Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Calculation of turbulent shear stress in supersonic boundary layer flows

An analysis of turbulent boundary layer flow characteristics and the computational procedure used are discussed. The integrated mass and momentum flux profiles and differentials of the integral quantities are used in the computations so that local evaluation of the streamwise velocity gradient is not necessary. The computed results are compared with measured shear stress data obtained by using hot wire anemometer and laser velocimeter techniques. The flow measurements were made upstream and downstream of an adiabatic unseparated interaction of an oblique shock wave with the turbulent boundary layer on the flat wall of a two dimensional wind tunnel. A comparison of the numerical analysis and actual measurements is made and the effects of small differences in mean flow profiles on the computed shear stress distributions are discussed.

Sun, C. C.↗
NASA NTRS1980

Mode I fracture behavior of nonlinear materials

A finite element analysis is presented for the Mode I fracture behavior of cracked plates (stationary crack) made of different nonlinear materials (elastoplastic or elastic locking). The assumed stress-strain behavior of the nonlinear materials was piecewise linear. For each given 'stationary' crack size, the corresponding critical remote tensile stress was calculated based on the maximum crack-tip stress failure criterion. It was found that in the log-log plots of the critical remote stress versus critical crack length, the fracture data of the piecewise linear materials obey a 'stepwise-linear-inverse-square-root' fracture law. It is also shown how the fracture data of the piecewise linear materials can be fitted by proper piecewise graphical shifting of the classical 'inverse-square-root' fracture curve for the linearly elastic materials.

Ko, W. L.↗
NASA NTRS1987

Dislocation dynamics of web type silicon ribbon

Silicon ribbon grown by the dendritic web process passes through a rapidly changing thermal profile in the growth direction. This rapidly changing profile induces stresses which produce changes in the dislocation density in the ribbon. A viscoplastic material response function (Haasen-Sumino model) is used herein to calculate the stresses and the dislocation density at each point in the silicon ribbon. The residual stresses are also calculated.

Dillon, O. W., Jr.↗
NASA NTRS1943

Least-work analysis of the problem of shear lag in box beams

The distribution of stress in the cover sheets of thin-wall box beams is analyzed, with regard to the effect of shear deformation in the cover sheets, by the method of least work. Explicit results are obtained for a number of representative cases that show the influence of the following factors on the stress patterns. (1) Variation of stress in spanwise direction as given by elementary beam theory. (2) Value of a parameter called shear-lag aspect ratio which designates the product of span-width ratio of the beam and of the square root of the ratio of effective shear modulus and tensing modulus of the cover sheets. (3) Value of ratio of cover-sheet stiffness to side-web stiffness. (4) Variation of beam height in span direction. (5) Variation of beam width in span direction. (6) Variation of cover-sheet thickness in span direction. General conclusions are drawn from the results obtained. Among them the most important one appears to be the fact that the shear-lag effect depends primarily on the following tow quantities: (1) the value of the shear-lag aspect ratio. (2) the shape of the curve representing the product of the stress of elementary beam theory and of the cover-sheet thickness.

STRESS CALCULATIONS, LEAST-WORK↗
NASA NTRS1951

Calculation of the bending stresses in helicopter rotor blades

A comparatively rapid method is presented for determining theoretically the bending stresses of helicopter rotor blades in forward flight. The method is based on the analysis of the properties of a vibrating beam, and its uniqueness lies in the simple solution of the differential equation which governs the motion of the bent blades.

De Guillenchmidt, P↗
NASA NTRS1931

Wrinkling of reinforced plates subjected to shear stresses

An analysis is made here of the problem of long plates with transverse stiffeners subject to shear. A typical example would be a long Wagner beam. The shear stress is calculated at which the web wrinkles and shear stress becomes a maximum. The equation is solved for both a condition of free support and rigidity of support on the edges.

Seydel, Edgar↗
NASA NTRS1983

A nonlinear fracture mechanics approach to the growth of small cracks

An analytical model of crack closure is used to study the crack growth and closure behavior of small cracks in plates and at notches. The calculated crack opening stresses for small and large cracks, together with elastic and elastic plastic fracture mechanics analyses, are used to correlate crack growth rate data. At equivalent elastic stress intensity factor levels, calculations predict that small cracks in plates and at notches should grow faster than large cracks because the applied stress needed to open a small crack is less than that needed to open a large crack. These predictions agree with observed trends in test data. The calculations from the model also imply that many of the stress intensity factor thresholds that are developed in tests with large cracks and with load reduction schemes do not apply to the growth of small cracks. The current calculations are based upon continuum mechanics principles and, thus, some crack size and grain structure exist where the underlying fracture mechanics assumptions become invalid because of material inhomogeneity (grains, inclusions, etc.). Admittedly, much more effort is needed to develop the mechanics of a noncontinuum. Nevertheless, these results indicate the importance of crack closure in predicting the growth of small cracks from large crack data.

Newman, J. C., Jr.↗
NASA NTRS1989

Calculation of turbulence-driven secondary motion in ducts with arbitrary cross section

Calculation methods for turbulent duct flows are generalized for ducts with arbitrary cross-sections. The irregular physical geometry is transformed into a regular one in computational space, and the flow equations are solved with a finite-volume numerical procedure. The turbulent stresses are calculated with an algebraic stress model derived by simplifying model transport equations for the individual Reynolds stresses. Two variants of such a model are considered. These procedures enable the prediction of both the turbulence-driven secondary flow and the anisotropy of the Reynolds stresses, in contrast to some of the earlier calculation methods. Model predictions are compared to experimental data for developed flow in triangular duct, trapezoidal duct and a rod-bundle geometry. The correct trends are predicted, and the quantitative agreement is mostly fair. The simpler variant of the algebraic stress model procured better agreement with the measured data.

Demuren, A. O.↗
NASA NTRS1990

Calculation of turbulence-driven secondary motion in ducts with arbitrary cross-section

Calculation methods for turbulent duct flows are generalized for ducts with arbitrary cross-sections. The irregular physical geometry is transformed into a regular one in computational space, and the flow equations are solved with a finite-volume numerical procedure. The turbulent stresses are calculated with an algebraic stress model derived by simplifying model transport equations for the individual Reynolds stresses. Two variants of such a model are considered. These procedures enable the prediction of both the turbulence-driven secondary flow and the anisotropy of the Reynolds stresses, in contrast to some of the earlier calculation methods. Model predictions are compared to experimental data for developed flow in triangular duct, trapezoidal duct and a rod-bundle geometry. The correct trends are predicted, and the quantitative agreement is mostly fair. The simpler variant of the algebraic stress model procured better agreement with the measured data.

Demuren, A. O.↗
NASA NTRS1981

The axisymmetric elasticity problem for a laminated plate containing a circular hole

The elasticity problem for a laminated thick plate which consists of two bonded dissimilar layers and which contains a circular hole is considered. The problem is formulated for arbitrary axisymmetric tractions on the hole surface by using the Love strain function. Through the expansion of the boundary conditions into Fourier series the problem is reduced to an infinite system of algebraic equations which is solved by the method of reduction. Of particular interest in the problem are the stresses along the interface as they relate to the question of delamination failure of the composite plate. These stresses are calculated and are observed to become unbounded at the hole boundary. An approximate treatment of the singular behavior of the stress state is presented and the stress intensity factors are calculated.

Delale, F.↗
NASA NTRS1984

Elevated temperature compressive steady state deformation and failure in the oxide dispersion strengthened alloy MA 6000E

The compressive flow strength-strain rate behavior of the oxide-dispersion-strengthened alloy MA 6000E has been studied in the temperature range 1144-1366 K, with strain rates ranging from 2.1 x 10 to the -5th to 2.1 x 10 to the -7th per s. It is found that the inherent strength of the alloy is essentially the same in all test directions and that the low strength observed in tensile tests results from the inability of grain boundaries to support high tensile stresses. The failure of MA 6000E under high-temperature, slow plastic flow conditions is shown to be the result of concentrated slip. Slow plastic deformation in MA 6000E can be described by a threshold stress model of creep where threshold stresses are calculated from relatively fast testing procedures and the effective stress exponent for creep is assumed to be 3.5.

Whittenberger, J. D.↗
NASA NTRS1985

Analysis of silicon stress/strain relationships

In the study of stress-strain relationships in silicon ribbon, numerous solutions were calculated for stresses, strain rates, and dislocation densities through the use of the Sumino model. It was concluded that many cases of failure of computer solutions to converge are analytical manifestations of shear bands (Luder's band) observed in experiments.

Dillon, O.↗
NASA NTRS1999

Analysis of an Interface Crack for a Functionally Graded Strip Sandwiched between Two Homogeneous Layers of Finite Thickness

The interface crack problem for a composite layer that consists of a homogeneous substrate, coating and a non-homogeneous interface was formulated for singular integral equations with Cauchy kernels and integrated using the Lobatto-Chebyshev collocation technique. Mixed-mode Stress Intensity Factors and Strain Energy Release Rates were calculated. The Stress Intensity Factors were compared for accuracy with relevant results previously published. The parametric studies were conducted for the various thickness of each layer and for various non-homogeneity ratios. Particular application to the Zirconia thermal barrier on steel substrate is demonstrated.

Shbeeh, N. I.↗
NASA NTRS1979

Nonlinear temperature dependent failure analysis of finite width composite laminates

A quasi-three dimensional, nonlinear elastic finite element stress analysis of finite width composite laminates including curing stresses is presented. Cross-ply, angle-ply, and two quasi-isotropic graphite/epoxy laminates are studied. Curing stresses are calculated using temperature dependent elastic properties that are input as percent retention curves, and stresses due to mechanical loading in the form of an axial strain are calculated using tangent modulii obtained by Ramberg-Osgood parameters. It is shown that curing stresses and stresses due to tensile loading are significant as edge effects in all types of laminate studies. The tensor polynomial failure criterion is used to predict the initiation of failure. The mode of failure is predicted by examining individual stress contributions to the tensor polynomial.

Nagarkar, A. P.↗
NASA NTRS1992

Thermal residual stresses in silicon-carbide/titanium (0/90) laminate

The current work formulated a micromechanical analysis of a cross-ply laminate and calculated the thermal residual stress in a very thick (0/90)(sub 2n) silicon-carbide/titanium laminate. Results were also shown for a unidirectional laminate of the same material. Discrete fiber-matrix models assuming a rectangular array of fibers with a fiber volume fraction of 32.5 percent and a three-dimensional, finite-element analysis were used. Significant differences in the trends and magnitudes for the fiber, matrix, and interface stresses were calculated for unidirectional and (0/90) models. Larger hoop stresses calculated for the (0/90) model indicate that it may be more susceptible to radial cracking when subjected to mechanical loading than the unidirectional model. The axial stresses in the matrix were calculated to be slightly larger for the (0/90) model. The compressive axial stresses in the fiber were significantly larger in the (0/90) model. The presence of the cross-ply in the (0/90) model reduced the constraint on the fiber, producing radial interface stresses that were less compressive, which could lead to earlier failure of the fiber-matrix interface.

Bigelow, C. A.↗