Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Wind turbine main bearing rating lives as determined by IEC 61400‐1 and ISO 281: A critical review and exploratory case study

Abstract This paper studies the rating lives of wind turbine main bearings, as determined by the IEC 61400‐1 and ISO 281 standards. A critical review of relevant bearing life theory and turbine design requirements is provided, including discussion on possible shortcomings such as the existence (or not) of the bearing fatigue load limit and the validity of assuming linear damage accumulation. A detailed exploratory case study is then undertaken to determine rating lives for two models of main bearing in a 1.5 MW wind turbine. Rating life assessment is carried out under different conditions, including various combinations of main bearing temperature, wind field characteristics, lubricant viscosity, and contamination levels. Rating lives are found to be sufficiently above the desired 20‐year design life for both bearing models under expected operating conditions. For the larger bearing, operational loads are shown to be below or close to the bearing fatigue load limit a vast majority of the time. Key sensitivities for rating life values are temperature and contamination. Overall, the results of this study suggest that an ISO 281 rating life assessment does not account for reported rates of main bearing failures in 1 to 3 MW wind turbines. It is recommended that a similar analysis be undertaken for ISO/TS 16281 rating lives, along with further efforts to identify principal root causes of main bearing failures in future work, possibly leading to a new application standard specific to this component. It is also recommended that the impacts of partial wake impingement on main bearing rating lives are investigated.

17 WIND ENERGY↗
DOE OSTI2019

Effect of Retained Austininte on White Etching Crack Behavior of Carburized AISI 8620 Steel Under Boundary Lubrication

The formation of white etching cracks (WECs) is a dominant failure mode in wind turbine gearbox bearings that can significantly shorten their operating life. Although the phenomenon of WECs has been communicated in the field for more than a decade, the driving mechanisms are still debated, and the impact of proposed mitigation techniques is not quantified. Leading hypotheses to inhibit the formation of WECs center on material solutions, including the use of steel with high levels of retained austenite (RA). The present work aims to explore the impact of RA on the formation of WECs within AISI 8620 steel under boundary lubrication. A three ring-on-roller benchtop test rig was used to replicate WECs in samples with different levels of RA. While varying levels of RA had a minimal effect on time until failure, a significant effect on crack morphology was observed. Additionally, potential underlying mechanisms of White Etching Area formation were elucidated. Under the current test conditions, the microstructural alterations adjacent to the cracks in the lower RA samples were more developed compared to those of the higher RA samples. Additionally, the WEC networks in the high RA samples contained significantly more crack branches than those of the low RA samples.

Bearing failure↗
DOE OSTI2021

Residual strain-stress in manganese steel railway crossing determined by synchrotron and laboratory X-rays

The residual stress within the nose of a worn manganese steel railway crossing was investigated. The macroscopic residual stress at the running surface was determined in areas with and without visual faults by laboratory X-rays. To get information about the penetration depth of the residual stress, synchrotron X-ray diffraction was used to map the distribution of local (within grain) residual strains below the running surface. The laboratory X-ray measurements revealed significant compressive stress on the rail running surface. The synchrotron measurements documented that local strains exist through the entire depth investigated. Relations between residual stress, plastic deformation, and crack formation are analysed, leading to a discussion on potentials/limitations of the two experimental methods for investigations of residual stress in large engineering components.

differentia aperture synchrotron diffraction↗
DOE OSTI2026

Reductions in wind farm main bearing rating lives resulting from wake impingement

This paper studies the impacts of wake impingement on main bearing rating lives predicted during the wind turbine design stage. A computational tool chain was developed to explore and quantify these effects across a wind farm populated by 10 MW wind turbines. Wind field and turbine load modelling was undertaken using the Dynamiks Python package, including application of a dynamic wake meandering model. The ISO 281 basic bearing rating life formulation was subsequently applied in order to evaluate impacts from wake effects. Analyses included a two-turbine parametric analysis, followed by a full wind farm analysis undertaken for the TotalControl 32-turbine reference wind farm, including full wind rose simulations across all operational wind speeds. Site conditions were accounted for using a Weibull wind speed distribution and a range of parametric wind direction rose models. Results indicate that wind farm main bearing rating lives are negatively impacted by the effects of wake impingement, resulting in rating life reductions for the analysed wind farm of the order of 16 % on average and as much as 20 %–25 %, both for the locating main bearing. Despite these high sensitivities, it is important to note that these resultant rating lives (i.e. the predicted lives) still far exceed the standard wind turbine operational lifetimes of 20–30 years. Wake impacts were also found to be asymmetrically related to the side on which the rotor is impinged, suggesting that, for the main bearing, there may be a “better” side for wake impingement to occur. Rating life sensitivities to wind rose shape were also observed. While these findings must be interpreted with due consideration for the various methodological limitations present, they provide compelling evidence that wake effects at the wind farm level should necessarily be included when undertaking main bearing operational load modelling, rating life assessment, or other load-related analyses.

17 WIND ENERGY↗
NASA NTRS1975

Wear and interfacial transport of material

The paper is a review of adhesion or bonding across an interface between two solids in contact, transfer or transport to one or both surfaces, wear with tangential motion, and the effect of surface films on adhesion, transfer, and wear. The discussion is limited to the case of adhesive wear which deals with the interfacial transport of material from one surface to another. The data presented suggest that the resulting interfacial adhesive bond for metals in contact is generally stronger than the cohesive bond in the cohesively weaker of the two materials so that upon separation of the surfaces transfer will occur from the cohesively weaker material to the cohesively stronger; that with tangential motion of two metal surfaces in contact such as encountered with sliding, rolling, or rubbing contact, the frictional energy can be dissipated in a number of ways, where heating of the surfaces can produce metallurgical changes such as alloying; and that the presence of adsorbed and reacted films on the surface of metals and alloys even in frictions of a monolayer can reduce interfacial bonding, adhesion, and transfer.

Buckley, D. H.↗
NASA NTRS1977

Microstructural and wear properties of sputtered carbides and silicides

Sputtered Cr3C2, Cr3Si2, and MoSi2 wear-resistant films (0.05 to 3.5 microns thick) were deposited on metal and glass surfaces. Electron transmission, electron diffraction, and scanning electron microscopy were used to determine the microstructural appearance. Strong adherence was obtained with these sputtered films. Internal stresses and defect crystallographic growth structures of various configurations within the film have progressively more undesirable effects for film thicknesses greater than 1.5 microns. Sliding contact and rolling element bearing tests were performed with these sputtered films. Bearings sputtered with a duplex coating (0.1-micron-thick undercoating of Cr3Si2 and subsequently 0.6-micron coating of MoS2) produced marked improvement over straight MoS2 films.

Spalvins, T.↗
NASA NTRS1978

The practical impact of elastohydrodynamic lubrication

Elastohydrodynamic lubrication has had its most significant impact on, among all the types of concentrated contact mechanisms, rolling element bearings. EHL technology, through its inclusion in computer codes, now provides us with more effective methods for optimizing bearing design and for predicting bearing life, power loss, temperature and dynamic behavior. Bearing life prediction has advanced to a much more sophisticated level as compared to the calculation of fatigue life based on Lundberg-Palmgren theory. Application of elastohydrodynamics to gearing has, more or less, been limited to the calculation of pitch point film thicknesses. Techniques for calculating film thicknesses over the entire range of tooth meshes for arbitrarily shaped gear teeth (noninvolute, spur, helical, etc.) need to be developed. Elastomer seals with both unidirectional and reciprocating motion offer a fruitful application for the elastohydrodynamics of low modulus materials.

Anderson, W. J.↗
NASA NTRS1990

Spiral lead platen robotic end effector

A robotic end effector is disclosed which makes use of a rotating platen with spiral leads used to impact lateral motion to gripping fingers. Actuation is provided by the contact of rolling pins with the walls of the leads. The use of the disclosed method of actuation avoids jamming and provides excellent mechanical advantage while remaining light in weight and durable. The entire end effector is compact and easily adapted for attachment to robotic arms currently in use.

Beals, David C.↗
DOE OSTI2013

Effects of Surface Modification Conditions on Hydrophobicity of Silica-based Coating Additives

Superhydrophobic silica (SHS) powders are being evaluated as a potential additive to the polyurethane topcoats used in Chemical Agent Resistant Coating (CARC) systems, with the goal of improving water repellency and corrosion protection characteristics. The current generation of CARC topcoats is already highly loaded with solids, and thus there is a premium on minimization of the total SHS powder required to achieve the desired properties. Therefore, efficient surface modification of the silica and proper dispersion in the coating will be required. The effect of a dispersant on the surface modification of silica particles by chlorosilanes was addressed in this study. The properties of various SHS powders were characterized by thermogravimetric analysis and mass spectroscopy. Correlations between powder modification conditions and the ultimate effects of the modified particles on hydrophobicity of CARC topcoats were assessed. The use of contact and rolling angle measurements along with scanning electron microscopy are discussed as they pertain to the ability to quantify the effects of modified silicas on corrosion prevention coatings. Furthermore, a systematic approach to modifying and testing both powders and top coats of corrosion prevention systems is presented.

Armstrong, Beth L↗
NASA NTRS1972

Cross flow in a starved EHD contact

An analysis of lubrication cross flow effects under starved elastohydrodynamic conditions is presented. Starvation is defined as any operating condition such that an increase in oil available to the contact will result in an increase in film thickness. Starved EHD behavior is considered in several situations: (1) when no new oil enters the contact, and (2) when a step change in one of the rolling parameters is introduced at an equilibrium contact. Based on the fact that important oil flow within the Hertz zone is across the rolling contact direction, it is possible to formulate a simple theory which explains quantitatively some aspects of starved ball bearing behavior.

Kingsburg, E. P.↗
NASA NTRS2015

Superelastic Ball Bearings: Materials and Design to Avoid Mounting and Dismounting Brinell Damage in an Inaccessible Press-fit Application-: Detailed Analysis - II

Rolling element bearings utilized in precision rotating machines require proper alignment, preload, and interference fits to ensure overall optimum performance. Hence, careful attention must be given to bearing installation and disassembly procedures to ensure the above conditions are met. Usually, machines are designed in such a way that bearings can be pressed into housings or onto shafts through the races without loading the rolling elements. However, in some instances, either due to limited size or access, a bearing must be installed or removed in such a way that the load path travels through the rolling elements. This can cause high contact stresses between the rolling elements and the races and introduces the potential for Brinell denting of the races. This paper is a companion to the Part I paper by the authors that discusses material selection and the general design philosophy for the bearing. Here, a more in-depth treatment is given to the design of a dent-resistant bearing utilizing a superelastic alloy, 60NiTi, for the races. A common bearing analysis tool based on rigid body dynamics is used in combination with finite element simulations to design the superelastic bearing. The primary design constraints are prevention of denting and avoiding the balls riding over the edge of the race groove during a blind disassembly process where the load passes through the rolling elements. Through an iterative process, the resulting bearing geometry is tailored to improve axial static load capability compared to a deep-groove ball bearing of the same size. The results suggest that careful selection of materials and bearing geometry can enable blind disassembly without damage to the raceways, which is necessary in the current application (a compressor in the International Space Station Environmental Control and Life Support System), and results in potential design flexibility for other applications, especially small machines with miniature bearings.

metals↗