Search NASA⌕ Search

SEARCH · Search NASA

Results for “THERMAL EXPANSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Thermal properties of field-assisted-sintered SiCN–Y 2 O 3 composites

Polymer-derived amorphous SiCN has excellent high-temperature stability and properties. To reduce the shrinkage during pyrolysis and to improve the high-temperature oxidation resistance, Y 2 O 3 was added as a filler. In this study, polymer-derived SiCN–Y 2 O 3 composites were fabricated by mixing a polymeric precursor of SiCN with Y 2 O 3 submicron powders in different ratios. The mixtures were cross-linked and pyrolyzed in argon. SiCN–Y 2 O 3 composites were processed using field-assisted sintering technology at 1350°C for 5 min under vacuum. Dense SiCN–Y 2 O 3 composite pellets were successfully made with relative density higher than 98% and homogeneous microstructure. Due to low temperature and short time of the heat-treatment, the grain growth of Y 2 O 3 was substantially inhibited. The Y 2 O 3 grain size was ~1 μm after sintering. The composites’ heat capacity, thermal diffusivity, and thermal expansion coefficients were characterized as a function of temperature. The thermal conductivity of the composites ceramics decreased as the amount of amorphous SiCN increased and the coefficient of thermal expansion (CTE) of the composites increased with Y 2 O 3 content. However, the thermal conductivity and CTE did not follow the rule of mixture. This is likely due to the partial oxidation of SiCN and the resultant impurity phases such as Y 2 SiO 5 , Y 2 Si 2 O 7 , and Y 4.67 (SiO 4 ) 3 O.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Numerical and Experimental Study of an Aircraft Igniter Plasma Jet Discharge

The spark discharge of an aircraft plasma jet igniter is studied using high-fidelity numerical simulations and X-ray radiography measurements. The target problem here features the thermal expansion of hot gas introduced by the electric spark within a confined igniter cavity, which eventually evolves into a pulsed jet of a high-temperature kernel. A comprehensive set of models adapted from existing strategies for internal combustion engine spark plug discharge is extended to the target problem, including the modeling of energy deposition, plasma reactions, thermodynamic properties, and heat losses. A series of validation and parameter studies are performed and presented. The kernel size is found to be sensitive to heat losses arising from radiation and hot gas remained within the discharge cavity, rather than heat conduction to the wall in the discharge cavity. Depending on the enforced shape of the post-breakdown electric arc, the spark kernel can be off-centered, tilted, and considerably asymmetric. These features have been previously not considered when studying such igniter configurations and may have a first-order impact on the ignition process. Provided a proper setup of the heat loss models and electric arc shape, the numerical results are quantitatively comparable to the experimental results in terms of the kernel size, shape, and velocity throughout different stages after the spark discharge.

Tang, Yihao↗
DOE OSTI2025

Thermophysical Properties of Ti3SiC2 MAX Phase Composites with SiC Reinforcement

In the present work, dense (∼100%) Ti 3 SiC 2 composites (TSC) are processed along with 20 vol% of SiC reinforcement (TSC20) via spark plasma sintering at 1400°C, 40 MPa, 15 min, and dynamic vacuum environment. Thermal expansion of both the composites increases from RT to 1273 K and linear fitting of data yields coefficient of thermal expansion (CTE) of 9.4 × 10 −6 K −1 for TSC which decreases to 8.3 × 10 −6 K −1 for TSC20. With increase in temperature from RT to 773 K, specific heat for both TSC and TSC20 composites is observed to increase from 598-850 J.kg −1 .K −1 , whereas thermal diffusivity and thermal conductivity values decrease with testing temperature. SiC reinforcement in Ti 3 SiC 2 resulted in improved thermal diffusivity from 12.7 to 18.7 mm 2 .s −1 and thermal conductivity from ∼57 to ∼79 W.m −1 .K −1 at RT. However, with increase in temperature (773 K), thermal diffusivity and conductivity decrease, and values get closer for both TSC and TSC20 composites. Further extrapolation of thermal conductivity data showed cross-over at ∼973 K due to domination of phonon-phonon scattering and thus lower values of thermal conductivity for TSC20 than TSC. Therefore, reduced CTE and higher thermal conductivity of TSC20 make it a viable choice for applications in high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancing the accuracy and generality of the Debye–Grüneisen Model: Optimizing the volume dependence for accurate predictions across varied compositions

In this work, we have introduced an optimized Debye-Grüneisen model that revolutionizes the determination of the Debye temperature and Grüneisen parameters. Unlike conventional methods, our model requires only the 0 K energy volume data for a material as input, eliminating the need to determine the bulk modulus and its pressure derivative, which often pose challenges due to numerical uncertainties. This unique feature sets our model apart from existing approaches and streamlines the process, enabling accurate predictions of thermal expansion behavior across various materials. To demonstrate its effectiveness, we showcase its excellent agreement with measured coefficients of thermal expansion (CTE) for the nickel-cobalt-chromium-aluminum-yttrium (Ni-Co-Cr-Al-Y) bond-coating system. Additionally, we apply our approach by conducting a high-throughput search for potential bond-coating materials among 90,000 compositions within the aluminum-cobalt-chromium-iron-nickel (Al-Co-Cr-Fe-Ni) system. From this extensive search, four compositions are synthesized, and the measured CTE values agree very well with theoretical predictions, hence validating our approach. In conclusion, the current optimized Debye-Grüneisen model combined with Density Functional Theory (DFT)-based thermodynamic database enables reliable and efficient high-throughput calculations of CTE of of a material without expensive phonon calculations.

Bond coating materials↗
DOE OSTI2023

Finite temperature properties of uranium mononitride

Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys, such as high melting temperature and high uranium density, and thermal conductivity, respectively. A better understanding of UN behavior at operating temperatures can be obtained from finite temperature data, such as elastic properties. To get this information, ab initio molecular dynamics (AIMD) simulations were performed at five different temperatures using constant volume (NVT) and constant pressure (NPT) ensembles. Initially, the performance of PBE functional in reproducing experimental crystallographic properties and magnetic ordering is assessed. The finite temperature phonon dispersions are calculated using NVT simulation results, which show a softening of the phonon modes with increasing temperature. The NPT results are used to obtain the thermal expansion of UN and finite temperature electronic properties. The calculated thermal expansion is compared with our measurements using neutron diffraction. Additionally, the temperature dependent elastic properties of UN are evaluated using the strain-stress method in AIMD simulations, indicating that UN becomes softer and more compressible with increasing temperature. Also, the calculated Young’s modulus slope is in very good agreement with the experiment. The finite temperature heat capacity and electronic thermal conductivity are calculated from AIMD simulations, which are in better agreement with the experiment than the heat capacity and thermal conductivity calculated using the structures relaxed at 0K. Finally, the thermal diffusivity from AIMD has opposite temperature dependence compared to experimental results, which we argued comes from the underestimated electronic thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Spatially inhomogeneous superconductivity in UTe 2

The newly discovered superconductor UTe 2 is a strong contender for a topological spin-triplet state wherein a multicomponent order parameter arises from two nearly degenerate superconducting states. A key issue is whether both of these states intrinsically exist at ambient pressure. Through thermal expansion and calorimetry, we show that UTe 2 at ambient conditions exhibits two detectable transitions only in some samples, and the size of the thermal expansion jump at each transition varies when the measurement is performed in different regions of the sample. This result indicates that the two transitions arise from two spatially separated regions that are inhomogeneously mixed throughout the volume of the sample, each with a discrete superconducting transition temperature (T c ). Notably, samples with higher T c only show a single transition at ambient pressure. Above 0.3 GPa, however, two transitions are invariably observed in ac calorimetry. Our results not only point to a nearly vertical line (constant pressure) in the pressure-temperature phase diagram but also provide a consistent scenario for the sample dependence of UTe 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Low temperature tetragonal polymorph of CaZrF 6

A new tetragonal polymorph of CaZrF 6 can be prepared by high energy ball milling of a CaF 2 /ZrF 4 mixture, followed by heat treatment at 325 °C. This polymorph is thermodynamically stable with respect to the well-known cubic form at low temperatures. However, it readily transforms to the cubic form on heating above ~400 °C. The tetragonal (β) CaZrF 6 is not isostructural with any previously known alkaline earth AZrF 6 phase. Unlike the cubic form, which shows strong negative thermal expansion over a wide temperature range, the tetragonal form displays positive thermal expansion in all directions (100–400 K: α l ~ +17 × 10 –6 K –1 and +13 × 10 –6 K –1 along the a- and c-axes, respectively).

36 MATERIALS SCIENCE↗
DOE OSTI2024

HYDRODYNAMIC TESTING OF ZIRCALOY TO STEEL HUB COUPLINGS FOR USE IN ADVANCED TEST REACTOR I-LOOP TUBE

The ATR I-positions' isolation from the flux trap region provides an opportunity for a test facility that could create conditions representative of commercial light water reactors. Such a facility requires piping couplings and joints that withstand extreme thermal and pressure cycling. Also, transitioning from steel to zircaloy piping inside the reactor vessel allows the neutronic properties of zircaloy to be leveraged while using cost-effective stainless steel outside of the core. Grayloc-style hub couplings will act as transition points between stainless steel piping and zircaloy piping inside the reactor vessel. These couplings have not been sufficiently tested for leakage where there is a transition between materials. This transition is a concern because the thermal expansion coefficients of the materials differ. Seal integrity between the two components may be greatly affected by thermal expansion at the connection. Thus, the effect of thermal cycling must be assessed. Thermal and pressure cycling and hydrodynamic testing will be conducted to verify seal integrity of the steel to zircaloy hub coupling when subjected to ATR conditions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Grain-resolved temperature-dependent anisotropy in hexagonal Ti-7Al revealed by synchrotron X-ray diffraction

Hexagonal metals have anisotropic coefficients of thermal expansion causing grain-level internal stresses during heating. High energy x-ray diffraction microscopy, a non-destructive, in situ, micromechanical and microstructural characterization technique, has been used to determine the anisotropic coefficients of thermal expansion (CTEs) for Ti-7Al. Two samples of polycrystalline α-phase Ti-7Al were continuously heated from room temperature to 850 °C while far-field HEDM scans were collected. The results showed a change in the ratio of the CTEs in the ‘a’ and ‘c’ directions which explains discrepancies found in the literature. The CTE additionally appears to be affected by the dissolution of α 2 precipitates. Analysis of the grain-resolved micromechanical data also shows reconfiguration of the grain scale stresses likely due to anisotropic expansion driving crystallographic slip.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Crystal Growth Scale-Up and Stability of RbSr 2 X 5 :Eu Scintillators

The discovery and development of new scintillation materials support national security needs. In these applications, large volumes of scintillator crystals are needed to achieve efficient screening for contraband. Therefore, one important step in the discovery of new scintillator compositions is testing their feasibility for scale-up and their stability. In this work, high-quality Ø22 mm crystals of two new scintillators RbSr 2 Br 5 :Eu and RbSr 2 I 5 :Eu were grown via the Vertical Bridgman method, and their scintillation properties were characterized. Here, the Ø22 mm RbSr 2 I 5 :Eu crystals could be grown with fast translation rates up to 3.5 mm/h. Both RbSr 2 Br 5 :Eu and RbSr 2 I 5 :Eu had high scintillation performance, including light yields of 46,000 and 61,000 ph/MeV, respectively, for Ø22 × 35 mm crystals. Additionally, properties related to physical stability were investigated, including the coefficients of thermal expansion via high-temperature X-ray diffraction (HTXRD) as well as moisture sensitivity. HTXRD confirmed the absence of solid–solid phase transitions and showed that RbSr 2 Br 5 had minimal thermal expansion anisotropy compared to RbSr 2 I 5 and some other inorganic metal halide scintillators, which favors the growth of large-sized crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development and application of a uranium mononitride (UN) potential: Thermomechanical properties and Xe diffusion

We report that atomic-scale modeling of thermophysical and defect properties of uranium mononitride (UN) plays an important role in establishing a better understanding and improved models of UN fuel performance. Having an accurate interatomic potential is crucial for generating reliable data at finite temperatures using molecular dynamic simulations. We report a new interatomic potential for UN, based on a combination of many-body and pairwise interactions, a simple form that we later show could be easily adapted to include Xe-U and Xe-N interactions, i.e., generating a U-N-Xe interatomic potential. The potential was fitted to experimental thermal expansion and single crystal elastic constants, as well as Frenkel, Schottky, anti-Schottky, and antisite pair reaction energies from density functional theory (DFT) calculations. Using the potential, we successfully reproduced experimental lattice parameters, thermal expansion, single crystal elastic constants, and temperature dependent heat capacity. The potential also performs reasonably well in reproducing the energy of the aforementioned stoichiometric defect reactions and defect migration barriers calculated using DFT. However, the potential underestimates the energy difference between the tetrahedral and dumbbell uranium interstitials, and a more complex potential form might be needed to overcome this issue. The potential was also used to predict UN single crystal elastic constants and elastic properties at different temperatures, showing that UN becomes softer and more compressible with increasing temperature. We also compare our potential against literature data from previous empirical potentials, demonstrating similar or better behavior depending on the property of interest. To enable the simulation of Xe in UN a Buckingham potential has been fitted to DFT-derived Xe incorporation energies. The potential was then used to determine the activation energy for Xe diffusion due to various Xe-containing defects, with {XeU : VU} exhibiting the lowest activation energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Design, Fabrication, and Screening of Environmental‐Thermal Barrier Coatings Prepared by Ultrafast High‐Temperature Sintering

Abstract The demand for more efficient gas turbines relies heavily on the development of new environmental‐thermal barrier coatings (ETBCs). However, there is still uncertainty about which alloys and composites will be used for the next generation of turbine blades, as well as the most promising coating materials. Herein, an ETBCs development strategy is presented by integrating the coating design, synthesis, and screening using an ultrafast high temperature sintering (UHS) technique to accelerate coating improvements. The initial basis for composition selection is their thermal expansion mismatch with the substrate alloys; for which a temperature‐dependent coefficient of thermal expansion database is created. By combining tape casting method with the UHS technique a high‐throughput synthesis of single and multi‐layer coatings are realized with different compositions, layer stacking sequences, and layer thicknesses. To evaluate the coatings, thermal cycling tests from room temperature to 1300 °C are conducted. The approach enabled coatings on objects with complex geometries, multi‐layer ETBCs, and porosity tailoring by using staged UHS that runs with different temperatures and durations. The fast iteration strategy is more cost‐effective for the screening of ETBCs compared to conventional methods and greater throughput which can be further extended for rapid optimization of other materials systems.

Xie, Hua↗
DOE OSTI2024

Convergent laser beam shapes: Unveiling the dynamics of Laser-induced elastic waves in composite materials

Overcoming the low signal-to-noise ratio (SNR) in laser ultrasonic testing of composite materials remains a significant challenge. Current efforts focus on enhancing SNR by inserting more energy into the material through temporal and/or spatial modulation of the laser beam. However, potential SNR improvements through wave convergence and wave energy manipulation have been overlooked. This paper addresses this gap by demonstrating the convergence of different wave types to a designated point and by showing the feasibility of directing absorbed laser energy into a specific wave type through spatial modulation of the laser beam. To achieve this, mathematical expressions for the convergent laser beams are derived. Various laser beam profiles are then introduced to the thermoelastic equations and solved using the finite element method. The sample under investigation is a transversely isotropic unidirectional carbon fiber reinforced plastic, characterized by anisotropic thermal expansion coefficients and thermal conductivities. Results reveal pronounced convergence of the intended wave type at the center due to laser beam shaping. This study showcases the ability to direct absorbed laser energy toward a specific wave type through spatial modulation of the laser beam and highlights the role of material anisotropy in energy focusing.

composite materials↗
DOE OSTI2021

Liquid metallic laser ultrasound transducer for high-temperature applications

This study aims to investigate a laser ultrasound (LUS) transducer for high-temperature (>100 °C) applications. For decades, many researchers have investigated efficient LUS transducers, yet studies on laser ultrasound transducers capable of performing at the high-temperature condition are rarely found in the literature. Most current LUS transducers still utilize a polymer-based composite material, that is, not stable at varying temperature conditions. This study introduces a liquid metallic (LM) LUS transducer that utilizes field's metal, which has a high thermal expansion (~3 × 10 -4 K -1 ). We hypothesized that such a high thermal expansion of the liquid metal can effectively produce laser-generated ultrasound waves, substituting for conventional polymer-based transducers. A numerical simulation predicted that the LM LUS transducer would produce higher LUS intensity (~22 dB) than that without the LUS transducer. Experiment results confirmed that the LM transducer effectively intensifies the ultrasound wave signals, obtaining a signal-to-noise gain over 30 dB. Moreover, the transducer was found capable of transmitting detectable wave packets in relatively high-temperature conditions (~400 °C), while conventional candle soot nanoparticle-polydimethylsiloxane could not perform stably at these elevated temperatures. The investigations introduced in this article are scientifically significant since we demonstrated the engineering feasibility of liquid metallic materials for LUS transducers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Razorback – A reactor transient analysis code for large rapid reactivity additions in a natural circulation research reactor

Research reactors play an important role in higher education, scientific research, and medical radioisotope production around the world. It is thus important to ensure the safety of facility workers and the public. This work presents a new reactor transient analysis code referred to as Razorback. The code has been developed for the evaluation of large rapid reactivity addition in research reactors. Its initial focus is the Annular Core Research Reactor (ACRR) at Sandia National Laboratories. Results have been validated against ACRR pulse operations. Razorback models the reactor kinetics, fuel element heat transfer, fuel element thermal expansion, and natural circulation coolant channel thermal-hydraulic response. Simulation results for ACRR pulse operations are shown to agree very well with operational data obtained from the ACRR. Finally, Razorback is expected to be a valuable tool for ACRR pulse performance prediction and ACRR reactor safety analyses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Thermal, mechanical, and electrical properties of LSCo/mullite composite contact materials for solid oxide fuel cells

Lanthanum strontium cobaltite (LSCo) is considered as a good candidate cathode contact material for solid oxide fuel cells, due to high electrical conductivity. However, LSCo has a very large coefficient of thermal expansion (CTE) than the cells and metallic interconnects. As a result, poor mechanical stability is expected during thermal cycling. To minimize the CTE mismatch, we investigate a composite approach involving mixing LSCo with an inert material of low CTE, such as mullite at volume fractions from 0.1 to 0.4. Composite’s CTE shows a decreasing trend with increasing mullite volume fractions, and is consistent with model predictions. X-ray powder diffraction analysis of sintered LSCo/mullite composites exhibits no presence of other phases for samples aged for 500h at 800oC, indicating chemical compatibility. Electrical conductivity by a 4-pt method shows a decreasing trend with increasing mullite content. Contact strength of as-sintered and thermally cycled samples show that only the composite with 0.4 volume fraction has a measurable strength; the other composites have no strength. Overall, the composite approach is demonstrated in the LSCo/mullite system to lower the CTE and hence achieve thermal cycle stability. The addition of the inert phase to the LSCo matrix; however, also reduces the electrical conductivity.

Contact materials, LSCo, mullite, CTE, electrical ↗