Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separated Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Injection Induced Mixing in Flows Separating From Smooth Surfaces

An analytic model for predicting the effect of unsteady local surface injection on the flow separating from a streamlined body at angle of attack is proposed. The model uses the premise that separation control results from enhanced mixing along the shear layer that develops between the main stream and the fluid in the underlying recirculation zone. High-Reynolds-number asymptotic methods are used to connect the unsteady surface injection to an instability wave propagating on the separating shear layer and then to the large-scale coherent structures that produce the increased mixing. The results is a tool that can guide the choice of fluid-actuator parameters to maximize flow-control effectiveness and may also facilitate computer-based numerical experiments.

Adamczyk, John J.↗
NASA NTRS1996

High Reynolds number analysis of an axisymmetric afterbody with flow separation

The ability of a three-dimensional Navier-Stokes method, PAB3D, to predict nozzle afterbody flow at high Reynolds number was assessed. Predicted surface pressure coefficient distributions and integrated afterbody drag are compared with experimental data obtained from the NASA-Langley 0.3 m Transonic Cryogenic Tunnel. Predicted afterbody surface pressures matched experimental data fairly closely. The change in the pressure coefficient distribution with Reynolds number was slightly over-predicted. Integrated afterbody drag was typically high compared to the experimental data. The change in afterbody pressure drag with Reynolds number was fairly small. The predicted point of flow separation on the nozzle was slightly downstream of that observed from oilflow data at low Reynolds numbers and had a very slight Reynolds number dependence, moving slightly further downstream as Reynolds number increased.

Carlson, John R.↗
NASA NTRS1980

A comprehensive comparison between experiment and prediction for a transonic turbulent separated flow

Attempts to predict surface pressure distributions on lifting surfaces have been relatively unsuccessful in the transonic regime when the shock wave is of sufficient strength to produce an extensive region of turbulent separated flow. For these conditions, the viscous flow behavior must be accurately described even to obtain reasonable predictions of surface pressure. The present paper addresses this problem. Detailed comparisons between prediction and experiment are made for a transonic, turbulent boundary-layer separation (freestream Mach number = 0.875) for which the turbulent flow properties (including the turbulent Reynolds stress) had been measured by the laser velocimeter technique from upstream of the separated region through reattachment. The flow was generated on an axisymmetric 'bump' model designed to simulate the flow on an airfoil at transonic conditions. The numerical methods used in the comparisons include the solution of the time-dependent, mass-averaged Navier-Stokes equations, and the solution of the compressible boundary-layer equations by the inverse method. Solutions were obtained for the well established Cebeci-Smith algebraic turbulence model and the more recently developed Wilcox-Rubesin two-equation turbulence model.

Johnson, D. A.↗
NASA NTRS1952

Transition caused by the laminar flow separation

An experimental investigation of the effects of the geometry of body surface, Reynolds number, stream turbulence, and a roughness element (wire) on the reattachment of separated laminar boundary-layer flow on a bent flat plate is presented and discussed. The flow mechanisms determining reattachment of the boundary layer are analyzed and discussed.

BOUNDARY LAYER CHARACTERISTICS - WING SECTIONS↗
NASA NTRS1956

Exploratory investigation of the use of area suction to eliminate air-flow separation in diffusers having large expansion angles

Tests were made at a mean inlet Mach number of 0.2 with area suction applied to conical diffusers with expansion angles of 30 degrees and 50 degrees and exit to inlet area ratios of 2. Air-flow separation was eliminated with suction mass flows of 3 and 4 percent of the inlet mass flows for the 30 degrees and 50 degrees diffusers, respectively.

DIFFUSERS, SUBSONIC↗
NASA NTRS1960

Transition Reynolds Numbers of Separated Flows at Supersonic Speeds

Experimental research has been conducted on the effects of wall cooling, Mach number, and unit Reynolds number on the transition Reynolds number of cylindrical separated boundary layers on an ogive-cylinder model. Results were obtained from pressure and temperature measurements and shadowgraph observations. The maximum scope of measurements encompassed Mach numbers between 2.06 and 4.24, Reynolds numbers (based on length of separation) between 60,000 and 400,000, and ratios of wall temperature to adiabatic wall temperature between 0.35 and 1.0. Within the range of tile present tests, the transition Reynolds number was observed to decrease with increasing wall cooling, increase with increasing Mach number, and increase with increasing unit Reynolds number. The wall cooling effect was found to be four times as great when the attached boundary layer upstream of separation was cooled in conjunction with cooling of the separated boundary layer as when only the separated boundary layer was cooled. Wall cooling of both the attached and separated flow regions also caused, in some cases, reattachment in the otherwise separated region. Cavity resonance present in the separated region for some model configurations was accompanied by a large decrease in transition Reynolds number at the lower test Mach numbers.

Larson, Howard K.↗
NASA NTRS1977

Use of simplified flow separation criteria for slotted flap preliminary design

From experimental correlations of airfoil and flap pressure distributions, it is observed that flow separation is likely to occur when the canonical pressure recovery coefficient (C sub pr) exceeds a critical value. A procedure is described for obtaining the C sub pr parameter from modified inviscid analysis. The procedure has been applied to preliminary design studies of a new slotted flap to determine the influence of shape and location. Experiments are planned to evaluate the flap designed by this procedure.

Wentz, W. H., Jr.↗
NASA NTRS1983

Dynamic Distortion in a Short S-Shaped Subsonic Diffuser with Flow Separation

An experimental investigation of the time varying distortion at the diffuser exit of a subscale HiMAT forebody and inlet was conducted at Mach 0.9 in the Lewis 8 by 6 foot Supersonic Wind Tunnel. A transitory separation was detected within the subsonic diffuser. Vortex generators were installed to eliminate the flow separation. Results from a study of the instantaneous pressure variations at the diffuser exit are presented. The time unsteady total pressures at the diffuser exit are computer interpolated and presented in the form of a movie showing the transitory separation. Limited data showing the instantaneous distortion levels is also presented.

Stumpf, R.↗
NASA NTRS1983

Dynamic distortion in a short s-shaped subsonic diffuser with flow separation

An experimental investigation of the time varying distortion at the diffuser exit of a subsonic HiMAT forebody and inlet was conducted at Mach 0.9 in the Lewis 8 by 6 foot Supersonic Wind Tunnel. A transitory separation was detected within the subsonic diffuser. Vortex generators were installed to eliminate the flow separation. Results from a study of the instantaneous pressure variations at the diffuser exit are presented. The time unsteady total pressures at the diffuser exit are computer interpolated and presented in the form of a movie showing the transitory separation. Limited data showing the instantaneous distortion levels are also presented. Previously announced in STAR as N83-26838

Stumpf, R.↗
NASA NTRS1974

Heat-transfer and pressure distributions for laminar separated flows downstream of rearward-facing steps with and without mass suction

Heat-transfer and pressure distributions were measured for laminar separated flows downstream of rearward-facing steps with and without mass suction. The flow conditions were such that the boundary-layer thickness was comparable to or larger than the step height. For both suction and no-suction cases, an increase in the step height resulted in a sharp decrease in the initial heat-transfer rates behind the step. Downstream, however, the heat transfer gradually recovered back to less than or near attached-flow values. Mass suction from the step base area increased the local heat-transfer rates; however, this effect was relatively weak for the laminar flows considered. Even removal of the entire approaching boundary layer raised the post-step heat-transfer rates only about 10 percent above the flatplate values. Post-step pressure distributions were found to depend on the entrainment conditions at separation. In the case of the solid-faced step, a sharp pressure drop behind the step was followed by a very short plateau and relatively fast recompression. For the slotted-step connected to a large plenum but without suction, the pressure drop at the base was much smaller and the downstream recompression more gradual than that for solid-faced step.

Brown, R. D.↗
NASA NTRS1980

Interaction of oscillations of channel flow and flow separation at duct discontinuities

A two dimensional experiment was used to study the flow fluctuations in the separated region resulting from a wall slot step (convergent step). This geometry corresponds to the geometry present in a segmented solid rocket motor in the region of the ends of adjoining segments. A modulated tunnel flow of controlled oscillation frequency was used, and the effect on flow fluctuations in the separated region was examined by hot wire velocity measurements. The transfer function between free stream oscillations and separated flow fluctuations at the driven frequency was determined over a range of frequencies and main stream flow velocities. The transfer function exhibited a frequency dependence with maximum in the 10 - 25 Hz range, with the maximum occurring at higher frequency when the mean flow velocity was higher.

Price, E. W.↗
NASA NTRS1985

Time-dependent Navier-Stokes computations of separated flows over airfoils

The application of both a central-difference and an upwind implicit approximate factorization Navier-Stokes algorithm to highly separated flow is described. Using the thin-layer approximation, both algorithms are employed to solve the low Reynolds number laminar flow around a circular cylinder with periodic shedding. Results agree with experimental Strouhal numbers to within about 10 percent. A grid refinement study is conducted using the upwind code for both the thin-layer and complete Navier-Stokes approximations. The circular cylinder solution is shown to be highly dependent upon both grid density outward from the body and grid extent. Finally, the thin-layer central-difference code is used to predict the time-accurate unsteady flow about two stalled airfoils. The NACA 0012 airfoil turbulent solutions are periodic with Strouhal numbers of about 0.1; a strong vortex is periodically shed from the leading edge. The LS(1)-0417 airfoil turbulent solution shows a high frequency oscillatory trailing edge separation. The 20 degree NACA 0012 airfoil solution is massively separated, but shows no evidence of periodicity.

Rumsey, C. L.↗
NASA NTRS2001

Static and Wind Tunnel Aero-Performance Tests of NASA AST Separate Flow Nozzle Noise Reduction Configurations

This report presents the results of cold flow model tests to determine the static and wind tunnel performance of several NASA AST separate flow nozzle noise reduction configurations. The tests were conducted by Aero Systems Engineering, Inc., for NASA Glenn Research Center. The tests were performed in the Channels 14 and 6 static thrust stands and the Channel 10 transonic wind tunnel at the FluiDyne Aerodynamics Laboratory in Plymouth, Minnesota. Facility checkout tests were made using standard ASME long-radius metering nozzles. These tests demonstrated facility data accuracy at flow conditions similar to the model tests. Channel 14 static tests reported here consisted of 21 ASME nozzle facility checkout tests and 57 static model performance tests (including 22 at no charge). Fan nozzle pressure ratio varied from 1.4 to 2.0, and fan to core total pressure ratio varied from 1.0 to 1.19. Core to fan total temperature ratio was 1.0. Channel 10 wind tunnel tests consisted of 15 tests at Mach number 0.28 and 31 tests at Mach 0.8. The sting was checked out statically in Channel 6 before the wind tunnel tests. In the Channel 6 facility, 12 ASME nozzle data points were taken and 7 model data points were taken. In the wind tunnel, fan nozzle pressure ratio varied from 1.73 to 2.8, and fan to core total pressure ratio varied from 1.0 to 1.19. Core to fan total temperature ratio was 1.0. Test results include thrust coefficients, thrust vector angle, core and fan nozzle discharge coefficients, total pressure and temperature charging station profiles, and boat-tail static pressure distributions in the wind tunnel.

Mikkelsen, Kevin L.↗
NASA NTRS2011

USM3D Simulations of Saturn V Plume Induced Flow Separation

The NASA Constellation Program included the Ares V heavy lift cargo vehicle. During the design stage, engineers questioned if the Plume Induced Flow Separation (PIFS) that occurred along Saturn V rocket during moon missions at some flight conditions, would also plague the newly proposed rocket. Computational fluid dynamics (CFD) was offered as a tool for initiating the investigation of PIFS along the Ares V rocket. However, CFD best practice guidelines were not available for such an investigation. In an effort to establish a CFD process and define guidelines for Ares V powered simulations, the Saturn V vehicle was used because PIFS flight data existed. The ideal gas, computational flow solver USM3D was evaluated for its viability in computing PIFS along the Saturn V vehicle with F-1 engines firing. Solutions were computed at supersonic freestream conditions, zero degree angle of attack, zero degree sideslip, and at flight Reynolds numbers. The effects of solution sensitivity to grid refinement, turbulence models, and the engine boundary conditions on the predicted PIFS distance along the Saturn V were discussed and compared to flight data from the Apollo 11 mission AS-506.

Deere, Karen↗
NASA NTRS1974

Extension of leading-edge-suction analogy to wings with separated flow around the side edges at subsonic speeds

A method for determining the lift, drag, and pitching moment for wings which have separated flow at the leading and side edges with subsequently reattached flow downstream and inboard is presented. Limiting values of the contribution to lift of the side-edge reattached flow are determined for rectangular wings. The general behavior of this contribution is computed for rectangular, cropped-delta, cropped-diamond, and cropped-arrow wings. Comparisons of the results of the method and experiment indicate reasonably good correlation of the lift, drag, and pitching moment for a wide planform range. The agreement of the method with experiment was as good as, or better than, that obtained by other methods. The procedure is computerized and is available from COSMIC as NASA Langley computer program A0313.

Lamar, J. E.↗
NASA NTRS2000

Separate Flow Nozzle Test Status Meeting

NASA Glenn, in partnership with US industry, completed an exhaustive experimental study on jet noise reduction from separate flow nozzle exhaust systems. The study developed a data base on various bypass ratio nozzles, screened quietest configurations and acquired pertinent data for predicting the plume behavior and ultimately its corresponding jet noise. Several exhaust system configurations provided over 2.5 EPNdB jet noise reduction at take-off power. These data were disseminated to US aerospace industry in a conference hosted by NASA GRC whose proceedings are shown in this report.

Saiyed, Naseem H.↗
NASA NTRS1977

Studies of flow separation and stalling on one- and two-element airfoils at low speeds

Research has been conducted on the nature of airfoil behavior at pre- and post-separated angles of attack. Detailed wind tunnel studies have been made of boundary layer and wake fields for the GA(W)-1 airfoil, and the airfoil with a 0.3 chord Fowler flap. Experimental data are compared with theoretical predictions from a multi-element viscous flow computer program. Theoretical predictions are reasonably accurate for unseparated flows, but have serious errors when separation is present. Some recent techniques for modeling post-separated flow behavior are discussed in light of the present experiments.

Seetharam, H. C.↗
NASA NTRS1987

A global marching technique for the prediction of separated flows over arbitrary airfoils

The flow over arbitrary airfoils is analyzed using a boundary-layer-type solver developed for studying separated flows. The scheme includes extension to a general coordinate system and use of a more general zonal technique for solving the coupled equations. In order to be able to consider arbitrary geometries, second order accurate (in space) conservative differences are generated by considering the integral formulation of the governing equations in a general coordinate system. The general coordinate system is handled in as general a manner as possible to allow for the use of either analytically or numerically generated coordinate system. Different C type grids (orthogonal and nonorthogonal) were generated using different grid generation techniques to analyze the flow over arbitrary airfoils (J012, J025, NACA0012). A comparison with the experiment is demonstrated.

Halim, Ahmad A. M.↗