Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLIPSTREAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

Full-Scale Tests of 4- and 6-Blade, Single- and Dual-Rotating Propellers, Special Report

Test of 10-foot diameter, 4- and 6-blade single- and dual-rotating propellers were conducted in the 20-foot propeller-research tunnel. The propellers were mounted at the front end of a streamline body incorporating spinners to house the hub portions. The effect of a symmetrical wing mounted in the slipstream was investigated. The blade angles investigated ranged from 20 degrees to 65 degrees; the latter setting corresponds to airplane speeds of over 500 miles per hour. The results indicate that dual-rotating propellers were from 0 to 6% more efficient than single-rotating ones; but when operating in the presence of a wing the gain was reduced about one-half. Other advantages of dual-rotating propellers were found to include greater power absorption and greater efficiency at the low V/nD operating range of high pitch propellers.

Biermann, David↗
NASA NTRS1939

Preliminary Model Tests of a Wing-Duct Cooling System for Radial Engines, Special Report

Wind-tunnel tests were conducted on a model wing-nacelle combination to determine the practicability of cooling radial engines by forcing the cooling air into wing-duct entrances located in the propeller slipstream, passing the air through the engine baffles from rear to front, and ejecting the air through an annular slot near the front of the nacelle. The tests, which were of a preliminary nature, were made on a 5-foot-chord wing and a 20-inch-diameter nacelle. A 3-blade, 4-foot-diameter propeller was used. The tests indicated that this method of cooling and cowling radial engines is entirely practicable providing the wing of the prospective airplane is sufficiently thick to accommodate efficient entrance ducts , The drag of the cowlings tested was definitely less than for the conventional N.A.C.A. cowling, and the pressure available at low air speed corresponding to operation on the ground and at low flying speeds was apparently sufficient for cooling most present-day radial engines.

Biermann, David↗
NASA NTRS1939

Preliminary Tests of Blowers of Three Designs Operating in Conjunction with a Wing-Duct Cooling System for Radial Engines, Special Report

This paper is one of several dealing with methods intended to reduce the drag of present-day radial engine installations and improve the cooling at zero and low air speeds, The present paper describes model wind-tunnel tests of blowers of three designs tested in conjunction with a wing-nacelle combination. The principle of operation involved consists of drawing cooling air into ducts located in the wing root at the point of maximum slipstream velocity, passing the air through the engine baffles from rear to front, and exhausting the air through an annular slot located between the propeller and the engine with the aid of a blower mounted on the spinner. The test apparatus consisted essentially of a stub wing having a 5-foot chord and a 15-foot span, an engine nacelle of 20 inches diameter enclosing a 25-horsepower electric motor, and three blowers mounted on propeller spinners. Two of the blowers utilize centrifugal force while the other uses the lift from airfoils to force the air out radially through the exit slot. Maximum efficiencies of over 70 percent were obtained for the system as a whole. Pressures were measured over the entire flight range which were in excess of those necessary to cool present-day engines, The results indicated that blowers mounted on propeller spinners could be built sufficiently powerful and efficient to warrant their use as the only, or chief, means of forcing air through the cooling system, so that cooling would be independent of the speed of the airplane.

Biermann, David↗
NASA NTRS1942

Preliminary Wind-Tunnel Tests of the Effect of Nacelles on the Characteristics of a Twin-Engine Bomber Model with Low-Drag Wing, Special Report

Tests were made in the NACA 19-foot pressure tunnel of a simplified twin-engine bomber model with an NACA low-drag wing primarily to obtain an indication of the effects of engine nacelles on the characteristics of the model both with and without simple split trailing-edge flaps. Nacelles with conventional-type cowlings representative of those used on an existing high-performance airplane and with NACA high-speed type E cowlings were tested. The tests were made without propeller slipstream. The aerodynamic effects of adding the nacelles to the low-drag wing were similar to the effects commonly obtained by adding similar nacelles to conventional wings. The maximum lift coefficient without flaps was slightly increased, but the increment in maximum lift due to deflecting the flaps was somewhat decreased. The stalling characteristics were improved by the presence of the nacelles. Addition of the nacelles had a destabilizing effect on the pitching moments, as is usual for nacelles that project forward of the wing. The drag increments due to the nacelles were of the usual order of magnitude, with the increment due to the nacelles with NACA type E cowlings approximately one-third less than that of the nacelles with conventional cowlings with built-in air scoops.

Wenzinger, Carl J.↗
NASA NTRS1953

Low-Speed Longitudinal Stability Characteristics of a 1/6-Scale Model of the Republic XF-84H Airplane with the Propeller Operating

A low-speed investigation was made of a 1/6-scale model of the Republic XF-84H airplane. The model had a single tractor propeller and a 40deg swept wing of aspect ratio 3.45. This investigation was undertaken to provide information on the effects of propeller operation on longitudinal stability characteristics for the XF -84H airplane and to provide an indication of slipstream effects that might be encountered on similar swept-wing configurations. Effects of propeller operation were generally destabilizing for all conditions investigated; however, the over-all stability characteristics with power on were greatly dependent on the power-off characteristics. With flaps and slats retracted, longitudinal instability was present at moderate angles of attack both with the propeller off and with power on. The longitudinal stability with flaps and slats deflected, which was satisfactory without power, was decreased by propeller operation, but no marked pitch-up tendency was indicated. Significant improvement in the power-on stability with flaps retracted was achieved by use of either a wing fence at 75 percent semispan, a leading-edge chord-extension from 65 to 94 percent semispan, or a raised horizontal tail located 65 percent semispan above the thrust line.

Sleeman, William C.↗
NASA NTRS1947

Altitude-Wind-Tunnel Investigation of R-4360-18 Power-Plant Installation for XR60 Airplane: Performance of Induction and Exhaust Systems - 3

A study has been made of the performance of the induction and the exhaust systems on the XR60 power-plant installation as part of an investigation conducted in the Cleveland altitude wind tunnel. Altitude flight conditions from 5000 to 30,000 feet were simulated for a range of engine powers from 750 to 3000 brake horsepower. Slipstream rotation prevented normal pressure recoveries in the right side of the main duct in the region of the right intercooler cooling-air duct inlet. Total-pressure losses in the charge-air flow between the turbosupercharger and the intercoolers were as high as 2.1 inches of mercury. The total-pressure distribution of the charge air at the intercooler inlets was irregular and varied as much as 1.0 inch of mercury from the average value at extreme conditions, Total-pressure surveys at the carburetor top deck showed a variation from the average value of 0.3 inch of mercury at take-off power and 0.05 inch of mercury at maximum cruising power, The carburetor preheater system increased the temperature of the engine charge air a maximum of about 82 F at an average cowl-inlet air temperature of 9 F, a pressure altitude of 5000 feet, and a brake horsepower of 1240.

Dupree, David T.↗
NASA NTRS2014

Tradespace Exploration of Distributed Propulsors for Advanced On-Demand Mobility Concepts

Combustion-based sources of shaft power tend to significantly penalize distributed propulsion concepts, but electric motors represent an opportunity to advance the use of integrated distributed propulsion on an aircraft. This enables use of propellers in nontraditional, non-thrust-centric applications, including wing lift augmentation, through propeller slipstream acceleration from distributed leading edge propellers, as well as wingtip cruise propulsors. Developing propellers for these applications challenges long-held constraints within propeller design, such as the notion of optimizing for maximum propulsive efficiency, or the use of constant-speed propellers for high-performance aircraft. This paper explores the design space of fixed-pitch propellers for use as (1) lift augmentation when distributed about a wing's leading edge, and (2) as fixed-pitch cruise propellers with significant thrust at reduced tip speeds for takeoff. A methodology is developed for evaluating the high-level trades for these types of propellers and is applied to the exploration of a NASA Distributed Electric Propulsion concept. The results show that the leading edge propellers have very high solidity and pitch well outside of the empirical database, and that the cruise propellers can be operated over a wide RPM range to ensure that thrust can still be produced at takeoff without the need for a pitch change mechanism. To minimize noise exposure to observers on the ground, both the leading edge and cruise propellers are designed for low tip-speed operation during takeoff, climb, and approach.

Borer, Nicholas K.↗
NASA NTRS2016

High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator

Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

Patterson, Michael D.↗
NASA NTRS2016

Cooling of Electric Motors Used for Propulsion on SCEPTOR

Benefits of Electric Power: Reduced energy consumption, Lower emissions, Less noise. Traction motors: Permanent magnet, Synchronous, High torque at low rotational speeds, High power density, (High concentration of heat). Annular inlet: Very compatible with PM motors, (Provides cooling where needed, No need for complicated ducting, Leads to a larger motor diameter which is beneficial for motor torque) Effect of prop wash on heat transfer coefficients: Assumed propeller induced turbulence would increase heat transfer coefficients, Holmes, Obara Yip reported 'propeller slipstream showed little if any apparent effect of the slip stream', Derlaga @ LaRC also found little change in heat transfer in the wake of the propeller.

Aircraft↗
NASA NTRS2019

Evaluation of a Commercial Surface Vorticity Flow Solver for the Modeling of Propeller-Wing Interaction

A commercially available surface vorticity flow solver’s ability to model propeller-wing interaction effects was evaluated. First, a study was conducted to determine solution sensitivity to simulation parameters. Then, a deflected slipstream experiment was replicated with an actuator disk and wing model. Comparison with experimental data showed that predictions of lift and longitudinal force coefficients matched well at low flap deflections, but experienced offsets in magnitude with increasing flap deflection. Predictions of pitching moment differed significantly from experimental data largely due to the simple actuator disk model being insufficient for capturing the effects of non-zero flow incidence and non-uniform inflow.

Fei, Xiaofan↗
NASA NTRS2019

Baseline Assumptions and Future Research Areas for Urban Air Mobility Vehicles

NASA is developing Urban Air Mobility (UAM) concepts to (1) create first-generation reference vehicles that can be used for technology, system, and market studies, and (2) hypothesize second-generation UAM aircraft to determine high-payoff technology targets and future research areas that reach far beyond initial UAM vehicle capabilities. This report discusses the vehicle-level technology assumptions for NASA’s UAM reference vehicles, and highlights future research areas for second-generation UAM aircraft that includes deflected slipstream concepts, low-noise rotors for edgewise flight, stacked rotors/propellers, ducted propellers, solid oxide fuel cells with liquefied natural gas, and improved turbo shaft and reciprocating engine technology. The report also highlights a transportation network-scale model that is being developed to understand the impact of these and other technologies on future UAM solutions.

Antcliff, Kevin↗
NASA NTRS2020

Investigation of a Tandem Tilt-wing VTOL Aircraft in the NASA Langley 12-Foot Low-Speed Tunnel

The emerging Urban Air Mobility market imposes new design requirements on aircraft, including the ability to have vertical take-off and landing (VTOL) capabilities with the ability to transition into fast and efficient forward flight. Industry has proposed many different vehicle configurations, which have many different challenges. A primary challenge facing many of these concepts is flight through the transition corridor from vertical to horizontal flight and back. In an effort to better understand and help improve vehicle safety in the complex transition corridors, NASA Langley Research Center has proposed to characterize the transition corridor with wind tunnel and flight tests for a variety of unmanned aircraft system sized VTOL configurations. The first vehicle of this series is the Langley Aerodrome 8 (LA-8). LA-8 is a high-risk/high-reward tandem tilt-wing vehicle with distributed electric propulsion and a partially deflected slipstream aircraft. The LA-8 vehicle has gone through a preliminary wind tunnel test in NASA Langley's 12-Foot Low-Speed Wind Tunnel. The results of the aerodynamic data collected, including the longitudinal, lateral, and directional force and moment aerodynamic coefficients, from these tests during different phases of flight are presented.

VTOL↗
NASA NTRSDate not supplied

Aerodynamic and Acoustic Interactions Associated with Inboard Propeller-Wing Configurations

A series of aerodynamic performance and acoustic measurements have been made on a range of inboard propeller-wing interaction configurations in the NASA Langley Low Speed Aeroacoustic Wind Tunnel (LSAWT). The results presented in this paper are part of a more expansive testing campaign encompassing both single propeller-wing and multipropeller-wing interactions, the former of which is discussed in the present work. The primary testing parameters of interest to this study are the axial and vertical positioning of the wing relative to the propeller slipstream under a constant propeller advance ratio. A multi-faceted computational effort was also employed in an effort to identify reflection and scattering effects imposed by both the wing geometry as well as the primary components of the facility test setup. This effort consisted of aerodynamic predictions using high-fidelity computational fluid dynamics (CFD), acoustic predictions using an impermeable Ffowcs Williams and Hawkings (FW-H) solver, and acoustic scattering predictions. Acoustic measurements reveal variations in the acoustic directivity behavior of the propeller blade passage frequency for even modest variations in wing position. CFD-based acoustic predictions reveal discrepancies relative to the experimental data, which is believed to be due to complex acoustic scattering behavior within the test section. Initial attempts at modeling the scattered acoustic field showed functional dependency of the acoustic amplitude variations on the wing position relative to the propeller disk, however discrepancies with experimental data remain.

Nikolas S. Zawodny↗
NASA NTRS2021

Sky-Scanning Sun-Tracking Airborne Radiometer (3STAR): Instrument Design, Flight Testing, and Tracking Performance

The Sky-Scanning, Sun-Tracking Airborne Radiometer (3STAR) adapts commercial radiometer technology developed for the ocean color research community to airborne measurement of spectrally resolved solar irradiance and sky radiance. These atmospheric observations are used to derive aerosol optical depth (AOD), supporting localized AOD inputs for atmospheric correction of satellite and airborne data over terrestrial and aquatic (including optically dark) targets. The ability to regionally “tune” atmospheric correction schemes with relevant spatial AOD supports constraining atmospheric correction of remote sensing reflectance. Very wide dynamic range has been achieved for multi-channel band-pass-filter-radiometers originally designed for deployment into the water column. By actively tracking and directly pointing to the Sun, the light attenuation by aerosol particles in the atmospheric column can be quantified. These measurements improve knowledge of atmospheric constituents and the atmospheric corrections required to improve remote sensing capabilities for interpreting reflectance measurements from the Earth surface. 3STAR incorporates a custom Sun-tracking/sky-scanning pointing head, a Sun-tracking camera, and a commercially available, cylindrical, 19-channel radiometer tube assembly. An accurate and responsive mount and tracking system has been developed and certified to NASA and Naval Air Systems Command (NAVAIR) airworthiness standards for deployment into the aircraft slipstream. Ground and flight testing indicate typical tracking errors of less than 0.1 degrees, well within the field of view of the radiometer as required to minimize measurement uncertainty from alignment error. Preliminary AOD measurements compare to within 0.013 with 15 measurements from an Aerosol Robotic Network (AERONET) Cimel instrument at 500 nm wavelength and low solar angle.

Atmosphere↗
NASA NTRSDate not supplied

Tiltwing Transition Flight Analysis Using High-Fidelity CFD

Transition from hover to forward flight and vice versa represents the most critical flight phase of tiltwing aircraft. Despite its importance to ensure a safe operation, the aerodynamics of this maneuver are not sufficiently understood. This paper focuses on the study of transition flight for NASA’s six-passenger tiltwing air taxi by means of high-fidelity computational fluid dynamics simulations. On the basis of a static trim solution, four points within the transition corridor are analyzed: transition mode at wing tilt angles of60and44, and airplane mode at airspeeds of110 ktand155 kt. We investigate the balance of forces and moments for rotor-borne and wing-borne regimes, and how rotor-on-rotor and rotor-on-wing interactions affect performance. The simulations indicate that during the early stages of transition, the vortices remain in close proximity to the proprotors, inducing large fluctuations on the order of the mean blade loading. Additionally, the blowing and swirling effects of the proprotor wakes delay flow separation over a portion of the wing. The mid-transition conditions appear to be critical, with extensive regions of separated flow over the wing. In airplane mode, proprotor-wing slipstream effects can be exploited to enhance lift generation. The results of this paper contribute to a deeper understanding of the complex aerodynamic interactions during transition flight to enable a safer and more efficient operation of tiltwing aircraft.

ARMD↗
DOE OSTI2024

Smart Building Technology Training Modules for Academic and Professional Education

Smart building technologies are a new suite of resources that improve building energy efficiency and resilience, reduce carbon emissions, and provide load flexibility to the grid. However, in both college curricula and building professionals’ continuing education, there is a lack of systematic instruction on smart building technologies–topics that include smart building concepts, key components, smart building controls, “Internet of Things” (IoT) devices, and how to integrate multiple energy systems including distributed energy resources (DER). This major gap in smart building education prevents stakeholders from understanding and adopting smart building technologies in building design and operations. Slipstream leads a DOE-funded project developing a semester-long smart building curriculum for college students and adapting the contents into 16 training videos for building professionals and the general public. The education and training cover the drivers and benefits of smart building technologies, key building energy systems, the latest sensor technologies and IoT devices, and focus on topics related to smart building controls (i.e., energy management information systems, smart building control platforms, cybersecurity, grid-interactive-efficient buildings (GEBs), smart building control methods, and occupant-centric control. This paper describes the project approach, provides outlines of the training materials, and identifies lessons learned in creating the content. We also suggest ways to scale the instruction of smart building concepts to empower the workforce to accelerate the adoption of smart building technologies in the real world.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Developing Smart Building Technology Modules to Enhance Workforce Preparedness: A Case for AI-Driven Academic and Professional Education

Smart building technologies are resources that improve building energy efficiency and resilience, reduce carbon emissions, and provide load flexibility to the grid. However, in both academic curricula and building professionals’ continuing education, there is a lack of systematic instruction on methods to integrate multiple energy systems including distributed energy resources (DER), smart building technologies, AI (Artificial Intelligence) tools and key concepts, components, and controls, including “Internet of Things” (IoT) devices. In today’s dynamic workforce, this major gap in smart building technology education prevents stakeholders from being able to attract talent with an understanding and preparation to adopt smart building technologies in building design and operations. A federally funded project included a partnership between Slipstream and Texas A&M University (TAMU) to develop a semester-long smart building curriculum for engineering college students with the ability to adapt the contents for workforce development of professionals in building services. The final product consists of 16 training videos adapted for building professionals and the public. The educational content and training materials cover the benefits of building energy systems, the latest sensor technologies and IoT devices, all with a focus on smart building technologies. The key drivers are on topics related to smart building controls (i.e., energy management information systems), smart building control platforms, cybersecurity, grid-interactive-efficient buildings (GEBs), smart building control methods, and occupant-centric control. Although not explicitly included the technologies nod to the need for AI driven technologies to prepare engineers and industry professionals to be future ready. This paper describes the project approach, provides outlines of the training materials, and identifies lessons learned in creating the content for this course. The authors suggest ways to scale the instruction of smart building concepts to empower the workforce to accelerate the adoption of smart building technologies and AI-based teaching and learning in higher education and building sector.

99 GENERAL AND MISCELLANEOUS↗