Search NASA⌕ Search

SEARCH · Search NASA

Results for “Skin Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Hot foil transducer skin friction sensor

The device utilizes foil transducers with only one edge exposed to the fluid flow. The surfaces are polished producing a foil transducer that does not generate turbulence while sufficiently thick to carry the required electrical current for high temperature fluid flow. The assembly utilizes a precut layered metal sandwich with attached electrodes eliminating a need for welding and individual sensor calibration.

Vranas, T.↗
NASA NTRS1983

Research on non-planar wall geometries for turbulence control and skin-friction reduction

Eight turbulence-control/drag-reduction concepts under study at NASA Langley Research Center are discussed. These concepts include: slot injection, ion wind, large-eddy breakup devices, riblets, relaminarization, convex curvature, passive porous walls, and rigid wavy walls. Of these concepts, passive porous walls and small wavelength wavy walls are found to increase drag. Riblets, slot injection, and large-eddy breakup devices reduce net turbulent drag, at least for some conditions. The ion wind, relaminarization, and convex curvature studies are still in the early stages and require further work to evaluate their applicability for drag reduction.

Hefner, J. N.↗
NASA NTRS1984

A method for measuring skin friction drag on a flat plate in contaminated gas flows

A technique for measuring friction drag in turbulent gas and gas/particle flows over flat plates is presented, and preliminary results are reported. A 0.25-in.-thick 72 x 6-in. Al plate is suspended by six horizontal support air bearings and four vertical alignment air bearings between fixed dummy plates and leading-edge and trailing-edge fairings in the 32-in.-high 48-in.-wide 11-ft-long test section of a closed-circuit atmospheric wind tunnel operating at 50-150 ft/sec. Particles of Fe and Al oxides of diameter 20-150 microns and density up to 0.3 lb particles per lb air are injected via a 6 x 0.167-in. nozzle; turbulence is induced by a roughened section of the leading-edge fairing; and friction drag is measured using a load-cell pressure transducer. Sample results are shown in a graph, demonstrating good agreement with theoretical drag calculations.

Oetting, R. B.↗
NASA NTRS1985

Fiber optic pressure sensors in skin-friction measurements

Fiber optic lever pressure sensors intended for use in a low speed wind tunnel environment were designed, constructed and tested for the measurement of normal and shear displacements associated with the pressures acting on a flat aluminum plate. On-site tests performed along with several static and dynamic measurements made have established that, with proper modifications and improvements, the design concepts are acceptable and can be utilized for their intended use. Several elastomers were investigated for use in sensors and for their incorporation into these sensors. Design and assembly techniques for probes and complete sensors were developed.

Kidwell, R.↗
NASA NTRS1986

Fiber optic pressure sensors in skin-friction measurements

A fiber optic lever sensing technique that can be used to measure normal pressure as well as shear stresses is discussed. This method uses three unequal fibers combining small size and good sensitivity. Static measurements appear to confirm the theoretical models predicted by geometrical optics and dynamic tests performed at frequencies up to 10 kHz indicate a flat response within this frequency range. These sensors are intended for use in a low speed wind tunnel environment.

Cuomo, F. W.↗
NASA NTRS1986

Mean flow in turbulent boundary layers disturbed to alter skin friction

A comparative evaluation is made of recent developments in methods for the reduction of boundary layer drag, encompassing longitudinal surface riblets, 'outer layer' devices, (OLDs) and longitudinal convex surface curvature. The boundary layer of a surface with a longitudinal concave curvature is also studied, to complement the convex case results. The net drag reductions achievable by both riblets and OLDs are noted to be a rather modest 10 percent. Boundary layers exhibit asymmetric response to streamwise surface curvatures, with the response being slower for the case of a concave than a convex curvature.

Bandyopadhyay, P. R.↗
NASA NTRS1991

Polymers And Riblets Reduce Hydrodynamic Skin Friction

Polymers injected into riblet grooves dramatically reduce polymer flow rate required for drag reduction. Polymer solution injected into valleys of grooves through array of holes or slots angled downstream to keep injected streams within grooves. Injection repeated some distance downstream because volumes of grooves finite and polymer becomes depleted as slowly pulled from groove by turbulence. Potentially useful for oil tankers as means of markedly reducing cost of fuel and used extensively on submarines, other ships, and other marine vehicles.

Bushnell, Dennis M.↗
NASA NTRS1991

Skin friction and heat transfer correlations for high-speed low-density flow past a flat plate

The independent and dependent variables associated with drag and heat transfer to a flat plate at zero incidence in high-speed, rarefied flow are analyzed anew to reflect the importance of kinetic effects occurring near the plate surface on energy and momentum transfer, rather than following arguments normally used to describe continuum, higher density flowfields. A new parameter, the wall Knudsen number Knx,w, based on an estimate of the mean free path length of molecules having just interacted with the surface of the plate, is introduced and used to correlate published drag and heat transfer data. The new parameter is shown to provide better correlation than either the viscous interaction parameter X or the widely-used slip parameter Voo for drag and heat transfer data over a wide range of Mach numbers, Reynolds numbers, and plate-to-freestream stagnation temperature ratios.

Woronowicz, Michael S.↗
NASA NTRS1990

The effect of a turbulent wake on the stagnation point. I - Skin friction results

The response of a boundary layer in the stagnation region of a two-dimensional body to fluctuations in the freestream is examined. The analysis is restricted to laminar incompressible flow. The assumed form of the velocity distribution at the edge of the boundary layer represents both a pulsation of the incoming flow, and an oscillation of the stagnation point streamline. Both features are essential in accurately representing the effect which freestream spatial and temporal nonuniformities have upon the unsteady boundary layer. Finally, a simple model is proposed which relates the characteristic parameters in a turbulent wake to the unsteady boundary-layer edge velocity. Numerical results are presented for both an arbitrary two-dimensional geometry and a circular cylinder.

Wilson, Dennis E.↗