Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS, STAINLESS - REZISTAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗
NASA NTRS1976

Cross sections for He and Ne isotopes in natural Mg, Al, and Si, He isotopes in CaF2, Ar isotopes in natural Ca, and radionuclides in natural Al, Si, Ti, Cr, and stainless steel induced by 12- to 45-MeV protons

Stacks of thin Mg, Al, Si, Ca, CaF2, Ti, and stainless steel foils were bombarded in twelve irradiations by a variable energy cyclotron. Cross sections are reported for He and Ne in natural Mg, Al, and Si, and for He in CaF2, and for Ar in natural Ca, as determined from mass spectrometer analysis of the inert gases. In addition, cross sections of Na-22 in natural Al and Si, of V-48 in natural Ti, and of Cr-51, Mn-52, and Co-57 in stainless steel are reported. From these were deduced Cr-51 and Mn-52 cross sections in natural Cr.

Walton, J. R.↗
DOE OSTI2023

Collaborative Study on Weldability of Irradiated Stainless Steel 304 Materials Removed from The NRU Reactor

A collaborative research on developing advanced welding technologies for irradiated stainless steel 304 materials between CNL and ORNL has been established to support both U.S. and Canadian interests in evaluation of weld repair techniques on irradiated materials to support continuous operation of commercial nuclear power. The work utilizes unique material from the National Research Universal (NRU) reactor and the specialized welding hot cell facility at ORNL. The objective is to explore suitable welding technique and parameters and to determine the helium concentration limitation in terms of irradiated stainless-steel weldability. An additional objective is to develop the knowledge and understanding of cracking mechanisms induced by high concentration of helium in the process of weld repair of the irradiated structural alloys. This report summarizes the experimental welding evaluation on irradiated material from the NRU reactor containing helium concentrations ranging from 12 to 45 atomic parts per million (appm).

36 MATERIALS SCIENCE↗
DOE OSTI2022

The study of local overheating and plasma formation on stainless steel z-pinch targets

Plasma formation from intensely ohmically heated conductors is known to be highly non-uniform, as local overheating can be driven by micron-scale imperfections. Detailed understanding of plasma formation is required to predict the performance of magnetically driven physics targets and magnetically-insulated transmission lines (MITLs). Previous LDRD-supported work (projects 178661 and 200269) developed the electrothermal instability (ETI) platform, on the Mykonos facility, to gather high-resolution images of the self-emission from the non-uniform ohmic heating of z-pinch rods. Experiments studying highly inhomogeneous alloyed aluminum captured complex heating topography. To enable detailed comparison with magnetohydrodynamic (MHD) simulation, 99.999% pure aluminum rods in a z-pinch configuration were diamond-turned to ~10nm surface roughness and then further machined to include well-characterized micron-scale "engineered" defects (ED) on the rod's surface (T.J. Awe, et al., Phys. Plasmas 28, 072104 (2021)). In this project, the engineered defect hardware and diagnostic platform were used to study ETI evolution and non-uniform plasma formation from stainless steel targets. The experimental objective was to clearly determine what, if any, role manufacturing, preparation, or alloy differences have in encouraging nonuniform heating and plasma formation from high-current density stainless steel. Data may identify improvements that may be implemented in the fabrication/preparation of electrodes used on the Z machine. Preliminary data shows that difference in manufacturer has no observed effect on ETI evolution, stainless alloy 304L heated more uniformly than alloy 310 at similar current densities, and that stainless steel undergoes the same evolutionary ETI stages as ultra-pure aluminum, with increased emission tied to areas of elevated surface roughness.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Diffusion brazing nickel-plated stainless steel

To bond parts, sandwich assembly is made up of aluminum core, aluminum face sheet with brazing alloy interface, and nickel plated stainless steel part. Sandwich is placed between bottom and top glide sheet that is placed in stainless steel retort where assembly is bonded at 580 C.

Beuyukian, C. S.↗
DOE OSTI2025

Tailoring composition and deformation modes at the microstructural level for next generation low-cost high-strength austenitic stainless steels

The objective of this project is to enable deliberate development of cost-effective, hydrogen resistant alloys by establishing detailed relationships specific to the effects of alloy composition, short-range order (SRO), and microsegregation in the presence of hydrogen on the transition between homogeneous deformation and localized plasticity in shear bands. In collaboration with the International Institute for Carbon-Neutral Energy Research, I2CNER, at Kyushu University in Japan, we conceptualized, designed, and manufactured four austenitic alloys that maintain corrosion resistance and ensure lower cost relative to baseline commercial alloys. The mechanical properties and deformation modes of the novel alloys (KU alloys) were assessed in the presence of hydrogen (H). Correlations between composition and performance revealed that two of the KU alloys are suitable replacements for 316 steel, while another is a viable replacement for 304 steel at room temperature. We found that, in the presence of other austenite stabilizing elements namely Mn and N, replacing Ni with Cu does not lead to martensite formation as has been previously reported.1–3 Furthermore, we found that the addition of Cu leads to an earlier onset of multiple slip resulting in an relative earlier onset of a higher work hardening rate (WHR). Greater understanding of the relationships between alloy composition and SRO required the development of a novel advanced electron diffraction methodology to characterize SRO in complex FCC alloys. This innovative approach, which combines fluctuation and correlation analyses of diffuse-scattering signals, successfully differentiated between SRO and long-range ordering (LRO). Further investigations into annealed austenitic stainless steels could provide insights into manipulating SRO and its effects on material properties. Atomistic simulations provided understanding of SRO behavior that was difficult to capture experimentally. This project created the first spin cluster expansion model that is able to capture and describe SRO effects in Fe-Ni-Cr FCC alloys, accounting for the non-negligible effects of magnetism. An automated computational workflow was established to provide reliable predictions of SRO in Fe-Ni-Cr austenitic alloys, both with and without the presence of H atoms. Analysis of the propensity for SRO in Fe-Ni-Cr alloys revealed that H tends to cluster with specific, well-defined SRO domains. The computational framework is general purpose and can be extended to realistic stainless steels across diverse composition ranges. With confidence that SRO is possible in austenitic stainless steels, we developed a discrete dislocation finite element code to understand the interaction of dislocations with SRO in the presence of H. By incorporating H effects on the dislocation emission and SRO stress field we show that the critical stress for the dislocation pileup to breakthrough the SRO domain decreases in the presence of H, which directly contributes localized deformation at the macroscale. Through the simulation of a uniaxial tension test, we demonstrated that H-induced weakening of SRO stress field and H-enhanced dislocation emission can lead to the onset of shear localization at lower macroscopic strains. As a whole, this project identified three novel alloys that show improvements in performance and cost efficiency for H-facing applications by studying correlations between alloy chemistry and deformation behavior. We also made significant advancements to experimental and computational methodologies necessary to study the chemistry and distribution of SRO across a range of alloys, which in turn allowed us to demonstrate how deformation mechanisms change due to the contributions of SRO in austenitic alloys in the presence of H. The combined advancements in fundamental understanding with novel alloy development in this project has increased the viability of next generation H-technologies for the broader public through accessible low-cost alloys and accelerated development towards future H-infrastructure.

08 HYDROGEN↗
DOE OSTI2023

Investigation of the Effect of Chrome and Nickel Concentrations During Two-Piston Splat Quenching of Austenitic Stainless Steels

For solidification rates at or near equilibrium solidification conditions the effects of chrome (Cr) and nickel (Ni) on stainless steel solidification modes and microstructures are well detailed. However, fusion-based additive manufacturing (FBAM) processes that rely on faster, more rapid solidification rates call for a more in-depth understanding of the effects of rapid solidification on the solidification behavior and how these change with variations in alloy composition. Eleven custom stainless steel (SS) alloys with unique compositions based on 316L were made using targeted alloying element additions to generate feedstock with Cr/Ni eq ratios ranging from 0.9 to 2.1. Two-piston splat quenching (SQ) was used to produce rapid solidification conditions similar to those achieved in powder bed fusion processes in a fraction of the time and cost of traditional methods. Employing heat transfer simulations, SEM, TEM, and STEM characterization techniques, the SQ process was found to consistently produce solidification rates estimated to be between ~ 0.4 and 1.6 m/s. Five unique solidification microstructures were identified within the rapidly solidified SQ samples (primary austenite, massively transformed ferrite to austenite, primary austenite and massively transformed ferrite to austenite, primary ferrite, and primary ferrite and massively transformed ferrite to austenite). Both the primary ferrite solidification mode and primary ferrite phase were found to form at lower Cr/Ni eq values than previously predicted. SQ samples with compositions that were within the compositional specifications for 316L SS, an alloy which is commonly used in FBAM processes, demonstrated a wider range of potential solidification modes and microstructures that could form at rapid solidification rates than expected. Finally, by using SQ as a means to simulate rapid solidification conditions similar to those observed in FBAM processes, potential new alloy compositions can be screened faster and more cost effectively than purchasing and running test batches of the metallic powder.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interfacial microstructure and mechanical properties of rotary inertia friction welded dissimilar 422 martensitic stainless steel to 4140 low alloy steel joints

In this work, dissimilar rotary inertia friction welds between 422 martensitic stainless steel and 4140 martensitic low-alloy steel were made to fabricate prototype heavy-duty diesel engine pistons. The influence of the inertia friction welding process and post weld heat treatment (PWHT) temperature on the interfacial microstructure evolutions and corresponding effects on mechanical properties of the 422/4140 welds were evaluated in detail. Carbon diffused from the 4140 side to the 422 side during PWHT at 650 °C for 1.5 h, causing the formation of a hard carbide-rich layer on the 422 side, and a softer but discontinuous C-depleted layer the 4140 side. PWHT at 700 °C for 1.5 h greatly accelerated C diffusion across the interface relative to 650 °C, resulting in a thicker hard carbide-rich layer and a relatively thick and continuous layer of coarse C-depleted grains (ferrite) on the 4140 side. In addition, the PWHT temperature greatly influenced the tensile properties and fracture behavior of the welds, with the 650 °C PWHT-ed samples failing predominately in a ductile manner in the 4140 heat affected zone during tensile testing. Conversely, the 700 °C PWHT specimens exhibited a strength reduction compared with the 650 °C PWHT specimens because of additional coarsening of the interfacial ferrite layer and softening of the base materials during PWHT, with brittle fracture between the hard and soft layers the predominate failure mechanism. Based on the findings, a reduced PWHT temperature and/or time, minimizing the hardness differential of the base metals, and pre-heating the 422 steel prior to welding are the potential pathways to achieve a more optimal balance between desirable tempering and stress relief of the weld microstructure and undesirable C migration across the weld interface, and to reduce the strength mismatch across the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Additive manufacturing as a new processing technique can produce unique microstructure that is difficult to achieve using conventional techniques. Here, we have investigated the creep behavior of 316 L stainless steel produced by a laser powder bed fusion process at temperatures of 550, 600 and 650 °C and stresses between 175 and 300 MPa. We found that additively-manufactured 316 L stainless steel had a higher stress dependence of the minimum creep rate than conventionally-made Type 316 SS, which could be attributed to the dislocation cell structure resulting from the printing process. The dislocation cell structure was unstable under creep, evolving into a uniform dislocation structure under the test conditions. While internal porosity in AM 316 L SS may serve as nucleation sites of creep voids and may be responsible for a relatively lower creep life, additively-manufactured 316 SS did not show inferior creep ductility when compared with conventionally-made 316 SS. The creep life of AM 316 L SS could be improved by stabilizing dislocation cell structure and/or reducing internal porosity through an optimized additive manufacturing process.

316 L stainless steel↗
DOE OSTI2025

Long-term thermal aging behavior and strength reduction in a laser powder bed fusion 316H stainless steel

The long-term thermal stability of structural alloys is essential for ensuring the safe and reliable operation of nuclear reactors and other power plants. While extensive research has explored the effects of thermal aging on conventional stainless steels, the behavior of additively manufactured (AM) alloys remains less understood. This study examines the thermal aging response of laser powder bed fusion (LPBF) 316H stainless steel (SS) at temperatures ranging from 550 °C to 750 °C over durations of up to 10,000 h (approximately 1.14 years). Advanced characterization techniques, including electron microscopy and synchrotron X-ray diffraction, were used to investigate dislocation recovery and phase evolution. Based on these findings, a time-temperature-precipitation (TTP) diagram was developed for LPBF 316H SS, revealing a 10- to100-fold acceleration in precipitation kinetics compared to wrought 316H SS. A physics-informed model was calibrated using the short-term experimental data, enabling predictions of average precipitate sizes, volume fractions of M 23 C 6 and Laves phases, and changes in molybdenum solute concentration for aging up to 1 × 10⁶ h (114 years). These microstructural insights were further utilized to estimate yield strength and extrapolate strength reduction factors over the extended aging period. Despite the accelerated aging kinetics, LPBF 316H SS demonstrated superior yield strength retention compared to its wrought counterpart. In conclusion, this study establishes a framework for evaluating long-term performance using short-term experimental data and supports the accelerated qualification of AM materials for high-temperature structural applications.

Laser powder bed fusion↗
NASA NTRS1990

A porous stainless steel membrane system for extraterrestrial crop production

A system was developed in which nutrient flow to plant roots is controlled by a thin (0.98 or 1.18 mm) porous (0.2 or 0.5 microns) stainless steel sheet membrane. The flow of nutrient solution through the membrane is controlled by adjusting the relative negative pressure on the nutrient solution side of the membrane. Thus, the nutrient solution is contained by the membrane and cannot escape from the compartment even under microgravity conditions if the appropriate pressure gradient across the membrane is maintained. Plant roots grow directly on the top surface of the membrane and pull the nutrient solution through this membrane interface. The volume of nutrient solution required by this system for plant growth is relatively small, since the plenum, which contains the nutrient solution in contact with the membrane, needs only to be of sufficient size to provide for uniform flow to all parts of the membrane. Solution not passing through the membrane to the root zone is recirculated through a reservoir where pH and nutrient levels are controlled. The size of the solution reservoir depends on the sophistication of the replenishment system. The roots on the surface of the membrane are covered with a polyethylene film (white on top, black on bottom) to maintain a high relative humidity and also limit light to prevent algal growth. Seeds are sown directly on the stainless steel membrane under the holes in the polyethylene film that allow a pathway for the shoots.

NASA Discipline Number 61-20↗
DOE OSTI2024

First-principles and cluster expansion study of the effect of magnetism on short-range order in Fe–Ni–Cr austenitic stainless steels

Short-range order (SRO), the regular and predictable arrangement of atoms over short distances, alters the mechanical properties of technologically relevant structural materials such as medium/high entropy alloys and austenitic stainless steels. In this study, we present a generalized spin cluster expansion (CE) model and show that magnetism is a primary factor influencing the level of SRO present in austenitic Fe-Ni-Cr alloys. The spin CE consists of a chemical cluster expansion combined with an Ising model for Fe-Ni-Cr austenitic alloys. It explicitly accounts for local magnetic exchange interactions, thereby capturing the effects of finite temperature magnetism on SRO. Model parameters are obtained by fitting to a first-principles data set comprising both chemically and magnetically diverse FCC configurations. The magnitude of the magnetic exchange interactions are found to be comparable to the chemical interactions. Compared to a conventional implicit magnetism CE built from only magnetic ground state configurations, the spin CE shows improved performance on several experimental benchmarks over a broad spectrum of compositions, particularly at higher temperatures due to the explicit treatment of magnetic disorder. We find that SRO is strongly influenced by alloy Cr content, since Cr atoms prefer to align antiferromagnetically with nearest neighbors but become magnetically frustrated with increasing Cr concentration. Using the spin CE, we predict that increasing the Cr concentration in typical austenitic stainless steels promotes the formation of SRO and increases order-disorder transition temperatures. Furthermore, this study underscores the significance of considering magnetic interactions explicitly when exploring the thermodynamic properties of complex transition metal alloys. It also highlights guidelines for customizing SRO through adjustments of alloy composition.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of oxygen evolution reaction with 316 and 304 stainless-steel mesh electrodes in natural seawater electrolysis

Here, two commercially available stainless steel mesh substrates (316 SS and 304 SS) were evaluated as electrodes for oxygen evolution reaction (OER) in natural seawater electrolysis. The results show the 304 SS is less stable against corrosion under neutral (pH of 8.5) and low alkaline (0.1 M NaOH, pH of 12.8) seawater electrolytes because of the direct metal dissolution and chlorine evolution reaction (CER), and the 316 SS is superior to 304 SS in terms of electrocatalytic activity and resistance to corrosion under the same media. The performance of 304 SS is comparable to 316 SS under the high alkaline (1 M NaOH, pH of 13.7) seawater electrolyte, where the CER and metal dissolution are suppressed by OER. The overpotential for 304 and 316 SS is around 430 mV at 10 mA cm -2 , and the Tafel slopes are below 50 mV dec -1 under the high alkaline (1 M NaOH) seawater electrolyte, showing promising performance. The poor resistance to corrosion of 304 SS is attributed to the low Mo content, and it is supposed that the stability of both 304 and 316 SS can be improved further with the addition of Mo content. This work expands on promising substrates for natural seawater electrolysis, with cost and performance advantages.

Stainless-steel mesh↗
NASA NTRS1977

Oxidation and corrosion behavior of modified-composition, low-chromium 304 stainless steel alloys

The effects of substituting less strategic elements than Cr on the oxidation and corrosion resistance of AISI 304 stainless steel were investigated. Cyclic oxidation resistance was evaluated at 870 C. Corrosion resistance was determined by exposure of specimens to a boiling copper-rich solution of copper sulfate and sulfuric acid. Alloy substitutes for Cr included Al, Mn, Mo, Si, Ti, V, Y, and misch metal. A level of about 12% Cr was the minimum amount of Cr required for adequate oxidation and corrosion resistance in the modified composition 304 stainless steels. This represents a Cr saving of at least 33%. Two alloys containing 12% Cr and 2% Al plus 2% Mo and 12% Cr plus 2.65% Si were identified as most promising for more detailed evaluation.

Stephens, J. R.↗
NASA NTRS2017

Cryogenic Thermal Emittance Measurements on Small-Diameter Stainless Steel Tubing

The Mid Infrared Instrument aboard the James Webb Space Telescope includes a mechanical cryocooler which cools its detectors to their 6 K operating temperature. The refrigerant flows through several meters of 2 mm diameter 304L stainless steel tubing, with some sections gold plated, and some not, which are exposed to their environment. An issue of water freezing onto the tube surfaces is mitigated by running a warm gas through the lines to sublimate the frozen water. To model the effect of this process on nearby instruments, an accurate measure of the tube emittance is needed. Previously we reported the absorptance of the gold plated stainless steel tubing as a function of source temperature (i.e. its environment). In this work the thermal emittance of the uncoated tubing is measured as a function of its temperature between 100 and 280 K. These values lead to an accurate prediction of the minimum length of time required to thermally recycle the system. We report the technique and present the results.

stainless steel↗