with the passage of time, but is instead a dynamic search for appropriate coordinative strategy to achieve the desired gaze stabilization goal. Ground-based data have been collected in our lab using DVA with one of the goals being to improve the DVA test itself. In one of these studies, the DVA test was repeated using a visual target viewing distance of 0.5 meters. While walking, the relative contributions of the otoliths and semi-circular canals that are required to stabilize gaze are affected by visual target viewing distance. It may be possible to exploit this using the current treadmill DVA test to differentially assess changes in these vestibular subsystems. The postflight DVA evaluations currently used have been augmented to include the near target version of the test. Preliminary results from these assessments, as well as the results from the ground-based tests will also be reported. DVA provides a direct measure of a subject's ability to see clearly in the presence of self-motion. The use of the current tests for providing a functionally relevant metric is evident. However, it is possible to expand the scope of DVA testing to include scenarios other than walking. A facility for measuring DVA in the presence of passive movements is being created. Using a mechanized platform to provide the perturbation, it should be possible to simulate aircraft and automobile vibration profiles. Used in conjunction with the far and near visual displays this facility should be able to assess a subject s ability to clearly see distant objects as well as those that appear on the dashboard or instrument control panel during functionally relevant situations.

Peters, B. T.↗
NASA NTRS2022

Deriving Severe Hail Likelihood from Satellite Observations and Model Reanalysis Parameters using a Deep Neural Network

Geostationary satellite imagers, such as those of the Geostationary Operational Environmental Satellite (GOES) series, have been observing severe convection at 15–60-minute intervals for over 40 years. When properly assessed, such a data record can be valuable in efforts of estimating severe storm risk throughout the diurnal cycle based on automated detection of patterns consistently found atop severe storms. Furthermore, environmental conditions favorable for severe weather are well-known and are thought to be represented well by modern reanalysis products. Promoting resilience against such hazards on local and global scales is a chief goal the NASA Disasters program, which seeks to encourage use of satellite observations to mitigate risk. For instance, hail is the costliest severe weather hazard across the globe in terms of insured loss, but reporting inconsistencies for hail events globally make it difficult to develop models that can quantify the risk. Satellite observation and model reanalysis taken together have the potential to, with reasonable skill and specificity, characterize environmental conditions that are favorable for hazardous weather, and thereby enable creation of hazard climatologie. Such climatologies are particularly useful over regions without extensive radar networks or storm reporting. By mapping the multivariate combination of observed cloud features and reanalysis environmental parameters/indices to United States Next Generation Weather Radar (NEXRAD) radar-estimated Maximum Expected Size of Hail (MESH) by way of a deep neural network (DNN), estimates of likelihood for potentially severe hail can be produced. Such estimates are of greater complexity and efficiency than could be performed with previous multivariate or logistic regression analyses for observed points within convective systems. Statistical distributions of convective parameters from satellite and reanalysis are shown to highlight non-severe/severe class separation for well-known hailstorm predictors, e.g., overshooting cloud top characteristics, deep-layer wind shear, mid-level stability, helicity, and convective inhibition. These complex, multivariate predictor relationships are exploited within a DNN, which can efficiently produce a quantitative hail risk metric with better than 70% detection rate and under 30% false alarms. These hail classifications can then be aggregated across the satellite record to yield a hazard climatology for hail frequency and severity – knowledge of which is of particular interest to those who manage risk (e.g., insurers) and are seeking opportunities to identify hail-prone regions, particularly in developing nations. This NASA study uses satellite observations and model parameters in a DNN to perform climatological hailstorm analysis in support of catastrophe model development, with the hope of promoting risk resilience particularly in regions without adequate weather radar coverage.

Passive Remote Sensing↗
NASA NTRSDate not supplied

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗
NASA NTRSDate not supplied

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗
NASA NTRSDate not supplied

An Overview of Experiments and Modeling of Polysiloxane-Coated Thermal Protection Systems for Missions to Mars, Titan, and Beyond.

Phenolic Impregnated Carbon Ablator (PICA) gained heritage during the historic Stardust mission, where it successfully returned samples from a comet’s tail and has since been instrumental in delivering payloads to the surface of Mars [1-3]. Most recently, PICA enabled the safe return of samples collected from asteroid Bennu as part of the OSIRIS-REx mission. This rich legacy underscores PICA’s critical role in allowing NASA’s most ambitious exploration missions. However, the friable nature of its phenolic phase presents challenges during handling and pre-launch activities. To mitigate this issue, PICA is coated with a polysiloxane resin system, which serves to suppress particulate dispersion and thereby safeguard spacecraft components. A comprehensive understanding of the polysiloxane resin’s behavior is imperative, as it profoundly shapes the material response of PICA during atmospheric entry by influencing its thermal and oxidative stability. This influence extends to thermocouple plugs embedded within thermal protection systems. These plugs have demonstrated their significance in missions such as Mars Science Laboratory (MSL) and Mars 2020, where the MEDLI and MEDLI2 instrumentation suites delivered in-valuable insights into the performance of thermal protection systems during entry into the Martian atmosphere [4]. Looking ahead, missions such as Dragonfly, set to descend into Titan’s dense atmosphere, aim to leverage advanced sensor technologies to further refine our understanding of thermal protection response [5]. Moreover, thermocouple plugs play an essential role in validating cutting-edge material response models, such as those pioneered under NASA’s Entry Systems Modeling Project (ESM), designed, in-part, to predict the operational integrity of thermal protection systems under the extreme stresses of atmospheric entry. To achieve these modeling goals, ground-based experiments are crucial to provide the foundational data necessary for developing and refining these predictive tools. To this end, an extensive test campaign was conducted at the Hypersonic Materials Environmental Test System (HyMETS) to investigate the high-temperature behavior of the polysiloxane resin in an air environment [6]. These experiments revealed critical phenomena, including the formation of a silicon oxycarbide layer that enhances oxidation resistance, moderates surface temperatures, and alters in-depth thermal response. Building on these findings, subsequent tests were designed to simulate atmospheric entry conditions in reactive gases, such as CO2 and N2, to mimic the environments of Mars and Titan, respectively, as well as non-reactive gases representing the atmospheres of the Ice Giants (Neptune and Uranus). A heating rate dependent decomposition mechanism has been identified for the polysiloxane resin under oxidizing conditions (Fig. 1). In the initial stage, the resin and the underlying thermal protection system undergo pyrolysis, rapidly generating a thin amorphous silicon oxycarbide interwoven with carbonaceous char and residual fibers from PICA. During the second stage, the nascent oxide layer establishes a robust, oxidation-resistant thermal barrier coating, which significantly impedes heat transfer to the underlying carbonaceous char, resulting in a stagnation of the surface temperature. A key factor contributing to this thermal resistance is the low recombination efficiency of atomic oxygen (γ), which further diminishes the heat load on the material’s interior layers [7]. Moreover, as the surface temperature stagnates, the silicon oxycarbide phase separates into distinct regions of silica and free graphite. Ultimately, when the heat flux reaches a critical threshold, a third stage is triggered, leading to the breakdown of the coating through carbothermal reduction, exposing the underlying char layer. This exposure leads to a dramatic surface temperature spike, driven by highly exothermic reactions between atomic oxygen and the char layer, further accelerating material degradation. A detailed mass and heat transfer model of PICA coated with polysiloxane resin was implemented in the Porous material Analysis Toolbox based on OpenFOAM, PATO [8]. The initial stage was considered negligible in this model because the resin decomposition occurs rapidly within a thin surface layer. Instead, the coating was directly considered as an oxygen-resistant thermal barrier coating. For the second stage, the thin amorphous silicon oxycarbide was treated as a pure silica surface to simplify the thermochemical behavior. The model ac-counts for surface equilibrium processes using representative elements of the coating-environment system. For the third stage, specific boundary conditions were developed to estimate the onset and progression of the coating removal. Two-dimensional material response simulations were conducted to compare uncoated and coated PICA using boundary conditions calibrated with HyMETS data. Fig. 2 illustrates that the simulations closely align with experimental data, successfully reproducing measured temperature profiles. This work will include the latest advancements in the coating model, including the calibration of recombination of atomic oxygen at the surface during the second phase. These simulated results will be further validated against additional CO2 data points from HyMETS, reinforcing the models’ predictive capabilities. These mechanisms and their effects on thermal protection systems, including thermochemical behavior and thermocouple probe performance in extreme environments, provide crucial insights for optimizing spacecraft designs that safeguard scientific payload and ensure mission success in future planetary exploration endeavors.

Active Oxidation↗