Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sample selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Development of Ti 3 SiC 2 MAX phase tubular structures for solar receiver applications

Solar receiver tubes are key components of concentrating solar-thermal power (CSP) systems that harvest solar energy. For better efficiency, the Gen3 CSP receivers, which collect heat into a heat transfer fluid, require a temperature exceeding 700 °C during operation and need to perform under extreme conditions of high temperature and high thermal stress. Operators are seeking CSP designs using new high-temperature structural materials with high thermal conductivity and high creep resistance to achieve a design life of 30 years and thus help recover the plant capital cost sooner. MAX phase materials, which consist of an early transition metal element, an A-group element, and carbon or nitrogen, are expected to exhibit high creep resistance as well as high fracture toughness. Here, in this paper, we describe fabricating both (1) dense Ti 3 SiC 2 MAX phase disks and (2) short-length tubes using field-assisted sintering technology (FAST). First, the disk samples that we fabricated are fully dense and contain ≈90 % Ti 3 SiC 2 MAX phase materials and ≈10 % TiC phase materials. We determined a flexure strength of 519 ± 32 MPa by conducting a four-point bending test at room temperature with rectangular bar samples of ≈100 % density. The thermal conductivity of the Ti 3 SiC 2 MAX phase samples, measured by light flashing analysis, decreases linearly from a value of 41 W . m -1 . K -1 at room temperature to a value of 36 W . m -1 . K -1 at 650 °C. A solar reflectance measurement of the Ti 3 SiC 2 MAX phase revealed that, temperature increases from 400 to 1400 °C, thermal emittance increases from 0.39 to 0.49, while selectivity decreases from 1.8 to 1.4, respectively. Whereas the surface oxidized MAX phase samples after 100 h exposure to air at 1000 °C exhibit that of SiC. Next, we discuss fabrication of the crack-free Ti 3 SiC 2 MAX phase tubular structures accomplished by using FAST processing in graphite bedding. A Ti 3 SiC 2 MAX phase content of > 95 % with traceable ≈3% remaining TiC phase and ≈15 % porosity were demonstrated after high-temperature annealing. An average fracture strength of ≈250 MPa was determined with Ti 3 SiC 2 MAX phase tubes of ≈85 % density by diametral compression testing at room temperature. Our work demonstrated that using FAST processing to produce Ti 3 SiC 2 MAX phase tubular structures for CSP receiver applications is a viable approach.

14 SOLAR ENERGY↗
DOE OSTI2025

How Do Uncertainties in Galaxy Formation Physics Impact Field-level Galaxy Bias?

Our ability to extract cosmological information from galaxy surveys is limited by uncertainties in the galaxy–dark matter halo relationship for a given galaxy population, which are governed by the intricacies of galaxy formation. To quantify these uncertainties, we examine quenched and star-forming galaxies using two distinct approaches to modeling galaxy formation: U$\scriptsize{NIVERSE}$M$\scriptsize{ACHINE}$, an empirical semianalytic model, and the I$\scriptsize{llustris}$TNG hydrodynamical simulation. We apply a second-order hybrid N-body perturbative bias expansion to each galaxy sample, enabling direct comparison of modeling approaches and revealing how uncertainties in the galaxy–halo connection affect bias parameters and non-Poisson noise across number densities and redshifts. Notably, we find that quenched and star-forming galaxies occupy distinct parts of the bias parameter space, and that the scatter induced from these different galaxy formation models is small when conditioned on similar selections of galaxies. We also detect the signature of assembly bias in our samples; this leads to small but significant deviations from analytic bias predictions, while assembly bias-removed samples match these predictions well. This work indicates that galaxy samples from a spectrum of reasonable, physically motivated models for galaxy formation give a relatively small range of field-level galaxy bias parameters. We estimate a set of priors from these models that should be useful in extracting cosmological constraints from luminous red galaxy– and emission line galaxy–like samples. Looking forward, careful estimates of the range of impacts of galaxy formation, for a given sample and cosmological analysis, will be an essential ingredient for extracting the most precise cosmological information from current and future large galaxy surveys.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Viability of Miniature Discs in LFA-427

Miniature disc samples pose challenging measuring conditions for laser flash analysis. With reductions in signal from lower radiosity and lower half-rise times from low thicknesses, optimal selections of coatings and laser parameters are critical in a successful measurement. This report explains the methodology in successfully measuring two different material types—metals and ceramics—in proper coating selection, laser parameters, and post analysis for each material, as well as applying it to un-irradiated uranium samples of each type (U-metal, UO 2 ). This was done through a combination of analysis techniques combining automatic commercial methods (Neztech) and manual methods for correcting laser pulse impact aberrations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Python Library for Monte Carlo Simulations with Ab Initio and Machine-Learned Interatomic Potentials

There is a growing need in the simulation community for software that provides a transparent, reproducible, usable, and extensible (TRUE) Monte Carlo (MC) simulation framework employing energies from ab initio methods and machine-learning interatomic potentials (MLIPs). We introduce a Python library (ASE-MC) that adds Monte Carlo functionality to the Atomic Simulation Environment (ASE) package. Now, we can combine the powerful tools used to build systems and perform ab initio and MLIP in ASE with MC simulation algorithms to sample the configurational space with a concise Python script. After presenting the design philosophy, we demonstrate the flexibility of our approach using selected examples. These example simulations include liquid water described with a message-passing MLIP in the canonical and isothermal–isobaric ensembles, sampling the characteristic dihedral angle of biphenyl and comparing an MLIP to first-principles calculations, and a grand canonical Monte Carlo simulation of ammonia adsorption on Pt(111). These examples showcase the main features of the software, which include flexibility in the choice of ab initio or MLIP engine, ab initio or MLIP grand canonical MC with cavity bias insertions and deletions, the ability to add custom MC moves to the move set, and how users can condense complex MC workflows into a single Python script. Finally, this library serves as a framework for reproducible Monte Carlo simulations, facilitating easy reproduction of the work and application to new systems.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Uncovering hidden bias in neutron diffraction residual strain measurements

When calculating residual strain via neutron or X-ray diffraction, uncertainties propagated from the peak fit are often inadequate to describe the true scatter of measurements about a singular strain state, such as one that should describe a macroscopic continuum. Because diffraction is inherently a selective process, orientation-dependent scatter arises from the sub-sampling of strong microstructure and strain gradients. This paper investigates the appropriateness of propagated uncertainties with reference to their original intention, i.e. noise about a mean value. Thirty-six unique orientations of strain measurements are taken at multiple locations within an additive friction-stir deposition component with fine-scale gradients (∼200 µm) of plastic strain, texture and residual elastic strain. Multiple strain and stress calculation pathways are compared: direct substitution of three measurements into Hooke's law, direct inversion of any six unique orientations into the strain state tensor and thirty-six measurement least-squares estimation. For the last two cases, the appropriateness of the uncertainty interval is statistically evaluated on the basis of a physical constraint: common agreement under the strain transformation law. For this sample, the direct inversion of six measurements retains a conservative estimate of the uncertainty. However, propagated uncertainties in the least-squares solution greatly underestimate the true experimental scatter. A simple pathway to estimate appropriate uncertainty intervals is suggested. These results demonstrate that the interpretation of uncertainty in residual strain is strongly dependent on intrinsic sample-dependent effects, and that oversampling orientations and statistical analysis can give more accurate results with realistic uncertainties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Search for pair production of heavy particles decaying to a top quark and a gluon in the lepton+jets final state in proton–proton collisions at $\sqrt{s}=13\,\text {Te}\hspace{-.08em}\text {V}$

A search is presented for the pair production of new heavy resonances, each decaying into a top quark (t) or antiquark and a gluon (g). The analysis uses data recorded with the CMS detector from proton–proton collisions at a center-of-mass energy of 13 TeV at the LHC, corresponding to an integrated luminosity of 138 fb -1 . Events with one muon or electron, multiple jets, and missing transverse momentum are selected. After using a deep neural network to enrich the data sample with signal-like events, distributions in the scalar sum of the transverse momenta of all reconstructed objects are analyzed in the search for a signal. No significant deviations from the standard model prediction are found. Upper limits at 95% confidence level are set on the product of cross section and branching fraction squared for the pair production of excited top quarks in the t* → tg decay channel. The upper limits range from 120 to 0.8 fb for a t* with spin-1/2 and from 15 to 1.0 fb for a t* with spin-3/2. These correspond to mass exclusion limits up to 1050 and 1700 GeV for spin-1/2 and spin-3/2 t* particles, respectively. These are the most stringent limits to date on the existence of t* → tg resonances.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Human limits in machine learning: prediction of potato yield and disease using soil microbiome data

Abstract Background The preservation of soil health is a critical challenge in the 21st century due to its significant impact on agriculture, human health, and biodiversity. We provide one of the first comprehensive investigations into the predictive potential of machine learning models for understanding the connections between soil and biological phenotypes. We investigate an integrative framework performing accurate machine learning-based prediction of plant performance from biological, chemical, and physical properties of the soil via two models: random forest and Bayesian neural network. Results Prediction improves when we add environmental features, such as soil properties and microbial density, along with microbiome data. Different preprocessing strategies show that human decisions significantly impact predictive performance. We show that the naive total sum scaling normalization that is commonly used in microbiome research is one of the optimal strategies to maximize predictive power. Also, we find that accurately defined labels are more important than normalization, taxonomic level, or model characteristics. ML performance is limited when humans can’t classify samples accurately. Lastly, we provide domain scientists via a full model selection decision tree to identify the human choices that optimize model prediction power. Conclusions Our study highlights the importance of incorporating diverse environmental features and careful data preprocessing in enhancing the predictive power of machine learning models for soil and biological phenotype connections. This approach can significantly contribute to advancing agricultural practices and soil health management.

Aghdam, Rosa↗
DOE OSTI2025

Quantitative Electron Beam‐Single Atom Interactions Enabled by Sub‐20‐pm Precision Targeting

The ability to probe and control matter at the picometer scale is essential for advancing quantum and energy technologies. Scanning transmission electron microscopy offers powerful capabilities for materials analysis and modification, but sample damage, drift, and scan distortions hinder single atom analysis and deterministic manipulation. Materials analysis and modification via electron–solid interactions can be transformed by precise delivery of electrons to a specified atomic location, maintaining the beam position despite drift, and minimizing collateral dose. Here a fast, low-dose, sub-20-pm precision electron beam positioning technique is developed, “atomic lock-on,” (ALO), which offers the ability to position the beam on a specific atomic column without previously irradiating that column. This technique is used to lock onto a single selected atomic location to repeatedly measure its weak electron energy loss signal despite sample drift. Moreover, electron beam-matter interactions in single atomic events are measured with μ s time resolution. This enables observation of single-atom dynamics, such as atomic bistability, revealing partially bonded atomic configurations and recapture phenomena. This opens prospects for using electron microscopy for high-precision measurements and deterministic control of matter for quantum technologies.

2D materials↗
DOE OSTI2026

Brightest Cluster Galaxy ellipticity as proxy for halo shape: Orientation bias, assembly bias, and potential selection effects in SZ-selected clusters

The orientation of triaxial galaxy clusters with respect to the line-of-sight is expected to be one of the prime sources of scatter and potential bias in optical observables (e.g., richness and weak-lensing signal) of galaxy clusters. In this work, we use the observed shape of the central Brightest Cluster Galaxy (BCG) as proxy for the orientation along the line-of-sight for clusters selected via the Sunyaev-Zel'dovich (SZ) effect from the South Pole Telescope (SPT) and Atacama Cosmology Telescope (ACT) surveys, matched to optically selected clusters from the Dark Energy Survey Year 3 (DES). We construct two samples of clusters that are designed to be identical in SZ mass estimate and redshift but with the roundest vs. the most elliptical BCGs, which we expect to correspond to BCGs (and clusters) with major axes aligned along the line-of-sight vs. in the plane of the sky, respectively. We find that the optical richness of round-BCG clusters is $\sim 10$% larger than that of elliptical-BCG clusters, in agreement with the expectation from projection effects and presenting the first such detection in data. The density profiles, however, are not in agreement with the expectation from projection effects: the 1-halo term (below $6~h^{-1}\rm{Mpc}$) of both the weak-lensing and galaxy density profiles are the same for the subsamples, contrary to previous studies based on X-ray selected clusters. In the 2-halo regime (above $6~h^{-1}\rm{Mpc}$), we find a significant excess of the elliptical-BCG cluster profiles compared to the round-BCG cluster profiles, which is the opposite of the expectation from numerical simulations. We hypothesize that the intrinsic shape of the BCG reflects not just the orientation angle, but also intrinsic properties of the cluster which can affect both the SZ signal and the amplitude of the 2-halo term.

Srinivasan, Radhakrishnan [SUNY, Stony Brook] (ORC↗
DOE OSTI2025

Efficient BiVO 4 /CoFeO x H y photoanodes using controlled annealing and conformal linear-sweep electrocatalyst photodeposition

Although monoclinic bismuth vanadate (BiVO 4 ) is a promising photoanode for solar water splitting, its practical use is hindered by imperfect photocurrent generation/collection, low photovoltage compared to the bandgap, and corrosion side reactions that limit durability. Here, we introduce a controlled-annealing sol–gel process for BiVO 4 thin-film photoanodes along with an optimized linear-sweep-voltammetry photodeposition of CoFeO x H y cocatalysts. The resulting BiVO 4 films annealed at 550 °C exhibited a photocurrent density of 4.1 mA/cm 2 at 1.23 V RHE under 1 sun AM 1.5G solar simulation and a low onset potential of 0.26 V RHE due to high majority carrier conductivity, a crystalline bulk with reduced defects as evidenced by x-ray photoelectron spectroscopy and photoluminescence lifetime analysis, and thus enhanced photocarrier collection. However, significant degradation in performance was found due to interfacial photocorrosion. To protect the surface and speed the oxygen-evolution reaction CoFeO x H y cocatalyst layers were deposited. By varying the number of consecutive sweeps and adjusting the applied bias range, an ultra-thin (~15 nm) CoFeO x H y cocatalyst layer was uniformly grown deposited over 30 cycles on the BiVO 4 surface. The resulting BiVO 4 /CoFeO x H y yielded 4.03 mA/cm 2 at 1.23 V RHE and onset potential of 0.24 V RHE , with stable operation (~15 % loss in photocurrent at 1.23 V RHE relative to ~60 % loss in the uncatalyzed control sample). These conformal CoFeO x H y catalytic layers function simultaneously to selectively collect photoexcited holes from the BiVO 4 , catalyze the water-oxidation reaction, and protect the BiVO 4 from photodegradation.

42 ENGINEERING↗
DOE OSTI2025

Litter production and foliar nutrient resorption in fast- and slow-growing tree species in the Central Amazon

Litterfall is crucial for forest maintenance, serving as a primary mechanism for nutrient return to the nutrient-poor soils of tropical forests. Foliar nutrient resorption likewise represents an important nutrient-conservation mechanism. Yet, little is known about how these processes vary between fast- and slow-growing species in post-logging areas of the Amazon forest. Here, the objective of this study was to quantify litterfall production and the resorption of foliar nutrients in fast-growing and slow-growing tree species of the Central Amazon, in a forest that was experimentally logged in 1987. The study was conducted from May 2022 to April 2023. Litterfall was collected biweekly using four collectors that were systematically distributed beneath the canopy of each monitored tree, totaling 72 collectors. Three fast-growing and three slow-growing species were selected, each with three replicates, totaling 18 monitored individuals. Species-specific samples of fresh (green) and senesced (litter) leaves were collected and analyzed for their nutrient content and resorption efficiency. Fast-growing species had a monthly leaf litter deposition of 13.53 ± 1.6 g m −2 month −1 , compared to 2.59 ± 0.4 g m −2 month −1 for slow-growing species. The average annual litter production across both functional types was 8.6 ± 2.6 Mg ha −1 year −1 . Nutrient inputs through litterfall were higher in fast-growing species for all elements, particularly nitrogen (N), with 21.92 ± 4.9 kg ha −1 year −1 . Phosphorus (P) and potassium (K) exhibited the highest foliar resorption. P resorption efficiency was 68.3 % in fast-growing species and 57.8 % in slow-growing species. For K, efficiencies were 59.0 % and 41.7 %, respectively. These results highlight the substantial role that fast-growing species play in restoring forest productivity in managed Amazon forests, both through higher litter deposition and nutrient fluxes, and through nutrient conserving-mechanisms such as foliar nutrient resorption.

Amazon forest↗
DOE OSTI2025

Soft X-ray Emission Spectroscopy of Phosphorus Compounds for Energy Conversion and Storage

Phosphorus (P) is a ubiquitous component of materials for energy conversion and storage. Despite the effectiveness of soft X-ray emission spectroscopy (XES) to characterize these complex materials, XES studies of P-containing compounds are still largely missing. In this investigation, the electronic structure and XES signatures from the P L 2,3 -edge are probed for nine solid-state P-containing compounds characterized by various oxidation states and chemical environments: GaP (3−) , InP (3−) , red-P (0) , H 3 P (3+) O 3 , Na 2 H 2 P 2 (4+) O 6 , H 3 P (5+) O 4 , KH 2 P (5+) O 4 , Na 2 HP (5+) O 4 , and InP (5+) O 4 . The XES spectrum of each material exhibits distinct spectral fingerprints, which provide a robust basis for the speciation of complex P-containing samples. Density functional theory calculations shed light on the electronic structure of selected materials and particularly on the effect of phosphorus-oxygen hybridization. This study provides a comprehensive understanding of P L 2,3 XES spectral fingerprints across a wide range of oxidation states and chemical environments. These data sets and insights pave the way for dedicated future work, such as in situ and operando investigations of P-containing compounds in energy-related applications, where speciation of P compounds is needed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Federal Workplace Charging Program Guide

The 2015 Fixing America's Surface Transportation (FAST) Act authorizes the installation, operation, and maintenance of electric vehicle supply equipment (EVSE) for the purpose of recharging employees' privately owned vehicles (POVs) under the custody or control of the General Services Administration (GSA) or a Federal agency. It requires the collection of fees to recover the costs of installing, operating, and maintaining this equipment and imposes reporting requirements. This program guide reviews those requirements, excerpts the relevant language in Appendix A, and describes when and how fees may be required to cover costs of electricity, network costs, EVSE units, and installations in various scenarios. This program guide is designed to support Federal agencies developing and refining workplace charging programs for employee POVs. While it provides guidance and best practices, it does not replace agencywide policies or agency-specific legal counsel. It contains a roadmap for agency workplace charging programs and defines roles and responsibilities. This guide explains how to determine the number of POVs likely to charge at a given site and contains a sample employee survey in Appendix B. It reviews EVSE planning, including unit selection and acquisition, charger location(s), accounting for available power capacity, using existing infrastructure, and funding an incentive program. It also discusses the costs associated with EVSE acquisition, installation, and network management. These costs inform the subsequently provided information, which describes how to amortize costs to determine appropriate fees for each charging session. The final two sections of this guide address aspects of ongoing program management that the facility coordinator should consider and the reporting requirements associated with the FAST Act. The insights in this guide are applicable to all agency-owned and GSA-leased buildings or facilities offering the use of EVSE or a 120-volt receptacle for the purpose of recharging an employee's POV. However, the FAST Act requirements typically do not apply to any building or facility operated and maintained by a third-party vendor offering the use of EVSE as part of a commercial building lease unless the agency is managing the station and/or energy on behalf of the building and collecting POV fees.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Measurement of muon antineutrino charged current - 0 meson scattering, using the NOvA Near Detector

Antineutrino interaction cross sections are, at present, poorly constrained, particularly regarding the role of multi-nucleon processes such as 2-particle 2-hole (2p2h) interactions. The associated crosssection systematic uncertainties represent a significant challenge for precision oscillation measurements, especially for the next generation of neutrino experiments such as DUNE. We present a new measurement of the muon antineutrino charged-current cross section without mesons in the final state, using the high-statistics data set of the NOvA Near Detector. The analysis employs a cut-based selection enhanced by machine learning techniques to isolate a high-purity sample dominated by quasielastic (QE) and 2p2h interactions. We present the cross section as a function of the kinetic energy and scattering angle of the outgoing muon. We also present measurements of more model-dependent kinematic variables such as the neutrino energy and momentum transfer, to better probe the underlying nuclear physics. The results are compared against various neutrino event generators to test the robustness of current interaction models.

Vockerodt, Kevin John [Ohio State U.; Queen Mary, ↗
DOE OSTI2026

pop-cosmos : redshifts and physical properties of KiDS-1000 galaxies

ABSTRACT Principled Bayesian inference of galaxy properties has not previously been performed for wide-area weak-lensing surveys with millions of sources. We address this gap by applying the pop-cosmos generative model to perform spectral energy distribution (SED) fitting for 4 million KiDS (Kilo-Degree Survey)-1000 galaxies. Calibrated on deep COSMOS2020 photometric data, pop-cosmos specifies a physically motivated prior over the galaxy population up to $z \simeq 6$ in stellar population synthesis (SPS) parameter space. Using the Speculator SPS emulator with GPU (graphics processing unit)-accelerated Markov Chain Monte Carlo sampling, we perform full posterior inference at 8.2 GPU seconds per galaxy, obtaining joint constraints on galaxy redshifts and physical properties. We validate photometric redshifts against $\sim \!185\,\!000$ KiDS galaxies cross-matched to Dark Energy Spectroscopic Instrument Data Release 1 spectroscopic samples, achieving low bias ($2\times 10^{-3}$), scatter ($\sigma _{\mathrm{MAD}}=0.03$), and outlier fraction (3.2 per cent) for the Bright Galaxy Survey, with comparable performance (bias $3\times 10^{-2}$, $\sigma _{\mathrm{MAD}}=0.05$, 1.0 per cent outliers) for luminous red galaxies (LRGs). Within the LRG sample, we identify massive, dusty, star-forming contaminants at $z \simeq 0.4$ satisfying standard colour selections for quenched populations. We infer trends in stellar mass, star formation, metallicity, and dust across five tomographic redshift bins consistent with established scaling relations. Using specific star formation rate constraints, we identify $\sim$7 per cent of KiDS-1000 galaxies as quenched, versus 37 per cent implied by conservative colour cuts. This enables the construction of weak-lensing samples defined by physical properties while mitigating intrinsic alignment systematics and preserving statistical power. Our analysis validates pop-cosmos out of sample, establishing it as a scalable approach for galaxy evolution and cosmological analyses with photometric surveys.

Halder, Anik [Institute of Astronomy and Kavli Ins↗
DOE OSTI2025

Trace Element Analyses of Micron-Size Particles and Statistical Determination of Minimum Detection Limits

Savannah River National Laboratory (SRNL) has developed expertise in producing homogeneous, ca. 1 m-diameter spherical particles of mixed-element components, wherein dopants can be varied from a trace constituent (ppm) to wt.% concentrations. The samples used for this work are nickel-doped cerium oxide microspheres produced by SRNL. They were initially selected as analogs for plutonium-doped uranium oxide particles and analyzed as part of a larger study to evaluate whether electron probe microanalyzers (EPMA) can be used to characterize nuclear materials as an alternative or complementary method to mass spectrometers. The five samples used in this study contained nominal compositions of 0, 0.004, 0.04, 0.4 and 4 wt.% Ni. They were analyzed by both an Agilent 7900 Q-ICP-MS at SRNL and the JEOL JXA8530F Plus EPMA at the University of Minnesota. In addition to EPMA results (calibrated with high-precision Q-ICP-MS analyses) suggesting that the EPMA could address outstanding nuclear material characterization needs, these samples 1) showcase the ability of the EPMA to quantify not just trace concentrations, but trace concentrations in microparticles (1 m diameter, Fig. 1), and 2) offer a unique opportunity to evaluate the methodology for assessing the minimum detection limits of EPMA analyses.

McSwiggen, Peter [JEOL USA, 11 Dearborn Road, Peab↗
DOE OSTI2026

Virtual refrigerant charge sensing algorithm for residential CO₂ heat pumps

Natural refrigerants are increasingly adopted in next-generation heat pump systems, among which CO₂ heat pumps have attracted significant attention. However, due to their high operating pressures, the leakage risk is higher, resulting in undercharge conditions and degraded heat pump performance. Thus, developing an accurate refrigerant charge level detection technique is necessary to guarantee safe and efficient operation. Although virtual refrigerant charge (VRC) level calculation algorithms for CO₂ heat pumps exist, they typically rely on empirically selected features without a systematic selection framework, leading to multicollinearity and potential overfitting, which limit their prediction accuracy and generalizability. To address these issues, this study proposes a VRC algorithm framework with a systematic feature selection method that identifies physically meaningful and statistically significant features, and is applied using a residential CO₂ heat pump as a case study. The method is extended from previous work on conventional refrigerants to account for charge behavior in CO₂ gas coolers. The selected features include gas cooler outlet density, evaporator pressure, and superheat temperature. The results demonstrate that the proposed feature selection method significantly improves prediction accuracy compared to existing VRC approaches. A relatively small training dataset (∼30 samples) is sufficient for feature identification and model development. The developed algorithm achieves less than 3% prediction error under both undercharge and overcharge conditions, representing reductions of 46.7% and 35.3% compared to two recent reference VRC algorithms for transcritical CO₂ heat pumps reported in the literature. The proposed algorithm and feature selection method enhance leakage detection capability, facilitate the deployment of CO₂ heat pump systems, and contribute to reduced energy waste and maintenance costs.

Guo, Fangzhou [Lawrence Berkeley National Laborato↗
DOE OSTI2026

Highly Efficient Selection of High-redshift Emission-line Galaxies for Future DESI-like Surveys with Deep Multiband Imaging

Emission-line galaxies (ELGs) are an important tracer of baryon acoustic oscillations (BAOs) and large-scale structure at z > 1. In this work, we investigate the feasibility of using deep wide-area multiband imaging (e.g., from the Rubin Observatory) to efficiently select high-redshift ELGs. Using Hyper Suprime-Cam grizy photometry and COSMOS2020 many-band photometric redshifts, we design simple color cuts guided by a probabilistic random forest classifier to select galaxies at z = 1.1–1.6. We then empirically test and refine these color cuts using two samples of galaxies with deep spectroscopy and broad color coverage obtained with the Dark Energy Spectroscopic Instrument (DESI). Compared to DESI ELGs at z = 1.1–1.6, we achieve a higher redshift-measurement success rate (89% versus 69%), a much higher correct redshift-range success rate (84% versus 34%), and a far higher net surface density yield (1372 deg −2 versus 660 deg −2 ). Combining our sample with current DESI ELGs would increase the net ELG number density by a factor of ∼2.5, moving it out of the shot-noise limited regime and reducing the uncertainties on the BAO scale parameter at z = 1.1–1.6 by a factor of ∼2 at the highest redshifts. We also test selections using shallower photometry and obtain qualitatively similar results.

Salcedo Hernandez, Yoquelbin [University of Pittsb↗