SEARCH · Search NASA

Results for “Thermomechanical behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Ceramic Matrix Composites (CMC) Life Prediction Method Development

Advanced launch systems (e.g., Reusable Launch Vehicle and other Shuttle Class concepts, Rocket-Based Combine Cycle, etc.), and interplanetary vehicles will very likely incorporate fiber reinforced ceramic matrix composites (CMC) in critical propulsion components. The use of CMC is highly desirable to save weight, to improve reuse capability, and to increase performance. CMC candidate applications are mission and cycle dependent and may include turbopump rotors, housings, combustors, nozzle injectors, exit cones or ramps, and throats. For reusable and single mission uses, accurate prediction of life is critical to mission success. The tools to accomplish life prediction are very immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for a variety of space propulsion applications. This paper describes an approach to satisfy the need to develop an integrated life prediction system for CMC that addresses mechanical durability due to cyclic and steady thermomechanical loads, and takes into account the impact of environmental degradation.

Levine, Stanley R.↗

NASA NTRS1975

Mechanical behavior of the directionally solidified gamma/gamma prime - delta eutectic alloy

The eutectic alloy Ni-20.0%Cb-2.5%Al-6.0%Cr was tested in short-term creep and long-term exposure to service conditions to assess its suitability for high temperature turbine blade applications. Long-time exposure showed the lamellar microstructure of the alloy to be exceptionally stable. Other properties tested were notch sensitivity, isothermal and thermomechanical fatigue strength, shear strength, and transverse ductility. It was shown that this alloy is superior to the best currently available directionally solidified superalloys over the temperature/stress conditions encountered in turbine airfoils.

Barkalow, R. H.↗

NASA NTRS2000

Comparison of The Dimensional Stability of Kel-F 81 and Neoflon CTFE M400H Polychlorotrifluoroethylenes Used in Valve Seat Application

The dimensional stability of polychlorotrifluoroethylene (PCTFE) valve seats used in oxygen regulator applications was determined by thermomechanical analysis (TMA). Two traceable grades of PCTFE were tested; Kel-F 81 and Neoflon CTFE M400H. For these particular resins, the effect of percent crystallinity, zero strength time (ZST) molecular weight, resin grade, process history (compression-molded versus extruded) on the dimensional stability and annealing behavior was determined. In addition to the traceable Kel-F 81 and Neoflon CTFE M400H grades, actual PCI'PH valve seats of differing geometry and design were tested by TMA. The PCTFE valve seats were of unspecified resin grade, although certain inferences about the grade could be drawn based on knowledge of the valve seat fabrication date. Results consistently revealed dimensional instability of varying magnitude at temperatures ranging from 40 to 70 degrees Celsius. Furthermore, some of the pre- 1 995 seats appeared to be more dimensionally stable than those fabricated after 1995. The TMA results are discussed in the context of several proposed ignition mechanisms; namely, particle impact, presence of contaminant oils and fibers, and localized heating by flow friction and/or resonance. The effect of metal constraint on the dimensional stability of PCTFE is also discussed. Finally, the effect of percent crystallinity, ZST molecular weight, resin grade, process history (compression-molded versus extruded) on the AIT, delta Hc and impact sensitivity of various types of Neoflon CTFE M400H was determined using Kel-F 81 as a control. Results show that the AIT, delta Hc and impact sensitivity were essentially independent of Neoflon CTFE process history and structure.

Waller, Jess M.↗

NASA NTRS2003

Modeling of 3-D Woven Ceramic Matrix Composites

Three different approaches are being pursued at the NASA Glenn Research Center to predict the nanostructural behavior of three-dimensional woven ceramic matrix composites. These are: a micromechanics-based approach using W-CEMCAN (Woven Ceramic Matrix Composite Analyzer), a laminate analogy method and a structural frame approach (based on the finite element method). All three techniques are applied to predict the thermomechanical properties of a three-dimensional woven angle interlock C/SiC composite. The properties are predicted for room temperature and 1100 C and the predicted properties are compared to measurements. General observations regarding the three approaches for three-dimensional composite modeling are discussed.

Murthy, Pappu L. N.↗

NASA NTRS1996

Comparison Testings between Two High-temperature Strain Measurement Systems

An experimental evaluation was conducted at NASA Lewis Research Center to compare and contrast the performance of a newly developed resistance strain gage, the PdCr temperature-compensated wire strain gage, to that of a conventional high-temperature extensometry. The evaluation of the two strain measurement systems was conducted through the application of various thermal and mechanical loading spectra using a high-temperature thermomechanical uniaxial testing system equipped with quartz lamp heating. The purpose of the testing was not only to compare and contrast the two strain sensors but also to investigate the applicability of the PdCr strain gage to the testing environment typically employed when characterizing the high-temperature mechanical behavior of structural materials. Strain measurement capabilities to 8OO C were investigated with a nickel base superalloy IN100 substrate material, and application to titanium matrix composite (TMC) materials was examined with the SCS-6/Ti-15-3 08 system. PdCr strain gages installed by three attachment techniques, namely, flame spraying, spot welding and rapid infrared joining were investigated.

Lei, J.-F.↗

NASA NTRS1978

The development and application of strainrange partitioning as a tool in the treatment of high temperature metal fatigue

The effects of frequency, stress and strain hold periods, stress and strain ramping, creep-fatigue interspersion, and thermomechanical cycling were studied. Of special interest was the establishment of a set of universalized life relations which were normalized by the ductility of the material. These relations together with a set of rules that were devised for treating multiaxiality by the method, were, for example, useful in predicting torsion behavior, and in particular in establishing a new relationship between torsion and tension that had previously not been considered. They also were useful in the development of a framework for treatment of environmental effects.

Manson, S. S.↗

NASA NTRSDate not supplied

Understanding the Durability of SiC Based Ceramic Matrix Composites (CMCs) for Gas Turbine Engine Hot Section Components

Silicon carbide fiber reinforced silicon carbide ceramic matrix composites (SiCf/SiC-CMCs) are being used in the fabrication of gas turbine engine hot section components due to their light weight and excellent thermal and chemical stabilities at high-temperature. These superior properties enable significant enhancements in engine efficiency and reduced fuel burn, emissions, and cooling requirements. In support of NASA’s Aeronautics Mission under various programs at Glenn Research Center, different types of composites have been developed and assessed for a high temperature (2700 °F) SiCf/SiC CMC system for turbine engine applications. These composites have creep-resistant SiC fibers, advanced 3D weaves, 2700 °F-capable hybrid SiC matrices, and durable environmental barrier coatings (EBCs). These efforts have resulted in improvements in the overall CMC thermomechanical and environmental durability. In order to study the role of different constituents and processing variables, a single fiber tow CVI (chemical vapor infiltration) SiC/SiC mini-composite can be considered the basic architectural feature of woven and laminate SiC/SiC CMCs. Moreover, the mini-composite mechanical and tensile creep damage behavior represents the creep behavior of 0° fiber tows in the axial loading direction of a macro-composite or component. In addition, a large number of mini-composite samples can be fabricated at relatively low cost within a short time, which makes them attractive for obtaining a robust set of experimental data and studying constituent behavior. In this presentation, the mini-composite approach to study damage mechanisms that limit CMC life in extreme environments including exposure to steam will be presented. The effects of constituent type and volume fraction on the CMC durability, which will help influence CMC design, will be discussed.

Ceramic Matrix Composites (CMCs)↗

NASA NTRS1996

High-Temperature Extensometry and PdCr Temperature-Compensated Wire Resistance Strain Gages Compared

Source record↗

NASA NTRS1997

High-Temperature Extensometry and PdCr Temperature-Compensated Wire Resistance Strain Gages Compared

A detailed experimental evaluation is underway at the NASA Lewis Research Center to compare and contrast the performance of the PdCr/Pt dual-element temperature-compensated wire resistance strain gage with that of conventional high-temperature extensometry. The advanced PdCr gage, developed by researchers at Lewis, exhibits desirable properties and a relatively small and repeatable apparent strain to 800 C. This gage represents a significant advance in technology because existing commercial resistance strain gages are not reliable for quasi-static strain measurements above approx. 400 C. Various thermal and mechanical loading spectra are being applied by a high-temperature thermomechanical uniaxial testing system to evaluate the two strain-measurement systems. This is being done not only to compare and contrast the two strain sensors, but also to investigate the applicability of the PdCr strain gage to the coupon-level specimen testing environment typically employed when the high-temperature mechanical behavior of structural materials is characterized. Strain measurement capabilities to 800 C are being investigated with a nickel-base superalloy, Inconel 100 (IN 100), substrate material and application to TMC's is being examined with the model system, SCS-6/Ti-15-3. Furthermore, two gage application techniques are being investigated in the comparison study: namely, flame-sprayed and spot welding. The apparent strain responses of both the weldable and flame-sprayed PdCr wire strain gages were found to be cyclically repeatable on both IN 100 and SCS-6/Ti-15-3 [0]_8. In general, each gage exhibited some uniqueness with respect to apparent strain behavior. Gages mounted on the IN 100 specimens tended to show a repeatable apparent strain within the first few cycles, because the thermal response of IN 100 was stable. This was not the case, however, for the TMC specimens, which typically required several thermal cycles to stabilize the thermal strain response. Thus, progressive changes in the apparent strain behavior were corroborated by the extensometer, which unlike the mounted gage can distinguish quantitative changes in the material's thermal strain response. One specimen was instrumented with both a fixed and floating gage. From the difference in output of these two gages, the thermal expansion strains were calculated. These data, which are given in the figure, show excellent agreement with the values measured by the high-temperature extensometry.

Source record↗

NASA NTRS1991

Microfracture in high temperature metal matrix laminates

Computational simulation procedures are described to evaluate the composite microfracture behavior, establish the hierarchy/sequence of fracture modes, and the influence of compliant layers and partial debonding on composite properties and microfracture initiation. These procedures are based upon three-dimensional finite element analysis and composite micromechanics equations. Typical results for the effects of compliant layers and partial debonding, microfracture initiation, and propagation and the thermomechanical cyclic loading on a SiC/Ti15 composite system are presented and discussed. The results show that interfacial debonding follows fiber or matrix fracture, and the thermomechanical cyclic loading severely degrades the composite integrity.

Mital, Subodh K.↗

NASA NTRS1990

Application of thermal life prediction model to high-temperature aerospace alloys B1900+Hf and Haynes 188

The results of the application of a newly proposed thermomechanical fatigue (TMF) life prediction method to a series of laboratory TMF results on two high-temperature aerospace engine alloys are presented. The method, referred to as TMF/TS-SRP, is based on three relatively recent developments: the total strain version of the method of Strainrange Partitioning (TS-SRP), the bithermal testing technique for characterizing TMF behavior, and advanced viscoplastic constitutive models. The high-temperature data reported in a companion publication are used to evaluate the constants in the model and to provide the TMF verification data to check its accuracy. Predicted lives are in agreement with the experimental lives to within a factor of approximately 2.

Halford, Gary R.↗

NASA NTRS1992

Application of a thermal fatigue life prediction model to high-temperature aerospace alloys B1900 + Hf and Haynes 188

The results of the application of a newly proposed thermomechanical fatigue (TMF) life prediction method to a series of laboratory TMF results on two high-temperature aerospace engine alloys are presented. The method, referred to as TMF/TS-SRP, is based on three relatively recent developments: the total strain version of the method of Strain Range Partitioning (TS-SRP), the bithermal testing technique for characterizing TMF behavior, and advanced viscoplastic constitutive models. The high-temperature data reported in a companion publication are used to evaluate the constants in the model and to provide the TMF verification data to check its accuracy. Predicted lives are in agreement with the experimental lives to within a factor of approximately 2.

Halford, G. R.↗

NASA NTRS1995

Materials research for High Speed Civil Transport and generic hypersonics: Adhesive durability

This report covers a portion of an ongoing investigation of the durability of adhesives for the High Speed Civil Transport (HSCT) program. Candidate HSCT adhesives need to possess the high-temperature capability required for supersonic flight. This program was designed to initiate an understanding of the behavior of candidate HSCT materials when subjected to combined mechanical and thermal loads. Two adhesives (K3A and FM57) and two adherends (IM7/K3B polymeric composite and the titanium alloy Ti-6Al-4V) were used to fabricate thick adherend lap shear specimens. Due to processing problems, only the FM57/titanium bonds could be fabricated successfully. These are currently undergoing thermomechanical fatigue (TMF) testing. There is an acute need for an adhesive to secondarily bond polymeric composite adherends or, alternately, polymeric composites that remain stable at the processing temperatures of today's adhesives.

Allen, Mark R.↗

NASA NTRS1984

Literature survey on oxidations and fatigue lives at elevated temperatures

Nickel-base superalloys are the most complex and the most widely used for high temperature applications such as aircraft engine components. The desirable properties of nickel-base superalloys at high temperatures are tensile strength, thermomechanical fatigue resistance, low thermal expansion, as well as oxidation resistance. At elevated temperature, fatigue cracks are often initiated by grain boundary oxidation, and fatigue cracks often propagate along grain boundaries, where the oxidation rate is higher. Oxidation takes place at the interface between metal and gas. Properties of the metal substrate, the gaseous environment, as well as the oxides formed all interact to make the oxidation behavior of nickel-base superalloys extremely complicated. The important topics include general oxidation, selective oxidation, internal oxidation, grain boundary oxidation, multilayer oxide structure, accelerated oxidation under stress, stress-generation during oxidation, composition and substrate microstructural changes due to prolonged oxidation, fatigue crack initiation at oxidized grain boundaries and the oxidation accelerated fatigue crack propagation along grain boundaries.

Liu, H. W.↗

NASA NTRS2018

Coupled Thermo-Mechanical Micromechanics Modeling of the Influence of Thermally Grown Oxide Layer in an Environmental Barrier Coating System

Environmental Barrier Coatings (EBCs) have emerged as a promising means of protecting silicon based ceramic matrix composite (CMC) components for high temperature applications (e.g., aircraft engines). EBCs are often used to protect an underlying material (substrate) such as silicon carbide from extreme thermal/chemical environments. In a typical CMC/EBC system, an EBC may or may not be adhered to an underlying substrate with a bond coat (e.g., silicon). Irrespective, systems that utilize EBCs are susceptible to a number of failure modes including oxidation/delamination, recession, chemical attack and dissolution, thermomechanical degradation, erosion, and foreign object damage. Current work at NASA Glenn Research Center is aimed at addressing these failure modes in EBC systems and developing robust analysis tools to aid in the design process. The Higher-Order Theory for Functionally Graded Materials (HOTFGM), a precursor to the High-Fidelity Generalized Method of Cells micromechanics approach, was developed to investigate the coupled thermo-mechanical behavior of functionally graded composites and will be used herein to assess the development and growth of a low-stiffness thermally grown oxide (TGO) layer in EBC/CMC systems without a silicon bond coat. To accomplish this a sensitivity study is conducted to examine the influence of uniformly and nonuniformly grown oxide layer on the associated driving forces leading to mechanical failure (spallation) of EBC layer when subjected to isothermal loading.

thermally grown oxide↗

NASA NTRS1991

Analysis of thermomechanical fatigue of unidirectional titanium metal matrix composites

Thermomechanical fatigue (TMF) data was generated for a Ti-15V-3Cr-3Al-3Sn (Ti-15-3) material reinforced with SCS-6 silicon carbide fibers for both in-phase and out-of-phase thermomechanical cycling. Significant differences in failure mechanisms and fatigue life were noted for in-phase and out-of-phase testing. The purpose of the research is to apply a micromechanical model to the analysis of the data. The analysis predicts the stresses in the fiber and the matrix during the thermal and mechanical cycling by calculating both the thermal and mechanical stresses and their rate-dependent behavior. The rate-dependent behavior of the matrix was characterized and was used to calculate the constituent stresses in the composite. The predicted 0 degree fiber stress range was used to explain the composite failure. It was found that for a given condition, temperature, loading frequency, and time at temperature, the 0 degree fiber stress range may control the fatigue life of the unidirectional composite.

Mirdamadi, M.↗

NASA NTRS1981

Boundary layer thermal stresses in angle-ply composite laminates, part 1

Thermal boundary-layer stresses (near free edges) and displacements were determined by a an eigenfunction expansion technique and the establishment of an appropriate particular solution. Current solutions in the region away from the singular domain (free edge) are found to be excellent agreement with existing approximate numerical results. As the edge is approached, the singular term controls the near field behavior of the boundary layer. Results are presented for cases of various angle-ply graphite/epoxy laminates with (theta/-theta/theta/theta) configurations. These results show high interlaminar (through-the-thickness) stresses. Thermal boundary-layer thicknesses of different composite systems are determined by examining the strain energy density distribution in composites. It is shown that the boundary-layer thickness depends on the degree of anisotropy of each individual lamina, thermomechanical properties of each ply, and the relative thickness of adjacent layers. The interlaminar thermal stresses are compressive with increasing temperature. The corresponding residual stresses are tensile and may enhance interply delaminations.

Wang, S. S.↗

NASA NTRS1987

Non-isothermal elastoviscoplastic snap-through and creep buckling of shallow arches

The problem of buckling of shallow arches under transient thermomechanical loads is investigated. The analysis is based on nonlinear geometric and constitutive relations, and is expressed in a rate form. The material constitutive equations are capable of reproducing all non-isothermal, elasto-viscoplastic characteristics. The solution scheme is capable of predicting response which includes pre and postbuckling with creep and plastic effects. The solution procedure is demonstrated through several examples which include both creep and snap-through behavior.

Simitses, G. J.↗