Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transmission electron microscopy (TEM)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cold Spray Deposition of 304L Stainless Steel to Mitigate Chloride-Induced Stress Corrosion Cracking in Canisters for Used Nuclear Fuel Storage

A feasibility study of the cold spray deposition process of 304L stainless steel on 304L stainless steel substrates as a mitigation method for chloride-induced stress corrosion cracking (CISCC) has been investigated under various substrate conditions. The study is aimed at the application of this technology to mitigate CISCC that may potentially occur in or nearthe fusion welded regions of stainless steel canisters in Dry Cask Storage System (DCSS) for used nuclear fuels. Spherical gas-atomized 304L stainless steel powder, in the size range of 25 µm to 44 µm, was used as a feedstock powder for the cold spray process. The powder was deposited on four types of 304L substrates with various surface conditions: as-polished, oxidized, cold-rolled, plates with prototypical CISCC. The effects of cold spray parameters on quality of cold spray coatings were investigated. Thickness, porosity, and phases in the as-deposited materials were evaluated using scanning electron microscopy (SEM) and X-ray diffraction (XRD), and correlated with microhardness and adhesion strength measured via micro-indentation and ASTM C633 pulling test, respectively. XRD analysis of the coatings was also conducted to examine the effects of cold spray condition on residual stress state in the coating. Detailed cross-sectional examination of coating/substrate interfaces was performed with transmission electron microscopy (TEM) equipped with energy dispersive spectroscopy (EDS). Dense and continuous coatings with good adhesion strength and hardness were produced for the various substrate conditions by adjusting cold spray parameters. The results demonstrate that cold spray stainless steel coating is a viable option to provide a physical barrier against CISCC in fusion weld regions of stainless steel in corrosive chloride salt-bearing environments.

Dry Cask Storage Systems, cold spray, 304L stainle↗
DOE OSTI2020

Disordering of helium gas bubble superlattices in molybdenum under ion irradiation and thermal annealing

Self-organization of gas bubbles causes the formation of an ordered array of nanoscale gas bubbles (a gas bubble superlattice), a highly efficient mechanism for gas storage under irradiation. Here, the stability of helium (He) gas bubble superlattices in molybdenum (Mo) under krypton (Kr) ion irradiation and thermal annealing has been investigated. The He gas bubble superlattices gradually become disordered under Kr ion irradiation at 300° C, and the order-disorder transformation process completes at 2.5 dpa. Both transmission electron microscopy (TEM) and synchrotron-based small-angle X-ray scattering (SAXS) reveal that the order-disorder transformation of He gas bubble superlattices is associated with a slight increase in the average bubble size. Phase-field modeling indicates that the inhomogeneous growth and coarsening of bubbles/voids cause the disordering of imperfect superlattices under irradiation and implies that highly ordered superlattices could potentially exhibit much stronger resistance to irradiation damage. Under thermal annealing, the He gas bubble superlattices in Mo become unstable and disordered at 1000° C with the bubble size increasing from ~1.1 to ~1.6 nm. The finding in this research provides insights into the disordering mechanisms of defect superlattices as well as guidance for designing stable defect superlattices in harsh environments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

α-U and ω-UZr 2 in neutron irradiated U-10Zr annular metallic fuel

Here, to develop metallic fuel with ultra-high burnup of 30%-40%, an annular U-10Zr fuel with 55% smear density was fabricated through a casting route and irradiated at the Advanced Test Reactor at Idaho National Laboratory. The annular fuel design also serves as a demonstration of the feasibility to replace sodium bond with a helium bond to benefit the geological disposal of irradiated fuel, cut the cost of fuel fabrication, and boost the overall metallic fuel economy. This paper reports the results from transmission electron microscopy (TEM) based post-irradiation examination of this fuel type irradiated to a burnup of 3.3% fissions per initial heave metal atoms for initial screening purpose. After irradiation, the initial U-10Zr separated into an a-U annular region and an UZr 2+x center region with nanoscale spinodal decomposed microstructure. Because of the provided large amount of coherent interface areas, the fission gas atoms and vacancies generated in UZr 2+x phase are possibly pinned at the interface areas, leading to 20 times smaller fission gas bubbles than those in the neighboring a-U. The large bubbles in a-U become connected and merged into large pores that provide fast release paths for fission gas which prevents further fuel swelling. The fuel center still has open space to accommodate further fuel swelling from solid fission products at higher burnup. Other neutron irradiation induced phase and microstructure change are also characterized and compared with traditional solid fuel designs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ monitoring of microstructure evolution during thermal processing of uranium-zirconium alloys using laser-generated ultrasound

In this study, laser-generated ultrasound was used to monitor microstructure evolution during thermal processing of as-cast, polycrystalline binary uranium-zirconium metallic fuel alloys with compositions of U-20wt.%Zr (U-20Zr), U-50wt.%Zr (U-50Zr) and U-80wt.%Zr (U-80Zr). Ultrasonic waveforms were recorded during heating and cooling the samples from room temperature to >973 K and back. A phase transition temperature for all three compositions was estimated from the temperature at which an abrupt and rapid reduction in ultrasonic velocities was observed. Microstructural features on the length scale of tens of micrometers were inferred from the observation of scattering of ultrasonic waves by elastic heterogeneities above ~823 K in U-20Zr, while a hysteresis in the ultrasonic velocities of U-80Zr upon cooling was attributed to a partial retention of the high temperature phase following thermal annealing. The U-50Zr alloy exhibited a reversible viscoelastic response above 933 K, as evidenced by the observation of high frequency attenuation of the shear component of the waveforms at high temperature. Ultrasonic measurements were supplemented by in situ transmission electron microscopy (TEM). The TEM images revealed that the δ-U-Zr matrix in the three compositions underwent a spinodal decomposition above ~823 K into nanoscale regions. The ultrasonic measurements revealed larger, micron-scale structure evolution in the U-20Zr alloy at the same temperature. This large-scale structure is associated with heterogeneous regions having different Zr content. Our findings show the potential heating rate dependence of microstructural evolution in U-Zr alloys and highlight differences in the thermomechanical response and associated length scales during thermal annealing between single- and dual-phase compositions. These results demonstrate the utility of laser ultrasonics to rapidly and efficiently scan phase boundaries and monitor micrometer-scale structure evolution in metallic fuel alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Post-irradiation characterization of a high burnup mixed oxide fuel rod with minor actinides

The Advanced Fuels Campaign performed a series of irradiation tests of minor actinide-bearing mixed oxide fuel (MA-MOX), the so-called AFC-2C&D experiments, to investigate the transmutation of long-lived transuranic actinide isotopes contained in spent nuclear fuel via fast reactor technology at burnups exceeding 10 % fission of initial metallic atoms. This manuscript reports the test results derived from one of the five MA-MOX rodlets taken to higher burnup in the AFC-2D irradiation. This includes both non-destructive investigations, such as gamma and neutron spectrometry, and destructive investigations, such as fission gas release, ceramography, and chemical burnup analysis. In addition, the microstructure of the fuel was investigated using advanced electron microscopy techniques including electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Here, it was observed with EBSD that the pellet had subdivision of the grains and the TEM observed migration of cladding material into the 5 metal precipitates in the fuel which could have been from the higher than desired oxygen/metal ratio. The TEM also showed an enrichment of Cr in fuel clad chemical interaction (FCCI) layer.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Microstructure analysis of laser beam weldments performed on neutron-irradiated 304L steel containing 3 and 8 appm helium

We report that AISI 304 L austenitic stainless steel is one of the major structural materials used in light water reactors (LWRs). In the future, 304 L components may require repair, and several welding techniques have been proposed as candidates. In this study, laser beam welding using the low-energy contribution approach was performed in ~2016 on neutron-irradiated AISI 304 L steel with nominal values of 3 and 8 appm helium (He). The goal was to investigate the impact of helium on the irradiated material weldability and evaluate helium-associated damage. The weld and heat-affected zone (HAZ) microstructure was studied using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy (TEM). Analysis of the weldment cross-sections did not reveal severe cracking. Still, evidence of incipient helium-associated damage was observed in the HAZ, manifesting as degraded grain boundaries (GBs) “decorated” by pore chains and mostly small (i.e., ≤ 25-30 µm) scattered cracks. The largest observed crack was ~50 µm in length. Helium-associated damage was localized within ~200-300 µm of the weld pool boundary, and the fraction of the compromised GBs, as a rule, was below ~9-11% of the total GB network. TEM analysis showed significant annealing of the radiation-induced defects at distances up to ~300 µm from the weld pool boundary. Inside the HAZ, the cavities (likely, helium bubbles) tended to form at GBs and inclusions, such as manganese sulfide precipitates in the grain interior. Crystallography analysis of the HAZ damage showed that random high-angle boundaries were most susceptible to helium-associated damage. In contrast, low-angle random boundaries and twin boundaries appeared to be strongly resistant to degradation from the combined effects of helium and welding.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Emulation of neutron-irradiated microstructure of austenitic 21Cr32Ni model alloy using dual-ion irradiation

Here, in this study, the capability of heavy-ion irradiation to emulate neutron irradiation was demonstrated on an austenitic 21Cr32Ni type ternary model alloy. The model alloy used in this study is chemically analogous but compositionally simpler than of alloy 800H, which is a candidate austenitic Ni alloy which has been proposed for use in Generation IV reactors. The microstructure of the 21Cr32Ni model alloy irradiated in the BOR-60 fast reactor to 17.1 dpa and 35 dpa at ~380°C was characterized using transmission electron microscopy (TEM). The 17.1 dpa BOR-60 irradiated microstructure was then compared with the microstructure of the same material developed under dual-ion (DI) irradiation using various He/dpa ratios between 0.1 and 16.6 appm He/dpa in the temperature range of 430°C-500°C. The results showed that both neutron and DI irradiation of 21Cr32Ni model alloy produced dislocations in the form of a dislocation network as well as {111}-type faulted dislocation loops, cavities, and radiation-induced Ni enrichment at radiation-induced sinks. When the dose and the He/dpa ratio were kept similar to those in neutron irradiation, DI irradiation of the 21Cr32Ni model alloy at 460°C resulted in over-nucleation of small cavities and in a high density of faulted dislocation loops compared to those observed in the fast-neutron irradiated alloy of the same heat irradiated at ~380°C. The optimal condition for reproducing the neutron-irradiated microstructure was DI irradiation at 460°C and 0.1 appm He/dpa. In that case, the faulted loop and cavity size distributions in the BOR-60 irradiated 21Cr32Ni model alloy samples closely matched with those measured in the DI irradiated 21Cr32Ni model alloy sample. The fact that the He/dpa is an order of magnitude smaller than the helium generation rate for fast neutron irradiation, stops over nucleation and allows for the development of a similar microstructure as for neutron irradiation.

21Cr32Ni model alloy↗
DOE OSTI2022

Transmission electron microscopy study of a high burnup U-10Zr metallic fuel

To support the development of U-10 wt.% Zr (U-10Zr) metallic fuel for Gen IV sodium-cooled fast reactors, we analysed a solid, Na-bonded, U-10Zr (by weight percent) fuel cross section that was irradiated to a burnup of ~ 12.4 % at.% at the Fast Flux Test Facility (FFTF). Advanced characterization techniques, including site specific sample preparation by focused ion beam (FIB) and phase/chemical determination by transmission electron microscopy (TEM), were used to reveal the constituent redistribution of Zr, characterize the fuel phases and the secondary phases (such as solid fission products) present at the end of life. It is shown that the fuel pin cross section is divided into three major concentric zones: a Zr-rich central region, a Zr-lean intermediate region, and a Zr intermediate peripherical region. The phase characterization revealed that the irradiation environment enhanced the development and stabilization of phases not predicted by the standard equilibrium U-Zr phase diagrams. Comparing the current results with the ones from previous studies, it is reaffirmed that the irradiation temperature and the time spent in the reactor, rather than the fuel burnup, are the two factors that most influence the formation of redistribution zones and their extension along the fuel cross section. Various solid fission products precipitated inside the fission gas pores, such as lanthanides, ZrRu, BaTe, CsI, and Ba and Sr oxides. Here, this study provides unprecedented nanoscale understandings in the U-10Zr fuel system that may benefit fuel performance modelling and advanced fuel development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Irradiation Effects on Stability of δ-UZr2 phase in U-50 wt% Zr Alloy

U-50wt%Zr is a candidate metallic nuclear fuel with potential application in light water reactors due to its excellent thermal properties and high radiation tolerance. The Zr-rich UZr fuels possess greater swelling resistance and fission gas release characteristics compared with U-rich UZr fuels. In this current study, the δ-phase U-50wt%Zr is proton irradiated at room temperature to 1 displacement per atom (dpa) to provide insights on phase stability under irradiation conditions. High resolution characterization of Transmission Electron Microscopy (TEM) and Atom Probe Tomography (APT) characterization techniques are used to elucidate microstructural changes due to irradiation. TEM and APT results show highly oriented bcc β-Zr-rich platelet precipitates nucleating adjacent to α-U phases inside the UZr 2 matrix. Formation of this platelet morphology is characteristic of Widmänstatten structure which can be attributed to a variety of factors such as differences in thermal expansion coefficient between the phases, grain size, alloy composition, and cooling rate. The phases present are distinctly different than those observed through in situ annealing, but irradiation accelerates diffusion and phase separation kinetics. These microstructural changes in U-50wt%Zr are different from those achieved by pure thermodynamic or high temperature heavy ion irradiation experiments. Finally, our work, together with previous ones, highlight the necessity to study the U-Zr phase diagram under non-equilibrium thermodynamics conditions to support this material's deployment as a viable nuclear fuel form.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Early self-organization of fission gas bubble superlattice formation in neutron-irradiated monolithic U-10Mo fuels

Self-organization of defect superlattices in far-from-equilibrium systems presents a promising way to mitigate swelling concerns in nuclear materials. The gas bubble superlattice (GBS) is a highly ordered, three-dimensional complex defect structure that can retain fission gasses in Uranium-Molybdenum (U-Mo) fuels. Transmission electron microscopy (TEM) investigation of monolithic U-10Mo fuel irradiated to 1.15 × 10 21 fissions/cm 3 and 1.30 × 10 21 fissions/cm 3 revealed that early-stage ordering preferentially occurs at the grain boundaries (GB) and that the critical bubble size for complete ordering is ~3 nm. Once formed at the GB, the GBS extends towards the grain interior; however, the spread in distance from the GB varies likely depending on the type and strength of the GB sink. TEM results also showed a possible correlation between the growth and evolution of the intragranular disordered bubbles and large dislocation networks. The fission product distribution in and outside of the GBS was also investigated confirming the presence of xenon in the GBS, as well as other fission products including cesium, barium, lanthanum, and cerium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

The role of UC inclusions in the development of fission gas bubble superlattice neutron-irradiated monolithic U-10Mo fuels

Uranium Carbide (UC) inclusions are the most prevalent impurities in Uranium-Molybdenum (U-Mo) fuel and are considered undesirable because they could potentially affect fuel performance. This work revealed that, like grain boundaries (gBs), UC inclusions could help facilitate the formation of the fission gas bubble superlattice (GBS). The GBS is a highly organized complex defect structure that can effectively store fission gases, thereby inhibiting fuel swelling. Transmission electron microscopy (TEM) showed that GBS self-organization can initiate at the UC/U-Mo interfaces in U-10Mo fuel irradiated to low fission density. Furthermore, this study also revealed that the UC boundary in U-10Mo irradiated to low fission density is wavy and periodic in morphology and that GBS formation is semi-coherent with the UC boundary. Because the initiation of GBS occurs at gBs and UC/U-Mo interfaces, the fission gas inventory is always highest at those regions compared to the U-Mo grain interior. Consequently, at higher fission densities, it is likely that high burnup structure (HBS) development via grain refinement will begin at gBs and UC/U-Mo interfaces.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Flash electropolishing of BCC Fe and Fe-based alloys

The preparation of transmission electron microscopy (TEM) samples is a critical step in the characterization of materials, and the focused ion beam (FIB) technique is a commonly used method. However, a significant limitation of this technique is the FIB-induced damages on the foil surfaces, which can obscure the real features of interest, particularly in radiation effects studies. To overcome this limitation, this study presents a detailed description of the flash electropolishing technique, which can be used to remove the FIB damage from samples. The flash electropolishing technique has been successfully applied to a range of materials, including Fe, Fe-based model alloys, commercial Fe-Cr alloys, and advanced Fe-Cr alloys, both in their as-received and ion-irradiated states. Furthermore, the parameters used for Fe-Cr model alloys can be adjusted for commercial and advanced alloys with minimal modifications. Further, the study also examined the effects of electropolishing variables, such as perchloric acid concentration, electropolishing temperature, Cr concentration, and voltage. Qualitatively, a general trend and scoping test strategy is explored in our experiments. Overall, the flash electropolishing technique offers a promising solution to the challenges posed by FIB-induced damages in the preparation of TEM samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural characterization of U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln

Antimony is being investigated as a potential additive to metallic fuel to control fuel-cladding chemical interactions (FCCI). The most detrimental elements involved in FCCI are fission product lanthanides, leading to brittle intermetallics and low melting eutectic phases. Previous investigations of Sb as an additive focused on U-10Zr, in wt. %, as the fuel. The current investigation expands that to include Pu in the fuel. Here, two alloys, U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln (wt. %, Ln=53Nd-25Ce-16Pr-6La) have been investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to characterize the fuel as-cast microstructure and the microstructure after introduction of lanthanides. Sb reacts with Zr initially, forming Zr 2 Sb and Zr 5 Sb 3 , with as much as 20 at. % interstitial Pu present. In the presence of lanthanides, Sb forms Ln 4 Sb 3 with the lanthanides, containing ~14 at. % Pu. The Pu is substitutional for the lanthanides in the crystal lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Defect-specific strength factors and superposition model for predicting strengthening of ion irradiated Fe18Cr alloy

Here, a high-purity binary alloy Fe18Cr was subjected to heavy-ion irradiation in order to provide improved understanding of the irradiation effect on radiation hardening associated with dislocation loop and network formation, α’ precipitation. The specimens were irradiated with 8 MeV Fe ions (~2 μm ion range) to midrange doses of 0.37 and 3.7 dpa at 300, 350 and 450 °C using dose rates of ~10 –5 –10 –3 dpa/s. Nanoindentation testing was performed to extract the bulk equivalent hardness at low depth from these ion irradiated specimens. High-quality transmission electron microscopy (TEM) images were acquired by utilizing a flash electropolishing method on the Focused Ion Beam (FIB) prepared liftouts. An accurate calculation of the strength factor was provided based on detailed TEM characterization of the irradiated microstructures. A newly refined hardening superposition method was applied to combine the strengthening components from each microstructure. The good agreement between microstructure predicted strength and measured strength further demonstrated the fidelity to use hardening model to quantify the mechanical properties of ion irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of W-SiC compositionally graded films as a divertor material

W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. Here, this study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Comparison of hardening and microstructures of ferritic/martensitic steels irradiated with fast neutrons and dual ions

Ferritic/martensitic steels T91 and HT9 were irradiated with neutrons (BOR-60 reactor) and dual ions (9 MeV Fe 3+ and 3.42 MeV energy degraded He 2+ ) from 369 to 520 °C and damage levels of 16.6 to 72 dpa to quantify the possibility of using ion irradiation to simulate neutron irradiation in terms of microstructures and mechanical properties. Nanoindentation testing was performed to obtain the bulk equivalent hardness of the dual-ion irradiated samples. For the neutron irradiated samples, both nanoindentation and Vickers hardness testing were conducted. Transmission Electron Microscopy (TEM) characterizations of the cavities, dislocation loops and precipitates were conducted to account for the strengthening contribution of each microstructure element. The good agreement between the microstructure-predicted (dispersed barrier hardening) and measured strength of the irradiated specimens demonstrated the accuracy of the strengthening model and the nanoindentation tests. Furthermore, the comparison of mechanical property and microstructure changes in ion and neutron irradiated structural materials indicated that ion irradiation replicated many neutron irradiation features. However, a single 70 °C temperature shift is insufficient to match all complex microstructures of neutron vs. ion irradiation over the irradiation temperature range of 369–520 °C.

36 MATERIALS SCIENCE↗