Search NASA⌕ Search

SEARCH · Search NASA

Results for “Trajectory Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Influence of Ohio River Valley Emissions on Fine Particle Sulfate Measured from Aircraft over Large Regions of the Eastern United States and Canada during INTEX-NA

Aircraft measurements of fine inorganic aerosol composition were made with a particle-into-liquid sampler coupled to dual ion chromatographs (PILS-IC) as part of the NASA INTEX-NA study. The sampling campaign, which lasted from 1 July to 14 August 2004, centered over the eastern United States and Canada and showed that sulfate was the dominant inorganic species measured. The highest sulfate concentrations were observed at altitudes below 2 km, and back trajectory analyses showed a distinct difference between air masses that had or had not intercepted the Ohio River valley (ORV) region. Air masses encountered below 2 km with a history over the ORV had sulfate concentrations that were higher by a factor of 3.2 and total sulfur (S) concentrations higher by 2.5. The study's highest sulfate concentrations were found in these air masses. The sulfur of the ORV air masses was also more processed with a mean sulfate to total sulfur molar ratio of 0.5 compared to 0.3 in non-ORV measurements. Results from a second, independent trajectory model agreed well with those from the primary analysis. These ORV-influenced air masses were encountered on multiple days and were widely spread across the eastern United States and western Atlantic region.

Hennigan, Christopher J.↗
NASA NTRS2007

Range Measurement as Practiced in the Deep Space Network

Range measurements are used to improve the trajectory models of spacecraft tracked by the Deep Space Network. The unique challenge of deep-space ranging is that the two-way delay is long, typically many minutes, and the signal-to-noise ratio is small. Accurate measurements are made under these circumstances by means of long correlations that incorporate Doppler rate-aiding. This processing is done with commercial digital signal processors, providing a flexibility in signal design that can accommodate both the traditional sequential ranging signal and pseudonoise range codes. Accurate range determination requires the calibration of the delay within the tracking station. Measurements with a standard deviation of 1 m have been made.

range measurement↗
NASA NTRS2007

Effects of Convective Ice Lofting on H2O and HDO in the Tropical Tropopause Layer

We have added convective ice lofting to a Lagrangian trajectory model of near-tropopause water vapor (H2O) and its isotopologue HDO. The ice lofting simulation is based on a parameterization derived from Aura Microwave Limb Sounder (MLS) icewater content measurements. In previous papers, the Lagrangian model has accurately interannual and seasonal H2O abundances; there was no need for convection to be included in the model. We show here that this model does a poor job of simulating near-tropopause HDO, but that the addition of convective ice lofting greatly improves the HDO simulation. Convective ice lofting has a small effect on lower stratospheric H2O. H2O there is set by the minimum temperature encountered at the cold-point tropopause, so H2O added by convection below this level does not make it through this cold point and into the lower stratosphere. Thus, adding convection to the model does not degrade the model's previously demonstrated accurate simulations of H2O. We conclude that the HDO data suggest an important role for convective mass flux into the so-called tropical tropopause layer.

Dessler, A. E.↗
NASA NTRS2008

Satellite Remote Sensing of Atmospheric Pollution: the Far-Reaching Impact of Burning in Southern Africa

When the first observations of a tropospheric trace gas were obtained in the 1980s, carbon monoxide enhancements from tropical biomass burning dominated the observed features. In 2005, an active remote-sensing system to provide detailed information on the vertical distribution of aerosols and clouds was launched, and again, one of the most imposing features observed was the presence of emissions from tropical biomass burning. This paper presents a brief overview of space-borne observations of the distribution of trace gases and aerosols and how tropical biomass burning, primarily in the Southern Hemisphere, has provided an initially surprising picture of the distribution of these species and how they have evolved from prevailing transport patterns in that hemisphere. We also show how interpretation of these observations has improved significantly as a result of the improved capability of trajectory modeling in recent years and how information from this capability has provided additional insight into previous measurements form satellites. Key words: pollution; biomass burning; aerosols; tropical trace gas emissions; Southern Hemisphere; carbon monoxide.

Fishman, Jack↗
NASA NTRS2010

Dispersion and Lifetime of the SO2 Cloud from the August 2008 Kasatochi Eruption

Hemispherical dispersion of the SO2 cloud from the August 2008 Kasatochi eruption is analyzed using satellite data from the Ozone Monitoring Instrument (OMI) and the Goddard Trajectory Model (GTM). The operational OMI retrievals underestimate the total SO2 mass by 20-30% on 8-11 August, as compared with more accurate offline Extended Iterative Spectral Fit (EISF) retrievals, but the error decreases with time due to plume dispersion and a drop in peak SO2 column densities. The GTM runs were initialized with and compared to the operational OMI SO2 data during early plume dispersion to constrain SO2 plume heights and eruption times. The most probable SO2 heights during initial dispersion are estimated to be 10-12 km, in agreement with direct height retrievals using EISF algorithm and IR measurements. Using these height constraints a forward GTM run was initialized on 11 August to compare with the month-long Kasatochi SO2 cloud dispersion patterns. Predicted volcanic cloud locations generally agree with OMI observations, although some discrepancies were observed. Operational OMI SO2 burdens were refined using GTM-predicted mass-weighted probability density height distributions. The total refined SO2 mass was integrated over the Northern Hemisphere to place empirical constraints on the SO2 chemical decay rate. The resulting lower limit of the Kasatochi SO2 e-folding time is approx.8-9 days. Extrapolation of the exponential decay back in time yields an initial erupted SO2 mass of approx.2.2 Tg on 8 August, twice as much as the measured mass on that day.

Krotkov, N. A.↗
NASA NTRS2012

Modeling of Aerobrake Ballute Stagnation Point Temperature and Heat Transfer to Inflation Gas

A trailing Ballute drag device concept for spacecraft aerocapture is considered. A thermal model for calculation of the Ballute membrane temperature and the inflation gas temperature is developed. An algorithm capturing the most salient features of the concept is implemented. In conjunction with the thermal model, trajectory calculations for two candidate missions, Titan Explorer and Neptune Orbiter missions, are used to estimate the stagnation point temperature and the inflation gas temperature. Radiation from both sides of the membrane at the stagnation point and conduction to the inflating gas is included. The results showed that the radiation from the membrane and to a much lesser extent conduction to the inflating gas, are likely to be the controlling heat transfer mechanisms and that the increase in gas temperature due to aerodynamic heating is of secondary importance.

Bahrami, Parviz A.↗
NASA NTRS2016

Wind Tunnel and Hover Performance Test Results for Multicopter UAS Vehicles

There is currently a lack of published data for the performance of multicopter unmanned aircraft system (UAS) vehicles, such as quadcopters and octocopters, often referred to collectively as drones. With the rapidly increasing popularity of multicopter UAS, there is interest in better characterizing the performance of this type of aircraft. By studying the performance of currently available vehicles, it will be possible to develop models for vehicles at this scale that can accurately predict performance and model trajectories. This paper describes a wind tunnel test that was recently performed in the U.S. Army's 7- by 10-ft Wind Tunnel at NASA Ames Research Center. During this wind tunnel entry, five multicopter UAS vehicles were tested to determine forces and moments as well as electrical power as a function of wind speed, rotor speed, and vehicle attitude. The test is described here in detail, and a selection of the key results from the test is presented.

Multicopter UAS↗
NASA NTRS2016

UAS Integration in the NAS Project: Flight Test 3 Data Analysis of JADEM-Autoresolver Detect and Avoid System

The Unmanned Aircraft Systems Integration in the National Airspace System project, or UAS Integration in the NAS, aims to reduce technical barriers related to safety and operational challenges associated with enabling routine UAS access to the NAS. The UAS Integration in the NAS Project conducted a flight test activity, referred to as Flight Test 3 (FT3), involving several Detect-and-Avoid (DAA) research prototype systems between June 15, 2015 and August 12, 2015 at the Armstrong Flight Research Center (AFRC). This report documents the flight testing and analysis results for the NASA Ames-developed JADEM-Autoresolver DAA system, referred to as 'Autoresolver' herein. Four flight test days (June 17, 18, 22, and July 22) were dedicated to Autoresolver testing. The objectives of this test were as follows: 1. Validate CPA prediction accuracy and detect-and-avoid (DAA, formerly known as self-separation) alerting logic in realistic flight conditions. 2. Validate DAA trajectory model including maneuvers. 3. Evaluate TCAS/DAA interoperability. 4. Inform final Minimum Operating Performance Standards (MOPS). Flight test scenarios were designed to collect data to directly address the objectives 1-3. Objective 4, inform final MOPS, was a general objective applicable to the UAS in the NAS project as a whole, of which flight test is a subset. This report presents analysis results completed in support of the UAS in the NAS project FT3 data review conducted on October 20, 2015. Due to time constraints and, to a lesser extent, TCAS data collection issues, objective 3 was not evaluated in this analysis.

flight test↗
NASA NTRS2014

Convective Influence and Transport Pathways Controlling the Tropical Distribution of Carbon Monoxide at 100 Hpa

Trajectory calculations with convective influence diagnosed from geostationary-satellite cloud measurements are used to evaluate the relative importance of different Tropical Tropopause Layer (TTL) transport pathways for establishing the distribution of carbon monoxide (CO) at 100 hPa as observed by the Microwave Limb Sounder (MLS) on board the Aura satellite. Carbon monoxide is a useful tracer for investigating TTL transport and convective influence because the CO lifetime is comparable to the time require for slow ascent through the TTL (a couple of months). Offline calculations of TTL radiative heating are used to determine the vertical motion field. The simple trajectory model does a reasonable job of reproducing the MLS CO distributions during Boreal wintertime and summertime. The broad maximum in CO concentration over the Pacific is primarily a result of the strong radiative heating (indicating upward vertical motion) associated with the abundant TTL cirrus in this region. Sensitivity tests indicate that the distinct CO maximum in the Asian monsoon anticyclone is strongly impacted by extreme convective systems with detrainment of polluted air above 360 K potential temperature. The relative importance of different CO source regions will also be discussed.

Tropical Tropopause Layer (TTL)↗
NASA NTRS2019

A Comparison of Boundary Layer Wind Profilers for Use with Space Launch Vehicles

The United States Air Force (USAF) operates two space launch ranges, the Eastern Range (ER) and the Western Range (WR). The ER is primarily located at the Cape Canaveral Air Force Station (CCAFS) and the WR is located at the Vandenberg Air Force Base (VAFB). Multiple systems are used to measure the atmosphere at both ranges, including a suite of 915-Mhz (megahertz) Doppler Radar Wind Profilers (DRWP). The 915-MHz DRWPs are used to measure winds in the lowest few kilometers of the atmosphere, primarily in the boundary layer. Boundary layer winds are important during launch, and observations of such can be used as input to toxic dispersion and low-level abort trajectory models. However, these 915-MHz systems are nearing the end of their service life and need to be replaced by systems with similar, or greater, capabilities. The USAF funded evaluations of two systems: a 449-MHz DRWP and a Lidar. Both systems were stationed at each range for separate periods of approximately three months from November 2017 through May 2018. The USAF also funded NASA’s Marshall Space Flight Center (MSFC) Natural Environments Branch (NE) to evaluate wind output from the two systems. MSFC NE conducted analysis to demonstrate the system’s wind accuracy relative to measurements from the Automated Meteorological Profiling System (AMPS) (Divers et al., 2000), data availability, and Effective Vertical Resolution (EVR).

Orcutt, John M.↗
NASA NTRS2019

Orbits Through Polytropes

We describe how orbital tunnels could be used to transport payloads through the Earth. If you use a brachistochrone for the tunnel, the body forces in the tunnel become overwhelmingly large for small angular distances traveled. Projectiles move along an orbital tunnel faster than they would along abrachistochrone connecting the same points but the body force components cancel. We describe how parabolic Keplerian orbits outside the object merge onto quasi-Keplerian orbits inside the object. We use models of the interior of the Earth with three values of the polytropic index (n) to calculate interior or bits that travel between surface points. The n¼3 results are also scaled to the Sun. Numerical integrations of the equations describing polytropes were used to generate the initial models. Numerical integration of the equations of motion are then used to calculate the angular distance you can travel along the surface and the traversal time as a function of the parabolic periaps is distance for each model. Trajectories through objects of low central condensation show a focusing effect that decreases as the central condensation increases. Analytic solutions for the trajectories in a homogeneous sphere are derived and compared to the numeric results. The results can be scaled to other planets, stars, or even globular clusters.

Gjerlov, Amalia↗
NASA NTRS2020

Overview of a Generalized Numerical Predictor-Corrector Targeting Guidance with Application to Human-Scale Mars Entry, Descent, and Landing

Recent advances in planetary entry guidance algorithms are motived by precision landing criteria for human-scale Mars missions and improved in-space computing capabilities. An NPC targeting guidance algorithm, originally developed for the Mars Surveyor Program 2001 Missions, has been modified and extended to permit a fully generalized, flexible, and robust approach to spacecraft aerocapture and EDL guidance design. This paper describes this generalized targeting NPC guidance (NPCG) and how its modifications enable its use in precision targeting for human missions. System modeling, trajectory propagation, and guidance segment definition and design are described. Finally, the NPCG capability and performance is demonstrated using a human-scale Mars entry, descent, and landing mission simulation.

Rafael A Lugo↗
NASA NTRS2021

Tracking aerosols and SO2 clouds from the Raikoke eruption: 3D view from satellite observations

The 21 June 2019 eruption of the Raikoke volcano (Kuril Islands, Russia; 48° N, 153° E) produced significant amounts of volcanic aerosols (sulfate and ash) and sulfur dioxide (SO2) gas that penetrated into the lower stratosphere. The dispersed SO2 and sulfate aerosols in the stratosphere were still detectable by multiple satellite sensors for many months after the eruption. For this study of SO2 and aerosol clouds we use data obtained from two of the Ozone Mapping and Profiler Suite sensors on the Suomi National Polar-orbiting Partnership satellite: total column SO2 from the Nadir Mapper and aerosol extinction profiles from the Limb Profiler as well as other satellite data sets. We evaluated the limb viewing geometry effect (the “arch effect”) in the retrieval of the LP standard aerosol extinction product at 674 nm. It was shown that the amount of SO2 decreases with a characteristic period of 8–18 d and the peak of stratospheric aerosol optical depth recorded at a wavelength of 674 nm lags the initial peak of SO2 mass by 1.5 months. Using satellite observations and a trajectory model, we examined the dynamics of an unusual atmospheric feature that was observed, a stratospheric coherent circular cloud of SO2 and aerosol from 18 July to 22 September 2019.

Eruption of the Raikoke volcano↗
NASA NTRSDate not supplied

Distribution of SLS Integrated Load Uncertainty to Surface Pressures and Sectional Loads

Aerodynamic loads that are important to launch vehicle programs such as NASA’s Space Launch System (SLS) include both integrated loads such as the force & moment on the entire vehicle and distributed loads. In this work two examples of distributed loads are considered: the pressure field on the surface of the vehicle and sectional loads, which are one-dimensional distributions along the axis of the launch vehicle. In some modern flight programs, the integrated loads, such as lift and drag, used to design the guidance and control laws for the vehicle come from wind tunnel testing, while distributed loads are produced using Computational Fluid Dynamics(CFD). The first task that is addressed in this paper, then, is to provide a formal method to adjust the distributed loads so that integrating them matches the prescribed integrated load. In addition, the integrated loads in a launch vehicle typically include an uncertainty estimate. The second task is to distribute this prescribed integrated uncertainty to each point in a distributed load. Both tasks are addressed using the same technique, which is to create distributed load profiles that isolate adjustments to one integrated load while leaving the others unaffected. These adjustments are informed by Proper Orthogonal Decomposition (POD) of the entire CFD-based distributed load database. Once applied, the adjusted distributed loads can be used to evaluate any scalar quantity of interest that might be needed by downstream users such as structural analysis or trajectory modelers.

SLS↗
NASA NTRS2022

Analysis and Impact of the Hunga Tonga-Hunga Ha’apai Stratospheric Water Vapor Plume

On Jan. 15, 2022, the Hunga Tonga-Hunga Ha’apai eruption injected SO2 and H2O into the 31 middle stratosphere. The eruption produced a persistent mid-stratospheric sulfate aerosol and H2O layer mostly confined to Southern Hemisphere (SH) tropics (Eq. to 30°S). These layers are still present in the tropics 5 ½ months after the eruption. The SH tropical confinement is simulated using a trajectory model. Measurements following the eruption show that the H2O layer is slowly rising while the aerosol layer is descending. The H2O layer’s upward movement is consistent with the residual vertical velocity. Gravitationally settling explains the descent of the aerosol layer. A -4K temperature anomaly coincident with the H2O enhancement is observed and is caused by thermal adjustment to the additional H2O IR cooling. A simple model of volcanic water injection at the time of the eruption simulates the observed vertical distribution H2O.

Atmospheric science↗
NASA NTRSDate not supplied

Expanding the Time Dimension of Hyperspectral Infrared Sounding Observations: Designing the NUCAPS-Forecast System

Low Earth orbit (LEO) hyper-spectral infrared (IR) sounders have significant yet untapped potential for characterizing thermodynamic environments of convective initiation and ongoing convection. While LEO soundings are of enormous value to weather forecasters, they cannot provide the temporal resolution needed to resolve the rapidly evolving thermodynamics of the convective environment. A novel methodology was developed to extend snapshots of LEO soundings forward in time up to six hours into the future and has been made available within the NOAA National Weather Service Advanced Weather Interactive Processing System (AWIPS) for testing in a quasi-operational setting. This methodology is based on parcel forward-trajectory calculations from the satellite observing time to recreate future soundings of temperature and moisture at regularly gridded intervals in space and time. The soundings are based on NOAA-Unique Combined Atmospheric Processing System (NUCAPS) retrievals from the Suomi NPP and NOAA-20 satellite platforms to allow for rapid near-real time product processing. Science code was transitioned to operational production in 2019 and the product, NUCAPS-Forecast, was tested at the NOAA Hazardous Weather Testbed Spring Experiment in 2019 and 2021. Forecaster feedback has led to improving the product and processing system to address product limitations and improve its applicability for pre-convective forecasting. This presentation highlights the design of the NUCAPS-Forecast system. Solutions were tested and implemented to remove excess moisture and conjoin forward-trajected parcels into vertical profiles for calculating grids of stability indices. Additionally, use cases that explore the tendencies of derived convective available potential energy (CAPE) and convective inhibition (CIN) were investigated. When evaluated against gridded, hourly accumulated rainfall obtained from the Multi-Radar Multi-Sensor (MRMS) observational data set areas with elevated CAPE (reduced CIN) are shown to be associated with areas of precipitation and increase confidence the LEO soundings advected forward in time physically represent atmospheric processes. These results suggest that adiabatic parcel advection of LEO satellite sounding snapshots forward in time exhibits skill in discriminating locations and times that are more likely to lead to convective initiation. Leveraging trajectory modeling to increase the spatial and temporal resolution of LEO IR sounding observations today demonstrates the value of these observations from the future constellation of JPSS satellites and GeoXO mission.

weather↗
NASA NTRSDate not supplied

ACS3 - Flight Dynamics for A Solar Sail Technology Demonstration Mission

The NASA's Advanced Composite Solar Sail System (ACS3) mission consist of a spacecraft that will deploy an 80 m 2 solar sail in a 1000 km sun-synchronous orbit. The main objective of the mission is to demonstrate that the solar wind can impulse the spacecraft to change the semimajor-axis and obtain a different orbit altitude. The sail will be composed of a combination of composite materials with distinct properties, and it will be deployed with lightweight booms from a 12U CubeSat bus, developed by Nanoavionics. The spacecraft will be launched aboard an Electron launch vehicle from Rocket LAB Launch Complex in New Zealand no earlier than July 2023. This paper covers the orbital mechanics and navigation developments to support the mission, from the solar sail trajectory model to the actual flight dynamics system to provide the orbit determination analysis prior to flight. First, we introduce a description of our high-fidelity propagation that accounts for the solar radiation pressure to produce predictive ephemeris of the solar sail performance with several spacecraft attitude modes. As part of our results, we present plots of the expected altitudes achieved by the spacecraft once the solar sail is deployed under various assumptions of the solar weather. In addition to that, we present a full description of our orbit determination process which relies in GPS state vectors to accurately estimate the position and velocity uncertainties at a frequent cadence during the mission. The outcome of this process will be critical to achieving the objective of determining effective altitude change produced by the solar sail.

Solar Sail↗