Search NASA⌕ Search

SEARCH · Search NASA

Results for “Principal Component”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Performance of Optimized Actuator and Sensor Arrays in an Active Noise Control System

Experiments have been conducted in NASA Langley's Acoustics and Dynamics Laboratory to determine the effectiveness of optimized actuator/sensor architectures and controller algorithms for active control of harmonic interior noise. Tests were conducted in a large scale fuselage model - a composite cylinder which simulates a commuter class aircraft fuselage with three sections of trim panel and a floor. Using an optimization technique based on the component transfer functions, combinations of 4 out of 8 piezoceramic actuators and 8 out of 462 microphone locations were evaluated against predicted performance. A combinatorial optimization technique called tabu search was employed to select the optimum transducer arrays. Three test frequencies represent the cases of a strong acoustic and strong structural response, a weak acoustic and strong structural response and a strong acoustic and weak structural response. Noise reduction was obtained using a Time Averaged/Gradient Descent (TAGD) controller. Results indicate that the optimization technique successfully predicted best and worst case performance. An enhancement of the TAGD control algorithm was also evaluated. The principal components of the actuator/sensor transfer functions were used in the PC-TAGD controller. The principal components are shown to be independent of each other while providing control as effective as the standard TAGD.

Palumbo, D. L.↗
NASA NTRS1996

Performance of Optimized Actuator and Sensor Arrays in an Active Noise Control System

Experiments have been conducted in NASA Langley s Acoustics and Dynamics Laboratory to determine the effectiveness of optimized actuator/sensor architectures and controller algorithms for active control of harmonic interior noise. Tests were conducted in a large scale fuselage model - a composite cylinder which simulates a commuter class aircraft fuselage with three sections of trim panel and a floor. Using an optimization technique based on the component transfer functions, combinations of 4 out of 8 piezoceramic actuators and 8 out of 462 microphone locations were evaluated against predicted performance. A combinatorial optimization technique call tabu search was employed to select the optimum transducer arrays. Three test frequencies represent the cases of a strong acoustic and strong structural response, a weak acoustic and strong structural response and a strong acoustic and weak structural response. Noise reduction was obtained using a Time Averaged/Gradient Descent (TAGD) controller. Results indicate that the optimization technique successfully predicted best and worst case performance. An enhancement of the TAGD control algorithm was also evaluated. The principal components of the actuator/sensor transfer functions were used in the PC-TAGD controller. The principal components are shown to be independent of each other while providing control as effective as the standard TAGD.

Palumbo, D. L.↗
NASA NTRS1976

Ocean color spectra measured off the Oregon coast - Characteristic vectors

The ocean color spectrum is defined as the ratio of the spectrum of light upwelled from the sea to the spectrum of light incident on the sea surface. Ocean color spectra, observed from an airplane flown over waters off Oregon, are analyzed. The original spectra are resolved into fifty-five wavelength bands, each 5 nm wide. The shapes of these spectra are parameterized by, and shown to be accurately recoverable from, their first four principal components. These components are the scalar projections of each spectrum on the first four characteristic vectors of the sample covariance matrix. Regression equations are found with which phytoplankton pigment concentration and water transparency may be estimated as linear functions of the principal components. Pigment concentration estimates thus obtained are imprecise. The poor fit is at least partly due to the inappropriateness of the linear regression model and the neglect of other optically important substances typically present in sea water.

Mueller, J. L.↗
NASA NTRS1974

Chain pooling to minimize prediction errors in subset regression

The existing theory of subset regression is examined, taking into account optimality criteria, small experiments, nonlinear models, colinearities, and special techniques. Approaches based on chain pooling coupled with principal components regression are discussed, giving attention to a comparison of half-normal plotting with chain pooling, a procedure based on prior ordering, deletion under the F-test, the largest of a set of chi-square variates, and principal components regression and model deletion. The choice of a true (population) model for simulations is considered along with the evaluation of the decision procedure and suitable computer programs.

Holms, A. G.↗
DOE OSTI2024

Cover crops and poultry litter impact on soil structural stability in dryland soybean production in southeastern United States

Abstract This study explored the efficacy of soil aggregate indices in quantifying soil structural development, utilizing 5‐year field experiment data from the Southeastern United States. The experiment utilized a split‐plot design with cover crops (native vegetation as control, cereal rye (Secale cerealeL.), winter wheat (Triticum aestivum), hairy vetch (Vicia villosa), and mustard (Brassica rapa) plus cereal rye as the main factor and fertilizer source (no fertilizer as control, inorganic fertilizer with phosphorus, potassium, and elemental sulfur, and poultry litter) as the secondary factor. Aggregate size fractions were determined using the wet‐sieving method, and aggregate stability index (ASI), mean weight diameter (MWD), geometric mean diameter (GMD), and fractal dimension (FD) were calculated to assess soil structural stability. Main effects results indicated that cereal rye (55.11%) and poultry litter (50.97%) exhibited the highest ASI values. The highest MWD, GMD, and FD were observed under mustard plus cereal rye (1.187 mm), cereal rye (0.462 mm), and hairy vetch (2.573), respectively. Principal component analysis revealed that cover crops significantly improved soil aggregate structure and stability, overcoming limitations of sole fertilization practices. Regression analysis suggested that ASI, MWD, and GWD positively correlated with soil organic carbon, whereas FD negatively correlated with MWD, GMD, and ASI. Principal component analysis exhibited that FD decreased with increasing soil organic carbon, ASI, MWD, and GMD, demonstrating that lower FD values indicate enhanced soil aggregation and structure. Assessed indices, FD included, effectively gauged soil structural stability. These metrics should be prioritized in managerial decisions to support soil productivity and health in agricultural systems.

Agriculture↗
NASA NTRS1982

Structure and physics of solar faculae. II - The non-thermal velocity field above faculae

The OSO-8 satellite enabled the study of various characteristics of the profiles of Si II, Si IV, C IV, and O VI lines above active areas of the sun, as well as above quiet areas, and the derivation of some physical properties of the transition region between chromosphere and corona (CCT). The study of the lines shows a general tendency for the microvelocity fields on the average to be nearly constant for the heights corresponding to a temperature greater than 100,000 K; however they seem to slightly increase with height in quiet areas, and decrease in active areas. A multicomponent model of the CCT is necessary, and its geometry is far from being a set of plane-parallel columns. It is similar to an association of moving knots within the nonmoving principal component of the matter. The proportion of mass, in the knots relative to that in the nonmoving component, is several times larger in active regions than in quiet regions. In the knots, the nonthermal microvelocity fields are smaller in active regions and seem to decrease for temperature increasing above 100,000 K, contrary to what happens in the steady principal component.

Mouradian, Z.↗
NASA NTRS2013

Quantitative Comparison of the Variability in Observed and Simulated Shortwave Reflectance

The Climate Absolute Radiance and Refractivity Observatory (CLARREO) is a climate observation system that has been designed to monitor the Earth's climate with unprecedented absolute radiometric accuracy and SI traceability. Climate Observation System Simulation Experiments (OSSEs) have been generated to simulate CLARREO hyperspectral shortwave imager measurements to help define the measurement characteristics needed for CLARREO to achieve its objectives. To evaluate how well the OSSE-simulated reflectance spectra reproduce the Earth s climate variability at the beginning of the 21st century, we compared the variability of the OSSE reflectance spectra to that of the reflectance spectra measured by the Scanning Imaging Absorption Spectrometer for Atmospheric Cartography (SCIAMACHY). Principal component analysis (PCA) is a multivariate decomposition technique used to represent and study the variability of hyperspectral radiation measurements. Using PCA, between 99.7%and 99.9%of the total variance the OSSE and SCIAMACHY data sets can be explained by subspaces defined by six principal components (PCs). To quantify how much information is shared between the simulated and observed data sets, we spectrally decomposed the intersection of the two data set subspaces. The results from four cases in 2004 showed that the two data sets share eight (January and October) and seven (April and July) dimensions, which correspond to about 99.9% of the total SCIAMACHY variance for each month. The spectral nature of these shared spaces, understood by examining the transformed eigenvectors calculated from the subspace intersections, exhibit similar physical characteristics to the original PCs calculated from each data set, such as water vapor absorption, vegetation reflectance, and cloud reflectance.

Roberts, Yolanda, L.↗
NASA NTRSDate not supplied

Validation of CrIS Ozone and Carbon Oxide Products from CrIS Single-Field-of-View Retrievals

Single Field-of-view Sounder Atmospheric Products (SiFSAP) from Cross-track Infrared Sounder (CrIS) on S-NPP have been developed at NASA Langley Research center, and recently a significant improvement in its trace gases products has been made. These products are derived based on the Principal Component (PC)-based Radiative Transfer Model (PCRTM) and an optimal estimation retrieval method (PCRTM-RA). Use of the PCRTM in this method allows for fast and accurate calculations for thousands of spectral channels under clear and cloudy sky conditions. The use of principal component to compress information from all spectral channels into the PC domain enables to reduce the observational noise and use the information from all hyperspectral infrared channels. The retrieval is made on PC-domain, and temperature, water vapor, trace gases, cloud and surface parameters are retrieved simultaneously. This presentation will present some validation to the SiFSAP ozone (O3) and carbon monoxide (CO) products. Since the SiFSAP has a spatial resolution of about 14 km at nadir, which is better than most global weather and climate models and enables to make process-oriented analysis of the transport of these gases, this study will focus on validation of CO and O3 products under some extreme weather and/or climate events, such as CO emission and transport from large biomass burning, and O3 variation impacted by fire emission, stratospheric intrusion, and tropical cyclones. Data used in our validation include CO and O3 from NASA aircraft campaigns, plus other satellite products such as CO and O3 from AIRS, IASI and TROPOMI, MOPPIT CO and OMPS O3. Some comparison of SiFSAP O3 with the O3 from the fifth-generation ECMWF reanalysis (ERA5) data the NASA Modern-Era Retrospective Analysis for Research and Applications, Version 2 (MERRA-2) will also present. Such a validation not only helps to quantify the performance of the retrievals in these extreme conditions, but also displays the capability of satellite observation to capture the fine-scale spatial pattern of CO and O3 variation.

Xiaozhen Xiong↗
NASA NTRS1991

Humidity profiles over the ocean

The variabilities of atmospheric humidity profile over oceans from daily to interannual time scales were examined using 9 years of daily and semidaily radiosonde soundings at island stations extending from the Arctic to the South Pacific. The relative humidity profiles were found to have considerable temporal and geographic variabilities, contrary to the prevalent assumption. Principal component analysis on the profiles of specific humidity were used to examine the applicability of a relation between the surface-level humidity and the integrated water vapor; this relation has been used to estimate large-scale evaporation from satellite data. The first principal component was found to correlate almost perfectly with the integrated water vapor. The fractional variance represented by this mode increases with increasing period. It reaches approximately 90 percent at two weeks and decreases sharply, below one week, down to approximately 60 percent at the daily period. At low frequencies, the integrated water vapor appeared to be an adequate estimator of the humidity profile and the surface-level humidity. At periods shorter than a week, more than one independent estimator is needed.

Liu, W. T.↗
NASA NTRS2011

Jovian Chromophore Characteristics from Multispectral HST Images

The chromophores responsible for coloring the jovian atmosphere are embedded within Jupiter's vertical aerosol structure. Sunlight propagates through this vertical distribution of aerosol particles, whose colors are defined by omega-bar (sub 0)(lambda), and we remotely observe the culmination of the radiative transfer as I/F(lambda). In this study, we employed a radiative transfer code to retrieve omega-bar (sub 0)(lambda) for particles in Jupiter's tropospheric haze at seven wavelengths in the near-UV and visible regimes. The data consisted of images of the 2008 passage of Oval BA to the south of the Great Red Spot obtained by the Wide Field Planetary Camera 2 on-board the Hubble Space Telescope. We present derived particle colors for locations that were selected from 14 weather regions, which spanned a large range of observed colors. All omega-bar (sub 0)(lambda) curves were absorbing in the blue, and omega-bar (sub 0)(lambda) increased monotonically to approximately unity as wavelength increased. We found accurate fits to all omega-bar (sub 0)(lambda) curves using an empirically derived functional form: omega-bar (sub 0)(lambda) = 1 A exp(-B lambda). The best-fit parameters for the mean omega-bar (sub 0)(lambda) curve were A = 25.4 and B = 0.0149 for lambda in units of nm. We performed a principal component analysis (PCA) on our omega-bar (sub 0)(lambda) results and found that one or two independent chromophores were sufficient to produce the variations in omega-bar (sub 0)(lambda). A PCA of I/F(lambda) for the same jovian locations resulted in principal components (PCs) with roughly the same variances as the omega-bar (sub 0)(lambda) PCA, but they did not result in a one-to-one mapping of PC amplitudes between the omega-bar (sub 0)(lambda) PCA and I/F(lambda) PCA. We suggest that statistical analyses performed on I/ F(lambda) image cubes have limited applicability to the characterization of chromophores in the jovian atmosphere due to the sensitivity of 1/ F(lambda) to horizontal variations in the vertical aerosol distribution.

Strycker, Paul D.↗
NASA NTRS1982

Classification of surface units in the equatorial region of Mars based on Viking Orbiter color, albedo, and thermal data

Clusters corresponding to mappable surface units are sought in Viking Orbiter color, albedo, and thermal inertia data for the equatorial region of Mars. A principal components analysis indicated that 84% of the variance within the data for this region can be carried along two vector directions which typify the dominant trend of Martian surface materials. These dominant trends were deemphasized by stretching the data from a five-dimensional elliptical swarm into a hypersphere, through the use of principal component techniques. The decorrelated data were then plotted in a triangle diagram with red/violet, albedo and thermal inertia apices to facilitate inherent cluster discrimination. As many as eight clusters can be identified, with important mixing between them. The three major clusters consist of red and grey material extremes, along with intermediate value materials.

Arvidson, R. E.↗
NASA NTRS1984

Characterization of surficial geologic units on Venus from Pioneer Venus radar data: A progress report

A classification database using the reflectivity (derived from the altimetry data), rms slope, and the first principal component of altimetry and topographic slope is presented. The resultant clustered data is examined qualitatively as well as quantitatively, to establish the statistical integrity of each cluster by use of an interactive, ternary plotting algorithm. This algorithm plots, for a cluster, the position of each of its pixels within a ternary diagram whose apices represent reflectivity, rms slope, and the first principal component. The digital values in these three databases are normalized such that unity is represented by a value of 255 in each database. The frequencies of each plotted point within the ternary diagram are recorded in order to establish the mode of each cluster. The pixels of each cluster are displayed as one separate color; their ternary plot will show not only the interrelations between clusters, but also the presence of any anomalous points within a cluster. Existing lunar and terrestrial analog radar data is used to establish fields within this ternary diagram that are indicative of as many different geologic materials and tectonics settings as possible. The resultant fields are used to determine empirically the geologic significance of the clusters resulting from the cluster analysis.

Davis, P. A.↗
NASA NTRS1985

Comparative techniques used to evaluate Thematic Mapper data for land cover classification in Logan County, West Virginia

Several digital data processing techniques were evaluated in an effort to identify and map active/abandoned, partially reclaimed, and fully revegetated surface mine areas in the central portion of Logan County. The TM data were first subjected to various enhancement procedures, including a linear contrast stretch, principal components and canonical analysis transformations. At the same time, four general procedures were followed to produce six classifications as a means of comparing the techniques involved. Preliminary results show that various feature extraction/data reduction techniques provide classification results equal or superior to the more straightforward unsupervised clustering technique. Analyst interaction time for labelling clusters is reduced using the canonical analysis and principal components procedures, though the canonical technique has clearly produced better results to date.

Brumfield, J. O.↗
DOE OSTI2022

Star–Galaxy Image Separation with Computationally Efficient Gaussian Process Classification

Abstract We introduce a novel method for discerning optical telescope images of stars from those of galaxies using Gaussian processes (GPs). Although applications of GPs often struggle in high-dimensional data modalities such as optical image classification, we show that a low-dimensional embedding of images into a metric space defined by the principal components of the data suffices to produce high-quality predictions from real large-scale survey data. We develop a novel method of GP classification hyperparameter training that scales approximately linearly in the number of image observations, which allows for application of GP models to large-size Hyper Suprime-Cam Subaru Strategic Program data. In our experiments, we evaluate the performance of a principal component analysis embedded GP predictive model against other machine-learning algorithms, including a convolutional neural network and an image photometric morphology discriminator. Our analysis shows that our methods compare favorably with current methods in optical image classification while producing posterior distributions from the GP regression that can be used to quantify object classification uncertainty. We further describe how classification uncertainty can be used to efficiently parse large-scale survey imaging data to produce high-confidence object catalogs.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1983

Shuttle Imaging Radar-A (SIR-A) data as a complement to Landsat Multispectral Scanner (MSS) data

Principal components analysis and supervised classifications were performed on two dates of Landsat multispectral scanner (MSS) data registered to one date of Shuttle Imaging Radar-A (SIR-A) data in a wheat-growing area of New South Wales, Australia. The purpose was to evaluate SIR-A data as a complement to Landsat MSS data in an agricultural environment. The SIR-A data was filtered using a 7 x 7 pixel moving window median filter. Principal components analysis indicated the SIR-A data were discriminating between trees and agricultural fields. Supervised classifications using wheat, pasture, trees, and idle classes resulted in increased accuracies for wheat and pasture and slightly decreased accuracies for trees and idle for the Landsat MSS/SIR-A registered data sets over the Landsat MSS alone. Overall classification accuracies were unchanged for one date and substantially increased for the other when the SIR-A data were added to the Landsat MSS data.

Henninger, D. L.↗
NASA NTRS2002

Continuum Fitting HST QSO Spectra

The Principal Component Analysis (PCA) method which we are using to fit and describe QSO spectra relies upon the fact that QSO continuum are generally very smooth and simple except for emission and absorption lines. To see this we need high signal-to-noise (S/N) spectra of QSOs at low redshift which have relatively few absorption lines in the Lyman-a forest. We need a large number of such spectra to use as the basis set for the PCA analysis which will find the set of principal component spectra which describe the QSO family as a whole. We have found that too few HST spectra have the required S/N and hence we need to supplement them with ground based spectra of QSOs at higher redshift. We have many such spectra and we have been working to make them suitable for this analysis. We have concentrated on this topic since 12/15/01.

Tytler, David↗
DOE OSTI2023

What drives the variance of galaxy spectra?

We present a study aimed at understanding the physical phenomena underlying the formation and evolution of galaxies following a data-driven analysis of spectroscopic data based on the variance in a carefully selected sample. We apply principal component analysis (PCA) independently to three subsets of continuum-subtracted optical spectra, segregated into their nebular emission activity as quiescent, star-forming, and active galactic nuclei (AGNs). We emphasize that the variance of the input data in this work only relates to the absorption lines in the photospheres of the stellar populations. The sample is taken from the Sloan Digital Sky Survey (SDSS) in the stellar velocity dispersion range 100–150 km s −1 , to minimize the ‘blurring’ effect of the stellar motion. We restrict the analysis to the first three principal components (PCs) and find that PCA segregates the three types with the highest variance mapping SSP-equivalent age, along with an inextricable degeneracy with metallicity, even when all three PCs are included. Spectral fitting shows that stellar age dominates PC1, whereas PC2 and PC3 have a mixed dependence of age and metallicity. The trends support – independently of any model fitting – the hypothesis of an evolutionary sequence from star formation to AGN to quiescence. As a further test of the consistency of the analysis, we apply the same methodology in different spectral windows, finding similar trends, but the variance is maximal in the blue wavelength range, roughly around the 4000 Å break.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2001

Relative effectiveness of kinetic analysis vs single point readings for classifying environmental samples based on community-level physiological profiles (CLPP)

The relative effectiveness of average-well-color-development-normalized single-point absorbance readings (AWCD) vs the kinetic parameters mu(m), lambda, A, and integral (AREA) of the modified Gompertz equation fit to the color development curve resulting from reduction of a redox sensitive dye from microbial respiration of 95 separate sole carbon sources in microplate wells was compared for a dilution series of rhizosphere samples from hydroponically grown wheat and potato ranging in inoculum densities of 1 x 10(4)-4 x 10(6) cells ml-1. Patterns generated with each parameter were analyzed using principal component analysis (PCA) and discriminant function analysis (DFA) to test relative resolving power. Samples of equivalent cell density (undiluted samples) were correctly classified by rhizosphere type for all parameters based on DFA analysis of the first five PC scores. Analysis of undiluted and 1:4 diluted samples resulted in misclassification of at least two of the wheat samples for all parameters except the AWCD normalized (0.50 abs. units) data, and analysis of undiluted, 1:4, and 1:16 diluted samples resulted in misclassification for all parameter types. Ordination of samples along the first principal component (PC) was correlated to inoculum density in analyses performed on all of the kinetic parameters, but no such influence was seen for AWCD-derived results. The carbon sources responsible for classification differed among the variable types with the exception of AREA and A, which were strongly correlated. These results indicate that the use of kinetic parameters for pattern analysis in CLPP may provide some additional information, but only if the influence of inoculum density is carefully considered. c2001 Elsevier Science Ltd. All rights reserved.

NASA Center KSC↗