Search NASA⌕ Search

SEARCH · Search NASA

Results for “REFRACTORY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Development of a Test Technique to Determine the Thermal Conductivity of Large Refractory Ceramic Test Specimens

A method has been developed to utilize the High Intensity Infrared lamp located at Oak Ridge National Laboratory for the measurement of thermal conductivity of bulk refractory materials at elevated temperatures. The applicability of standardized test methods to determine the thermal conductivity of refractory materials at elevated temperatures is limited to small sample sizes (laser flash) or older test methods (hot wire, guarded hot plate), which have their own inherent problems. A new method, based on the principle of the laser flash method, but capable of evaluating test specimens on the order of 200 x 250 x 50 mm has been developed. Tests have been performed to validate the method and preliminary results are presented in this paper.

36 MATERIALS SCIENCE↗

MRP: Design Rules for Refractory Metals

Presentation on Design rules for refractory metals to be given at the Joint ART Materials/AMMT Program Review at DOE Headquarters, Germantown, MD, June 5-8, 2023. Includes microreactor program work for structural materials, failure points of interest, technology, technology maturation and de-risk designs, refractory metals, plan for developing code case as prototype by advanced reactor developers which meets design requirements, and also provides ASME Section III rules.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Non-Classical Creep Behavior of Fusion-Cast Alumina Refractories

The compressive creep behavior of a typical 50% -/50% -alumina fusion-cast refractory block was examined as a function of temperature. Test temperatures (1450-1650oC) were chosen to correspond to those typical of service conditions, while relatively high compressive test stresses (0.6 and 1.0 MPa compared to 0.2-0.4 MPa which is typical of service) were chosen to promote exaggerated deformation and to more accurately measure the resulting creep strain. It was found that the measured creep strain responses in this alumina were a sum of (contracting) compressive creep strain and expansion strain due to time and temperature dependent microcracking. Long term, isothtermal expansion tests were also conducted, and their results allowed for the deconvolution of the compressive creep and expansion strains present in the measured creep strain test data. The analysis shows that despite complications associated with conflicting expansion and contraction effects, classical creep analysis may be used with this alumina refractory after the strains associated with the non-steady-state mechanism are considered and accounted for.

36 MATERIALS SCIENCE↗

Bi‐Continuous W‐Rich Refractory High Entropy Alloy‐Cu Composite: Toward Material Innovation of Nuclear Reactor Coolant System

Abstract Refractory high‐entropy alloys (RHEAs) are considered promising candidate materials for next‐generation nuclear reactors due to their superior mechanical strength, irradiation resistance, and thermal stability at high temperatures. However, the significant positive heat of mixing between refractory alloying elements and Cu, commonly used in cooling systems, poses challenges in forming composite structures. This study addresses the issue using a liquid metal dealloying (LMD) process. A precursor alloy (WTaVTi) with a directional dendrite‐interdendrite structure is fabricated and reacted with molten Cu at 1200 °C for 96 h. This approach produced a RHEA‐Cu composite with a stable interface between RHEA (W 31.5 Ta 30.9 V 21.4 Ti 14.3 ) and Cu, featuring a spontaneously formed W‐rich interlayer that enhances interfacial bonding. The composite showed excellent irradiation resistance, with 30% less swelling under α‐ion irradiation than pure W. It also exhibited low thermal conductivity at room temperature, but reached ≈120 W m −1 ·K −1 at ≈650 °C, surpassing pure W. This temperature‐dependent rise in κ, with a positive gradient of +0.075 W m −1 ·K − 2 , is attributed to decreasing diffuse mismatch at elevated temperatures. The large‐scale reaction and stable microstructure achieved through LMD process highlight its industrial potential. This work offers a strategy for developing high‐performance materials by combining RHEA's radiation resistance with Cu's thermal conductivity for extreme environments.

Chemistry↗

Use of Refractory-Volatile Element Deep Eutectic Regions to Grow Single Crystalline Intermetallic Compounds

Compounds containing both refractory and volatile elements present a unique challenge for crystal growth, given the conflicting realities of high melting temperatures and high vapor pressures. Nevertheless, the discovery of superconductivity in FeAs and FeSe based materials and a Weyl semimetal state in TaP are motivations to explore compounds containing such pairs. Here, we discuss use of the low-melting single phase liquid regions above deep M-X eutectics (M=transition metal, X=P, S) as the basis for high temperature solutions for growing intermetallic compounds containing volatile-refractory pairs. We show that Ni-P, Pd-P, Pt-P, and Pd-S compositions form single phase melts at moderate temperatures below 1000 °C and with minimal vapor pressure. We first present the simple case of growing Ni 2 P from Ni-P and next discuss the more complicated growth of RPd 3 S 4 (R=La, Ce, Nd, Eu) from a Pd-S melt. We show how frit-disc alumina crucible sets allow for contamination-free capture of decanted liquid and its reuse in subsequent experiments, demonstrating a fractionation of the CePd 3 S 4 growth to determine the optimal conditions for crystal growth. We conclude by using the single phase liquid regions above the Pt-P and Pd-P eutectics to grow single crystals of MPt 5 P (M=Mn, Fe) and MnPd 5 P. As these materials have primarily been studied in polycrystalline form, we give an overview of the magnetic and transport properties of our single crystals. The examples outlined here illustrate the utility of using the single phase liquid above deep metal-X eutectics for solution growth and materials discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Management of Transjugular Intrahepatic Portosystemic Shunt (TIPS)-associated Refractory Hepatic Encephalopathy by Shunt Reduction Using the Parallel Technique: Outcomes of a Retrospective Case Series

Purpose: To investigate the reproducibility and technical and clinical success of the parallel technique of transjugular intrahepatic portosystemic shunt (TIPS) reduction in the management of refractory hepatic encephalopathy (HE). Materials and Methods: A 10-mm-diameter self-expanding stent graft and a 5-6-mm-diameter balloon-expandable stent were placed in parallel inside the existing TIPS in 8 patients via a dual unilateral transjugular approach. Changes in portosystemic pressure gradient and HE grade were used as primary end points. Results: TIPS reduction was technically successful in all patients. Mean {+-} standard deviation portosystemic pressure gradient before and after shunt reduction was 4.9 {+-} 3.6 mmHg (range, 0-12 mmHg) and 10.5 {+-} 3.9 mmHg (range, 6-18 mmHg). Duration of follow-up was 137 {+-} 117.8 days (range, 18-326 days). Clinical improvement of HE occurred in 5 patients (62.5%) with resolution of HE in 4 patients (50%). Single episodes of recurrent gastrointestinal hemorrhage occurred in 3 patients (37.5%). These were self-limiting in 2 cases and successfully managed in 1 case by correction of coagulopathy and blood transfusion. Two of these patients (25%) died, one each of renal failure and hepatorenal failure. Conclusion: The parallel technique of TIPS reduction is reproducible and has a high technical success rate. A dual unilateral transjugular approach is advantageous when performing this procedure. The parallel technique allows repeat bidirectional TIPS adjustment and may be of significant clinical benefit in the management of refractory HE.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Matched-Pair Comparison of Radioembolization Plus Best Supportive Care Versus Best Supportive Care Alone for Chemotherapy Refractory Liver-Dominant Colorectal Metastases

Purpose: This study was designed to evaluate overall survival after radioembolization or best supportive care (BSC) in patients with chemotherapy-refractory liver-dominant metastatic colorectal cancer (mCRC). Methods: This was a matched-pair comparison of patients who received radioembolization plus BSC or BSC alone for extensive liver disease. Twenty-nine patients who received radioembolization were retrospectively matched with a contemporary cohort of >500 patients who received BSC from 3 centers in Germany. Using clinical databases, patients were initially matched for prior treatments and tumor burden and then 29 patients were consecutively identified with two or more of four matching criteria: synchronous/metachronous metastases, tumor burden, increased ALP, and/or CEA >200 U/ml. Survival was calculated from date of progression before radioembolization or BSC by using Kaplan-Meier analysis. Results: Of 29 patients in each study arm, 16 pairs (55.2%) matched for all four criteria, and 11 pairs (37.9%) matched three criteria. Patients in both groups had a similar performance status (Karnofsky index, median 80% [range, 60-100%]). Compared with BSC alone, radioembolization prolonged survival (median, 8.3 vs. 3.5 months; P < 0.001) with a hazard ratio of 0.3 (95% confidence interval, 0.16-0.55; P < 0.001) in a multivariate Cox proportional hazard model. Treatment-related adverse events following radioembolization included: grade 1-2 fatigue (n = 20, 69%), grade 1 abdominal pain/nausea (n = 14, 48.3%), and grade 2 gastrointestinal ulceration (n = 3, 10.3%). Three cases of grade 3 radiation-induced liver disease were symptomatically managed. Conclusions: Radioembolization offers a promising addition to BSC in treatment-refractory patients for whom there are limited options. Survival was prolonged and adverse events were generally mild-to-moderate in nature and manageable.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Endovascular Management of Refractory Hepatic Encephalopathy Complication of Transjugular Intrahepatic Portosystemic Shunt (TIPS): Comprehensive Review and Clinical Practice Algorithm

Transjugular intrahepatic portosystemic shunt (TIPS) has evolved as an effective intervention for treatment of complications of portal hypertension. The use of polytetrafluoroethylene-covered stents have improved the patency of the shunts and diminished the incidence of TIPS dysfunction. However, TIPS-related refractory hepatic encephalopathy (rHE) poses a significant challenge. Approximately 3–7 % of patients with TIPS develop rHE. Refractory hepatic encephalopathy is defined as a recurrent or persistent encephalopathy despite appropriate medical treatment. Hepatic encephalopathy can be an extremely debilitating complication that profoundly affects quality of life. The approach to management of patients with rHE is complex and typically requires collaboration between different specialties. Liver transplantation is the ultimate treatment for rHE; however, the ongoing shortage of organ donation markedly limits this treatment option. Alternative therapies such as shunt occlusion or reduction can control symptoms and serve as a ‘bridge’ therapy to liver transplantation. Therefore, interventional radiologists play a key role in the management of these patients by offering a variety of endovascular techniques. The purpose of this review is to highlight some of these endovascular techniques and to develop a therapeutic algorithm that can be applied in clinical practice for the management of rHE.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

CT-Guided Superior Vena Cava Puncture: A Solution to Re-Establishing Access in Haemodialysis-Related Central Venous Occlusion Refractory to Conventional Endovascular Techniques

PurposeThe purpose of this technical note is to demonstrate the novel use of CT-guided superior vena cava (SVC) puncture and subsequent tunnelled haemodialysis (HD) line placement in end-stage renal failure (ESRF) patients with central venous obstruction refractory to conventional percutaneous venoplasty (PTV) and wire transgression, thereby allowing resumption of HD.MethodsThree successive ESRF patients underwent CT-guided SVC puncture with subsequent tract recanalisation. Ultrasound-guided puncture of the right internal jugular vein was performed, the needle advanced to the patent SVC under CT guidance, with subsequent insertion of a stabilisation guidewire. Following appropriate tract angioplasty, twin-tunnelled HD catheters were inserted and HD resumed.ResultsNo immediate complications were identified. There was resumption of HD in all three patients with a 100 % success rate. One patient’s HD catheter remained in use for 2 years post-procedure, and another remains functional 1 year to the present day. One patient died 2 weeks after the procedure due to pancreatitis-related abdominal sepsis unrelated to the Tesio lines.ConclusionCT-guided SVC puncture and tunnelled HD line insertion in HD-related central venous occlusion (CVO) refractory to conventional recanalisation options can be performed safely, requires no extra equipment and lies within the skill set and resources of most interventional radiology departments involved in the management of HD patients.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

High temperature millimeter wave radiometric and interferometric measurements of slag-refractory interaction for application to coal gasifiers

Millimeter wave (MMW) radiometry can be used for simultaneous measurement of emissivity and temperature of materials under extreme environments (high temperature, pressure, and corrosive environments) such as in slagging coal gasifiers, where sensors have been identified as a key enabling technology need for process optimization. We present a state-of-the-art dual-channel MMW heterodyne radiometer with active interferometric capability that allows simultaneous radiometric measurements of sample temperature, emissivity, and flow dynamics to over 1873 K. Interferometric capability is supplied via a probe signal originating from the 137 GHz radiometer local oscillator (LO). The interferometric 'video' channels allow measurement of additional parameters simultaneously, such as volume expansion, thickness change, and slag viscosity along with temperature or emissivity. This capability has been used to demonstrate measurement of temperature and simulated coal slag infiltration into a chromia refractory brick sample as well as slag flow down a vertically placed refractory brick. Observed phenomena include slag melting and slumping, slag reboil and foam with oxygen evolution, and eventual failure of the alumina crucible through corrosion by the molten slag. These results show the promise of the MMW system for extracting quantitative and qualitative process parameters from operating slagging coal gasifiers, providing valuable information for process efficiency, control, and increased productivity.

01 COAL, LIGNITE, AND PEAT↗

Tensile Behavior of Electron Beam-Welded and Post-Weld Vacuum-Annealed Nb-10% Hf-1% Ti Refractory Alloy Weldments

Nb-10% Hf-1% Ti refractory alloy is a high performance material extensively used for high temperature applications. Electron beam welding is one of the most widely used techniques to join refractory and reactive alloys. Bigger sizes of nozzles for rocket propulsion applications can be either made through deep drawing and flow turning route or by roll bending and welding route both using sheets/plates as input material for fabrication. The latter is a more economical option for mass production of the hardware using such exotic and expensive alloys. In view of this, both as-welded (AW) coupon and weld plus post-weld vacuum-annealed (AW + VA) coupon have been prepared to study their mechanical behavior. It has been observed that tensile strength and ductility have not been reduced in both these conditions vis-à-vis the base metal, confirming weld efficiency of the alloy to be ~ 100%. Microhardness is found to be 150-160 VHN in the base metal and 200-225 VHN in the weld fusion zone in AW condition, which became uniform (145-155 VHN) throughout the weldment in AW + VA condition. Microstructure of the weldment in AW condition is found to be consisting of grains solidified by epitaxial mode from base metal toward the weld centre. In AW + VA condition, improvement in tensile elongation is observed, which is found to be due to the presence of homogenized grains/more uniform microstructure near the heat-affected zone as compared to the steep gradient in grain size in different zones in the weld in AW condition.

36 MATERIALS SCIENCE↗

Experimental Investigation of the System Nonmetallic Inclusion-Molten Steel-Refractory System at High Temperatures

In continuous casting, the buildup of particles in the flow control system is called clogging. Clogging may be caused by preexisting nonmetallic inclusions attached to the refractory wall, interrupting or disturbing the fluid flow conditions. The interfacial properties of the nonmetallic inclusion-molten steel-refractory system are believed to play a key role in the clogging tendency of selected steel grades in contact with ceramics. The combination of a high-temperature laser scanning confocal microscope (HT-LSCM), which is employed for in situ observation of inclusions’ behavior in the liquid steel or at the steel/ceramic interface, and a high-temperature drop shape analyzer (HT-DSA), which is utilized for contact angle measurements, enabled the investigation of reactions and interactions in the described system at experimental temperatures of approximately 1600 °C. The objective of this study was to develop a method to obtain qualitative information on the deposition of nonmetallic inclusions (NMIs) in the submerged entry nozzle (SEN) during casting. The behavior of solid NMIs from a calcium-treated steel at the interface between liquid steel and Al{sub 2}O{sub 3} or MgO was investigated by means of HT-LSCM. During the test evaluation, inclusions were found to separate at the steel/ceramic interface due to an attractive force. This force increased with the NMIs’ size as well as with the ceramic particle change. The HT-DSA provided contact angle data between molten steel and the ceramic used for implementation into the theoretical capillary force model. A clear correspondence between the estimated and calculated capillary forces was observed. The change in the wettability of the system, as induced by the change in the ceramic from MgO to Al{sub 2}O{sub 3}, showed a reduction of the attractive forces, indicating a weaker separation toward the SEN for the same inclusion type. This study confirmed the strong potential of wettability investigations to predict the clogging tendency of certain steel grades.

36 MATERIALS SCIENCE↗

Temperature-Dependent Configurational Entropy Calculations for Refractory High-Entropy Alloys

The cluster expansion formalism for alloys is used to construct surrogate models for three refractory high-entropy alloys (NbTiVZr, HfNbTaTiZr, and AlHfNbTaTiZr). These cluster expansion models are then used along with Monte Carlo methods and thermodynamic integration to calculate the configurational entropy of these refractory high-entropy alloys as a function of temperature. Many solid solution alloy design guidelines are based on the ideal entropy of mixing, which increases monotonically with N , the number of elements in the alloy. However, our results show that at low temperatures, the configurational entropy of these materials is largely independent of N , and the assumption described above only holds in the high-temperature limit. This suggests that alloy design guidelines based on the ideal entropy of mixing require further examination.

36 MATERIALS SCIENCE↗

Computation of entropies and phase equilibria in refractory V-Nb-Mo-Ta-W high-entropy alloys

Here, we have applied the first-principles phonon method to the refractory V-Nb-Mo-Ta-W high-entropy alloys (HEAs) to predict the major phase separations in the temperature-compositional space and hence the associated entropy changes within the systems, taking into account vibrational, electronic, and configurational contributions to the total entropy. The first-principles calculations covered 178 phases ranging from pure elements, the ordered B2, B32, B2 3 , B2 2 , hR8, hR7, tI6, C15, and D0 3 binary phases, two ordered MoNbTaW quaternary phases, and the partially disordered and completely disordered bcc phases. By sorting their relative phase stabilities with the Dantzig's simplex minimization algorithm, the possibilities of phase separation for the refractory quaternary and quinary HEAs were thermodynamically found in the temperature range of 500e907 K.

36 MATERIALS SCIENCE↗

Lattice distortion in a strong and ductile refractory high-entropy alloy

Here, the maximization of the mixing entropy with the optimal range of enthalpy in high-entropy alloys (HEAs) can promote the formation of a stable single solid-solution phase with the absence of competing intermetallic compounds. The resultant effects, such as lattice distortion, can contribute to excellent mechanical properties, which has motivated numerous efforts to develop and design single-phase HEAs. However, challenges still remain, particularly on quantifying the lattice distortion and relating it to materials properties. In this study, we have developed a NbTaTiV refractory HEA with a single body-centered-cubic (BCC) structure using an integrated experimental and theoretical approach. The theoretical efforts include thermodynamic modeling, i.e., CALculation of PHAse Diagram (CALPHAD). The microstructural evolutions have been investigated by systematic heat-treatment processes. The typical dendrite microstructure was observed, which is caused by the elemental segregation during the solidification in the as-cast condition. The structural inhomogeneity and chemical segregation were completely eliminated by the proper homogenization treatment at 1200 °C for 3 days. The homogeneous elemental distribution was quantitatively verified by the Atom Probe Tomography (APT) technique. Importantly, results indicate that this HEA exhibits the high yield strength and ductility at both room and high temperatures (up to 900 °C). Furthermore, the effects of the high mixing entropy on the mechanical properties are discussed and quantified in terms of lattice distortions and interatomic interactions of the NbTaTiV HEA via first-principles calculations. It is found that the local severe lattice distortions are induced, due to the atomic interactions and atomic-size mismatch in the homogenization-treated NbTaTiV refractory HEA.

36 MATERIALS SCIENCE↗

A review on additive manufacturing of refractory tungsten and tungsten alloys

Here we review the progress of additive manufacturing effort on refractory metal tungsten and tungsten alloys. These materials are excellent candidates for a variety of high temperature applications but extremely challenging to fabricate via additive manufacturing due to a series of existing issues during the manufacturing. We outline these issues and discuss the current understanding and progress to tackle them. Laser powder-bed-fusion, laser directed-energy-deposition, and electron beam powder-bed-fusion are three common techniques that have been applied to additively manufacture pure tungsten. This overview discusses current observations and understanding on the issues associated with each of these techniques. We identify future research opportunities in additive manufacturing of refractory metals.

36 MATERIALS SCIENCE↗

Salvage Gamma Knife Stereotactic Radiosurgery for Surgically Refractory Trigeminal Neuralgia

Purpose: To evaluate the clinical outcome of patients with surgically refractory trigeminal neuralgia (TN) treated with rescue gamma knife radiosurgery (GKRS). Methods and Materials: Seventy-nine patients with typical TN received salvage GKRS between 1997 and 2002 at the Barrow Neurological Institute (BNI). All patients had recurrent pain following at least one prior surgical intervention. Prior surgical interventions included percutaneous destructive procedures, microvascular decompression (MVD), or GKRS. Thirty-one (39%) had undergone at least two prior procedures. The most common salvage dose was 80 Gy, although 40-50 Gy was typical in patients who had received prior radiosurgery. Pain outcome was assessed using the BNI Pain Intensity Score, and quality of life was assessed using the Brief Pain Inventory. Results: Median follow-up after salvage GKRS was 5.3 years. Actuarial analysis demonstrated that at 5 years, 20% of patients were pain-free and 50% had pain relief. Pain recurred in patients who had an initial response to GKRS at a median of 1.1 years. Twenty-eight (41%) required a subsequent surgical procedure for recurrence. A multivariate Cox proportional hazards model suggested that the strongest predictor of GKRS failure was a history of prior MVD (p=0.029). There were no instances of serious morbidity or mortality. Ten percent of patients developed worsening facial numbness and 8% described their numbness as 'very bothersome.' Conclusions: GKRS salvage for refractory TN is well tolerated and results in long-term pain relief in approximately half the patients treated. Clinicians may reconsider using GKRS to salvage patients who have failed prior MVD.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Complete Restoration of Refractory Mandibular Osteoradionecrosis by Prolonged Treatment with a Pentoxifylline-Tocopherol-Clodronate Combination (PENTOCLO): A Phase II Trial

Purpose: Osteoradionecrosis (ORN) is a nonhealing wound of the bone that is difficult to manage. Combined treatment with pentoxifylline and vitamin E reduces radiation-induced fibrosis and ORN with a good prognosis. We previously showed that the combination of pentoxifylline and vitamin E with clodronate (PENTOCLO) is useful in healing sternocostal and some mandibular ORN. Is PENTOCLO effective in ORN of poor prognosis? Methods: 54 eligible patients previously irradiated for head and neck cancer (among 72 treated) a mean 5 years previously received exteriorized refractory mandibular ORN for 1.4 {+-} 1.8 years, mainly after local surgery and hyperbaric oxygen had been ineffective. The mean length of exposed bone (D) was 17 {+-} 8 mm as primary endpoint, and the mean Subjective, Objective, Management, and Analytic evaluation of injury (SOMA) score was 16 {+-} 4. Between August 2000 and August 2008, all patients were given daily oral PENTOCLO: 800 mg pentoxifylline, 1,000 IU vitamin E, and 1,600 mg clodronate 5 days per week alternating with 20 mg prednisone and 1,000 mg ciprofloxacin 2 days per week. The duration of treatment was related to consolidated healing. Results: Prolonged treatment (16 {+-} 9 months) was safe and well tolerated. All patients improved, with an exponential progressive-(f[t] = a.exp(-b.t)-and significant (p < 0.0001) reduction of exposed bone (D), respectively (months): D{sub 2} -42%, D{sub 4} -62%, D{sub 6} -77%, D{sub 12} -92%, and D{sub 18} -96%, combined with iterative spontaneous sequestrectomies in 36 patients. All patients experienced complete recovery in a median of 9 months. Clinical improvement was measured in terms of discontinuation of analgesics, new fracture, closed skin fistulae, and delayed radiologic improvement: SOMA{sub 6} -64%, SOMA{sub 12} -89%, and SOMA{sub 30} -96%. Conclusion: Long-term PENTOCLO treatment is effective, safe, and curative for refractory ORN and induces mucosal and bone healing with significant symptom improvement. These findings will need to be confirmed in a randomized trial.

62 RADIOLOGY AND NUCLEAR MEDICINE↗