SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A simulation is described of a proposed microwave reflectance measurement in which the half scale reflector is used in a compact range type of application. The simulation is used to determine an acceptable aperture taper for the reflector which will allow for accurate measurements. Information on the taper is used in the design of a feed for the reflector.
Segmented reflectors have been proposed for space based applications such as optical communication and large diameter telescopes. An actuation system for mirrors in a space based segmented mirror array was developed as part of NASA's Precision Segmented Reflector program. The actuation system, called the Articulated Panel Module (APM), provides 3 degrees of freedom mirror articulation, gives isolation from structural motion, and simplifies space assembly of the mirrors to the reflector backup truss. A breadboard of the APM was built and is described.
Control analysis activities related to the development of figure control technologies for large space telescopes with precision segmented actively controlled primary reflectors are reviewed. The Precision Segmented Reflector (PSR) configuration is described along with the development and use of the PSR models. Geometric and dynamic models, characterization of figure estimation errors and optimal sensor placement, and the development of quasi-static and dynamic control concepts are outlined. The structure of a quasi-static controller is presented, that utilizes edge sensor measurements to estimate displacement errors at the actuator level and generates figure correction commands. The second approach considers decentralization of the reflector system at the panel level, while the third considers decentralization at the actuator level.
GaAs/AlGaAs single quantum well lasers with integrated corner reflectors have been fabricated using chemically assisted ion beam etching. The air-GaAs interface is internally totally reflecting, and no coherent radiation is transmitted through the corner reflector. The corner reflector laser was compared with a conventional Fabry-Perot laser cleaved from the same wafer. An 11-percent reduction in threshold current and a reduction of the far-field angle from 4.4 deg to 0.7 deg was measured.
Proposed actuation system maintains alignments of reflector segments of large telescope. Sensors measure positions and orientations of segments. Figure-control computer calculates orientation and figure of overall reflector surface from sensor data. Responding to computer output, servocontroller for each actuator corrects piston and tilt errors of each segment. Actuators adjust segments in response to sensed positions. Concept applicable to such large segmented space-based reflectors as those used in communication and in collection of solar energy.
A corrugated horn was designed and fabricated for use as a feed for the half-scale accurate antenna reflector. This feed allows the reflector to be used in a compact range configuration as part of a microwave reflectance measuring system. The horn design is described, and the measured farfield patterns of the horn are presented. The horn was installed at the focus of the reflector, and the nearfield of the antenna was measured. The results of these measurements are presented and discussed with respect to the compact range application.
Two approaches to design a tri-band reflector antenna for the Advanced TDRSS are examined. Two reflector antenna configurations utilizing frequency selective surfaces for operation in three frequency bands, S, Ku, and Ka, are proposed. Far-field patterns and the antenna feed losses were computed for each configuration. An offset-fed single reflector antenna configuration was adapted for conceptual spacecraft design. CADAM drawings were completed and a 1/13th scale model of the spacecraft was constructed.
Science Applications International Corporation (SAIC) investigated the feasibility of producing solar reflectors from indigenous lunar materials for solar power production on the moon. First, lunar construction materials and production processes were reviewed, and candidate materials for reflector production were identified. At the same time, lunar environmental conditions were reviewed for their effect on production of concentrators. Next, conceptual designs and fabrication methods were proposed and studied for production of dish concentrators and heliostats. Finally, fabrication testing was performed on small-scale models using earth analogs of lunar materials. Findings from this initial investigation indicate that production of concentrators from lunar materials may be an attractive approach for solar energy production on the moon. Further design and testing are required to determine the best techniques and approaches to optimize this concept. Four materials were identified as having high potential for solar reflector manufacture. These baseline materials were foamed glass, concrete with glass-fiber reinforcement, a glass-fiber/glass-melt composite, and an iron-glass sintered material.
In an earlier paper by Galindo-Israel et al. (1987), the geometrical optics (GO) principles, constraints, and requirements of the dual- and single-offset-shaped reflector synthesis problem were collected and developed into a set of nonlinear first-order PDEs. An extension of the methods by which solutions to the PDEs can be obtained is presented, together with several case examples. These examples are independently analyzed by GO and physical optics diffraction methods. The starting point for the integration over each reflector can be taken on the outer rim, at the center, or at an intermediate point-the intermediate starting point being the more general case. The utility of the speed of this synthesis method is demonstrated. For example, the program utilized completes a synthesis in less than 45 s on a 386/20 personal computer and within a fraction of a second on a mainframe Cray. This makes practical the incorporation of the synthesis into a search algorithm that can optimize one or more parameters of the reflector system. As an example, the optimization of the mapping equations for low cross polarization is discussed.
A structural verification program applied to qualifying two heritage composite antenna reflectors for flight on the TOPEX satellite is outlined. The verification requirements and an integrated analyses/test approach employed to meet these requirements are described. Structural analysis results and qualification vibration test data are presented and discussed. It was determined that degradation of the composite and bonding materials caused by long-term exposure to an uncontrolled environment had not severely impaired the integrity of the reflector structures. The reflectors were assessed to be structurally adequate for the intended TOPEX application.
Electronic compensation of reflector surface distortion using array feed with individual amplitude and phase control of the array elements is becoming increasingly attractive because of the recent advances in monolithic microwave integrated circuit (MMIC) technology. An algorithm has been developed previously using the concept of focal plane conjugate field matching in the receive mode and a computer code has been generated that predicts the proper excitation coefficients for the elements of the reflector feed array to compensate the effects of reflector surface distortion. This paper presents the results of an experimental study to verify the above compensation algorithm and in general to demonstrate the effectiveness of the array feed compensation technique.
This report presents results of tests performed in neutral buoyancy by two pressure-suited test subjects to simulate Extravehicular Activity (EVA) tasks associated with the on-orbit construction and repair of a precision reflector spacecraft. Two complete neutral buoyancy assemblies of the test article (tetrahedral truss with three attached reflector panels) were performed. Truss joint hardware, two different panel attachment hardware concepts, and a panel replacement tool were evaluated. The test subjects found the operation and size of the truss joint hardware to be acceptable. Both panel attachment concepts were found to be EVA compatible, although one concept was judged by the test subjects to be considerably easier to operate. The average time to install a panel from a position within arm's reach of the test subjects was 1 min 14 sec. The panel replacement tool was used successfully to demonstrate the removal and replacement of a damaged reflector panel in 10 min 25 sec.
One of the critical technology needs of large precision reflectors for future astrophysical and optical communications satellites lies in the area of structural materials. Results from a materials research and development program at NASA Langley Research Center to provide materials for these reflector applications are discussed. Advanced materials that meet the reflector panel requirements are identified, and thermal, mechanical and durability properties of candidate materials after exposure to simulated space environments are compared. A parabolic, graphite-phenolic honeycomb composite panel having a surface accuracy of 70.8 microinches rms and an areal weight of 1.17 lbm/sq ft was fabricated with T50/ERL1962 facesheets, a PAEI thermoplastic surface film, and Al and SiO(x) coatings.
Results are presented of a thermal design optimization study of the segmented GFRP primary reflector of the earth-orbiting Submillimeter Imager and Line Survey telescope. The paper examines the thermal requirements of the primary reflector and the thermal environment of the telescope and describes the thermal design of the primary reflector. Particular attention is given to the geometric math model and the thermal math model of the telescope. A summary for the steady-state thermal performance of the optimized design is presented, showing that the optimized design has reduced, by an order of magnitude, structural spatial temperature gradients, which were earlier shown to be the most significant obstacle in maintaining the required telescope figure accuracy.
Segmented reflectors have been proposed for space-based applications such as optical communication and large-diameter telescopes. An actuation system for mirrors in a space-based segmented mirror array has been developed as part of the National Aeronautics and Space Administration-sponsored Precision Segmented Reflector program. The actuation system, called the Articulated Panel Module (APM), articulates a mirror panel in 3 degrees of freedom in the submicron regime, isolates the panel from structural motion, and simplifies space assembly of the mirrors to the reflector backup truss. A breadboard of the APM has been built and is described. Three-axis modeling, analysis, and testing of the breadboard is discussed.
Report describes proposed laser metrology system in far-infrared telescope with segmented primary reflector. Telescope to be flown in outer space and used to observe celestial objects. Laser metrology system mounted on structure that supported secondary telescope reflector and measures relative positions and alignments of segments of primary reflector. System used in pointing as well as in maintaining surface figure.
Frequency selective subreflectors (FSS) are often employed in the reflector antenna system of a communication satellite or a deep space exploration vehicle for multi-frequency operations. In the past, FSS's have been designed for diplexing two frequency bands. For example, the Voyager FSS was designed to diplex S and X bands and the TDRSS FSS was designed to diplex S and Ku bands. Recently, NASA's CASSINI project requires an FSS to multiplex four frequency (S/X/Ku/Ka) bands. Theoretical analysis and experimental verifications are presented for a multi-band flat pannel FSS with double-ring elements. Both the exact formulation and the thin-ring approximation are described for analyzing and designing this multi-ring patch element FSS. It is found that the thin-ring approximation fails to predict the electrically wide ring element FSS's performance. A single screen double-ring element FSS is demonstrated for the tri-band system that reflects the X-band signal while transmitting through the S- and Ku-band signals. In addition, a double screen FSS with non-similar double-ring elements is presented for the Cassini's four-band system which reflects the X- and Ka-band signals while passing the S- and Ku-band signals. To accurately predict the FSS effects on a dual reflector antenna's radiation pattern, the FSS subreflector's transmitted/reflected field variation as functions of the polarization and incident angles with respect to the local coordinates was taken into account. An FSS transmission/reflection coefficient table is computed for TE and TM polarizations at various incident angles based on the planar FSS model. Next, the hybrid Geometric Optics (GO) and Physical Optics (PO) technique is implemented with linearly interpolating the FSS table to efficiently determine the FSS effects in a dual reflector antenna.
In 1987 a NASA panel recommended the creation of the Mission to Planet Earth. This mission was intended to apply to remote sensing experience of the space community to earth remote sensing to enhance the understanding of the climatological processes of our planet and to determine if, and to what extent, the hydrological cycle of Earth is being affected by human activity. One of the systems required for the mission was a wide scanning, high gain reflector antenna system for use in radiometric remote sensing from geostationary orbit. This work describes research conducted at Virginia Tech into techniques for beam scanning offset Cassegrain reflector antennas by subreflector translation and rotation. Background material relevant to beam scanning antenna systems and offset Cassegrain reflector antenna system is presented. A test case is developed based on the background material. The test case is beam scanned using two geometrical optics methods of determining the optimum subreflector position for the desired scanned beam direction. Physical optics far-field results are given for the beam scanned systems. The test case system is found to be capable of beam scanning over a range of 35 half-power beamwidths while maintaining a 90 percent beam efficiency or 50 half-power beamwidths while maintaining less than l dB of gain loss during scanning.