Search NASA⌕ Search

SEARCH · Search NASA

Results for “W(OF)2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Validation of heat transport modeling using directly driven beryllium spheres

Recent experiments involving directly driven beryllium spheres are reported. Plasma conditions are measured using Thomson scattering with the probe beam pointed 200, 300, and 400 μ m from the surface of the sphere. Laser coupling is assessed using calorimeters that collect scattered light placed at various locations within the target chamber. Laser intensities of 1 0 14 W / c m 2 and 2.5 × 1 0 14 W / c m 2 are chosen to minimize unmodeled laser-plasma interactions (LPIs) that lead to laser-target decoupling. Two-dimensional simulations are compared to the interpreted data using the radiation-hydrodynamics code Lasnex. Heat transport is simulated using flux-limited Spitzer–Harm with both high ( f = 0.15) and low ( f = 0.03) flux limiters and the Schurtz–Nicolai-Busquet (SNB) model. At 1 0 14 W / c m 2 , all three heat transport models agree well with the measurement, demonstrating that the heat flux is local at low intensities near the measurement locations. At 2.5 × 1 0 14 W / c m 2 , the SNB and high flux model roughly match the plasma conditions but predict 2% uncoupled light compared to 10% measured. Additionally, the use of drive multipliers to match the measured coupled light does not alter the agreement between measured and simulated plasma conditions, suggesting that decoupling due to LPI is unlikely to alter this agreement. The low flux model cannot match the plasma conditions and results in 19% scattered light. The use of a resonant absorption model can be used to bring the simulated scattered light into agreement, but the simulated plasma conditions are still in disagreement with the measurement. For this reason, the low flux model is rejected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

The Incredible Lightness of Water Vapor

The molar mass of water vapor is much less than that of dry air. This makes a moist parcel lighter than a dry parcel of the same temperature and pressure. This effect is referred to as the vapor buoyancy effect and has often been overlooked in climate studies. We propose that the vapor buoyancy effect increases Earth’s outgoing longwave radiation (OLR) and that this negative radiative effect increases with warming, stabilizing Earth’s climate. We illustrate this mechanism in an idealized tropical atmosphere, where there is no horizontal buoyancy gradient in the free troposphere. Temperature increases toward dry atmosphere columns to compensate the reduced vapor buoyancy, increasing OLR by O(1 W m −2 ) at the reference climate. In warmer climates, the temperature difference between moist and dry columns would increase as a result of increasing atmospheric water vapor, leading to enhanced radiative effect and thereby stabilizing Earth’s climate. We estimate that this feedback strength is about O(0.2 W m −2 K −1 ) in the idealized atmosphere, which compares to cloud feedback and surface albedo feedback in the current climate. We further show evidence from observations and real-gas radiative transfer calculations for a significant radiative effect of vapor buoyancy in the tropical atmosphere.

Yang, Da↗
DOE OSTI2024

From Fundamental Interfacial Reaction Kinetics to Macroscopic Current–Voltage Characteristics: Case Study of Solid Acid Fuel Cell Limitations and Possibilities

The unique properties of solid acid electrolytes, in particular CsH 2 PO 4 , are in many ways ideal for fuel cell operation. However, the technology is constrained by high cathode overpotentials. Here a simplified cathode geometry is employed to obtain the fundamental electrochemical parameters (exchange current density and charge transfer coefficient) describing the oxygen reduction reaction (ORR) at the CsH 2 PO 4 -Pt-gas interface. The parameters are incorporated into a 1D model of the voltage–current characteristics of realistic SAFC cathodes, which reproduced the measured polarization behavior of such cathodes without recourse to fitting adjustable parameters. Following this validation, the model is utilized to evaluate the impact of changes to cathode properties, microstructure, and operating conditions. Of these, the charge transfer coefficient, measured to have a value of ≈0.6 for ORR on Pt in the SAFC cathode environment, is found to have the greatest impact on power output. Nevertheless, even without material modifications, a combination of microstructural and operational modifications are identified with projected performance metrics meeting Department of Energy targets (0.8 V at 300 mA cm –2 , and peak power density of 1 W cm –2 ), albeit at high Pt loadings. However, the analysis indicates that truly meaningful advances will likely necessitate the discovery of alternative ORR catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Conformal high-entropy oxide coatings enable fast and durable surface oxygen reactions

Developing active and durable air electrodes for efficient oxygen reactions is challenging for protonic ceramic cells (PCCs), especially at temperatures below 550°C. Here, in this study, we report a rationally designed conformal coating with a high-entropy PrNi 0.2 Mn 0.2 Co 0.2 Fe 0.2 Cu 0.2 O 3−δ (PNMCFC) perovskite structure on the surface of a state-of-the-art PrBaCo 2 O 5+δ (PBC) air electrode. The formed hybrid air electrode (PNMCFC-PBC) shows faster surface oxygen kinetics and a more stable phase structure in high-humidity air than the bare PBC electrode. Further density functional theory calculations suggest that the conformal coating mitigates Ba segregation at the interface and improves oxygen-related reactions, enhancing overall stability and electrocatalytic performance. The cells with the developed hybrid electrodes show encouraging electrochemical performance at 550°C: a polarization resistance of 0.72 Ω cm 2 , a peak power density of 1.30 W cm −2 , an electrolysis current density of −1.36 A cm −2 at 1.3 V, and reasonable operating stabilities (∼200 h at 550°C).

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Energetics of silicon in the bulk and near surfaces of tungsten: a first-principles study

Abstract Siliconization of the tokamak walls is a candidate method to improve plasma confinement in fusion tokamaks containing tungsten plasma facing components (W PFCs). To understand the interactions of silicon (Si) with W, the Si behavior in bulk W, and near three low-index W surfaces ((100), (110) and (111)) has been investigated using first-principles density functional theory. In bulk W, Si interstitial atoms have a low solution ability and high mobility, and Si atoms can be strongly trapped by W vacancies. The interaction between two Si adatoms is responsible for the stability of adatom superstructures on W surfaces, consistent with previous experimental observation (Tsong and Casanova 1981 Phys. Rev. Lett. 47 113). Although the coverage dependence of Si adsorption and diffusion energetics on surfaces is related to surface orientation, the W(110) surface has lower Si adsorption affinity and higher Si diffusivity than either the W(111) or W(100) surfaces. The most stable Si adatom superstructure on W surfaces is: square c(2 × 2) pattern on W(100) covered with 0.5 ML Si; rectangular c(4 × 2) pattern on W(110) with 0.25 ML Si; and rhombus p(1 × 1) pattern on W(111) with 1 ML Si. The coverage dependence of Si mobility on/toward W surfaces is generally related to the stability of the Si superstructures as a function of coverage on each surface. Interestingly, Si adatoms prefer to transport below the surface and into W subsurface by an exchange mechanism with W atoms, indicating the likelihood of epitaxial growth of W silicide layers on W surfaces during the operation of W PFCs.

Yang, L. (ORCID:0000000322166071)↗
DOE OSTI2023

A novel 3-D pulsating heat pipe module for high heat-flux applications

This study proposed a novel pulsating heat pipes (PHP) for high-flux thermal module. According to the open literature, the maximum value of the heat flux is 23.7 W∙cm –2 handled by PHP, which is far behind industry requirements. Therefore, the present study proposes a novel 3D PHP suitable for high heat-flux applications. The PHP were experimentally tested for different working fluids, including methanol and water. Furthermore, the experiments were performed to analyze the influence of various operating parameters, such as filling ratio (25–60%), heat load (100–800 W), and air flow rate 100–250 cubic feet per minute (CFM). In this work, the results showed that this PHP can sustain a heat flux up to 70 W∙cm –2 with the maximum case temperature under 80 °C, which is approximately three times higher than the available literature. Furthermore, the performance of the PHP module was compared against the commercial module with wicked heat pipe. The PHP exhibited about 7% higher heat dissipation compared to the commercial module. Since the proposed module uses simple copper tubes in its construction over the wicked structure used in commercial module, the novel 3D PHP module provides additional economic and mass production capability.

3D pulsating heat pipe↗
DOE OSTI2021

Features of ion generation by a picosecond laser in the range of 10 11 –10 13 W cm -2 power densities

Picosecond lasers (ps-lasers) have significant advantages for the generation of low charge state ions compared to nanosecond lasers because the influence of heat conductivity on a solid target is almost negligible in the case of ps-laser ablation for laser pulse durations less than 10 ps. However, there is no comprehensive data on ion yields for different elements and target irradiation conditions for laser power densities at the target surface around and below 10 13 W cm –2 , which is of interest to our study of such plasmas as a source of low charge state ions for various applications, particularly for external injection of those ions into an Electron Beam Ion Source (EBIS). We investigated ion generation from Al, Ti, Cu, Nb and Ta target elements by a ps-laser with power densities in the range of 10 11 –10 13 W cm –2 at the target surface. A ps-laser with 1.27 mJ maximum energy within an 8 ps pulse and repetition rate up to 400 Hz has been used to generate a laser-ablated plasma. Dependencies of ion current versus time, total charge of registered ions as well as ion kinetic energy distributions are characterized using a Faraday cup. Significant difference in ion current dynamics between first, second and following shots onto the same target spot was found for all five target elements. The total charge of ions registered by the Faraday cup increases linearly with increasing laser pulse energy and is almost independent of the target element and number of shots onto the same target spot for all five target elements studied. The results obtained give us a basis for specification and design of the source of low charge state ions for external injection into EBIS.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Laser–plasma amplification of an ultrabroadband laser pulse to 0.3 TW

Producing on-target laser intensities much greater than 10 23 W cm −2 with current laser technologies is a roadblock to accessing new regimes of physics such as strong-field quantum electrodynamics. Laser–plasma amplifiers show promise to realize these intensities by augmenting the final amplifier and compressor in traditional chirped-pulse-amplification architectures with a plasma-based amplification and compression stage that operates at a much higher damage threshold. Here we demonstrate amplification of an ultrabroadband (>60 nm) pulse in a laser–plasma Raman amplifier. We directly amplified seed intensities up to 3.7 × 10 15 W cm −2 and measured efficiencies up to 8.7%. Single-shot SPIDER measurements show a factor-of-2 reduction in the amplified pulse duration with final powers up to 0.3 TW, a 10× improvement over previous results. Final pulse durations of 64 fs are measured. Energy transfers greater than 220 mJ from the picosecond pump into the seed result in a 30× energy amplification of a 7.6 mJ seed. These results set the stage for a compact plasma afterburner based on Raman amplification that could extend the scientific capability of existing petawatt-class laser facilities to enable experiments at the intensity frontier.

Shaw, J. L. [Univ. of Rochester, NY (United States↗
DOE OSTI2024

Field‐representative evaluation of PID‐polarization in TOPCon PV modules by accelerated stress testing

Abstract Potential‐induced degradation‐polarization (PID‐p) can reduce module power, but how to project the extent to which PID‐p may occur in field conditions considering the factors of system voltage, condensed moisture, temperature, and illumination has not been clarified. Using tunnel oxide passivated contact (TOPCon) modules, this work demonstrates a method to test full‐size crystalline silicon PV modules for PID‐p to provide field‐representative results. In initial screening tests with positive or negative 1000 V electrical bias applied at 60°C for 96 h using Al foil electrodes on the glass surfaces, the module type exhibited reversible PID‐p only on the front face when the cell circuit was in negative voltage potential. No PID was detected on the rear after testing in either polarity. We then evaluated the PID‐p sensitivity on the front side under different UV irradiances while maintaining the glass surface wet to estimate real‐world susceptibility to PID‐p. The magnitude of the observed behavior was fit using a previously developed charge transfer and depletion by light model. Whereas power loss with −1000 V applied to the cell circuit at 60°C for 96 h in the dark was about 30%, testing the module front under 0.051 W·m −2 nm −1 at 340 nm UVA irradiation using fluorescent tubes, the mean degradation was only 3%. When the modules were tested in the dark for PID‐p with in situ dark current–voltage (I‐V) characterization, the thermal activation energy for degradation was 0.71 eV; for recovery in the dark, it was 0.58 eV. Whereas recovery from the degraded state at 60°C in the dark without voltage bias was 5% absolute in 38 h, rapid recovery of about 5% absolute was observed with 1000 W·s/m 2 exposure at 25°C using a flash tester.

14 SOLAR ENERGY↗
DOE OSTI2023

A New Class of Proton Conductors with Dramatically Enhanced Stability and High Conductivity for Reversible Solid Oxide Cells

Reversible solid oxide cells based on proton conductors (P-ReSOCs) have potential to be the most efficient and low-cost option for large-scale energy storage and power generation, holding promise as an enabler for the implementation of intermittent renewable energy technologies and the widespread utilization of hydrogen. Here, the rational design of a new class of hexavalent Mo/W-doped proton-conducting electrolytes with excellent durability while maintaining high conductivity is reported. Specifically, BaMo(W) 0.03 Ce 0.71 Yb 0.26 O 3-δ exhibits dramatically enhanced chemical stability against high concentrations of steam and carbon dioxide than the state-of-the-art electrolyte materials while retaining similar ionic conductivity. In addition, P-ReSOCs based on BaW 0.03 Ce 0.71 Yb 0.26 O 3-δ demonstrate high peak power densities of 1.54, 1.03, 0.72, and 0.48 W cm –2 at 650, 600, 550, and 500 °C, respectively, in the fuel cell mode. During steam electrolysis, a high current density of 2.28 A cm –2 is achieved at a cell voltage of 1.3 V at 600 °C, and the electrolysis cell can operate stably with no noticeable degradation when exposed to high humidity of 30% H 2 O at –0.5 A cm –2 and 600 °C for over 300 h. Altogether, this work demonstrates the promise of donor doping for obtaining proton conductors with both high conductivity and chemical stability for P-ReSOCs.

25 ENERGY STORAGE↗
DOE OSTI2020

Subcloud and Cloud-Base Latent Heat Fluxes during Shallow Cumulus Convection

Doppler and Raman lidar observations of vertical velocity and water vapor mixing ratio are used to probe the physics and statistics of subcloud and cloud-base latent heat fluxes during cumulus convection at the ARM Southern Great Plains (SGP) site in Oklahoma, United States. The statistical results show that latent heat fluxes increase with height from the surface up to ~0.8 Z i (where Z i is the convective boundary layer depth) and then decrease to ~0 at Z i . Peak fluxes aloft exceeding 500 W m −2 are associated with periods of increased cumulus cloud cover and stronger jumps in the mean humidity profile. These entrainment fluxes are much larger than the surface fluxes, indicating substantial drying over the 0–0.8 Z i layer accompanied by moistening aloft as the CBL deepens over the diurnal cycle. We also show that the boundary layer humidity budget is approximately closed by computing the flux divergence across the 0–0.8 Z i layer. Composite subcloud velocity and water vapor anomalies show that clouds are linked to coherent updraft and moisture plumes. The moisture anomaly is Gaussian, most pronounced above 0.8 Z i and systematically wider than the velocity anomaly, which has a narrow central updraft flanked by downdrafts. This size and shape disparity results in downdrafts characterized by a high water vapor mixing ratio and thus a broad joint probability density function (JPDF) of velocity and mixing ratio in the upper CBL. We also show that cloud-base latent heat fluxes can be both positive and negative and that the instantaneous positive fluxes can be very large (~10 000 W m −2 ). However, since cloud fraction tends to be small, the net impact of these fluxes remains modest.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

$In-situ$ synchrotron x-ray diffraction and thermal expansion of TiB2 up to ~3050 °C

There is an increasing interest in understanding the performance and properties of ultra-high temperature ceramics due to their high melting points (<3000 °C) that make them promising for extreme environment applications. In-situ high temperature X-ray diffraction experiments were performed on TiB 2 beads up to ~3050 °C. For these experiments, TiB 2 powders were fabricated into spherical beads via gel casting methods and densified in a high temperature graphite furnace. These sample beads were then levitated in a conical nozzle levitator with reducing atmosphere (3% H 2 -Ar) while being heated using a 400 W CO 2 laser. During levitation a collimated synchrotron X-ray source was used to perform in-situ, temperature-dependent structural characterizations. The anisotropic coefficients of thermal expansion of TiB 2 were characterized as a function of temperature up to ~3050 °C. Elucidation of these properties are critical for the advancement of TiB 2 ceramics and other transition metal di-borides for use in high temperature applications such as hypersonic platforms, nuclear reactors, and atmospheric re-entry.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Editors’ Choice—Uncovering the Role of Alkaline Pretreatment for Hydroxide Exchange Membrane Fuel Cells

Alkaline pretreatment is perceived as an essential step for high-performance hydroxide exchange membrane fuel cells (HEMFCs), but its exact function is not fully understood. Here we show that alkaline pretreatment is only necessary when carboxylates are generated from platinum- or palladium-catalyzed oxidation of primary alcohol solvents during membrane electrode assembly (MEA) fabrication. When alkaline pretreatment is needed, bicarbonates are a better choice than the most commonly used hydroxide bases. We further demonstrate that MEAs with Pt/Pd-free catalysts, which can be used in HEMFCs, exhibit a better performance without the alkaline pretreatment: a voltage of 0.64 V at 1.0 A cm −2 and a peak power density of 0.69 W cm −2 in H 2 /O 2 . The optimization or elimination of the alkaline pretreatment will simplify the fabrication process for fuel cells and thus reduces their manufacturing costs.

Shi, Lin↗
DOE OSTI2020

W-ZrC composites prepared by reactive melt infiltration of Zr 2 Cu alloy into binder jet 3D printed WC preforms

W-ZrC composites were successfully prepared by reactive melt infiltration (RMI) of stoichiometric and excess amounts of Zr 2 Cu into sintered and un-sintered WC preforms made from binder jet 3D printing. The focus of this work was to study the conversion of reactant powders and liquid infiltrant with varying preform density and infiltrant amount by controlling the processing time to reach high conversion yield while understanding the phase composition, microstructure, and hardness. To investigate the effect of time, the reactive melt infiltration was conducted at 1400 °C for 2, 4 and 8 h in a furnace with 96% Ar - 4% H2 gas atmosphere. The increase in reaction time from 2 to 8 h increased the W and W 2 C phase contents and decreased the ZrC phase content when using sintered WC preforms. Samples prepared from un-sintered WC preforms exhibited improved reactive melt infiltration compared to sintered samples, and there was no detectable W 2 C phase and nearly full consumption of WC. Similar to sintered WC samples, the content of W and ZrC phases increased with the increase in time from 2 to 8 h. The interfaces and phases at reaction interfaces were investigated using electron diffraction analysis and S/TEM-EDS to understand material stability; the phases were identified and consistent with XRD analysis. Additionally, there was no Cu present at the interfaces. Increasing the amount of infiltrant led to better reactive melt infiltration. In general, the hardness increased with reaction time and the highest Vickers hardness was found in the W-ZrC sample formed from sintered WC reacted with excess Zr 2 Cu. Finally, this research addresses the critical comparison of sintering and RMI time and shows that by using un-sintered samples for 8 h we are able to achieve W-ZrC composites with fewer undesired phases.

36 MATERIALS SCIENCE↗