Search NASA⌕ Search

SEARCH · Search NASA

Results for “Root Characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effects of turbulence in the atmosphere of Venus on Pioneer Venus radio, phase 2

Two problems related to the effects of turbulence in the atmosphere of Venus on the Pioneer entry probe radio link were studied. In the first problem, the cross correlation between the log amplitude and phase fluctuations of the Pioneer Venus communications link is examined. Data show that for fluctuation frequencies above approximately 1 Hz there is little or no correlation. For frequencies below this region the correlation is weak and the square root of the coherence has a peak value close to 0.65. The second problem consists of interferring turbulence characteristics of the Venus atmosphere from the Mariner 5 phase fluctuations. Data show that with the data processing techniques developed and currently available, the phase error due to oscillator drift, assumed trajectory delay, and spline curve fit exceed the turbulence induced fluctuations. Results show that it is not possible to interfere with the turbulence characteristics from Mariner 5 phase fluctuations.

Woo, R. T.↗
DOE OSTI2023

Performance assessment of a real water source heat pump within a hardware-in-the-loop (HIL) testing environment

Over the last decade, the global fight against climate change through electrification has led to an increase in research on building heating, ventilation, and air conditioning (HVAC) systems that utilize intelligent control algorithms to provide demand-side grid service while also maintaining the thermal comfort of building occupants. As the pivotal point between building electricity consumption and indoor thermal comfort, high-efficiency electrical vapor-compression heat pumps are at the center of these emerging studies, and various grid-interactive and occupant-comfort control algorithms have been developed for them. The impact of these algorithms on heat pump operation and performance when subjected to different weather conditions, building loads, and grid requests calls for investigation and verification via experimental testing with actual heat pumps integrated with real-time building and grid responses. This study introduces a Water-Source Heat Pump (WSHP) Hardware-in-The-Loop (HIL) Test Facility that is the first of its kind. This testbed utilizes a 2-ton variable speed water-to-air heat pump that is capable of interacting with a virtual environment currently comprised of an EnergyPlus (E+) building simulation, an agent-based occupant behavioral model, and a single U-tube ground-loop heat exchanger (GLHE) model. Detailed descriptions of the testbed’s physical design and operation, virtual environment, as well as their mutual communication is provided. An uncertainty analysis is also performed under manufacturer specified heating and cooling design conditions. This analysis shows that the total load across the WSHP’s demand side heat exchanger, i.e., the sum of its latent and sensible components, can be measured with a relative uncertainty of ± 10.4% and ± 3.6% in cooling and heating mode respectively. The WSHP’s coefficient of performance (COP) can be measured with relative uncertainties of ± 10.4% in cooling mode, and ± 3.7% in heating mode. A preliminary 24-h experimental demonstration is then performed utilizing the DOE prototype small commercial office building model in E+. The simulation takes place in Atlanta, GA on the date of 08/26/15 from 12:00 AM to 11:59 PM using TMY3 weather data. Here, the results from this demonstration show that over the course of this experiment the simulated outputs of zone dry-bulb temperature, zone humidity ratio, and WSHP inlet water temperature can be tracked by testbed emulators up to a root mean squared error (RMSE) of ± 0.27 °C, ± 0.376 g/kg, and ± 0.85 °C respectively. The WSHP’s dynamic behavioral characteristics and performance are also captured, and correspond well with the authors’ previous understanding of heat pump efficiency as a function of evaporator and condenser fluid inlet conditions respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1976

Surface photometry of Virgo cluster galaxies - Barred galaxies

Photographic surface photometry in B and V is presented for three barred galaxies in the Virgo cluster: N4548, N4596, and N4608. Intercomparisons of luminosity and color profiles and standard photometric parameters indicate that for these galaxies: (1) the nuclear component follows the fourth-root-of-radius luminosity law for both B and V, (2) the luminosity profiles along the bar show a characteristic shoulder with a slight fall in B-V color profile at the brightest point in the bar, the strength of the effect declining from N4548 to N4608, (3) the integrated bar component is slightly bluer than the nucleus, and (4) as the disk, arm, and ring components contribute less to the total luminosity of the system, the contribution of the bar increases as does the equivalent gradient.

Benedict, G. F.↗
NASA NTRS1984

Issues in Developing a Normative Descriptive Model for Dyadic Decision Making

Most research in modelling human information processing and decision making has been devoted to the case of the single human operator. In the present effort, concepts from the fields of organizational behavior, engineering psychology, team theory and mathematical modelling are merged in an attempt to consider first the case of two cooperating decisionmakers (the Dyad) in a multi-task environment. Rooted in the well-known Dynamic Decision Model (DDM), the normative descriptive approach brings basic cognitive and psychophysical characteristics inherent to human behavior into a team theoretic analytic framework. An experimental paradigm, involving teams in dynamic decision making tasks, is designed to produce the data with which to build the theoretical model.

Serfaty, D.↗
NASA NTRS1959

A Buffet Investigation at High Subsonic Speeds of Wing-Fuselage-Tail Combinations having Sweptback Wings with NACA Four-Digit Thickness Distributions, Fences, and Body Contouring

An investigation has been made to determine the effect of wing fences, fuselage contouring, varying wing sweepback angle from 40 deg. to 45 deg., mounting the horizontal tail on an outboard boom) and wing thickness distribution upon the buffeting response of typical airplane configurations employing sweptback wings of high aspect ratio. The tests were conducted through an angle-of-attack range at Mach numbers varying from 0.60 to 0.92 at a Reynolds number of 2 million. For the combinations with 40 deg. of sweepback, the addition of multiple wing fences usually decreased the buffeting at moderate and high lift coefficients and reduced the erratic variation of buffet intensities with increasing lift coefficient and Mach number. Fuselage contouring also reduced buffeting but was not as effective as the wing fences. At most Mach numbers, buffeting occurred at higher lift coefficients for the combination with the NACA 64A thickness distributions than for the combination with the NACA four-digit thickness distributions. At high subsonic speeds, heavy buffeting was usually indicated at lift coefficients which were lower than the lift coefficients for static-longitudinal instability. The addition of wing fences improved the pitching-moment characteristics but had little effect on the onset of buffeting. For most test conditions and model configurations, the root-mean- square and the maximum values measured for relative buffeting indicated similar effects and trends; however, the maximum buffeting loads were usually two to three times the root-mean-square intensities.

Sutton, Fred B.↗
NASA NTRS2003

Transonic Unsteady Aerodynamics of the F/A-18E at Conditions Promoting Abrupt Wing Stall

A transonic wind tunnel test of an 8% F/A-18E model was conducted in the NASA Langley Research Center (LaRC) 16-Foot Transonic Tunnel (16-Ft TT) to investigate the Abrupt Wing Stall (AWS) characteristics of this aircraft. During this test, both steady and unsteady measurements of balance loads, wing surface pressures, wing root bending moments, and outer wing accelerations were performed. The test was conducted with a wide range of model configurations and test conditions in an attempt to reproduce behavior indicative of the AWS phenomenon experienced on full-scale aircraft during flight tests. This paper focuses on the analysis of the unsteady data acquired during this test. Though the test apparatus was designed to be effectively rigid. model motions due to sting and balance flexibility were observed during the testing, particularly when the model was operating in the AWS flight regime. Correlation between observed aerodynamic frequencies and model structural frequencies are analyzed and presented. Significant shock motion and separated flow is observed as the aircraft pitches through the AWS region. A shock tracking strategy has been formulated to observe this phenomenon. Using this technique, the range of shock motion is readily determined as the aircraft encounters AWS conditions. Spectral analysis of the shock motion shows the frequencies at which the shock oscillates in the AWS region, and probability density function analysis of the shock location shows the propensity of the shock to take on a bi-stable and even tri-stable character in the AWS flight regime.

Schuster, David M.↗
DOE OSTI2025

Pine‐fungal co‐invasion alters whole‐ecosystem properties of a native eucalypt forest

Summary Pine‐fungal co‐invasions into native ecosystems are increasingly prevalent across the southern hemisphere. In Australia, invasive pines slowly spread into native eucalypt forests, creating novel mixed forests. We sought to understand how pine‐fungal co‐invasions impact interconnected above‐ and belowground ecosystem characteristics. We sampled beneath maturePinus radiataandEucalyptus racemosain a pine‐invaded eucalypt forest in New South Wales, Australia. We measured microbial community composition via amplicon sequencing of 16S, ITS2, and 18S rDNA regions, microbial metabolic activity via Biolog plate substrate utilization, and soil, leaf litter, and understory plant characteristics. Pines were associated with decreased topsoil moisture, increased pine litter, and decreased eucalypt litter total phosphorus content. Soils and roots beneath pines had distinct microbial community composition and activity relative to eucalypts, including decreased bacterial diversity, decreased microbial utilization of several C‐ and N‐rich substrates, and enrichment of pine‐associated ectomycorrhizae. Introduced suilloid fungi were abundant across both pine and eucalypt soils and roots. Many ecosystem impacts increased with pine size. Invasive pines and their ectomycorrhizae have significant impacts on eucalypt forest properties as they grow. Interconnected impacts at the scale of individual trees should be considered when managing invaded forests and predicting effects of pine invasions.

Plant Sciences↗
DOE OSTI2023

Classification Algorithm for Dark Matter Search using Skipper-CCD

In this project, I used ROOT framework with C++ for data analysis and Geant4 for simulating different particles’ interaction with the detector to study the characteristic of their tracks. I prepared the tagged dataset for machine learning training both the real experiment data taken in MINOS and simulation data from Geant4.

Chen, Meng-Wei↗
NASA NTRS2013

Enhanced Schapery Theory Software Development for Modeling Failure of Fiber-Reinforced Laminates

Progressive damage and failure analysis (PDFA) tools are needed to predict the nonlinear response of advanced fiber-reinforced composite structures. Predictive tools should incorporate the underlying physics of the damage and failure mechanisms observed in the composite, and should utilize as few input parameters as possible. The purpose of the Enhanced Schapery Theory (EST) was to create a PDFA tool that operates in conjunction with a commercially available finite element (FE) code (Abaqus). The tool captures the physics of the damage and failure mechanisms that result in the nonlinear behavior of the material, and the failure methodology employed yields numerical results that are relatively insensitive to changes in the FE mesh. The EST code is written in Fortran and compiled into a static library that is linked to Abaqus. A Fortran Abaqus UMAT material subroutine is used to facilitate the communication between Abaqus and EST. A clear distinction between damage and failure is imposed. Damage mechanisms result in pre-peak nonlinearity in the stress strain curve. Four internal state variables (ISVs) are utilized to control the damage and failure degradation. All damage is said to result from matrix microdamage, and a single ISV marks the micro-damage evolution as it is used to degrade the transverse and shear moduli of the lamina using a set of experimentally obtainable matrix microdamage functions. Three separate failure ISVs are used to incorporate failure due to fiber breakage, mode I matrix cracking, and mode II matrix cracking. Failure initiation is determined using a failure criterion, and the evolution of these ISVs is controlled by a set of traction-separation laws. The traction separation laws are postulated such that the area under the curves is equal to the fracture toughness of the material associated with the corresponding failure mechanism. A characteristic finite element length is used to transform the traction-separation laws into stress-strain laws. The ISV evolution equations are derived in a thermodynamically consistent manner by invoking the stationary principle on the total work of the system with respect to each ISV. A novel feature is the inclusion of both pre-peak damage and appropriately scaled, post-peak strain softening failure. Also, the characteristic elements used in the failure degradation scheme are calculated using the element nodal coordinates, rather than simply the square root of the area of the element.

Pineda, Evan J.↗
NASA NTRS1960

Aerodynamic Performance and Static Stability at Mach Number 3.3 of an Aircraft Configuration Employing Three Triangular Wing Panels and a Body Equal Length

An aircraft configuration, previously conceived as a means to achieve favorable aerodynamic stability characteristics., high lift-drag ratio, and low heating rates at high supersonic speeds., was modified in an attempt to increase further the lift-drag ratio without adversely affecting the other desirable characteristics. The original configuration consisted of three identical triangular wing panels symmetrically disposed about an ogive-cylinder body equal in length to the root chord of the panels. This configuration was modified by altering the angular disposition of the wing panels, by reducing the area of the panel forming the vertical fin, and by reshaping the body to produce interference lift. Six-component force and moment tests of the modified configuration at combined angles of attack and sideslip were made at a Mach number of 3.3 and a Reynolds number of 5.46 million. A maximum lift-drag ratio of 6.65 (excluding base drag) was measured at a lift coefficient of 0.100 and an angle of attack of 3.60. The lift-drag ratio remained greater than 3 up to lift coefficient of 0.35. Performance estimates, which predicted a maximum lift-drag ratio for the modified configuration 27 percent greater than that of the original configuration, agreed well with experiment. The modified configuration exhibited favorable static stability characteristics within the test range. Longitudinal and directional centers of pressure were slightly aft of the respective centroids of projected plan-form and side area.

James, Carlton S.↗
DOE OSTI2020

Distributed Aerodynamic Control using Active Trailing-Edge Flaps for Large Wind Turbines

This work presents a numerical framework to investigate distributed aerodynamic control devices for application in large wind turbines. Tool capabilities were extended to facilitate multiple aerodynamic polar tables. The airfoil aerodynamics characteristics were automatically determined, and blade-pitch, generator-torque, and trailing-edge-flap controllers were tuned in-the-loop according to a specific blade design. This automated workflow allows analysis and optimization of trailing-edge flaps, enabling codesign studies. Results targeted reductions of root-flap-bending moment derivatives. The applied trailing-edge-flap control reduced the standard deviation of root-flap-bending moments by more than 6% and benefit related parameters, e.g., reduce blade-tip deflections, by up to 8%. Because of varying thrust distributions along the blade span, different flap designs have nonlinear characteristics in terms of the control objective and show best performance when located at the radial position with maximum thrust. In general, larger flaps provide a greater influence to reduce the target control objective.

17 WIND ENERGY↗
NASA NTRS1986

Geophysical characteristics and crustal structure of greenstone terranes: Canadian Shield

Geophysical studies in the Canadian Shield have provided some insights into the tectonic setting of greenstone belts. Greenstone belts are not rooted in deep crustal structures. Geophysical techniques consistently indicate that greenstones are restricted to the uppermost 10 km or so of crust and are underlain by geophysically normal crust. Gravity models suggest that granitic elements are similarly restricted, although magnetic modelling suggests possible downward extension to the intermediate discontinuity around approx. 18 km. Seismic evidence demonstrates that steeply-dipping structure, which can be associated with the belts in the upper crust, is not present in the lower crust. Horizontal intermediate discontinuities mapped under adjacent greenstone and granitic components are not noticeably disrupted in the boundary zone. Geophysical evidence points to the presence of discontinuities between greenhouse-granite and adjacent metasedimentary erranes. Measured stratigraphic thicknesses of greenstone belts are often twice or more the vertical thicknesses determined from gravity modelling. Explantations advanced for the discrepancy include stratigraphy repeated by thrust faulting and/or listric normal faulting, mechanisms which are consistent with certain aspects of conceptual models of greenstone development. Where repetition is not a factor the gravity evidence points to removal of the root zones of greenstone belts. For one region, this has been attributed to magmatic stopping during resurgent caldera activity.

Thomas, M. D.↗
NASA NTRS2011

Geospace Environment Modeling 2008-2009 Challenge: Ground Magnetic Field Perturbations

Acquiring quantitative metrics!based knowledge about the performance of various space physics modeling approaches is central for the space weather community. Quantification of the performance helps the users of the modeling products to better understand the capabilities of the models and to choose the approach that best suits their specific needs. Further, metrics!based analyses are important for addressing the differences between various modeling approaches and for measuring and guiding the progress in the field. In this paper, the metrics!based results of the ground magnetic field perturbation part of the Geospace Environment Modeling 2008 2009 Challenge are reported. Predictions made by 14 different models, including an ensemble model, are compared to geomagnetic observatory recordings from 12 different northern hemispheric locations. Five different metrics are used to quantify the model performances for four storm events. It is shown that the ranking of the models is strongly dependent on the type of metric used to evaluate the model performance. None of the models rank near or at the top systematically for all used metrics. Consequently, one cannot pick the absolute winner : the choice for the best model depends on the characteristics of the signal one is interested in. Model performances vary also from event to event. This is particularly clear for root!mean!square difference and utility metric!based analyses. Further, analyses indicate that for some of the models, increasing the global magnetohydrodynamic model spatial resolution and the inclusion of the ring current dynamics improve the models capability to generate more realistic ground magnetic field fluctuations.

Pulkkinen, A.↗
NASA NTRS2017

The Use of Sun Elevation Angle for Stereogrammetric Boreal Forest Height in Open Canopies

Stereogrammetry applied to globally available high resolution spaceborne imagery (HRSI; less than 5 m spatial resolution) yields fine-scaled digital surface models (DSMs) of elevation. These DSMs may represent elevations that range from the ground to the vegetation canopy surface, are produced from stereoscopic image pairs (stereo pairs) that have a variety of acquisition characteristics, and have been coupled with lidar data of forest structure and ground surface elevation to examine forest height. This work explores surface elevations from HRSI DSMs derived from two types of acquisitions in open canopy forests. We (1) apply an automated mass-production stereogrammetry workflow to along-track HRSI stereo pairs, (2) identify multiple spatially coincident DSMs whose stereo pairs were acquired under different solar geometry, (3) vertically co-register these DSMs using coincident spaceborne lidar footprints (from ICESat-GLAS) as reference, and(4) examine differences in surface elevations between the reference lidar and the co-registered HRSI DSMs associated with two general types of acquisitions (DSM types) from different sun elevation angles. We find that these DSM types, distinguished by sun elevation angle at the time of stereo pair acquisition, are associated with different surface elevations estimated from automated stereogrammetry in open canopy forests. For DSM values with corresponding reference ground surface elevation from spaceborne lidar footprints in open canopy northern Siberian Larix forests with slopes less than10, our results show that HRSI DSM acquired with sun elevation angles greater than 35deg and less than 25deg (during snow-free conditions) produced characteristic and consistently distinct distributions of elevation differences from reference lidar. The former include DSMs of near-ground surfaces with root mean square errors less than 0.68 m relative to lidar. The latter, particularly those with angles less than 10deg, show distributions with larger differences from lidar that are associated with open canopy forests whose vegetation surface elevations are captured. Terrain aspect did not have a strong effect on the distribution of vegetation surfaces. Using the two DSM types together, the distribution of DSM-differenced heights in forests (6.0 m, sigma = 1.4 m) was consistent with the distribution of plot-level mean tree heights (6.5m, sigma = 1.2 m). We conclude that the variation in sun elevation angle at time of stereo pair acquisition can create illumination conditions conducive for capturing elevations of surfaces either near the ground or associated with vegetation canopy. Knowledge of HRSI acquisition solar geometry and snow cover can be used to understand and combine stereogrammetric surface elevation estimates to co-register rand difference overlapping DSMs, providing a means to map forest height at fine scales, resolving the vertical structure of groups of trees from spaceborne platforms in open canopy forests.

Paul M Montesano↗
NASA NTRS1976

Optimum design considerations of a gust alleviator for aircraft

A gust alleviation system for aircraft flying in turbulent air was analyzed. A vane sensor (with noise) was used to measure vertical gusts, and elevators and flaps were used to reduce the root-mean-square value of the normal accelerations associated with the aircraft response to gusts. Since turbulence has stochastic properties, stochastic control theory was used in the analysis. A quadratic performance-index function involving normal acceleration and control deflections was minimized. Application of the analysis was illustrated by a short take-off and landing (STOL) airplane in flight through turbulent air. Effects of varying the noise characteristics of the vane sensor and of a weighting matrix in the performance-index function were determined. Calculations were performed as required by stochastic control theory to obtain the root-mean-square response of the airplane to turbulence. Results show that good alleviation was calculated when the intensity of the measurement noise was about 3.6 percent of the vane deflection angles.

Oehman, W. I.↗
NASA NTRS2023

Development of High-Resolution Soil Hydraulic Parameters with Use of Earth Observations for Enhancing Root Zone Soil Moisture Product

Regional quantification of energy and water balance fluxes depends inevitably on the estimation of surface and rootzone soil moisture. The simulation of soil moisture depends on the soil retention characteristics, which are difficult to estimate at a regional scale. Thus, the present study proposes a new method to estimate high-resolution Soil Hydraulic Parameters (SHPs) which in turn help to provide high-resolution (spatial and temporal) rootzone soil moisture (RZSM) products. The study is divided into three phases—(I) involves the estimation of finer surface soil moisture (1 km) from the coarse resolution satellite soil moisture. The algorithm utilizes MODIS 1 km Land Surface Temperature (LST) and 1 km Normalized difference vegetation Index (NDVI) for downscaling 25 km C-band derived soil moisture from AMSR-2 to 1 km surface soil moisture product. At one of the test sites, soil moisture is continuously monitored at 5, 20, and 50 cm depth, while at 44 test sites data were collected randomly for validation. The temporal and spatial correlation for the downscaled product was 70% and 83%, respectively. (II) In the second phase, downscaled soil moisture product is utilized to inversely estimate the SHPs for the van Genuchten model (1980) at 1 km resolution. The numerical experiments were conducted to understand the impact of homogeneous SHPs as compared to the three-layered parameterization of the soil profile. It was seen that the SHPs estimated using the downscaled soil moisture (I-d experiment) performed with similar efficiency as compared to SHPs estimated from the in-situ soil moisture data (I-b experiment) in simulating the soil moisture. The normalized root mean square error (nRMSE) for the two treatments was 0.37 and 0.34, respectively. It was also noted that nRMSE for the treatment with the utilization of default SHPs (I-a) and AMSR-2 soil moisture (I-c) were found to be 0.50 and 0.43, respectively. (III) Finally, the derived SHPs were used to simulate both surface soil moisture and RZSM. The final product, RZSM which is the daily 1 km product also showed a nearly 80% correlation at the test site. The estimated SHPs are seen to improve the mean NSE from 0.10 (I-a experiment) to 0.50 (I-d experiment) for the surface soil moisture simulation. The mean nRMSE for the same was found to improve from 0.50 to 0.31.

soil moisture downscaling↗
NASA NTRS1990

An experimental study of tip shape effects on the flutter of aft-swept, flat-plate wings

The effects of tip chord orientation on wing flutter are investigated experimentally using six cantilever-mounted, flat-plate wing models. Experimentally determined flutter characteristics of the six models are presented covering both the subsonic and transonic Mach number ranges. While all models have a 60 degree leading edge sweep, a 40.97 degree trailing edge sweep, and a root chord of 34.75 inches, they are subdivided into two series characterized by a higher aspect ratio and a lower aspect ratio. Each series is made up of three models with tip chord orientations which are parallel to the free-stream flow, perpendicular to the model mid-chord line, and perpendicular to the free-stream flow. Although planform characteristics within each series of models are held constant, structural characteristics such as mode shapes and natural frequencies are allowed to vary.

Dansberry, Bryan E.↗