Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transonic Dynamics Tunnel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effects of spoiler surfaces on the aeroelastic behavior of a low-aspect-ratio rectangular wing

An experimental research study to determine the effectiveness of spoiler surfaces in suppressing flutter onset for a low-aspect-ratio, rectangular wing was conducted in the Langley Transonic Dynamics Tunnel (TDT). The wing model used in this flutter test consisted of a rigid wing mounted to the wind-tunnel wall by a flexible, rectangular beam. The flexible beam was connected to the wing root and cantilever mounted to the wind-tunnel wall. The wing had a 1.5 aspect ratio based on wing semispan and a NACA 64A010 airfoil shape. The spoiler surfaces consisted of thin, rectangular aluminum plates that were vertically mounted to the wing surface. The spoiler surface geometry and location on the wing surface were varied to determine the effects of these parameters on the classical flutter of the wing model. Subsonically, the experiment showed that spoiler surfaces increased the flutter dynamic pressure with each successive increase in spoiler height or width. This subsonic increase in flutter dynamic pressure was approximately 15 percent for the maximum height spoiler configuration and for the maximum width spoiler configuration. At transonic Mach numbers, the flutter dynamic pressure conditions were increased even more substantially than at subsonic Mach numbers for some of the smaller spoiler surfaces. But greater than a certain spoiler size (in terms of either height or width) the spoilers forced a torsional instability in the transonic regime that was highly Mach number dependent. This detrimental torsional instability was found at dynamic pressures well below the expected flutter conditions. Variations in the spanwise location of the spoiler surfaces on the wing showed little effect on flutter. Flutter analysis was conducted for the basic configuration (clean wing with all spoiler surface mass properties included). The analysis correlated well with the clean wing experimental flutter results.

Cole, Stanley R.↗
NASA NTRS1963

Investigation of Propeller-power-plant Autoprecession Boundaries for a Dynamic-aeroelastic Model of a Four-engine Turboprop Transport Airplane

A flexibly mounted aircraft engine may under certain conditions experience a self-excited whirling instability involving a coupling between the gyroscopic and aerodynamic forces acting on the propeller, and the inertial, elastic, and damping forces contributed by the power plant, nacelle, and wing. This phenomenon has been called autoprecession, or whirl instability. An experimental investigation was made in the Langley transonic dynamics tunnel at Mach numbers below 0.3 to study some of the pertinent parameters influencing the phenomenon. These parameters included propeller rotational speed, stiffness of the power-plant assembly in the pitch and yaw planes and the ratio of pitch stiffness to yaw stiffness, structural damping of the power-plant assembly in the pitch and yaw planes, simulated fuel load in the wings, and the location and number of autoprecessing powerplant assemblies. A large dynamic-aeroelastic model of a four-engine turboprop transport airplane mounted on a vertical rod in a manner which provided several limited body degrees of freedom was used in the investigation. It was found that the boundary for autoprecession decreased markedly with Increasing proreduction of power-plant stiffness and/or damping, and to a lesser degree decreased with reduction of simulated fuel load in the wings. peller rotational speed generally lowered the autoprecession boundary. This effect was more pronounced as the stiffness was increased. An inboard power plant was found to be more susceptible to autoprecession than an outboard one. Combinations in which two or more power plants had the same level of reduced stiffness resulted in autoprecession boundaries considerably lower than that of a single power plant with the same level of reduced stiffness.

POWER PLANT↗
NASA NTRS1973

Status of two studies on active control of aeroelastic response

The application of active control technology to the suppression of flutter has been successfully demonstrated during two recent studies in the Langley transonic dynamics tunnel. The first study involved the implementation of an aerodynamic-energy criterion, using both leading- and trailing-edge controls, to suppress flutter of a simplified delta-wing model. Use of this technique has resulted in an increase in the flutter dynamic pressure of approximately 12 percent for this model at a Mach number of 0.9 Analytical methods used to predict the open- and closed-loop behavior of the model are also discussed. The second study, was conducted to establish the effect of active flutter suppression on a model of the Boeing B-52 Control Configured Vehicle (CCV). Some preliminary results of this study indicate significant improvements in the damping associated with the critical flutter mode.

Abel, I.↗
NASA NTRS1974

Investigation of the effect of hub support parameters on two-bladed rotor oscillatory loads

The results are presented of a test program and analysis to investigate the effects of inplane hub support parameters on the oscillatory chordwise loads of a two-bladed teetering rotor. The test program was conducted in two phases. The first consisted of a shake test to define the impedance of a number of test configurations as a function of frequency. The second phase was the test of these configurations in the NASA-Langley transonic dynamics tunnel. The test showed that the one-per-rev inplane bending moments could be changed by a factor of 2.0 as a function of the pylon configuration at the same aerodynamic operating condition. The higher harmonic inplane, flapwise, and torsional bending moments, and pitch link axial loads were not affected by changes in inplane hub impedance. The maximum inplane loads occurred for the pylon configuration with the minimum spring rate and maximum inertia.

Lee, C. D.↗
NASA NTRS1974

Status of two studies on active control of aeroelastic response at NASA Langley Research Center

The application of active control technology to the suppression of flutter was successfully demonstrated during two recent studies in the Langley transonic dynamics tunnel. The first study involved the implementation of an aerodynamic-energy criterion, using both leading- and trailing-edge controls, to suppress flutter of a simplified delta-wing model. Use of this technique resulted in an increase in the flutter dynamic pressure of approximately 12 percent for this model at a Mach number of 0.9. Analytical methods used to predict the open- and closed-loop behavior of the model are also discussed. The second study, which is a joint effort with the Air Force Flight Dynamics Laboratory, was conducted to establish the effect of active flutter suppression on a model of the Boeing B-52 Configured Vehicle (CCV). Some preliminary results of this study indicate significant improvements in the damping associated with the critical flutter mode.

Abel, I.↗
NASA NTRS1974

Experimental and analytical studies in tilt-rotor aeroelasticity

An overview of an experimental and analytical research program underway for studying the aeroelastic and dynamic characteristics of tilt-rotor VTOL aircraft is presented. Selected results from several investigations of scaled models in the transonic dynamics tunnel, as well as some results from a test of a flight-worthy proprotor in the full-scale wind tunnel are shown and discussed with a view toward delineating various aspects of dynamic behavior peculiar to proprotor aircraft. Included are such items as proprotor/pylon stability, whirl flutter, gust response, and blade flapping. Theoretical predictions are shown to be in agreement with the measured stability and response behavior.

Kvaternik, R. G.↗
NASA NTRS1974

A transonic study of active flutter suppression based on an aerodymamic energy concept

The application of active control technology to the suppression of flutter has been successfully demonstrated in the Langley transonic dynamics tunnel. This study involved the implementation of an aerodynamic-energy criterion to suppress flutter of a simplified delta-wing model. Use of this technique with both leading- and trailing-edge active controls has resulted in an increase in dynamic pressure of 22% above the basic wing flutter point and with only a trailing-edge active control has resulted in an increase in dynamic pressure of 30% above the basic wing flutter point at a Mach number of 0.9. Analytical methods used to predict the open- and closed-loop behavior of the model are also discussed.

Sandford, M. C.↗
NASA NTRS1974

Experimental and analytical studies in tilt-rotor aeroelasticity

An overview of an experimental and analytical research program for studying the aeroelastic and dynamic characteristics of tilt-rotor VTOL aircraft is presented. Selected results from several investigations of scaled models in the Langley transonic dynamics tunnel as well as some results from a test of a flight-worthy prop rotor in the NASA Ames full-scale wind tunnel are shown and discussed with a view toward delineating various aspects of dynamic behavior peculiar to prop rotor aircraft. Included are such items as prop rotor pylon stability, whirl flutter, gust response, and blade flapping. Theoretical predictions, based on analyses developed at Langley, are shown to be in agreement with the measured stability and response behavior.

Kvaternik, R. G.↗
NASA NTRS1975

Development and demonstration of a flutter-suppression system using active controls

The application of active control technology to suppress flutter was demonstrated successfully in the transonic dynamics tunnel with a delta-wing model. The model was a simplified version of a proposed supersonic transport wing design. An active flutter suppression method based on an aerodynamic energy criterion was verified by using three different control laws. The first two control laws utilized both leading-edge and trailing-edge active control surfaces, whereas the third control law required only a single trailing-edge active control surface. At a Mach number of 0.9 the experimental results demonstrated increases in the flutter dynamic pressure from 12.5 percent to 30 percent with active controls. Analytical methods were developed to predict both open-loop and closed-loop stability, and the results agreed reasonably well with the experimental results.

Sandford, M. C.↗
NASA NTRS1976

Geared-elevator flutter study

An experimental and analytical study was made of the transonic flutter characteristics of a supersonic transport tail assembly model having an all-movable, horizontal tail with a geared elevator. Two model configurations, namely, one with a gear-elevator (2.8 to 1.0 gear ratio) and one with locked-elevator (1.0 to 1.0 gear ratio), were flutter tested in the Langley transonic dynamics tunnel with an empennage cantilever-mounted on a sting. The geared-elevator configuration fluttered experimentally at about 20% higher dynamic pressures than the locked-elevator configuration. The experimental flutter dynamic pressure boundaries for both configurations were nearly flat over a Mach number range from 0.9 to 1.1. Flutter calculations (mathematical models) were made for the geared-elevator configuration using three subsonic lifting-surface methods. In one method, the elevator was treated as a discrete surface, and in the other two methods, the stabilizer and elevator were treated as a single warped-surface with the primary difference between these two methods being in the mathematical implementation used. A comparison of the experimental and analytical results shows that the discrete-elevator method predicted best the experimental flutter dynamic pressure level. However, the single warped-surface methods predicts more closely the experimental flutter frequencies and Mach number trends.

Ruhlin, C. L.↗
NASA NTRS1976

A review of some tilt-rotor aeroelastic research at NASA-Langley

An overview of an experimental and analytical research program conducted within the Aeroelasticity Branch of the NASA Langley Research Center for studying the aeroelastic and dynamic characteristics of tilt-rotor VTOL aircraft is presented. Selected results from several joint NASA/contractor investigations of scaled models in the Langley transonic dynamics tunnel are shown and discussed with a view toward delineating various aspects of dynamic behavior peculiar to proprotor aircraft. Included are such items as proprotor/pylon stability, whirl flutter, gust response, and blade flapping. Theoretical predictions, based on analyses developed at Langley, are shown to be in agreement with the measured stability and response behavior.

Kvaternik, R. G.↗
NASA NTRS1976

Correlation of full-scale helicopter rotor performance in air with model-scale Freon data

An investigation was conducted in a transonic dynamics tunnel to measure the performance of a 1/5 scale model helicopter rotor in a Freon atmosphere. Comparisons were made between these data and full scale data obtained in air. Both the model and full scale tests were conducted at advance ratios between 0.30 and 0.40 and advancing tip Mach numbers between 0.79 and 0.95. Results show that correlation of model scale rotor performance data obtained in Freon with full scale rotor performance data in air is good with regard to data trends. Mach number effects were found to be essentially the same for the model rotor performance data obtained in Freon and the full scale rotor performance data obtained in air. It was determined that Reynolds number effects may be of the same magnitude or smaller than rotor solidity effects or blade elastic modeling in rotor aerodynamic performance testing.

Yeager, W. T., Jr.↗
NASA NTRS1976

Some applications of the NASTRAN level 16 subsonic flutter analysis capability

The Level 16 flutter analysis capability was applied to an aspect-ratio-6.8 subsonic transport type wing, an aspect-ratio-1.7 arrow wing, and an aspect-ratio-1.3 all movable horizontal tail with a geared elevator. The transport wing and arrow wing results are compared with experimental results obtained in the Langley transonic dynamic tunnel and with other calculated results obtained using subsonic lifting surface (kernel function) unsteady aerodynamic theory.

Doggett, R. V., Jr.↗
NASA NTRS1977

F-16 flutter model studies with external wing stores

Results from transonic flutter model studies are presented. The flutter model was constructed to support the flutter prevention and clearance program from preliminary design through flight flutter tests. The model tests were conducted in the Langley transonic dynamics tunnel. The large full span free-flying model was shown to be an effective tool in defining airplane flutter characteristics by demonstrating freedom from flutter for most configurations and by defining optimum solutions for a few troublesome configurations.

Foughner, J. T., Jr.↗
NASA NTRS1980

Experimental and analytical transonic flutter characteristics of a geared-elevator configuration

The flutter model represented the aft fuselage and empennage of a proposed supersonic transport airplane and had an all movable horizontal tail with a geared elevator. It was tested mounted from a sting in the transonic dynamics tunnel. Symmetric flutter boundaries were determined experimentally at Mach numbers from 0.7 to 1.14 for a geared elevator configuration (gear ratio of 2.8 to 1.0) and an ungeared elevator configuration (gear ratio of 1.0 to 1.0). Gearing the elevator increased the experimental flutter dynamic pressures about 20 percent. Flutter calculations were made for the geared elevator configuration by using two analytical methods based on subsonic lifting surface theory. Both methods analyzed the stabilizer and elevator as a single, deforming surface, but one method also allowed the elevator to be analyzed as hinged from the stabilizer. All analyses predicted lower flutter dynamic pressures than experiment with best agreement (within 12 percent) for the hinged elevator method. Considering the model as mounted from a flexible rather than rigid sting in the analyses, had only a slight effect on the flutter results but was significant in that a sting related vibration mode was identified as a potentially flutter critical mode.

Ruhlin, C. L.↗
NASA NTRS1981

Experimental and analytical study on the flutter and gust response characteristics of a torsion-free-wing airplane model

Experimental data and correlative analytical results on the flutter and gust response characteristics of a torsion-free-wing (TFW) fighter airplane model are presented. TFW consists of a combined wing/boom/canard surface and was tested with the TFW free to pivot in pitch and with the TFW locked to the fuselage. Flutter and gust response characteristics were measured in the Langley Transonic Dynamics Tunnel with the complete airplane model mounted on a cable mount system that provided a near free flying condition. Although the lowest flutter dynamic pressure was measured for the wing free configuration, it was only about 20 deg less than that for the wing locked configuration. However, no appreciable alleviation of the gust response was measured by freeing the wing.

Murphy, A. C.↗
NASA NTRS1982

Static and unsteady pressure measurements on a 50 degree clipped delta wing at M = 0.9

Static and unsteady pressures were measured on a 50.45 degree clipped delta wing in the Langley Transonic Dynamics Tunnel with Freon as the test medium. Data taken at M = 0.9 is presented for static and oscillatory deflections of the trailing edge control surface and for the wing in pitch. Comparisons of the static measured data are made with results computed using the Bailey-Ballhaus small disturbance code.

Hess, R. W.↗
NASA NTRS1983

Parametric tip effects for conformable rotor applications

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on aeroelasticity conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and three tip designs were tested on the torsionally soft blades. The designs incorporated a systematic variation in three geometric parameters: sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. Based on the test results, tip parameter variations generated significant rotor performance and loads difference for both baseline and torsionally soft blades. Azimuthal variation of elastic twist generated by the tip parameters strongly correlated with rotor performance and loads, but the magnitude of advancing blade elastic twist did not correlate.

Mantay, W. R.↗