Results for “Small Modular” — Page 12

NASA NTRS2017

Design and Benchmarking of a Network-In-the-Loop Simulation for Use in a Hardware-In-the-Loop System

Distributed engine control (DEC) systems alter aircraft engine design constraints be- cause of fundamental differences in the input and output communication between DEC and centralized control architectures. The change in the way communication is implemented may create new optimum engine-aircraft configurations. This paper continues the exploration of digital network communication by demonstrating a Network-In-the-Loop simulation at the NASA Glenn Research Center. This simulation incorporates a real-time network protocol, the Engine Area Distributed Interconnect Network Lite (EADIN Lite), with the Commercial Modular Aero-Propulsion System Simulation 40k (C-MAPSS40k) software. The objective of this study is to assess digital control network impact to the control system. Performance is evaluated relative to a truth model for large transient maneuvers and a typical flight profile for commercial aircraft. Results show that a decrease in network bandwidth from 250 Kbps (sampling all sensors every time step) to 40 Kbps, resulted in very small differences in control system performance.

Networked Systems↗

NASA NTRS2017

Design and Benchmarking of a Network-In-the-Loop Simulation for Use in a Hardware-In-the-Loop System

Distributed engine control (DEC) systems alter aircraft engine design constraints because of fundamental differences in the input and output communication between DEC and centralized control architectures. The change in the way communication is implemented may create new optimum engine-aircraft configurations. This paper continues the exploration of digital network communication by demonstrating a Network-In-the-Loop simulation at the NASA Glenn Research Center. This simulation incorporates a real-time network protocol, the Engine Area Distributed Interconnect Network Lite (EADIN Lite), with the Commercial Modular Aero-Propulsion System Simulation 40k (C-MAPSS40k) software. The objective of this study is to assess digital control network impact to the control system. Performance is evaluated relative to a truth model for large transient maneuvers and a typical flight profile for commercial aircraft. Results show that a decrease in network bandwidth from 250 Kbps (sampling all sensors every time step) to 40 Kbps, resulted in very small differences in control system performance.

Networked Systems↗

NASA NTRS1977

A low-cost system for reception and processing of line-scan data from LANDSAT and other sources

A low-cost transportable earth resources ground station was built in Canada and installed to operational status at Shoe Cove, Newfoundland. The system concepts developed for this station provide timely availability of data in both photographic and digital form. The system was designed with several objectives in mind: (1) to provide a system which could receive, store and process line-scan image data from a wide variety of satellites, most especially the LANDSAT and NOAA (VHRR) series, as well as aircraft scanner data, and data from future remote sensing and meteorological satellites; (2) the system has been designed to be operated by a small staff and to produce black and white images and computer-compatible tapes (CCT's) of all relevant data; (3) the system is compact in its physical design so that it is possible to configure it as a self-contained ground station, housed in a 3 x 12 meter trailer; (4) the system is designed to process all data at real-time rates or better and is designed in a modular fashion so that it can be easily upgraded to do further processing of the data, and/or to handle new satellites and sensors.

Sloan, D. S.↗

NASA NTRS2010

New Technology for Microfabrication and Testing of a Thermoelectric Device for Generating Mobile Electrical Power

We report the results of fabrication and testing of a thermoelectric power generation module. The module was fabricated using a new "flip-chip" module assembly technique that is scalable and modular. This technique results in a low value of contact resistivity ( < or = 10(exp 5) Ohms-sq cm). It can be used to leverage new advances in thin-film and nanostructured materials for the fabrication of new miniature thermoelectric devices. It may also enable monolithic integration of large devices or tandem arrays of devices on flexible or curved surfaces. Under mild testing, a power of 22 mW/sq cm was obtained from small (<100 K) temperature differences. At higher, more realistic temperature differences, approx.500 K, where the efficiency of these materials greatly improves, this power density would scale to between 0.5 and 1 Watt/cm2. These results highlight the excellent potential for the generation and scavenging of electrical power of practical and usable magnitude for remote applications using thermoelectric power generation technologies.

Prasad, Narashimha S.↗

NASA NTRS2004

Lightweight, Flexible, Thin, Integrated Solar-Power Packs

Lightweight, flexible, thin, one-piece, solar-power packs are undergoing development. Each power pack of this type is a complete, modular, integrated power-supply system comprising three power subsystems that, in conventional practice, have been constructed as separate units and connected to each other by wires. These power packs are amenable to a variety of uses: For example, they could be laminated to the tops of tents and other shelters to provide or augment power for portable electronic equipment in the field, and they could be used as power sources for such small portable electronic systems as radio transceivers (including data relays and cellular telephones), laptop computers, video camcorders, and Global Positioning System receivers.

Hanson, Robert R.↗

NASA NTRSDate not supplied

Habitable Working and Living Spaces in the Deep Space Science Vessel

The Deep Space Science Vessel (DSSV) is a conceptual design of a very large spacecraft intended as a mobile microgravity science platform. It represents an effort to conceptualize the systems and internal architectures needed to support a forty-eight-person crew for multi-year missions throughout the inner solar system and potentially beyond. The general arrangement of the DSSV is a modular spacecraft. Considering only the pressurized, habitable elements, the DSSV includes two large pressurized modules (Hab and Lab) docked together along with eight smaller node modules completing the habitable configuration. The Hab and Lab modules are docked side by side, with the longitudinal axes parallel to each other and a single docking port connecting them. A node module is docked to each dome on the Hab and Lab modules, such that the two small node modules on each end of the large Hab and Lab domes are docked both to each other and to the Hab and Lab. This creates a “racetrack” translation path on the interior. The other four node modules are docked at the center of the Hab and Lab modules, two on each side, creating another “racetrack” translation path perpendicular to the first one. The DSSV has a generally vertical orientation. Within the Hab and Lab modules the decks are perpendicular to the longitudinal axis. The node modules are oriented with their longitudinal axes perpendicular to those of the Hab and Lab modules, so the nodes have a horizontal internal orientation. Decks are numbered one through nine, with decks two and eight representing the “top” and “bottom” domes of the Hab and Lab modules. The Hab Module decks encompass the ship’s galley, crew quarters, waste, hygiene, portions of crew exercise, and group recreation. The Lab Module contains food production facilities, the life science lab, the ship’s infirmary, the physical science lab, and the maintenance and fabrication workshop. The Node Modules serve a number of different functions. The two Exercise Nodes are docked to deck five of both the Hab and Lab modules and contain most of the aerobic and resistive exercise devices. Also docked to deck five but on the opposite side of the Hab and Lab modules are the Observation Deck and Space Café. These two node modules provide social gathering space for small numbers of crew. The Mission Operations Node is on deck nine directly above the Galley and contains spacecraft monitoring and commanding capabilities. Docked to it is the EVA Operations Node, which contains suit maintenance and storage. (The airlock is a separate, external element docked to the EVA Operations Node.) The Subsystems Node is on deck one beneath the maintenance and fabrication workshop. Docked to it is the Stowage Node. This node does not house DSSV primary stowage, but is a staging point where stowage brought in from logistics modules can be sorted, unpacked, or repacked as needed prior to distribution to the appropriate sections of the spacecraft.

Deep Space Habitat↗

NASA NTRS2016

Launch Pad in a Box

NASA Kennedy Space Center (KSC) is developing a new deployable launch system capability to support a small class of launch vehicles for NASA and commercial space companies to test and launch their vehicles. The deployable launch pad concept was first demonstrated on a smaller scale at KSC in 2012 in support of NASA Johnson Space Center's Morpheus Lander Project. The main objective of the Morpheus Project was to test a prototype planetary lander as a vertical takeoff and landing test-bed for advanced spacecraft technologies using a hazard field that KSC had constructed at the Shuttle Landing Facility (SLF). A steel pad for launch or landing was constructed using a modular design that allowed it to be reconfigurable and expandable. A steel flame trench was designed as an optional module that could be easily inserted in place of any modular steel plate component. The concept of a transportable modular launch and landing pad may also be applicable to planetary surfaces where the effects of rocket exhaust plume on surface regolith is problematic for hardware on the surface that may either be damaged by direct impact of high speed dust particles, or impaired by the accumulation of dust (e.g., solar array panels and thermal radiators). During the Morpheus free flight campaign in 2013-14, KSC performed two studies related to rocket plume effects. One study compared four different thermal ablatives that were applied to the interior of a steel flame trench that KSC had designed and built. The second study monitored the erosion of a concrete landing pad following each landing of the Morpheus vehicle on the same pad located in the hazard field. All surfaces of a portable flame trench that could be directly exposed to hot gas during launch of the Morpheus vehicle were coated with four types of ablatives. All ablative products had been tested by NASA KSC and/or the manufacturer. The ablative thicknesses were measured periodically following the twelve Morpheus free flight tests. The thermal energy from the Morpheus rocket exhaust plume was only found to be sufficient to cause appreciable ablation of one of the four ablatives that were tested. The rocket exhaust plume did cause spalling of concrete during each descent and landing on a landing pad in the hazard field. The Extended Abstract ASE Earth and Space Conference April, 2016 - Orlando, FL concrete surface was laser scanned following each Morpheus landing, and the total volume of spalled concrete that eroded between the first and final landings of the Morpheus Project's test campaign was estimated. This paper will also describe a new deployable launch system (DLS) capability that is being developed at KSC and was publicly announced in May 2015 (KSC Partnerships, 2015). The DLS is a set of multi-user Ground Support Equipment that will be used to test and launch small class launch vehicles. The system is comprised of four main elements: the Launch Stand, the Flame Deflector, the Pad Apron and the KAMAG transporter. The system elements are designed to be deployed at launch or test sites within the KSC/CCAFS boundaries. The DLS is intended to be used together with the Fluid and Electrical System of the Universal Propellant Servicing Systems and Mobile Power Data and Communications Unit.

Ablatives Testing↗

NASA NTRS2016

Launch Pad in a Box

NASA Kennedy Space Center (KSC) is developing a new deployable launch system capability to support a small class of launch vehicles for NASA and commercial space companies to test and launch their vehicles. The deployable launch pad concept was first demonstrated on a smaller scale at KSC in 2012 in support of NASA Johnson Space Center's Morpheus Lander Project. The main objective of the Morpheus Project was to test a prototype planetary lander as a vertical takeoff and landing test-bed for advanced spacecraft technologies using a hazard field that KSC had constructed at the Shuttle Landing Facility (SLF). A steel pad for launch or landing was constructed using a modular design that allowed it to be reconfigurable and expandable. A steel flame trench was designed as an optional module that could be easily inserted in place of any modular steel plate component. The concept of a transportable modular launch and landing pad may also be applicable to planetary surfaces where the effects of rocket exhaust plume on surface regolith is problematic for hardware on the surface that may either be damaged by direct impact of high speed dust particles, or impaired by the accumulation of dust (e.g., solar array panels and thermal radiators). During the Morpheus free flight campaign in 2013-14, KSC performed two studies related to rocket plume effects. One study compared four different thermal ablatives that were applied to the interior of a steel flame trench that KSC had designed and built. The second study monitored the erosion of a concrete landing pad following each landing of the Morpheus vehicle on the same pad located in the hazard field. All surfaces of a portable flame trench that could be directly exposed to hot gas during launch of the Morpheus vehicle were coated with four types of ablatives. All ablative products had been tested by NASA KSC and/or the manufacturer. The ablative thicknesses were measured periodically following the twelve Morpheus free flight tests. The thermal energy from the Morpheus rocket exhaust plume was only found to be sufficient to cause appreciable ablation of one of the four ablatives that were tested. The rocket exhaust plume did cause spalling of concrete during each descent and landing on a landing pad in the hazard field. The Extended Abstract ASE Earth and Space Conference April, 2016 - Orlando, FL concrete surface was laser scanned following each Morpheus landing, and the total volume of spalled concrete that eroded between the first and final landings of the Morpheus Project's test campaign was estimated. This paper will also describe a new deployable launch system (DLS) capability that is being developed at KSC and was publicly announced in May 2015 (KSC Partnerships, 2015). The DLS is a set of multi-user Ground Support Equipment that will be used to test and launch small class launch vehicles. The system is comprised of four main elements: the Launch Stand, the Flame Deflector, the Pad Apron and the KAMAG transporter. The system elements are designed to be deployed at launch or test sites within the KSC/CCAFS boundaries. The DLS is intended to be used together with the Fluid and Electrical System of the Universal Propellant Servicing Systems and Mobile Power Data and Communications Unit

Mobile Launch Pad Development↗

NASA NTRS1989

Integrated aerodynamic-structural design of a transport wing

The integrated aerodynamic-structural design of a subsonic transport wing for minimum weight subject to required range is formulated and solved. The problem requires large computational resources, and two methods are used to alleviate the computational burden. First, a modular sensitivity method that permits the usage of black-box disciplinary software packages, is used to reduce the cost of sensitivity derivatives. In particular, it is shown that derivatives of the aeroelastic response and divergence speed can be calculated without the costly computation of derivatives of aerodynamic influence coefficient and structural stiffness matrices. A sequential approximate optimization is used to further reduce computational cost. The optimization procedure is shown to require a relatively small number of analysis and sensitivity calculations.

Grossman, B.↗

NASA NTRS2020

Aircraft Engine Run-To-Failure Data Set Under Real Flight Conditions

The generation of data-driven prognostics models requires the availability of datasets with run-to-failure trajectories. In order to contribute to the development of these methods, the dataset provides a new realistic dataset of run-to-failure trajectories for a small fleet of aircraft engines under realistic flight conditions. The damage propagation modelling used for the generation of this synthetic dataset builds on the modelling strategy from previous work [1] and incorporates two new levels of fidelity. First, it considers real flight conditions as recorded on board of a commercial jet [2]. Secondly, it extends the degradation modelling by relating the degradation process to the operation history. The dataset was generated with the Commercial Modular Aero-Propulsion System Simulation (C-MAPSS) dynamical model [3]. More details about the generation process can be found in [4].

CMAPSS↗

NASA NTRS1999

Thermal and Mechanical Microspacecraft Technologies for Deep Space Systems Program X2000 Future Deliveries

Thermal and mechanical technologies are an important part of the Deep Space Systems Technology (DSST) Program X2000 Future Deliveries (FD) microspacecraft. A wide range of future space missions are expected to utilize the technologies and the architecture developed by DSST FD. These technologies, besides being small in physical size, make the tiny spacecraft robust and flexible. The DSST FD architecture is designed to be highly reliable and suitable for a wide range of missions such as planetary landers/orbiters/flybys, earth orbiters, cometary flybys/landers/sample returns, etc. Two of the key ideas used in the development of thermal and mechanical technologies and architectures are: 1) to include several of the thermal and mechanical functions in any given single spacecraft element and 2) the architecture be modular so that it can easily be adapted to any of the future missions. One of the thermal architectures being explored for the DSST FD microspacecraft is the integrated thermal energy management of the complete spacecraft using a fluid loop. The robustness and the simplicity of the loop and the flexibility with which it can be integrated in the spacecraft have made it attractive for applications to DSST FD. Some of the thermal technologies to be developed as a part of this architecture are passive and active cooling loops, electrically variable emittance surfaces, miniature thermal switches, and specific high density electronic cooling technologies. In the mechanical area, multifunction architecture for the structural elements will be developed. The multifunction aspect is expected to substantially reduce the mass and volume of the spacecraft. Some of the technologies that will be developed are composite material panels incorporating electronics, cabling, and thermal elements in them. The paper describes the current state of the technologies and progress to be made in the thermal and mechanical technologies and approaches for the DSST Future Deliveries microspacecraft.

Birur, Gajanana C.↗

NASA NTRS2020

Kilopower Project: The KRUSTY Fission Power Experiment and Potential Missions

The Kilopower Project was initiated by NASA’s Space Technology Mission Directorate/Game Changing Development Program in fiscal year 2015 to demonstrate subsystem-level technology readiness of small space fission power in a relevant environment (Technology Readiness Level 5) for space science and human exploration power needs. The Kilopower Project centerpiece is the Kilowatt Reactor Using Stirling TechnologY (KRUSTY) test, which consists of the development and testing of a ground technology demonstrator of a 1-kW(electric)–class fission power system (FPS). The technologies to be developed and validated by KRUSTY are extensible to space FPSs from 1 to 10 kW(electric), which can enable modular surface FPSs for human exploration as well as higher-power future potential deep space science missions. The KRUSTY demonstration is cofunded by NASA and the U.S. Department of Energy National Nuclear Security Administration. The KRUSTY demonstration in the National Critical Experiment Research Center’s Device Assembly Facility was completed in the first quarter of 2018.

Space nuclear reactor↗

NASA NTRS1995

The NASA/MSFC Global Reference Atmospheric Model-1995 version (GRAM-95)

The latest version of the Global Reference Atmospheric Model (GRAM-95) is presented and discussed. GRAM-95 uses the new Global Upper Air Climatic Atlas (GUACA) CD-ROM data set, for 0- to 27-km altitudes. As with earlier versions, GRAM-95 provides complete geographical and altitude coverage for each month of the year. Individual years 1985 to 1991 and a period-of-record (1980 to 1991) can be simulated for the GUACA height range. GRAM-95 uses a specially developed data set, based on Middle Atmosphere Program (MAP) data, for the 20- to 120-km height range, and the NASA Marshall Engineering Thermosphere (MET) model for heights above 90 km. Fairing techniques assure a smooth transition in the overlap height ranges (20 to 27 km and 90 to 120 km). In addition to the traditional GRAM variables of pressure, density, temperature and wind components, GRAM-95 now includes water vapor and 11 other atmospheric constituents (O3, N2O, CO, CH4, CO2, N2, O2, O, A, He, and H). A new, variable-scale perturbation model provides both large-scale and small-scale deviations from mean values for the thermodynamic variables and horizontal and vertical wind components. The perturbation model includes new features that simulate intermittency (patchiness) in turbulence and small-scale perturbation fields. The density perturbations and density gradients (density shears) computed by the new model compare favorably in their statistical characteristics with observed density perturbations and density shears from 32 space shuttle reentry profiles. GRAM-95 provides considerable improvement in wind estimates from the new GUACA data set, compared to winds calculated from the geostrophic wind relations previously used in the 0- to 25-km height range. The GRAM-95 code has been put into a more modular form, easier to incorporate as subroutines in other programs (e.g., trajectory codes). A complete user's guide for running the program, plus sample input and output, is provided.

Justus, C. G.↗

NASA NTRS1981

Steam engine research for solar parabolic dish

The parabolic dish solar concentrator provides an opportunity to generate high grade energy in a modular system. Most of the capital is projected to be in the dish and its installation. Assurance of a high production demand of a standard dish could lead to dramatic cost reductions. High production volume in turn depends upon maximum application flexibility by providing energy output options, e.g., heat, electricity, chemicals and combinations thereof. Subsets of these options include energy storage and combustion assist. A steam engine design and experimental program is described which investigate the efficiency potential of a small 25 kW compound reheat cycle piston engine. An engine efficiency of 35 percent is estimated for a 700 C steam temperature from the solar receiver.

Demler, R. L.↗

NASA NTRS1990

Arcjet Nozzle Area Ratio Effects

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Curran, Francis M.↗

NASA NTRS1990

Arcjet nozzle area ratio effects

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Curran, Francis M.↗

NASA NTRS2018

A Rapid, Low-Cost Approach to Permanently Extend Life Beyond Earth

This presentation covers the value proposition and challenges of permanently extending life beyond Earth. It proposes that this can be most expeditiously accomplished by starting with a population of small Closed Ecological Systems (CES)s, each with several specie populations that enable each CES to persist indefinitely without the need to add resources, remove wastes, or require human intervention. Each CES is instrumented and controlled so that it can be remotely maintained, experiments performed, and data collected. Data from the entire population of CESs are managed in a cloud server database for analyses on how to improve the performance of each CES as well as formulate new CESs. The presentation discusses a modular, artificial-spacecraft prototype that could be used to fly CES modules in space under various gravity and radiation conditions to study changes in the CESs relative to their counterparts that remain on Earth as the control group. The presentation concludes with the next, low-cost steps for rapidly executing the approach described.

Dorais, Gregory A.↗

NASA NTRS1979

Small orbital transfer vehicle for shuttle operations

Small orbital transfer vehicles to place payloads in orbits with altitudes above those of the standard Shuttle operation are studied. Low energy earth orbits below those of the planned spinning solid upper stages are addressed. Tandem and clustered solids are considered along with controlled solids, monopropellant and bipropellant liquids, and staged solid/liquid combinations. The performance, airborne support equipment, and program costs for the selected candidate concepts are presented. The results show that the most economical way to deliver the low energy payloads is with a modular liquid bipropellant stage system for the large majority of the payloads. The remainder of the payloads would use the Shuttle with integral OMS and Scout from WTR for a few specialized payloads until the Shuttle is operational at WTR.

Sibila, A. I.↗