Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Longitudinal and Lateral Stability and Control Characteristics and Vertical-Tail-Load Measurements for a 0.03-Scale Model of the Avro CF-105 Airplane at Mach Numbers of 1.60, 1.80, and 2.00

An investigation has been made in the Langley Unitary Plan wind tunnel at Mach numbers of 1.60, 1.80, and 2.00 to determine the aerodynamic characteristics of a 0.03-scale model of the Avro CF-105 airplane. The investigation included the determination of the static longitudinal and lateral stability, the control and the hinge-moment characteristics of the elevator, rudder, and aileron, as well as the vertical-tail-load characteristics. Although the data are presented without analysis, a limited inspection of the longitudinal control results indicates a loss in maximum lift-drag ratio due to trimming of about 1.8 because of the large static margin. A reduction in static margin would be expected to improve the trim lift-drag ratio but would also reduce the directional stability. With the existing static margin, the configuration is directionally unstable at angles of attack above about 6 deg or 8 deg.

Silvers, H. Norman↗
NASA NTRS1975

Transonic wind-tunnel tests of an F-8 airplane model equipped with 12 and 14-percent thick oblique wings

An experimental investigation was conducted in the Ames 14-foot transonic wind tunnel to study the aerodynamic performance and stability characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing. Two elliptical planform (axis ratio = 8:1) wings, each having a maximum thickness of 12 and 14 percent, were tested. Longitudinal stability data were obtained with no wing and with each of the two wings set at sweep angles of 0, 45, and 60 deg. Lateral directional stability data were obtained for the 12 percent wing only. Test Mach numbers ranged from 0.6 to 1.2 in the unit Reynolds number range from 11.2 to 13.1 million per meter. Angles of attack were between -6 and 22 deg at zero sideslip. Angles of sideslip were between -6 and +6 deg for two angles of attack, depending upon the wing configuration.

Smith, R. C.↗
NASA NTRS1947

Stability and control characteristics of an airplane model having a 45.1 degree swept-back wing with aspect ratio 2.50 and taper ratio 0.42 and a 42.8 degree swept-back horizontal tail with aspect ratio 3.87 and taper ratio 0.49

Tests were made of an airplane model having a 45.1 degree swept-back wing with aspect ratio 2.50 and taper ratio 0.42 and a 42.8 degree swept-back horizontal tail with aspect ratio 3.87 and taper ratio 0.49 to determine its low-speed stability and control characteristics. The test Reynolds number was 2.87 x 10(6) based on a mean aerodynamic chord of 2.47 feet except for some of the aileron tests which were made at a Reynolds number of 2.05 x 10(6). With the horizontal tail located near the fuselage juncture on the vertical tail, model results indicated static longitudinal instability above a lift coefficient that was 0.15 below the lift coefficient at which stall occurred. Static longitudinal stability, however, was manifested throughout the life range with the horizontal tail located near the top of the vertical tail. The use of 10 degrees negative dihedral on the wing had little effect on the static longitudinal stability characteristics. Preliminary tests of the complete model revealed an undesirable flat spot in the yawing-moment curves at low angles of attack, the directional stability being neutral for yaw angles of plus-or-minus 2 degrees. This undesirable characteristic was improved by replacing the thick original vertical tail with a thin vertical tail and by flattening the top of the dorsal fairing.

Schuldenfrei, Marvin↗
NASA NTRS1988

F-15 SMTD low speed jet effects wind tunnel test results

Key results from low speed wind tunnel testing of the F-15 STOL and Maneuver Technology Demonstrator (SMDT) with thrust reversers are presented. Longitudinally, the largest induced increments in the stability and control occur at landing gear height. These generally reflect an induced lift loss and a nose-up pitching moment, and vary with sideslip. Directional stability is reduced at landing gear height with full reverse thrust. Nonlinearities in the horizontal tail effectiveness are found in free air and at landing gear height.

Blake, William B.↗
NASA NTRS1947

Investigation of the Stability and Control Characteristics of a 1/20-Scale Model of the Consolidated Vultee XB-53 Airplane with a Full-Span Leading-Edge Slat in the Langley Free-Flight Tunnel

An investigation of the low-speed; power-off stability and control characteristics of a 1/20-scale model of the Consolidated Vultee XB-53 airplane equipped with full-span leading-edge slats has been conducted in the Langley free-flight tunnel. In this investigation it was found that the-full-span leading-edge slat gave about the same maximum lift coefficient as was obtained with the outboard single slotted flap and inboard slat. The stability and control characteristics were greatly improved except near the stall where the characteristics with the full-span slat were considered unsatisfactory because of a loss of directional stability and a slight nosing-up tendency.

Bennett, Charles V.↗
NASA NTRS1976

Aerodynamic characteristics of a 1/6-scale model of the rotor systems research aircraft with the rotors removed

A wind-tunnel investigation was conducted to refine the aerodynamic characteristics of the rotor systems research aircraft. For the investigation, a 1/6-scale model without a main rotor or a tail rotor was used. The model provided the capability for testing different engine nacelle sizes, engine pylon fairings, and tail configurations. The engine thrust effects were modeled by small engine simulators (fans). Data were obtained primarily over an angle-of-attack range from -13 deg to 13 deg at several values of sideslip. Stability characteristics and control effectiveness were investigated. The model with the scaled engine nacelles and the combination T-tail and lower horizontal tail displayed longitudinal and lateral-directional stability. Results show that by reducing the horizontal or vertical-tail span the longitudinal stability is decreased. Reducing the engine nacelle size increases the static stability of the model. Effective dihedral is essentially zero at 0 deg angle of attack and 0 deg wing incidence.

Mineck, R. E.↗
NASA NTRS1943

Wind-Tunnel Tests of the 1/9-Scale Model of the Curtiss XP-62 Airplane with Various Vertical Tail Arrangements

The effect of various vertical tail arrangements upon the stability and control characteristics of an XP-62 fighter model was investigated. Rudder-free yaw characteristics with take-off power and flaps deflected were satisfactory after dorsal fin modifications. Directional stability was obtained with all modified vertical tails. Satisfactory rudder effectiveness resulted partly because the dual-rotation propellers produced no asymmetric yawing moments. Pedal forces in sideslips were undesirably large but may be easily reduced.

Wallace, Arthur R.↗
NASA NTRS1947

Investigation of the Stability and Control Characteristics of a 1/20-Scale Model of the Consolidated Vultee XB-53 Airplane in the Langley Free-Flight Tunnel

An investigation of the low-speed, power-off stability and control characteristics of a 1/20-scale model of the Consolidated Vultee XB-53 airplane has been conducted in the Langley free-flight tunnel. In the investigation it was found that with flaps neutral satisfactory flight behavior at low speeds was obtainable with an increase in height of the vertical tail and with the inboard slats opened. In the flap-down slat-open condition the longitudinal stability was satisfactory, but it was impossible to obtain satisfactory lateral-flight characteristics even with the increase in height of the vertical tail because of the negative effective dihedral, low directional stability, and large-adverse yawing moments of the ailerons.

Bennett, Charles V.↗
NASA NTRS1975

Aerodynamic characteristics of a hypersonic research airplane concept having a 70 degree swept double delta wing at Mach numbers from 1.50 to 2.86

An experimental investigation of the static longitudinal, lateral, and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing was conducted in the Langley unitary plan wind tunnel. The configuration variables included wing planform, tip fins, center fin, and scramjet engine modules. The investigation was conducted at Mach numbers from 1.50 to 2.86 and at a constant Reynolds number, based on fuselage length, of 3,330,000. Tests were conducted through an angle-of-attack range from about -4 deg to 24 deg with angles of sideslip of 0 deg and 3 deg and at elevon deflections of 0, -10, and -20 deg. The complete configuration was trimmable up to angles of attack of about 22 deg with the exception of regions at low angles of attack where positive elevon deflections should provide trim capability. The angle-of-attack range for which static longitudinal stability also exists was reduced at the higher Mach numbers due to the tendency of the complete configuration to pitch up at the higher angles of attack. The complete configuration was statically stable directionally up to trimmed angles of attack of at least 20 deg for all Mach numbers M with the exception of a region near 4 deg at M = 2.86 and exhibited positive effective dihedral at all positive trimmed angles of attack.

Penland, J. A.↗
NASA NTRS1984

Investigation of the effect of vehicle, angle-of-attack, and trim elevon position on lateral-directional aerodynamic parameters of the Shuttle Orbiter

This paper discusses the lateral-directional stability and control coefficients extracted from onboard measurements made during reentry of flights two to eight of the Space Shuttle Orbiters. Maximum likelihood estimation is applied to data derived from accelerometer and rate gyro measurements and trajectory, meteorological and control surface data to estimate these lateral-directional parameters. Comparison of estimated coefficients across the seven flights and two shuttle vehicles is made. The effect of the angle-of-attack, and trim elevon deflection on estimated values of the stability and control derivatives is also studied.

Schiess, J. R.↗
NASA NTRS1959

Subsonic Aerodynamic Characteristics of an Airplane Configuration with a 63 deg Sweptback Wing and Twin-Boom Tails

A wind-tunnel investigation has been conducted to determine the effects of an unconventional tail arrangement on the subsonic static longitudinal and lateral stability characteristics of a model having a 63 deg sweptback wing of aspect ratio 3.5 and a fuselage. Tail booms, extending rearward from approximately the midsemispan of each wing panel, supported independent tail assemblies well outboard of the usual position at the rear of the fuselage. The horizontal-tail surfaces had the leading edge swept back 45 deg and an aspect ratio of 2.4. The vertical tail surfaces were geometrically similar to one panel of the horizontal tail. For comparative purposes, the wing-body combination was also tested with conventional fuselage-mounted tail surfaces. The wind-tunnel tests were conducted at Mach numbers from 0.25 to 0.95 with a Reynolds number of 2,000,000, at a Mach number of 0.46 with a Reynolds number of 3,500,000, and at a Mach number of 0.20 with a Reynolds number of 7,000,000. The results of the investigation indicate that longitudinal stability existed to considerably higher lift coefficients for the outboard tail configuration than for the configuration with conventional tail. Wing fences were necessary with both configurations for the elimination of sudden changes in longitudinal stability at lift coefficients between 0.3 and 0.5. Sideslip angles up to 15 deg had only small effects upon the pitching-moment characteristics of the outboard tail configuration. There was an increase in the directional stability for the outboard tail configuration at the higher angles of attack as opposed to a decrease for the conventional tail configuration at most of the Mach numbers and Reynolds numbers of this investigation. The dihedral effect increased rapidly with increasing angle of attack for both the outboard and the conventional tail configurations but the increase was greater for the outboard tail configuration. The data indicate that the outboard tail is an effective roll control.

Savage, Howard F.↗
NASA NTRS1981

Effects of wingtip modifications on handling qualities of agricultural aircraft

The effect of wingtip modifications on the stability and control characteristics of an agricultural airplane has been studied by means of a nonplanar quasi-vortex-lattice method. The method is used to compute the changes in steady state and perturbed state lateral-directional stability and control derivatives produced by wingtip mounted winglets, vortex diffuser vanes, and tip extensions. The study shows that the combination of the excessive positive dihedral effect produced by the winglets and adverse yaw due to aileron deflection can have a detrimental effect on the roll control characteristics of the airplane. Introduction of an aileron-rudder-interconnect, and reduction of the effective dihedral by canting-in of the winglets, or addition of a lower winglet can eliminate the roll control problems.

Van Dam, C. P.↗
DOE OSTI2021

Ab initio simulations on the pure Cr lattice stability at 0K: Verification with the Fe-Cr and Ni-Cr binary systems

Significant discrepancies have been observed and discussed on the lattice stability of Cr between the predictions from the ab initio calculations and the CALPHAD approach. In the current work, we carefully examined the possible structures for pure Cr and reviewed the history back from how Kaufman originally determined the Gibbs energy of FCC-Cr in the 1970s. The reliability of Cr lattice stability derived by the CALPHAD and ab initio approaches was systematically discussed. It is concluded that the Cr lattice stability based on the CALPHAD approach has large uncertainty. Meanwhile, we cannot claim that the ab initio H FCC-Cr is error-free as FCC-Cr is an unstable phase under ambient conditions. The present work shows that the ab initio HFCC-Cr can be a viable scientific approach. As both approaches have their limitations, the present work propose to integrate the ab initio results into the CALPHAD platform for the development of the next generation CALPHAD database. As a result, the Fe-Cr and Ni-Cr binary systems were chosen as two case studies demonstrating the capability to adopt the ab initio Cr lattice stability directly into the current CALPHAD database framework.

36 MATERIALS SCIENCE↗
NASA NTRS1946

Comparison of Wind-Tunnel and Flight Measurements of Stability and Control Characteristics of a Douglas A-26 Airplane

Tests in Langley pressure tunnel of model XA-26 bomber were compared with those of A-26B (twin-engine attack bomber) and showed that static longitudinal stability, indicated by elevator-fixed neutral points, and variation of elevator deflection in straight and turning flight were good. Airplane possessed improved stability at low speeds which was attributed to pronounced stalling at root of production wing. At rudder-force reversal at speeds higher than those in flight tests, agreement in rudder-fixed and rudder-free static directional stability was good. Hinge moment obtained at zero sideslip was satisfactory for determining aileron forces in sideslip.

SIDESLIPPING - DOUGLAS A-26↗
NASA NTRS1958

Aerodynamic Performance and Static Stability and Control of Flat-Top Hypersonic Gliders at Mach Numbers from 0.6 to 18

A study is made of aerodynamic performance and static stability and control at hypersonic speeds. In a first part of the study, the effect of interference lift is investigated by tests of asymmetric models having conical fuselages and arrow plan-form wings. The fuselage of the asymmetric model is located entirely beneath the wing and has a semicircular cross section. The fuselage of the symmetric model was centrally located and has a circular cross section. Results are obtained for Mach numbers from 3 to 12 in part by application of the hypersonic similarity rule. These results show a maximum effect of interference on lift-drag ratio occurring at Mach number of 5, the Mach number at which the asymmetric model was designed to exploit favorable lift interference. At this Mach number, the asymmetric model is indicated to have a lift-drag ratio 11 percent higher than the symmetric model and 15 percent higher than the asymmetric model when inverted. These differences decrease to a few percent at a Mach number of 12. In the course of this part of the study, the accuracy to the hypersonic similarity rule applied to wing-body combinations is demonstrated with experimental results. These results indicate that the rule may prove useful for determining the aerodynamic characteristics of slender configurations at Mach numbers higher than those for which test equipment is really available. In a second part of the study, the aerodynamic performance and static stability and control characteristics of a hypersonic glider are investigated in somewhat greater detail. Results for Mach numbers from 3 to 18 for performance and 0.6 to 12 for stability and control are obtained by standard text techniques, by application of the hypersonic stability rule, and/or by use of helium as a test medium. Lift-drag ratios of about 5 for Mach numbers up to 18 are shown to be obtainable. The glider studied is shown to have acceptable longitudinal and directional stability characteristics through the range of Mach numbers studied. Some roll instability (negative effective dihedral) is found at Mach numbers near 12.

Syvertson, Clarence A↗
NASA NTRS1985

Exploratory low-speed wind-tunnel study of concepts designed to improve aircraft stability and control at high angles of attack

A wind tunnel investigation of concepts to improve the high angle-of-attack stability and control characteristics of a high performance aircraft was conducted. The effect of vertical tail geometry on stability and the effectiveness of several conventional and unusual control concepts was determined. These results were obtained over a large angle-of-attack range. Vertical tail location, cant angle and leading edge sweep could influence both longitudinal and lateral-directional stability. The control concepts tested were found to be effective and to provide control into the post stall angle-of-attack region.

Hahne, D. E.↗
NASA NTRS1953

Flight Measurements of the Stability Characteristics of the Bell X-5 Research Airplane in Sideslips at 59 Deg Sweepback

Flight measurements of the stability characteristics of the Bell X-5 research airplane at 59 deg sweepback were made in steady sideslips at Mach numbers from 0.62 to 0.97 at altitudes ranging between 35,000 and 40,000 feet. The results showed that the apparent directional stability was positive and increased at Mach numbers above 0.90. The apparent effective dihedral was positive and high, increasing at Mach numbers above 0.75. The cross-wind force coefficient per degree of sideslip was positive and increased rapidly at Mach numbers above 0.94.

Childs, Joan M↗
NASA NTRS1949

A simplified method for the determination and analysis of the neutral-lateral-oscillatory-stability boundary

A necessary condition for neutral oscillatory stability is that Routh's discriminant r, formed from the coefficients of the stability equation, is equal to zero. Computations obtained from rsub1=0 and d=0 show very good agreement with the results calculated by the expression for r=0. The nature of the modes of motion as a function of the directional-stability derivative and the effective-dihedral derivative is discussed in detail.

Sternfield, Leonard↗