Search NASA⌕ Search

SEARCH · Search NASA

Results for “RADAR EQUIPMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Evaluation of Flight Deck-Based Interval Management Crew Procedure Feasibility

Air traffic demand is predicted to increase over the next 20 years, creating a need for new technologies and procedures to support this growth in a safe and efficient manner. The National Aeronautics and Space Administration's (NASA) Air Traffic Management Technology Demonstration - 1 (ATD-1) will operationally demonstrate the feasibility of efficient arrival operations combining ground-based and airborne NASA technologies. The integration of these technologies will increase throughput, reduce delay, conserve fuel, and minimize environmental impacts. The ground-based tools include Traffic Management Advisor with Terminal Metering for precise time-based scheduling and Controller Managed Spacing decision support tools for better managing aircraft delay with speed control. The core airborne technology in ATD-1 is Flight deck-based Interval Management (FIM). FIM tools provide pilots with speed commands calculated using information from Automatic Dependent Surveillance - Broadcast. The precise merging and spacing enabled by FIM avionics and flight crew procedures will reduce excess spacing buffers and result in higher terminal throughput. This paper describes a human-in-the-loop experiment designed to assess the acceptability and feasibility of the ATD-1 procedures used in a voice communications environment. This experiment utilized the ATD-1 integrated system of ground-based and airborne technologies. Pilot participants flew a high-fidelity fixed base simulator equipped with an airborne spacing algorithm and a FIM crew interface. Experiment scenarios involved multiple air traffic flows into the Dallas-Fort Worth Terminal Radar Control airspace. Results indicate that the proposed procedures were feasible for use by flight crews in a voice communications environment. The delivery accuracy at the achieve-by point was within +/- five seconds and the delivery precision was less than five seconds. Furthermore, FIM speed commands occurred at a rate of less than one per minute, and pilots found the frequency of the speed commands to be acceptable at all times throughout the experiment scenarios.

Wilson, Sara R.↗
NASA NTRS1966

Radio electronics

Low noise amplifiers, laser radar optics, gas lasers and holography, and microminiaturized solid state devices for radio electronics

LIDAR↗
NASA NTRS2011

LIDAR Metrology for Prescription Characterization and Alignment of Large Mirrors

We describe the use of LIDAR, or "laser radar," (LR) as a fast, accurate, and non-contact tool for the measurement of the radius of curvature (RoC) of large mirrors. We report the results of a demonstration of this concept using a commercial laser radar system. We measured the RoC of a 1.4m x 1m spherical mirror with a nominal RoC of 4.6 m with a manufacturing tolerance of 4600mm +/- 6mm. The prescription of the mirror is related to its role as ground support equipment used in the test of part of the James Webb Space Telescope (JWST). The RoC of such a large mirror is not easily measured without contacting the surface. From a position near the center of curvature of the mirror, the LIDAR scanned the mirror surface, sampling it with 1 point per 3.5 sq cm. The measurement consisted of 3983 points and lasted only a few minutes. The laser radar uses the LIDAR signal to provide range, and encoder information from angular azimuth and elevation rotation stages provide the spherical coordinates of a given point. A best-fit to a sphere of the measured points was performed. The resulting RoC was within 20 ppm of the nominal RoC, also showing good agreement with the results of a laser tracker-based, contact metrology. This paper also discusses parameters such as test alignment, scan density, and optical surface type, as well as future possible application for full prescription characterization of aspherical mirrors, including radius, conic, off-axis distance, and aperture.

Eegholm, B.↗
NASA NTRS1976

Accident investigation: Analysis of aircraft motions from ATC radar recordings

A technique was developed for deriving time histories of an aircraft's motion from air traffic control (ATC) radar records. This technique uses the radar range and azimuth data, along with the downlinked altitude data (from an onboard Mode-C transponder), to derive an expanded set of data which includes airspeed, lift, thrust-drag, attitude angles (pitch, roll, and heading), etc. This method of analyzing aircraft motions was evaluated through flight experiments which used the CV-990 research aircraft and recordings from both the enroute and terminal ATC radar systems. The results indicate that the values derived from the ATC radar records are for the most part in good agreement with the corresponding values obtained from airborne measurements. In an actual accident, this analysis of ATC radar records can complement the flight-data recorders, now onboard airliners, and provide a source of recorded information for other types of aircraft that are equipped with Mode-C transponders but not with onboard recorders.

Wingrove, R. C.↗
NASA NTRS1981

Research on electrical properties of severe thunderstorms in the Great Plains

Techniques, equipment, and results of studies (1978-1980) to determine the relationships between electrical phenomena and the dynamics and precipitation of storms are reported. Doppler and conventional radar, video tapes and movies, and VHF recording devices were used to monitor an area 200 x 100 km, aligned SW to NE. The 23 cm radar and a Doppler radar were employed to acquire radar echoes from lightning. Observations of a squall line, a severe storm, and radar echoes from electrical discharges are described. Positively charged cloud-to-ground lightning was observed during the severe and final stages of severe storms; average lightning rates and total flashes for normal and severe storms are provided. Comparisons of lightning echoes and electric field changes indicated that abrupt increases in radar reflectivity were correlated with return strokes and K-type field changes.

Rust, W. D.↗
NASA NTRS2004

Penetration of High Intensity Radiated Fields (HIRF) Into General Aviation Aircraft

The ability to design and achieve electromagnetic compatibility is becoming more challenging with the rapid development of new electronic products and technologies. The importance of electromagnetic interference (EMI) and electromagnetic compatibility (EMC) issues stems from the fact that the ambient electromagnetic environment has become very hostile; that is, it increases both in density and intensity, while the current trend in technology suggests the number of electronic devices increases in homes, businesses, factories, and transportation vehicles. Furthermore, the operating frequency of products coming into the market continuously increases. While cell phone technology has exceeded 1 GHz and Bluetooth operates at 2.4 GHz, products involving satellite communications operate near 10 GHz and automobile radar systems involve frequencies above 40 GHz. The concern about higher frequencies is that they correspond to smaller wavelengths, therefore electromagnetic waves are able to penetrate equipment enclosure through apertures or even small cracks more easily. In addition, electronic circuits have become small in size, and they are usually placed on motherboards or housed in boxes in very close proximity. Cosite interference and coupling in all electrical and electronic circuit assemblies are two essential issues that have to be examined in every design.

Balanis, Constantine A.↗
NASA NTRS2020

UAS Integration in the NAS Project: Overview of Flight Test Series 6

The National Aeronautics and Space Administration (NASA) Unmanned Aircraft Systems Integration in the National Airspace System (UAS-NAS) Project has conducted a series of flight test campaigns intended to support the reduction of barriers that prevent unmanned aircraft from flying without the required waivers from the Federal Aviation Administration (FAA). The 2019 Flight Test Series 6 (FT6) campaign furthered this path and supported three test configurations: 1) Radar Characterization, 2) Scripted Encounters and 3) Full Mission. Radar Characterization assessed the performance of Honeywell’s low size, weight, and power (low SWaP) radar system; Scripted Encounters investigated the timing of Detect and Avoid (DAA) alerting thresholds using a Department of Defense (DoD) Group 3 unmanned aircraft system (UAS) equipped with low SWaP sensors and three different live intruder aircraft flown at varying encounter geometries; and Full Mission validated human-in-the-loop simulations by collecting pilot performance data from a ground control station while controlling a live unmanned aircraft on a mission in both virtual and live air traffic controlled airspace. The subject pilot observed a research display that presented DAA advisories to maintain separation from live and virtual aircraft. The test was conducted over a twenty-week period within the R-2508 special use airspace located near Edwards Air Force Base (EAFB), CA. Over 240 encounters were flown during the test series and FT6 proved to be invaluable for the purposes of planning, managing, and executing this type of integrated flight test in both live and virtual environments. Data collected from FT6 was provided to the RTCA Special Committee 228 (SC-228) to help inform the Phase 2 Minimum Operational Performance Standards (MOPS). FT6 was the final test series for the UAS-NAS project that began in 2012. This paper provides an overview of FT6 and its success can be directly attributed to the diligent work of the men and women who supported this effort.

UAS in the NAS↗
NASA NTRS1988

The Laboratory for Oceans Computing Facility

The first VAX computer in the Laboratory for Oceans Computing Facility (LOCF) was installed and the facility was largely expanded. The growth is not only in hardware and software, but also in the number of users and in supporting research and development projects. The LOCF serves as a general purpose computing facility for: ocean color research projects, sea ice research projects, processing of the Nimbus-7 Coastal Zone Color Scanner data set, real time ingest and analysis of TIROS-N satellite data, study of the Synthetic Aperture Radar data, study of LANDSAT data, and many others. The physical space and the electrical power layout of the computing room were modified to accommodate all the equipment. The LOCF has several image processing stations which include two International Imaging Systems (IIS) model 75 processors and one Adage processor. The facility has the capability of ingesting the TIROS-N HRPT satellite data on a real time basis. More than 30 software packages were installed on the systems. System software packages, network software, FORTRAN and C compilers, database management software, image processing software, graphics, mathematics and statistics packages, TAE, Catalog Manager, GEMPAK, LAS and many other software developed on the LOCF computers such as SEAPAK have greatly advanced the capability of the LOCF.

Kao, R.↗
NASA NTRS2014

A User Guide for Smoothing Air Traffic Radar Data

Matlab software was written to provide smoothing of radar tracking data to simulate ADS-B (Automatic Dependent Surveillance-Broadcast) data in order to test a tactical conflict probe. The probe, called TSAFE (Tactical Separation-Assured Flight Environment), is designed to handle air-traffic conflicts left undetected or unresolved when loss-of-separation is predicted to occur within approximately two minutes. The data stream that is down-linked from an aircraft equipped with an ADS-B system would include accurate GPS-derived position and velocity information at sample rates of 1 Hz. Nation-wide ADS-B equipage (mandated by 2020) should improve surveillance accuracy and TSAFE performance. Currently, position data are provided by Center radar (nominal 12-sec samples) and Terminal radar (nominal 4.8-sec samples). Aircraft ground speed and ground track are estimated using real-time filtering, causing lags up to 60 sec, compromising performance of a tactical resolution tool. Offline smoothing of radar data reduces wild-point errors, provides a sample rate as high as 1 Hz, and yields more accurate and lag-free estimates of ground speed, ground track, and climb rate. Until full ADS-B implementation is available, smoothed radar data should provide reasonable track estimates for testing TSAFE in an ADS-B-like environment. An example illustrates the smoothing of radar data and shows a comparison of smoothed-radar and ADS-B tracking. This document is intended to serve as a guide for using the smoothing software.

Center/Tracon Radar↗
NASA NTRS1987

Rectification of terrain induced distortions in radar imagery

This paper describes a technique to generate geocoded synthetic aperture radar (SAR) imagery corrected for terrain induced geometric distortions. This algorithm transforms the raw slant range image, generated by the signal processor, into a map registered product, resampled to either Universal Transverse Mercator (UTM) or Polar Stereographic projections, and corrected for foreshortening. The technique utilizes the space platform trajectory information in conjunction with a digital elevation map (DEM) of the target area to generate an ortho-radar map with near-autonomous operation. The current procedure requires only two to three tie-points to compensate for the platform position uncertainty that results in translational error between the image and the DEM. This approach is unique in that it does not require generation of a simulated radar image from the DEM or a grid of tie-points to characterize the image-to-map distortions. Rather, it models the inherent distortions based on knowledge of the radar data collection characteristics, the signal Doppler parameters, and the local terrain height to automatically predict the registration transformation. This algorithm has been implemented on a minicomputer system equipped with an array processor and a large random-access memory to optimize the throughput.

Kwok, Ronald↗
NASA NTRS1992

Onboard System Processes SAR Data

Aircraft Flight Correlator (AFC) computing system, mounted with AIRSAR synthetic-aperture-radar (SAR) system, supplements recording and postflight analysis, processing portion of data in real or nearly real time to provide imagery for rapid evaluation. Facilitates diagnosis of SAR equipment or adjustment of parameters of experiment. Operates in two modes: "quick-look" mode, data processed in 10 minutes into high-resolution image; and "real-time" mode, data processed in real time to reduced resolution. Also used as aid to navigation.

Carande, Richard E.↗
NASA NTRS2017

High Ice Water Concentrations in the 19 August 2015 Coastal Mesoconvective System

During August 2015, NASA's DC-8 research aircraft was flown into High Ice Water Content (HIWC) events as part of a three-week campaign to collect airborne radar data and to obtain measurements from microphysical probes. Goals for this flight campaign included improved characterization of HIWC events, especially from an airborne radar perspective. This paper focuses on one of the flight days, in which a coastal mesoscale convective system (MCS) was investigated for HIWC conditions. The system appears to have been maintained by bands of convection flowing in from the Gulf of Mexico. These convective bands were capped by a large cloud canopy, which masks the underlying structure if viewed from an infrared sensing satellite. The DC-8 was equipped with an IsoKinetic Probe that measured ice concentrations of up to 2.3 g m(exp -3) within the cloud canopy of this system. Sustained measurements of ice crystals with concentrations exceeding 1 g m(exp -3) were encountered for up to ten minutes of flight time. Airborne Radar reflectivity factors were found to be weak within these regions of high ice water concentrations, suggesting that Radar detection of HIWC would be a challenging endeavor. This case is then investigated using a three-dimensional numerical cloud model. Profiles of ice water concentrations and radar reflectivity factor demonstrate similar magnitudes and scales between the flight measurements and model simulation. Also discussed are recent modifications to the numerical model's ice-microphysics that are based on measurements during the flight campaign. The numerical model and its updated ice-microphysics are further validated with a simulation of a well-known case of a supercell hailstorm measured during the Cooperative Convective Precipitation Experiment. Differences in HIWC between the continental supercell and the coastal MCS are discussed.

Proctor, Fred H.↗
NASA NTRS2015

Appendix A: NAS-Wide Encounter Rate Evaluation Using Historical Radar Data and the Airspace Concept Evaluation System (ACES)

Regulations that establish operational and performance requirements for unmanned aircraft systems (UAS) are being developed by a consortium of government, industry and academic institutions. Those requirements will apply to detect-and-avoid (DAA) systems and other equipment necessary to integrate UAS with the National Airspace System (NAS) and are determined according to their contribution to the overall level of safety required to operate in the airspace. Several key gaps must be addressed in order to link equipment requirements to an airspace level of safety. Foremost among these is the calculation of the relative effectiveness of a particular system to mitigate violations of a separation standard with other aircraft, which is known as the systems risk ratio. The risk ratio is calculated as the probability of mid-air collision with a DAA system divided by the probability of mid-air collision without a DAA system. The risk ratio of a DAA system, in combination with the risk ratios of other collision avoidance mitigations, will determine the overall safety of the airspace measured in terms of the number of mid-air collisions per flight hour. Defining the required risk ratio that the DAA system needs to ensure the safety of the airspace requires an evaluation of the current airspace and a simulated evaluation that incorporates UAS aerodynamic performance and the mission characteristics of future UAS operations that are projected to be conducted in areas that interact with current operations. These evaluations will produce the frequency of encounters that currently exist in the airspace and those that could be generated with the introduction of UAS. Together, the frequency of encounters, an evaluation of unmitigated risk of collision, and a desired level of safety of the airspace will yield a required risk ratio of the DAA system. This study will focus on evaluating the encounter rates between aircraft based on historical radar data and encounter rates that could occur based on simulated UAS missions.

Unmanned Aircraft Systems↗
NASA NTRS1976

DSN research and technology support

Continuing remote controlled pulsar observations are noted, along with routine observations of 22 pulsars. Preliminary installation of equipment for planned unattended operation of the Venus Station is reported, along with extensive measurements and performance evaluation of the 26-m antenna. Support of the X-band radar at the Mars Station (DSS 14), and stability and reliability testing of the DSS 13 receiving system is reported. Klystron testing and other DSN support activities of the DSN High-Power Transmitter Maintenance Facility are noted, along with energy conservation modifications to two buildings at DSS 13. Radio Science experiment support included Planetary Radio Astronomy, Pulsar Rotation Constancy, Interstellar Microwave Spectroscopy, and Very Long Baseline Interferometry observations. An increased schedule of clock synchronization transmissions, planned on five-day centers, is noted, as 39 transmissions were made to Australia, DSS 43, and Spain, DSS 63.

Jackson, E. B.↗
NASA NTRS1981

A Loran-C prototype navigation receiver for general aviation

Investigations have been conducted regarding the techniques required for Loran-C navigation with application to the general-aviation pilot. The goal has been to produce prototype equipment for flight evaluation which will provide enroute navigation in both latitude-longitude and rho-theta coordinates and to evaluate the nonprecision approach capabilities of such equipment. In connection with the considered project, a prototype Loran-C receiver has been flight-tested using a variety of flight paths, with and without simultaneous ground radar position data collection. Attention is given to a receiver overview, an antenna preamplifier/coupler, the Loran-C receiver RF processor, the tracking loop hardware, tracking loop programming, video output, the laboratory and flight evaluation, and work currently in progress.

Lilley, R. W.↗
NASA NTRS1984

CDTI target selection criteria

A Cockpit Display of Traffic Information (CDTI) is a cockpit instrument which provides information to the aircrew on the relative location of aircraft traffic in the vicinity of their aircraft (township). In addition, the CDTI may provide information to assist in navigation and in aircraft control. It is usually anticipated that the CDTI will be integrated with a horizontal situation indicator used for navigational purposes and/or with a weather radar display. In this study, several sets of aircraft traffic data are analyzed to determine statistics on the number of targets that will be displayed on a CDTI using various target selection criteria. Traffic data were obtained from an Atlanta Terminal Area Simulation and from radar tapes recorded at the Atlanta and Miami terminal areas. Results are given in the form of plots showing the average percentage of time (or probability) that an aircraft equipped with a CDTI would observe from 0 to 10 other aircraft on the display for range settings on the CDTI up to 30 n. mi. and using various target discrimination techniques.

Britt, C. L.↗
NASA NTRS1972

An investigation of vehicle dependent aspects of terminal area ATC operation.

Description of a terminal area simulation which permits analysis and synthesis of current and advanced air traffic management system configurations including ground and airborne instrumentation and new and modified aircraft characteristics. Ground elements in the simulation include navigation aids, surveillance radars, communication links, air-route structuring, ATC procedures, airport geometries, and runway handling constraints. Airborne elements include traffic samples with individual aircraft performance and operating characteristics and aircraft navigation equipment. The simulation also contains algorithms for conflict detection, conflict resolution, sequencing and pilot-controller data links.

Britt, C. L., Jr.↗