Results for “System Engineering and Integrations” — Page 12

NASA NTRSDate not supplied

Nuclear Thermal Propulsion (NTP) Fission Product and Source Term Analysis

Nuclear thermal propulsion (NTP) is an in-space propulsion technology that uses a nuclear reactor to directly heat a propellant to provide high thrust, at higher efficiencies than achievable with conventional chemical propulsion systems. Due to the ability of NTP rockets to efficiently provide high thrust, this technology has been proposed for long duration space missions such as crewed missions to Mars and beyond. A primary hurdle for NTP technology development is the demonstration of an integrated reactor engine system to verify its functionality and performance. This primarily requires the manufacture and testing of candidate reactor and engine technologies to demonstrate the proposed design enables desired performance and exhibits acceptable response under all known operation modes. A major component in this testing is fission product accumulation, since after operation radioactive isotopes can be produced and pose radiological dose concerns. This paper explains the background behind fission product analysis and the methodology used to evaluate current reactor designs and identify the amount of fission products present and their radiological impact. Results of multiple thrust level engines at different time periods are discussed and highlight the need for additional experimental testing to confirm fractional release levels of fission products out of the system. Benchmarking of models and future paths of analysis are also discussed.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

Development and Implementation of a Small Satellite Systems Engineering Webinar Series: A Collaboration Between United Nations Office for Outer Space Affairs and National Aeronautics and Space Administration

The United Nations Office for Outer Space Affairs (UNOOSA) in collaboration with the National Aeronautics and Space Administration (NASA) established a webinar series on NASA systems engineering standards and practices for the purpose of sharing knowledge in this area through UNOOSA’s “Access to Space for All” which provides free and accessible educational content. Through NASA’s Small Spacecraft Systems Virtual Institute (S3VI), the four-part series was designed to cover basic systems engineering and project management skills that are fundamental for planning, developing, and implementing an experiment or a space project, and that serve as critical knowledge for those engaged in space activities, whether as a designer, builder, or manager of space infrastructure and services. This first series of webinars was convened over the course of November 2023 through February 2024. The webinar series was segmented into four one and a half hour webinars which covered topics related to the Fundamentals of Systems Engineering, Requirements and Systems Engineering, System Assembly, Integration and Test, and Spacecraft Handling, as well as an Introduction to the Small Spacecraft Systems Virtual Institute (S3VI). The agendas for the first three webinars focused on addressing a number of questions relevant to a particular topic. Examples of these questions include: What is systems engineering and what does a systems engineer do? Why does NASA use systems engineering? How do you define requirements for a small spacecraft mission? Why are requirements important to space missions? How are trade studies used to determine parts selection and why are they important? The final webinar of the first series provided interactive discussions and demonstrations of the S3VI tools; shared information on additional webinar opportunities offered by the S3VI; and reviewed databases curated by the S3VI that include the Small Satellite Reliability Initiative (SSRI) Knowledge Base Tool, Mission Design Tools, Small Spacecraft Information Search, and the State-of-the-Art (SoA) Small Spacecraft Report. Future webinar series will be conducted with topics are to be determined. The presenter will discuss details related to the first webinar series and future plans for additional series.

systems engineering↗

NASA NTRS2008

Constellation Program Life-cycle Cost Analysis Model (LCAM)

The Constellation Program (CxP) is NASA's effort to replace the Space Shuttle, return humans to the moon, and prepare for a human mission to Mars. The major elements of the Constellation Lunar sortie design reference mission architecture are shown. Unlike the Apollo Program of the 1960's, affordability is a major concern of United States policy makers and NASA management. To measure Constellation affordability, a total ownership cost life-cycle parametric cost estimating capability is required. This capability is being developed by the Constellation Systems Engineering and Integration (SE&I) Directorate, and is called the Lifecycle Cost Analysis Model (LCAM). The requirements for LCAM are based on the need to have a parametric estimating capability in order to do top-level program analysis, evaluate design alternatives, and explore options for future systems. By estimating the total cost of ownership within the context of the planned Constellation budget, LCAM can provide Program and NASA management with the cost data necessary to identify the most affordable alternatives. LCAM is also a key component of the Integrated Program Model (IPM), an SE&I developed capability that combines parametric sizing tools with cost, schedule, and risk models to perform program analysis. LCAM is used in the generation of cost estimates for system level trades and analyses. It draws upon the legacy of previous architecture level cost models, such as the Exploration Systems Mission Directorate (ESMD) Architecture Cost Model (ARCOM) developed for Simulation Based Acquisition (SBA), and ATLAS. LCAM is used to support requirements and design trade studies by calculating changes in cost relative to a baseline option cost. Estimated costs are generally low fidelity to accommodate available input data and available cost estimating relationships (CERs). LCAM is capable of interfacing with the Integrated Program Model to provide the cost estimating capability for that suite of tools.

Prince, Andy↗

NASA NTRS2015

IAF 15 Draft Paper

With the International Space Station Program transition from assembly to utilization, focus has been placed on the optimization of essential resources. This includes resources both resupplied from the ground and also resources produced by the ISS. In an effort to improve the use of two of these, the ISS Engineering teams, led by the ISS Program Systems Engineering and Integration Office, undertook an effort to modify the techniques use to perform several key on-orbit events. The primary purposes of this endeavor was to make the ISS more efficient in the use of the Russian-supplied fuel for the propulsive attitude control system and also to minimize the impacts to available ISS power due to the positioning of the ISS solar arrays. Because the ISS solar arrays are sensitive to several factors that are present when propulsive attitude control is used, they must be operated in a manner to protect them from damage. This results in periods of time where the arrays must be positioned, rather than autonomously tracking the sun, resulting in negative impacts to power generated by the solar arrays and consumed by both the ISS core systems and payload customers. A reduction in the number and extent of the events each year that require the ISS to use propulsive attitude control simultaneously accomplishes both these goals. Each instance where the ISS solar arrays normal sun tracking mode must be interrupted represent a need for some level of powerdown of equipment. As the magnitude of payload power requirements increases, and the efficiency of the ISS solar arrays decreases, these powerdowns caused by array positioning, will likely become more significant and could begin to negatively impact the payload operations. Through efforts such as this, the total number of events each year that require positioning of the arrays to unfavorable positions for power generation, in order to protect them against other constraints, are reduced. Optimization of propulsive events and transitioning some of them to non-propulsive CMG control significantly reduces propellant usage on the ISS leading to the reduction of the propellant delivery requirement. This results in move available upmass that can be used for delivering critical dry cargo, additional water, air, crew supplies and science experiments.

Menkin, Evgeny↗

NASA NTRS1984

Definition of ground test for Large Space Structure (LSS) control verification

An overview for the definition of a ground test for the verification of Large Space Structure (LSS) control is given. The definition contains information on the description of the LSS ground verification experiment, the project management scheme, the design, development, fabrication and checkout of the subsystems, the systems engineering and integration, the hardware subsystems, the software, and a summary which includes future LSS ground test plans. Upon completion of these items, NASA/Marshall Space Flight Center will have an LSS ground test facility which will provide sufficient data on dynamics and control verification of LSS so that LSS flight system operations can be reasonably ensured.

Waites, H. B.↗

NASA NTRS2003

X-43C Plans and Status

X-43C Project is a hypersonic flight demonstration being executed as a collaboration between the National Aeronautics and Space Administration (NASA) and the United States Air Force (USAF). X-43C will expand the hypersonic flight envelope for air breathing engines beyond the history making efforts of the Hyper-X Program (X-43A). X-43C will demonstrate sustained accelerating flight during three flight tests of expendable X-43C Demonstrator Vehicles (DVs). The approximately 16-foot long X-43C DV will be boosted to the starting test conditions, separate from the booster, and accelerate from Mach 5 to Mach 7 under its own power and autonomous control. The DVs are to be powered by a liquid hydrocarbon-fueled, fuel-cooled, dual-mode, airframe integrated scramjet engine system developed under the USAF HyTech Program. The Project is managed by NASA Langley Research Center as part of NASA s Next Generation Launch Technology Program. Flight tests will be conducted by NASA Dryden Flight Research Center over water off the coast of California in the Pacific Test Range. The NASA/USAF/industry project is a natural extension of the Hyper-X Program (X-43A), which will demonstrate short duration (~ 10 seconds) gaseous hydrogen-fueled scramjet powered flight at Mach 7 and Mach 10 using a heavyweight, largely heat sink construction, experimental engine. The X-43C Project will demonstrate sustained accelerating flight from Mach 5 to Mach 7 (~ 4 minutes) using a flight-weight, fuel-cooled, scramjet engine powered by much denser liquid hydrocarbon fuel. The X-43C DV design flows from integrating USAF HyTech developed engine technologies with a NASA Air Breathing Launch Vehicle accelerator-class configuration and Hyper-X heritage vehicle systems designs. This paper describes the X-43C Project and provides background for NASA s current hypersonic flight demonstration efforts.

Moses, Paul L.↗

NASA NTRS2000

Integrated Vehicle Health Management for the 2nd Generation RLV Program

This viewgraph presentation gives an overview of the Integrated Vehicle Health Management (IVHM) for Second Generation Reusable Launch Vehicle (RLV) program, including details on the second and third RLV programs, IVHM activity at Kennedy Space Center, the NASA X-37 IVHM flight experiment, propulsion and power IVHM, IVHM technologies at the Jet Propulsion Laboratory, structures IVHM for third generation RLVs, and IVHM systems engineering and integration.

Merriam, Marshal L.↗

NASA NTRS1994

Renaissance architecture for Ground Data Systems

The Mission Operations and Data Systems Directorate (MO&DSD) has embarked on a new approach for developing and operating Ground Data Systems (GDS) for flight mission support. This approach is driven by the goals of minimizing cost and maximizing customer satisfaction. Achievement of these goals is realized through the use of a standard set of capabilities which can be modified to meet specific user needs. This approach, which is called the Renaissance architecture, stresses the engineering of integrated systems, based upon workstation/local area network (LAN)/fileserver technology and reusable hardware and software components called 'building blocks.' These building blocks are integrated with mission specific capabilities to build the GDS for each individual mission. The building block approach is key to the reduction of development costs and schedules. Also, the Renaissance approach allows the integration of GDS functions that were previously provided via separate multi-mission facilities. With the Renaissance architecture, the GDS can be developed by the MO&DSD or all, or part, of the GDS can be operated by the user at their facility. Flexibility in operation configuration allows both selection of a cost-effective operations approach and the capability for customizing operations to user needs. Thus the focus of the MO&DSD is shifted from operating systems that we have built to building systems and, optionally, operations as separate services. Renaissance is actually a continuous process. Both the building blocks and the system architecture will evolve as user needs and technology change. Providing GDS on a per user basis enables this continuous refinement of the development process and product and allows the MO&DSD to remain a customer-focused organization. This paper will present the activities and results of the MO&DSD initial efforts toward the establishment of the Renaissance approach for the development of GDS, with a particular focus on both the technical and process implications posed by Renaissance to the MO&DSD.

Perkins, Dorothy C.↗

NASA NTRS2003

X-43C Flight Demonstrator Project Overview

The X-43C Flight Demonstrator Project is a joint NASA-USAF hypersonic propulsion technology flight demonstration project that will expand the hypersonic flight envelope for air-breathing engines. The Project will demonstrate sustained accelerating flight through three flights of expendable X-43C Demonstrator Vehicles (DVs). The approximately 16-foot long X-43C DV will be boosted to the starting test conditions, separate from the booster, and accelerate from Mach 5 to Mach 7 under its own power and autonomous control. The DVs will be powered by a liquid hydrocarbon-fueled, fuel-cooled, dual-mode, airframe integrated scramjet engine system developed under the USAF HyTech Program. The Project is managed by NASA Langley Research Center as part of NASA's Next Generation Launch Technology Program. Flight tests will be conducted by NASA Dryden Flight Research Center off the coast of California over water in the Pacific Test Range. The NASA/USAF/industry project is a natural extension of the Hyper-X Program (X-43A), which will demonstrate short duration (approximately 10 seconds) gaseous hydrogen-fueled scramjet powered flight at Mach 7 and Mach 10 using a heavy-weight, largely heat sink construction, experimental engine. The X-43C Project will demonstrate sustained accelerating flight from Mach 5 to Mach 7 (approximately 4 minutes) using a flight-weight, fuel-cooled, scramjet engine powered by much denser liquid hydrocarbon fuel. The X-43C DV design flows from integrating USAF HyTech developed engine technologies with a NASA Air-Breathing Launch Vehicle accelerator-class configuration and Hyper-X heritage vehicle systems designs. This paper describes the X-43C Project and provides the background for NASA's current hypersonic flight demonstration efforts.

Moses, Paul L.↗

NASA NTRS1986

CELSS experiment model and design concept of gas recycle system

In order to prolong the duration of manned missions around the Earth and to expand the human existing region from the Earth to other planets such as a Lunar Base or a manned Mars flight mission, the controlled ecological life support system (CELSS) becomes an essential factor of the future technology to be developed through utilization of space station. The preliminary system engineering and integration efforts regarding CELSS have been carried out by the Japanese CELSS concept study group for clarifying the feasibility of hardware development for Space station experiments and for getting the time phased mission sets after FY 1992. The results of these studies are briefly summarized and the design and utilization methods of a Gas Recycle System for CELSS experiments are discussed.

Nitta, K.↗

NASA NTRS2010

The History and Promise of Combined Cycle Engines for Access to Space Applications

For the summer of 2010, I have been working in the Aerodynamics and Propulsion Branch at NASA Dryden Flight Research Center studying combined-cycle engines, a high speed propulsion concept. Combined cycle engines integrate multiple propulsion systems into a single engine capable of running in multiple modes. These different modes allow the engine to be extremely versatile and efficient in varied flight conditions. The two most common types of combined cycle engines are Rocket-Based Combined Cycle (RBCC) and Turbine Based Combined Cycle (TBCC). The RBCC essentially combines a rocket and ramjet engine, while the TBCC integrates a turbojet and ramjet1. These two engines are able to switch between different propulsion modes to achieve maximum performance. Extensive conceptual and ground test studies of RBCC engines have been undertaken; however, an RBCC engine has never, to my knowledge, been demonstrated in flight. RBCC engines are of particular interest because they could potentially power a reusable launch vehicle (RLV) into space. The TBCC has been flight tested and shown to be effective at reaching supersonic speeds, most notably in the SR-71 Blackbird2.

Clark, Casie↗

NASA NTRSDate not supplied

Logistics Reduction Advancements and Future Plans for NASA's Exploration Missions

Management of logistics on exploration missions includes both looking for ways to minimize the quantities, mass and volume of various consumables, supplies, spares, and equipment as well as ways to minimize the crew time needed for locating and handling those items. Also included are ways to minimize the waste, handling, and resultant products from the processes of maintaining a crew on these missions. The Logistics Reduction project encompasses technologies for management of waste, trash, autonomous logistics, and clothing. This paper provides a status of work from 2023 in these areas including recent accomplishments and challenges encountered. Future objectives and plans for 2024 will also be covered along with the work currently in progress. Specifically, the paper will cover technologies in waste management, namely, the Universal Waste Management System (UWMS) or exploration toilet and work on an alternative waste collection container, the Alternate Fecal Canister. Trash management technologies work on the Trash Compaction Processing System (TCPS) and Trash to Gas (TtG) is summarized with progress to date as well as information on how Jettison as an option is related. Progress and summary of recent accomplishment on the RFID (Radio Frequency ID) Enabled Autonomous Logistics Management (REALM) and the Autonomous Logistics (AL) technologies is detailed. Advanced Clothing System (ACS) and work in the area of Systems Engineering and Integration (SE&I) is also included. Status of the technologies, accomplishments and how the focus areas inform program decisions will be addressed.

Toilet↗

NASA NTRS2024

Logistics Reduction Advancements and Future Plans for NASA's Exploration Missions

Management of logistics on exploration missions includes both looking for ways to minimize the quantities, mass and volume of various consumables, supplies, spares, and equipment as well as ways to minimize the crew time needed for locating and handling those items. Also included are ways to minimize the waste, handling, and resultant products from the processes of maintaining a crew on these missions. The Logistics Reduction project encompasses technologies for management of waste, trash, autonomous logistics, and clothing. This paper provides a status of work from 2023 in these areas including recent accomplishments and challenges encountered. Future objectives and plans for 2024 will also be covered along with the work currently in progress. Specifically, the paper will cover technologies in waste management, namely, the Universal Waste Management System (UWMS) or exploration toilet and work on an alternative waste collection container, the Alternate Fecal Canister. Trash management technologies work on the Trash Compaction Processing System (TCPS) and Trash to Gas (TtG) is summarized with progress to date as well as information on how Jettison as an option is related. Progress and summary of recent accomplishment on the RFID (Radio Frequency ID) Enabled Autonomous Logistics Management (REALM) and the Autonomous Logistics (AL) technologies is detailed. Advanced Clothing System (ACS) and work in the area of Systems Engineering and Integration (SE&I) is also included. Status of the technologies, accomplishments and how the focus areas inform program decisions will be addressed.

Toilet↗

NASA NTRSDate not supplied

Logistics Reduction Advancements and Future Plans for NASA's Exploration Missions

Management of logistics on exploration missions includes both looking for ways to minimize the quantities, mass and volume of various consumables, supplies, spares, and equipment as well as ways to minimize the crew time needed for locating and handling those items. Also included are ways to minimize the waste, handling, and resultant products from the processes of maintaining a crew on these missions. The Logistics Reduction project encompasses technologies for management of waste, trash, autonomous logistics, and clothing. This paper provides a status of work from 2023 in these areas including recent accomplishments and challenges encountered. Future objectives and plans for 2024 will also be covered along with the work currently in progress. Specifically, the paper will cover technologies in waste management, namely, the Universal Waste Management System (UWMS) or exploration toilet and work on an alternative waste collection container, the Alternate Fecal Canister. Trash management technologies work on the Trash Compaction Processing System (TCPS) and Trash to Gas (TtG) is summarized with progress to date as well as information on how Jettison as an option is related. Progress and summary of recent accomplishment on the RFID (Radio Frequency ID) Enabled Autonomous Logistics Management (REALM) and the Autonomous Logistics (AL) technologies is detailed. Advanced Clothing System (ACS) and work in the area of Systems Engineering and Integration (SE&I) is also included. Status of the technologies, accomplishments and how the focus areas inform program decisions will be addressed.

Toilet↗

NASA NTRS2024

Flight Certification Approach for NASA's Space Launch System

NASA’s Space Launch System (SLS) vehicle was successfully launched on November 16, 2022, initiating the Artemis I mission to send the uncrewed Orion spacecraft to the Moon and further into space than any human-rated spacecraft had previously flown. Flight certification of the launch vehicle was part of the systems engineering and integration (SE&I) effort conducted by NASA to successfully certify the mission and begin a new era of human space exploration of the Moon and eventually Mars. This paper describes the SLS Program flight certification approach including the organization, processes, and reporting. This approach used traditional NASA SE&I milestone reviews and lessons learned from the Space Shuttle Program, as well as unique methods to certify the complex system, procedures, and personnel readiness. The approach utilized by the SLS Program to conduct flight certification for the Artemis I mission can be extended to address flight certification for other complex programs.

flight certification↗

NASA NTRS2008

Designing the Ares I Crew Launch Vehicle Upper Stage Element and Integrating the Stack at NASA's Marshall Space Flight Center

Fielding an integrated launch vehicle system entails many challenges, not the least of which is the fact that it has been over 30 years since the United States has developed a human-rated vehicle - the venerable Space Shuttle. Over time, whole generations of rocket scientists have passed through the aerospace community without the opportunity to perform such exacting, demanding, and rewarding work. However, with almost 50 years of experience leading the design, development, and end-to-end systems engineering and integration of complex launch vehicles, the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center offers the in-house talent - both junior- and senior-level personnel - to shape a new national asset to meet the requirements for safe, reliable, and affordable space exploration solutions. The technical personnel are housed primarily in Marshall's Engineering Directorate and are matrixed into the programs and projects that reside at the rocket center. Fortunately, many Apollo-era and Shuttle engineers, as well as those who gained valuable hands-on experience in the 1990s by conducting technology demonstrator projects such as the Delta-Clipper Experimental Advanced, X-33, X-34, and X-37, as well as the short-lived Orbital Space Plane, work closely with industry partners to advance the nation's strategic capability for human access to space. The Ares Projects Office, resident at Marshall, is managing the design and development of America's new space fleet, including the Ares I, which will loft the Orion crew capsule for its first test flight in the 2013 timeframe, as well as the heavy-lift Ares V, which will round out the capability to leave low-Earth orbit once again, when it delivers the Altair lunar lander to orbit late next decade. This paper provides information about the approach to integrating the Ares I stack and designing the upper stage in house, using unique facilities and an expert workforce to revitalize the nation's space exploration resources.

Otte, Neil E.↗

NASA NTRS2017

Practical Application of Sociology in Systems Engineering

Systems engineering involves both the integration of the system and the integration of the disciplines which develop and operate the system. Integrating the disciplines is a sociological effort to bring together different groups, who often have different terminology, to achieve a common goal, the system. The focus for the systems engineer is information flow through the organization, between the disciplines, to ensure the system is developed and operated will all relevant information informing system decisions. The practical application of the sociology in systems engineering brings in various organizational development concepts including the principles of planned renegotiation and the application of principles to address information barriers created by organizational culture. Concepts such as specification of ignorance, consistent terminology, opportunity structures, role-sets, and the reclama (reconsideration) process are all important sociological approaches that help address the organizational social structure (culture). In bringing the disciplines together, the systems engineer must also be wary of social ambivalence, social anomie, social dysfunction, and insider-outsider behavior. Unintended consequences can result when these social issues are present. These issues can occur when localized subcultures shift from the overarching organizational culture, or when the organizational culture prevents achievement of system goals. These sociological principles provide the systems engineer with key approaches to manage the information flow through the organization as the disciplines are integrated and share their information and provides key sociological barriers to information flow through the organization. This paper will discuss the practical application of sociological principles to systems engineering.

Watson, Michael D.↗

NASA NTRS1994

A versatile nondestructive evaluation imaging workstation

Ultrasonic C-scan and eddy current imaging systems are of the pointwise type evaluation systems that rely on a mechanical scanner to physically maneuver a probe relative to the specimen point by point in order to acquire data and generate images. Since the ultrasonic C-scan and eddy current imaging systems are based on the same mechanical scanning mechanisms, the two systems can be combined using the same PC platform with a common mechanical manipulation subsystem and integrated data acquisition software. Based on this concept, we have developed an IBM PC-based combined ultrasonic C-scan and eddy current imaging system. The system is modularized and provides capacity for future hardware and software expansions. Advantages associated with the combined system are: (1) eliminated duplication of the computer and mechanical hardware, (2) unified data acquisition, processing and storage software, (3) reduced setup time for repetitious ultrasonic and eddy current scans, and (4) improved system efficiency. The concept can be adapted to many engineering systems by integrating related PC-based instruments into one multipurpose workstation such as dispensing, machining, packaging, sorting, and other industrial applications.

Chern, E. James↗