SEARCH · Search NASA

Results for “TOUGH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Rate effects on delamination fracture toughness of graphite/epoxy composites

The effects of loading rate on interlaminar fracture toughness were investigated for two graphite/epoxy materials, one with a brittle matrix and the other with a toughened one. Mode I delamination fracture toughness was studied by means of uniform-width, width-tapered, and height-tapered double cantilever beam specimens. The specimens were loaded at various crosshead rates corresponding to crack extension rates up to 26 m/s. It was found that for the brittle-matrix composite the energy release rate increases up to a certain crack velocity and thereafter it decreases. In the case of the toughened-matrix composite the energy release rate decreases monotonically with increasing crack velocity.

Daniel, I. M.↗

NASA NTRS1988

Fracture toughness computational simulation of general delaminations in fiber composites

A procedure is described to computationally simulate composite laminate fracture toughness in terms of strain energy release rate (SERR). It is also used to evaluate the degradation in laminate structural integrity in terms of displacements, loss in stiffness, loss in vibration frequencies and loss in buckling resistance. Specific laminates are selected for detail studies in order to demonstrate the generality of the procedure. These laminates had center delaminations, off-center delaminations, and pocket delaminations (center and off-center) at the free-edge and center delaminations at the interior. The laminates had two different thicknesses and were made from three different materials. The results obtained are presented in graphical form to illustrate the effects of delamination on the laminate structural integrity and on the laminate strain energy release rate (composite fracture toughness).

Murthy, P. L. N.↗

NASA NTRS1988

Fracture toughness computational simulation of general delaminations in fiber composites

A procedure is described to computationally simulate composite laminate fracture toughness in terms of strain energy release rate. It is also used to evaluate the degradation in laminate structural integrity in terms of displacements, loss in stiffness, loss in vibration frequencies and loss in buckling resistance. Specific laminates are selected for detail studies in order to demonstrate the generality of the procedure. These laminates had center delaminations, off-center delaminations, and pocket delaminations (center and off-center) at the free-edge and center delaminations at the interior. The laminates had two different thicknesses and were made from three different materials. The results obtained are presented in graphical form to illustrate the effects of delamination on the laminate structural integrity and on the laminate strain energy release rate (composite fracture toughness).

Wilt, T. E.↗

NASA NTRS1988

Semi-interpenetrating polymer network's of polyimides: Fracture toughness

The objective was to improve the fracture toughness of the PMR-15 thermosetting polyimide by co-disolving LaRC-TPI, a thermoplastic polyimide. The co-solvation of a thermoplastic into a thermoset produces an interpenetration of the thermoplastic polymer into the thermoset polyimide network. A second research program was planned around the concept that to improve the fracture toughness of a thermoset polyimide polymer, the molecular weight between crosslink points would be an important macromolecular topological parameter in producing a fracture toughened semi-IPN polyimide.

Hansen, Marion Glenn↗

NASA NTRS1989

Effect of microstructure and notch root radius on fracture toughness of an aluminum metal matrix composite

Recent results on the effects of matrix aging condition (matrix temper) and notch root radius on the measured fracture toughness of a SiC particulate reinforced aluminum alloy are reviewed. Stress intensity factors at catastrophic fracture were obtained for both underaged and overaged composites reveal. The linear relation found between apparent fracture toughness and the square root of the notch root radius implies a linear dependence of the crack opening displacement on the notch root radius. The results suggest a strain controlled fracture process, and indicate that there are differences in the fracture micromechanisms of the two aging conditions.

Manoharan, M.↗

NASA NTRS1989

The interlaminar fracture toughness of woven graphite/epoxy composites

The interlaminar fracture toughness of 2-D graphite/epoxy woven composites was determined as a function of stacking sequence, thickness, and weave pattern. Plain, oxford, 5-harness satin, and 8-harness satin weaves of T300/934 material were evaluated by the double cantilever beam test. The fabric material had a G (sub Ic) ranging from 2 to 8 times greater than 0 degrees unidirectional T300/934 tape material. The interlaminar fracture toughness of a particular weave style was dependent on whether the stacking sequence was symmetric or asymmetric and, in some cases, on the fabric orientation.

Funk, Joan G.↗

NASA NTRS1990

Fracture toughness and crack growth of Zerodur

The fracture toughness and crack growth parameters of Zerodur, a low expansion glass ceramic material, were determined. The fracture toughness was determined using indentation techniques and was found to be 0.9 MPa x m(sup 1/2). The crack growth parameters were determined using indented biaxial specimens subjected to static and dynamic loading in an aqueous environment. The crack growth parameters n and 1n(B) were found to be 30.7 and -6.837, respectively. The crack growth parameters were also determined using indented biaxial specimens subjected to dynamic loading in an ambient 50 percent relative humidity environment. The crack growth parameters n and 1n(B) at 50 percent relative humidity were found to be 59.3 and -17.51, respectively.

Viens, Michael J.↗

NASA NTRS1989

Effect of particle size on fracture toughness of SiC/Al composite material

Discontinuous SiC/Al composites with SiC particles of different sizes were fabricated in order to study the role of particle size on the fracture process. The fracture process is confined to a very narrow band and takes place within the matrix in composites containing small SiC particle sizes. In the composite reinforced with SiC particles of 20 microns and above fracture of SiC begins to dominate. The matrix is influenced by the high density of dislocations generated at SiC/Al interfaces due to the difference in coefficient of thermal expansion between SiC and the Al matrix. Crack initiation fracture toughness does not depend on SiC particle size. Crack growth fracture toughness increases as the size of the SiC particle increase.

Flom, Y.↗

NASA NTRS1989

Strength and toughness of composite materials based on nickel aluminide matrices

Several nickel aluminide matrix composites were prepared using vacuum hot pressing techniques. The matrix compositions, based on Ni3Al, Ni3Al+B, and NiAl, were reinforced with 10 vol pct TiB2 particles. Both smooth- and notched-bend tests were conducted at room temperature on the monolithic as well as the reinforced materials in order to determine the effects of TiB2 reinforcement on both the smooth-bend and notched-bend properties. TiB2 additions were shown to improve the smooth-bend strengths regardless of the matrix composition, while notched-bend tests, conducted to provide estimates of fracture toughness, revealed somewhat lower values for the composites in comparison to the monolithic materials. Fractographic analyses and in situ fracture observations of the composites revealed that preferential fracture in regions of clustered TiB2 particles may significantly affect the measured toughnesses.

Rigney, J. D.↗

NASA NTRS1989

Aging effects on the fracture toughness of SiC whisker reinforced 2XXX aluminum alloys

The effect of aging (at 150 C) time on the fracture toughness behavior of a 2XXX alloy (Al-3.55Cu-1.29Mg-0.01Fe-trace Mn) reinforced with 5 vol pct F-8 SiC whiskers was investigated by measuring hardness and electrical conductivity followed by fracture toughness tests on center-cracked specimens. The ageing time-hardening response plots showed that, independent of whisker orientation, the initial rapid increase in hardness was followed by a more gradual increase, with a broad hardness peak between 32 and 128 hrs of aging. Coincident with the hardness changes, the electrical conductivity initially decreased, reached a minimum, and then increased at aging times beyond 32 hrs. Examination by SEM indicated that the initial increase in hardness and decrease in conductivity was due to the GPB zone formation, while the subsequent increase in electrical conductivity and decrease in hardness (overaging) was due to S nucleation and growth.

Ratnaparkhi, P. L.↗

NASA NTRS1989

Interlaminar fracture toughness of thermoplastic composites

Edge delamination tension and double cantilever beam tests were used to characterize the interlaminar fracture toughness of continuous graphite-fiber composites made from experimental thermoplastic polyimides and a model thermoplastic. Residual thermal stresses, known to be significant in materials processed at high temperatures, were included in the edge delamination calculations. In the model thermoplastic system (polycarbonate matrix), surface properties of the graphite fiber were shown to be significant. Cricital strain energy release rates for two different fibers having similar nominal tensile properties differed by 30 to 60 percent. The reason for the difference is not clear. Interlaminar toughness values for the thermoplastic polyimide composites (LARC-TPI and polyimidesulfone) were 3 to 4 in-lb/sq in. Scanning electron micrographs of the EDT fracture surfaces suggest poor fiber/matrix bonding. Residual thermal stresses account for up to 32 percent of the strain energy release in composites made from these high-temperature resins.

Hinkley, Jeffrey A.↗

NASA NTRS1990

Crack initiation and growth toughness of an aluminum metal-matrix composite

The effects of systematic changes in matrix microstructure on crack initiation and growth toughnesses were determined on an Al-Zn-Mg-Cu alloy containing 0, 15, 20 percent by volume of SiC particulates. Materials were heat treated to underaged (UA) and overaged (OA) conditions of equivalent matrix microhardness and flow stress. Although both the fracture initiation and growth toughnesses, as measured by JIc and tearing modulus, were similar for the unreinforced materials in the UA and OA conditions, significant effects of microstructure on both JIc and tearing modulus were observed in the composites. SEM and TEM observations of fracture paths in the two conditions are utilized to rationalize these observations in light of existing theories of ductile fracture propagation.

Manoharan, M.↗

NASA NTRS1989

Fracture toughness in SiC/Al composite material

Crack initiation fracture toughness does not depend on SiC particle size. Crack growth fracture toughness increases as the size of the SiC particle increases. The fracture process is confined to a very narrow band and takes place within the matrix. In the case of composite reinforced with SiC particles of 20 microns and above, fracture of SiC begins to dominate. The matrix is influenced by a triaxial tension in the matrix and a high density of dislocations generated at SiC/Al interfaces due to the difference in coefficient of thermal expansion between SiC and the Al matrix.

Flom, Y.↗

NASA NTRS1990

Matrix toughness, long-term behavior, and damage tolerance of notched graphite fiber-reinforced composite materials

The long-term behavior of notched graphite-fiber-reinforced composite laminates with brittle or tough matrix materials and different fiber architectures was investigated using damage measurements and stiffness change, residual strength, and life data. The fiber/matrix materials included T300/5208, AS4/3501-6, AS4/1808, AS4/PEEK, and C3000/PMR-15 matrices and unidirectional tape and woven cloth fiber architectures. Results of damage evaluation and of residual strength measurements during the fatigue damage development showed that the long-term behavior and damage tolerance are controlled by a number of interacting factors such as the matrix toughness, fiber architecture, loading levels, and damage types and distributions.

Bakis, C. E.↗

NASA NTRS1990

Functionalized poly(arylene ethers) as toughness modifiers for bismaleimides

A family of novel, low molecular weight functionalized poly(arylene ether) resins has been investigated to ascertain its members' toughness-imparting contribution to neat bismaleimide (BMI) resin and BMI-matrix laminate composite properties. Attention is given to the contribution of the reactive poly(arylene ether)'s backbone chemistry to fracture toughness, as well as to the comparative influence of high and low molecular weight reactive poly(arylene ether) types on the modified BMI resin systems. The modified BMIs possess a polyphase morphology, with good adhesion between the thermoplastic nodules and the host thermoset systems.

Stenzenberger, H. D.↗

NASA NTRS1991

Tough, High-Performance, Thermoplastic Addition Polymers

Series of addition-type thermoplastics (ATT's) exhibit useful properties. Because of their addition curing and linear structure, ATT polymers have toughness, like thermoplastics, and easily processed, like thermosets. Work undertaken to develop chemical reaction forming stable aromatic rings in backbone of ATT polymer, combining high-temperature performance and thermo-oxidative stability with toughness and easy processibility, and minimizing or eliminating necessity for tradeoffs among properties often observed in conventional polymer syntheses.

Pater, Ruth H.↗

NASA NTRS1991

Thermal characterization and toughness of ethynyl containing blends

As part of an effort to develop high performance structural resins with an attractive combination of properties for aerospace applications, a series of ethynyl-terminated polysulfones of different molecular weights were prepared and blended with a low molecular weight ethynyl-terminated coreactant. Upon heating above 200 C, these ethynyl containing materials react to form a chain extended and crosslinked network structure. This reaction renders the materials insoluble in common solvents, but also reduces the toughness as compared to high molecular weight linear polysulfones. The thermal characterization of these blends and the toughness of the resulting cured materials are discussed.

Jensen, Brian J.↗

NASA NTRS1991

Effect of initial delamination on Mode 1 and Mode 2 interlaminar fracture toughness and fatigue fracture threshold

Static and fatigue double-cantilever beam (DCB) and end-notch flexure (ENF) tests were conducted to determine the effect of the simulated initial delamination in interlaminar fracture toughness, G(sub c), and fatigue fracture threshold, G(sub th). Unidirectional, 24-ply specimens of S2/SP250 glass/epoxy were tested using Kapton inserts of four different thickness - 13, 25, 75, and 130 microns, at the midplane at one end, or with tension or shear precracks, to simulate an initial delamination. To determine G(sub c), the fatigue fracture threshold below which no delamination growth would occur in less than 1 x 10(exp 6) cycles, fatigue tests were conducted by cyclically loading specimens until delamination growth was detected. Consistent values of model 1 fracture toughness, G(sub Ic), were measured from DCB specimens with inserts of thickness 75 microns or thinner, or with shear precracks. The fatigue DCB tests gave similar values of G(sub Ith) for the 13, 25, and 75 microns specimens. Results for the shear precracked specimens were significantly lower that for specimens without precracks. Results for both the static and fatigue ENF tests showed that measured G(IIc) and G(IIth) values decreased with decreasing insert thickness, so that no limiting thickness could be determined. Results for specimens with inserts of 75 microns or thicker were significantly higher than the results for precracked specimens or specimens with 13 or 25 microns inserts.

Murri, Gretchen Bostaph↗