Search NASA⌕ Search

SEARCH · Search NASA

Results for “Range Safety”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Ideal MHD induced temperature flattening in spherical tokamaks

This paper extends the analysis first presented in Jardin et al. [Phys. Rev. Lett. 128, 245001 (2022)] to more thoroughly examine the stability of spherical torus equilibrium to ideal magnetohydrodynamic (MHD) infernal modes and their nonlinear consequences. Here we demonstrate that in a 3D resistive magnetohydrodynamic (MHD) simulation of a NSTX discharge, anomalous transport can occur due to these instabilities. Here we generate a family of equilibrium of differing β and use this to show that these instabilities could explain the experimentally observed flattening of the electron temperature profile at modest β. The modes studied in this paper are found to occur with poloidal mode number m and toroidal mode number n when the ratio m/ n is in the range of 1.2–1.5, when the central safety factor is in this range or slightly lower, and when the central region has very low magnetic shear. Our analysis gives some insight as to why the unstable linear growth rates are oscillatory functions of the toroidal mode number n. We present a simulation of an initially stable configuration that passes through a stability boundary at a critical β as it is heated. We also show that a particular NSTX discharge is unstable to these modes over a timescale of several hundred ms. We conclude that these modes must be taken into account when performing predictive modeling. An appendix shows that similar modes can be found in R / a = 4 tokamaks for certain q-profiles and β values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2003

Space Based Communications

Current space lift launches on the Eastern and Western Range require extensive ground-based real-time tracking, communications and command/control systems. These are expensive to maintain and operate and cover only limited geographical areas. Future spaceports will require new technologies to provide greater launch and landing opportunities, support simultaneous missions, and offer enhanced decision support models and simulation capabilities. These ranges must also have lower costs and reduced complexity while continuing to provide unsurpassed safety to the public, flight crew, personnel, vehicles and facilities. Commercial and government space-based assets for tracking and communications offer many attractive possibilities to help achieve these goals. This paper describes two NASA proof-of-concept projects that seek-to exploit the advantages of a space-based range: Iridium Flight Modem and Space-Based Telemetry and Range Safety (STARS). Iridium Flight Modem uses the commercial satellite system Iridium for extremely low cost, low rate two-way communications and has been successfully tested on four aircraft flights. A sister project at Goddard Space Flight Center's (GSFC) Wallops Flight Facility (WFF) using the Globalstar system has been tested on one rocket. The basic Iridium Flight Modem system consists of a L1 carrier Coarse/Acquisition (C/A)-Code Global Positioning System (GPS) receiver, an on-board computer, and a standard commercial satellite modem and antennas. STARS uses the much higher data rate NASA owned Tracking and Data Relay Satellite System (TDRSS), a C/A-Code GPS receiver, an experimental low-power transceiver, custom built command and data handler processor, and digitized flight termination system (FTS) commands. STARS is scheduled to fly on an F-15 at Dryden Flight Research Center in the spring of 2003, with follow-on tests over the next several years.

Simpson, James↗
DOE OSTI2023

Light-duty Plug-in Electric Vehicles in China: Evolution, Competition, and Outlook

China's plug-in electric vehicle (PEV) market with stocks at 7.8 million is the world's largest in 2021, and it accounts for half of the global PEV growth in 2021. The PEV market in China has dramatically evolved since the pandemic in 2020: over 20% of all new PEV sales are from China by mid-2022. Recent features of PEV market dynamics, consumer acceptance, policies, and infrastructure have important implications for both the global energy market and manufacturing stakeholders. From the perspective of demand pull-supply push, this study analyzes China's PEV industry with a market dynamics framework by reviewing sales, product and brand, infrastructure, and government policies from the last few years and outlooking the development of the new government’s 14th Five-Year Plan (2021-2025). From the demand side, small-sized sedans and compact sport utility vehicles with increased electric ranges are both popular for PEVs, and the electric range of over 60% of new battery electric vehicles in 2021 has been longer than 400 km. From the supply side, although foreign brands like Tesla are still competitive, the products by Chinese domestic automakers like BYD are becoming more attractive and cannibalizing the high-end market. However, the production capacity and cost of PEVs may be limited by the upstream of the supply chain – the battery manufacturing and supply chain inflation. In addition, it is also uncertain how much sales demand impacts will be caused by the potential global economic recession. The government firmly supports electrification and decarbonization of the vehicle industry by emphasizing the importance of the vehicle industry for promoting the greenhouse gas net zero by 2060. The dual-credit policy is regarded as the most critical regulation in a bid to restrain fuel consumption and promote PEV share. Still, the market is facing some technological obstacles, such as battery safety and driving range anxiety, before real prosperity. In addition, the Chinese electric vehicle market is seeing a trend toward the development of new technologies such as vehicle-to-X, autonomous driving, and connected vehicles.

Hao, Xu↗
DOE OSTI2021

Current Status and Future Directions of All-Solid-State Batteries with Lithium Metal Anodes, Sulfide Electrolytes, and Layered Ternary Oxide Cathodes

All-solid-state batteries (ASSBs) offer great promise as a next-generation energy storage technology with higher energy density, wider operating temperature range, and improved safety for electric vehicles. ASSBs employing lithium metal anodes (Li), sulfide-based solid-state electrolytes (SSE), and Ni-rich layered transition metal oxide cathodes (LiMO 2 , M = Ni, Mn, Co, Al) are particularly promising due to its superior electrochemical performance compared to other solid-electrolyte systems. However, the battery cycle life at high cathode mass loading and high current is still limited because the failure mechanism is not fully understood. Lithium dendrite growth at the anode or inside a solid electrolyte still represents as a serious risk of cell failure. Interfacial resistance increases attributed to electrolyte decomposition and interfacial void formation at both cathode–electrolyte and anode–electrolyte interfaces lead to gradual capacity fading. In this Review, we present the fundamental challenges and recent scientific understandings of each component in ASSBs. The novel diagnostic tools for these components, especially the interfaces buried under the surface that are often hard for characterization are mainly examined. Lastly, we offer a perspective for future research directions. We hope this Review will provide a timely snapshot of state-of-the-art research progress in ASSBs to accelerate the development of ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗
DOE OSTI2020

Non-contact Current-Voltage (I-V) Tracer for Photovoltaics

This report presents a non-contact approach to simultaneously obtain current-voltage (I-V) curves of photovoltaic (PV) substrings and modules in a string without the need of disconnecting the individual modules from the string. There are two types of I-V curve tracers currently available in the marketplace, capacitor-based and electronic load-based. The primary requirement of these conventional I-V tracers is the disconnection of individual modules in the string so the individual modules contacted through the connectors of the individual modules. These contact-tracers have three major limitations in the utility scale power plants: First limitation – Weather and Accuracy: The mass-produced commercial contact-tracers cannot obtain the I-V curves of both string and its modules (as high as 30 modules), almost simultaneously (within about 5 minutes) at, practically, a single irradiance level, a single module temperature, a single spectrum and a single AOI (angle of incidence). This inability of the contact-tracers forces the testing personnel to wait for an extended or multiple sunny (>800 W/m 2 ) duration(s) of a cloudy day. This is a serious limitation as waiting for the sunny conditions or days is a huge practical challenge in almost all locations, except desert locations. Also, since the I-V curves are obtained at different prevailing weather conditions, it becomes critical to translate all the measured I-V curves of 30 modules in the string to a single test condition, for example STC (standard test conditions), so the underperforming modules can be identified. The accuracy of translation equations is heavily influenced by the irradiance level and temperature, spectral and AOI ranges; Second limitation - Safety: The second limitation is related to the high voltage electrical safety of the test personnel during disconnecting and reconnecting of individual modules or cable connectors from the string under daylight conditions and damaging of the original module connectors (especially the field aged connectors) during the disconnecting and reconnecting process; Third limitation – Labor: The third limitation is related to the enormous amount of time and hardship for the test personnel under prevailing (often harsh) protracted field conditions. This project was executed by Arizona State University in collaboration with its industry partner, PV Measurements Inc. (PVM). To mitigate all the three challenges of the state-of-the-art equipment indicated above, we utilized a non-contact I-V (NCIV) tracer approach. In this approach, we utilized an electrostatic voltmeter (ESV) and voltage sensor/probe combination to obtain I-V curves. The ESV units are extensively used in the high voltage industry but not in the PV industry. To obtain the simultaneous I-V curves of the substrings and modules within a string, we utilized multiple commercial ESV-Probe sets. In this approach, we utilized a non-contact voltage sensor (called, Probe) placed on the glass surface of the module (above the last cell of the module). This probe senses the module voltage (with respect to ground) through measured capacitance which is dictated by the surface charges (which in turn is dictated by the module voltage) and transmits the sensed voltage to the voltmeter (called, ESV or NCV, non-contact voltmeter). The current is sensed by a non-contact hall sensor. In a 30-module string, the 30th probe obtains the entire string I-V along with the string I-V obtained by the electronic load. so that the I-V curves of the substrings and modules can be obtained by NCIV without the need of disconnecting the individual modules in the string. The string I-V curves obtained by the electronic load and NCIV can be compared for the accuracy determination. One can use 30 ESV units and 30 Probes to obtain 30 I-V curves of a 30-module string or use just 5 ESV units and 30 Probes in conjunction with 5 six-channel switchboxes (called, 6:1 switchboxes). To reduce the equipment cost, we utilized the 6:1 switchbox approach so the number of ESV units is reduced from 30 to 5. The approaches, achievements and challenges of this project are detailed in this report.

14 SOLAR ENERGY↗
NASA NTRS1992

Stall-Departure-Resistance Enhancer

Stall-departure-resistance enhancer imposes lesser drag penalty than nortex generators of older types. Increases lift by as much as 30 percent at angles of attack otherwise in poststall region. Device is flat plate wedge with 60 degree sweep angle and attached so it protrudes from leading edge of wing. Tip is sharp point, and edges made thin and sharp to induce good vortical flow. Applications include those intended to increase safety for broad range of aircraft, including trainers, fighters, general-aviation aircraft, and commercial transport aircraft. Nonaerospace applications where flow stall is problem under certain conditions, such as in control of separation in flow diffusers. Other applications in fluid machinery and fluid flow.

Ross, Holly M.↗
NASA NTRS2005

Single-Scale Retinex Using Digital Signal Processors

The Retinex is an image enhancement algorithm that improves the brightness, contrast and sharpness of an image. It performs a non-linear spatial/spectral transform that provides simultaneous dynamic range compression and color constancy. It has been used for a wide variety of applications ranging from aviation safety to general purpose photography. Many potential applications require the use of Retinex processing at video frame rates. This is difficult to achieve with general purpose processors because the algorithm contains a large number of complex computations and data transfers. In addition, many of these applications also constrain the potential architectures to embedded processors to save power, weight and cost. Thus we have focused on digital signal processors (DSPs) and field programmable gate arrays (FPGAs) as potential solutions for real-time Retinex processing. In previous efforts we attained a 21 (full) frame per second (fps) processing rate for the single-scale monochromatic Retinex with a TMS320C6711 DSP operating at 150 MHz. This was achieved after several significant code improvements and optimizations. Since then we have migrated our design to the slightly more powerful TMS320C6713 DSP and the fixed point TMS320DM642 DSP. In this paper we briefly discuss the Retinex algorithm, the performance of the algorithm executing on the TMS320C6713 and the TMS320DM642, and compare the results with the TMS320C6711.

Hines, Glenn↗
NASA NTRS2017

In-Space Chemical Propulsion Systems Roadmap

In-space propulsion begins where the launch vehicle upper stage leaves off, performing the functions of primary propulsion, reaction control, station keeping, precision pointing, and orbital maneuvering. The main engines used in space provide the primary propulsive force for orbit transfer, planetary trajectories and extra planetary landing and ascent. The reaction control and orbital maneuvering systems provide the propulsive force for orbit maintenance, position control, station keeping, and spacecraft attitude control. Advanced in-space propulsion technologies will enable much more effective exploration of our Solar System and will permit mission designers to plan missions to "fly anytime, anywhere, and complete a host of science objectives at the destinations" with greater reliability and safety. With wide range of possible missions and candidate propulsion technologies, the question of which technologies are "best" for future missions is a difficult one. A portfolio of propulsion technologies should be developed to provide optimum solutions for a diverse set of missions and destinations. A large fraction of the rocket engines in use today are chemical rockets; that is, they obtain the energy needed to generate thrust by chemical reactions to create a hot gas that is expanded to produce thrust. A significant limitation of chemical propulsion is that it has a relatively low specific impulse (Is, or thrust per mass flow rate of propellant). A significant improvement (>30%) in Is can be obtained by using cryogenic propellants, such as liquid oxygen and liquid hydrogen, for example. Historically, these propellants have not been applied beyond upper stages.

Oxidizers↗
NASA NTRS2019

Understanding the Impact of Meteorological Spatiotemporal Variability on Distant Focusing Overpressure Risk

Since the 1950s, the amplification of blast energy from explosions has been understood to be a significant hazard to public safety at launch ranges. Historically, the risk assessment of the Distant Focusing Overpressure (DFO) hazard started with a single temperature and wind profile (e.g., a radiosonde launch) as input to acoustic 1-D ray tracing models. By analyzing rays propagation and performing ray tracing, population centers under high DFO risk can be identified. Although this method is useful, less is known about how the blast waves can be focused when the spatiotemporal variability of the input profiles are considered. In summary, this work aims to consider how realistic atmospheric boundary layer variability (e.g., turbulence, land-surface contrasts) may affect blast waves propagation and focusing and, as a result, DFO risk assessment results.

Blumberg, W. Greg↗
NASA NTRS2010

Rationales for the Lightning Flight-Commit Criteria

Since natural and artificially-initiated (or "triggered") lightning are demonstrated hazards to the launch of space vehicles, the American space program has responded by establishing a set of Lightning Flight Commit Criteria (LFCC), also known as Lightning Launch Commit Criteria (LLCC), and associated Definitions to mitigate the risk. The LLCC apply to all Federal Government ranges and similar LFCC have been adopted by the Federal Aviation Administration for application at state-operated and private spaceports. The LLCC and Definitions have been developed, reviewed, and approved over the years of the American space program, progressing from relatively simple rules in the mid-twentieth century (that were inadequate) to a complex suite for launch operations in the early 21st century. During this evolutionary process, a "Lightning Advisory Panel (LAP)" of top American scientists in the field of atmospheric electricity was established to guide it. Details of this process are provided in a companion document entitled "A History of the Lightning Launch Commit Criteria and the Lightning Advisory Panel for America s Space program" which is available as NASA Special Publication 2010-216283. As new knowledge and additional operational experience have been gained, the LFCC/LLCC have been updated to preserve or increase their safety and to increase launch availability. All launches of both manned and unmanned vehicles at all Federal Government ranges now use the same rules. This simplifies their application and minimizes the cost of the weather infrastructure to support them. Vehicle operators and Range safety personnel have requested that the LAP provide a detailed written rationale for each of the LFCC so that they may better understand and appreciate the scientific and operational justifications for them. This document provides the requested rationales

Willett, John C.↗
NASA NTRS1988

NASA's post-Challenger safety program - Themes and thrusts

The range of managerial, technical, and procedural initiatives implemented by NASA's post-Challenger safety program is reviewed. The recommendations made by the Rogers Commission, the NASA post-Challenger review of Shuttle design, the Congressional investigation of the accident, the National Research Council, the Aerospace Safety Advisory Panel, and NASA internal advisory panels and studies are summarized. NASA safety initiatives regarding improved organizational accountability for safety, upgraded analytical techniques and methodologies for risk assessment and management, procedural initiatives in problem reporting and corrective-action tracking, ground processing, maintenance documentation, and improved technologies are discussed. Safety issues relevant to the planned Space Station are examined.

Rodney, G. A.↗
NASA NTRS2014

GPM Timeline Inhibits For IT Processing

The Safety Inhibit Timeline Tool was created as one approach to capturing and understanding inhibits and controls from IT through launch. Global Precipitation Measurement (GPM) Mission, which launched from Japan in March 2014, was a joint mission under a partnership between the National Aeronautics and Space Administration (NASA) and the Japan Aerospace Exploration Agency (JAXA). GPM was one of the first NASA Goddard in-house programs that extensively used software controls. Using this tool during the GPM buildup allowed a thorough review of inhibit and safety critical software design for hazardous subsystems such as the high gain antenna boom, solar array, and instrument deployments, transmitter turn-on, propulsion system release, and instrument radar turn-on. The GPM safety team developed a methodology to document software safety as part of the standard hazard report. As a result of this process, a new tool safety inhibit timeline was created for management of inhibits and their controls during spacecraft buildup and testing during IT at GSFC and at the launch range in Japan. The Safety Inhibit Timeline Tool was a pathfinder approach for reviewing software that controls the electrical inhibits. The Safety Inhibit Timeline Tool strengthens the Safety Analysts understanding of the removal of inhibits during the IT process with safety critical software. With this tool, the Safety Analyst can confirm proper safe configuration of a spacecraft during each IT test, track inhibit and software configuration changes, and assess software criticality. In addition to understanding inhibits and controls during IT, the tool allows the Safety Analyst to better communicate to engineers and management the changes in inhibit states with each phase of hardware and software testing and the impact of safety risks. Lessons learned from participating in the GPM campaign at NASA and JAXA will be discussed during this session.

Inhibits↗
NASA NTRSDate not supplied

Smart Sensor Systems for Human Health and Environmental Applications

Sensors and sensor systems are central to providing improved awareness of an individual's health state and surroundings. This presentation describes efforts to develop Smart Sensor Systems for a range of health and safety applications moving towards distributed intelligence. This includes efforts to develop a human health breath monitoring system using this microsensor Smart Sensor System approach. The same core technology can be used for a range of applications related to improved human health and environmental monitoring. Other examples of human health relevant technology development will also be given.

Smart Sensors Health↗
NASA NTRS1984

Reserve Li/SOC12 Battery Safety Testing

A reserve Lithium/Thionyl Chloride Battery concept is developed and undergoing feasibility testing in terms of performance, safety and abusive conditions. The feasibility of employing a battery of this type to replace thermal batteries in certain applications is demonstrated. Excellent performance of a Li/SOCl2 reserve battery is obtained across the temperature range from 0 C to +44 C. Performance improvement over the thermal battery usage is greater by a factor of 3 when discharge time and energy density are compared. Performance over an expanded temperature range is also possible. Safety and abusive testing is accomplished successfully on a series of five units. Further performance improvements can be achieved with regard to battery weight and volume reductions.

Dils, C. T.↗
NASA NTRS2001

The Advanced Technology Development Center (ATDC)

NASA is building the Advanced Technology Development Center (ATDC) to provide a 'national resource' for the research, development, demonstration, testing, and qualification of Spaceport and Range Technologies. The ATDC will be located at Space Launch Complex 20 (SLC-20) at Cape Canaveral Air Force Station (CCAFS) in Florida. SLC-20 currently provides a processing and launch capability for small-scale rockets; this capability will be augmented with additional ATDC facilities to provide a comprehensive and integrated in situ environment. Examples of Spaceport Technologies that will be supported by ATDC infrastructure include densified cryogenic systems, intelligent automated umbilicals, integrated vehicle health management systems, next-generation safety systems, and advanced range systems. The ATDC can be thought of as a prototype spaceport where industry, government, and academia, in partnership, can work together to improve safety of future space initiatives. The ATDC is being deployed in five separate phases. Major ATDC facilities will include a Liquid Oxygen Area; a Liquid Hydrogen Area, a Liquid Nitrogen Area, and a multipurpose Launch Mount; 'Iron Rocket' Test Demonstrator; a Processing Facility with a Checkout and Control System; and Future Infrastructure Developments. Initial ATDC development will be completed in 2006.

Clements, G. R.↗
NASA NTRS1989

A guide to structural factors for advanced composites used on spacecraft

The use of composite materials in spacecraft systems is constantly increasing. Although the areas of composite design and fabrication are maturing, they remain distinct from the same activities performed using conventional materials and processes. This has led to some confusion regarding the precise meaning of the term 'factor of safety' as it applies to these structures. In addition, composite engineering introduces terms such as 'knock-down factors' to further modify material properties for design purposes. This guide is intended to clarify these terms as well as their use in the design of composite structures for spacecraft. It is particularly intended to be used by the engineering community not involved in the day-to-day composites design process. An attempt is also made to explain the wide range of factors of safety encountered in composite designs as well as their relationship to the 1.4 factor of safety conventionally applied to metallic structures.

Vanwagenen, Robert↗
DOE OSTI2026

Variability of MHD instabilities in benign termination of high-current runaway electron beams in the JET and DIII-D tokamaks

Benign termination, in which magnetohydrodynamic (MHD) instabilities deconfine runaway electrons (REs) following hydrogenic injections, is a promising strategy for mitigating dangerous RE loads after disruptions. Recent experiments on the Joint European Torus (JET) have explored this scenario at higher pre-disruptive plasma currents than are achievable on other devices, revealing challenges in obtaining benign terminations at I p ≥2.5 MA. This work analyzes the evolution of these high-current RE beams and their terminating MHD events using fast magnetic sensor measurements and EFIT equilibrium reconstructions for approximately 40 JET and 20 DIII-D tokamak discharges. On JET, unsuccessful non-benign terminations occur at low edge safety factor (q edge ≈ 2), and are preceded by intermittent, non-terminating MHD events at higher rational qedge. Trends in the internal inductance I i indicate more peaked RE current profiles in the high-I p non-benign population, which may hinder successful recombination through re-ionization of the companion plasma. In contrast, benign terminations on JET typically occur at higher q edge ≥3 and exhibit less peaked RE current profiles. DIII-D displays a broader range of terminating edge safety factors, again correlated with the measured values. Across both tokamaks, the RE current peaking is therefore found to determine which MHD instability boundary is encountered, a result confirmed by linear resistive MHD modeling with the CASTOR3D code. Measured growth rates are similar for benign and non-benign cases, indicating that ideal MHD timescales at low density after hydrogenic injection do not alone explain efficient RE deconfinement. Instead, non-benign cases are most readily characterized by their comparably lower overall MHD perturbation amplitudes δB. These observations suggest that the interplay between ideal and resistive dynamics governs the termination process, with implications for extrapolating benign RE termination to high-I p reactor scenarios.

MHD instabilities↗