SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low speed wind tunnel test on effects of horizontal tail geometry on longitudinal stability of orbiter shuttle
Results from the First AIAA Stability and Control Prediction Workshop are summarized in this paper. The workshop series was developed in support of three primary objectives: (1) to establish best practices for the prediction of stability and control derivatives using industry-standard Computational Fluid Dynamics (CFD) solvers, (2) to provide an impartial forum for evaluating the effectiveness of Reynolds-averaged-Navier-Stokes- and Detached-Eddy-Simulation-based modeling techniques, and (3) to identify areas in need of additional research and development. To address these objectives, the inaugural workshop focused on generating computational aerodynamic predictions for the ONERA version of the NASA/Boeing Common Research Model. The configuration includes the wing, body, horizontal tail, and a vertical tail designed by ONERA. While longitudinal wind tunnel test data for the model had been previously documented, unpublished lateral test data at small sideslip angles provided a unique opportunity for participants to generate blind computational predictions for wind tunnel data comparisons. Additional test cases included assessments of the Mach number effect on static lateral/directional stability and the impact of the wind tunnel sting on longitudinal stability. Participants were invited to generate solutions using two workshop-provided series of structured overset and unstructured grids, in addition to any participant custom grids of interest. Total and component-level breakdowns for the force and moment coefficients for each test case are presented, as well as sectional pressure distribution data on the wing and tail components, to assess the agreement between several different Reynolds-averaged Navier-Stokes CFD solvers.
A research effort of analysis and testing was conducted to investigate the ground resonance phenomenon of a soft in-plane hingeless rotor. Experimental data were obtained using a 9 ft. (2.74 m) diameter model rotor in hover and forward flight. Eight model rotor configurations were investigated. Configuration parameters included pitch flap coupling, blade sweep and droop, and precone of the blade feathering axis. An analysis based on a comprehensive analytical model of rotorcraft aerodynamics and dynamics was used. The moving block was used to experimentally determine the regressing lead lag mode damping. Good agreement was obtained between the analysis and test. Both analysis and experiment indicated ground resonance instability in hover. An outline of the analysis, a description of the experimental model and procedures, and comparison of the analytical and experimental data are presented.
Explore the source record for details and available documents.
Wind tunnel tests were conducted by Nielsen Engineering & Research (NEAR) and Rose Engineering & Research (REAR) in conjunction with the NASA Engineering & Safety Center (NESC) on a 6%-scale model of the Orion launch abort vehicle (LAV) configured with four grid fins mounted near the base of the vehicle. The objectives of these tests were to 1) quantify LAV stability augmentation provided by the grid fins from subsonic through supersonic Mach numbers, 2) assess the benefits of swept grid fins versus unswept grid fins on the LAV, 3) determine the effects of the LAV abort motors on grid fin aerodynamics, and 4) generate an aerodynamic database for use in the future application of grid fins to small length-to-diameter ratio vehicles similar to the LAV. The tests were conducted in NASA Ames Research Center's 11x11-foot transonic wind tunnel from Mach 0.5 through Mach 1.3 and in their 9x7-foot supersonic wind tunnel from Mach 1.6 through Mach 2.5. Force- and moment-coefficient data were collected for the complete vehicle and for each individual grid fin as a function of angle of attack and sideslip angle. Tests were conducted with both swept and unswept grid fins with the simulated abort motors (cold jets) off and on. The swept grid fins were designed with a 22.5deg aft sweep angle for both the frame and the internal lattice so that the frontal projection of the swept fins was the same as for the unswept fins. Data from these tests indicate that both unswept and swept grid fins provide significant improvements in pitch stability as compared to the baseline vehicle over the Mach number range investigated. The swept fins typically provide improved stability as compared to the unswept fins, but the performance gap diminished as Mach number was increased. The aerodynamic performance of the fins was not observed to degrade when the abort motors were turned on. Results from these tests indicate that grid fins can be a robust solution for stabilizing the Orion LAV over a wide range of operating conditions.
Hinge-moment, lift, and pressure-distribution measurements were made in the two-dimensional test section of the NACA stability tunnel on a blunt-nose balance-type aileron on an NACA 66,2-216 airfoil at speeds up to 360 miles per hour corresponding to a Mach number of 0.475. The tests were made primarily to determine the effect of speed on the action of this type of aileron. The balance-nose radii of the aileron were varied from 0 to 0.02 of the airfoil chord and the gap width was varied from 0.0005 to 0.0107 of the airfoil chord. Tests were also made with the gap sealed.
This report presents the results of wind tunnel tests to determine the effect of wing-tip shape and dihedral on some of the aerodynamic characteristics of Clark Y wings that affect the performance and lateral stability of airplanes. Force tests at several angles of yaw and rotation tests at zero yaw were made. From these tests the rates of change of rolling moment, yawing moment, and cross-wind force coefficients with angle of yaw and the rate of change of rolling moment coefficient with rolling were determined.
The Augmentor-Wing Jet STOL Research Aircraft has been developed and has started flight tests. The objectives of the program are to compare aerodynamic characteristics predicted from wind-tunnel data with data obtained in flight, to determine flight dynamic characteristics and limitations of the augmentor-wing concepts, and to contribute to the development of STOL design and operational criteria. Initial flight test results have shown that the aerodynamic characteristics are close to values predicted from wind-tunnel tests. The lateral-directional stability and control characteristics are satisfactory for research STOL missions with stability augmentation, but the longitudinal control require improvement. STOL take-off distance over 11 m is about 290 m, and landing approach speeds are between 60 and 65 knots. The investigation of the STOL operational and performance characteristics is continuing.
The paper presents highlights of a recent study which illustrates the application and analysis of dynamic stability parameters. More specifically, the investigation consisted of an evaluation of the effects of wing leading-edge modifications on the stalling and spinning characteristics of a single-engine general aviation research airplane. The results of the investigation illustrate how dynamic stability parameters measured in wind-tunnel tests are used to predict the spin resistance of this class of aircraft; and that autorotation criteria can be derived from the relationships which exist between static and dynamic aerodynamic characteristics.
With the recent interest in novel control effectors there is a need to determine the stability and control derivatives of new aircraft configurations early in the design process. These derivatives are central to most control law design methods and would allow the determination of closed-loop control performance of the vehicle. Early determination of the static and dynamic behavior of an aircraft may permit significant improvement in configuration weight, cost, stealth, and performance through multidisciplinary design. The classical method of determining static stability and control derivatives - constructing and testing wind tunnel models - is expensive and requires a long lead time for the resultant data. Wind tunnel tests are also limited to the preselected control effectors of the model. To overcome these shortcomings, computational fluid dynamics (CFD) solvers are augmented via automatic differentiation, to directly calculate the stability and control derivatives. The CFD forces and moments are differentiated with respect to angle of attack, angle of sideslip, and aircraft shape parameters to form these derivatives. A subset of static stability and control derivatives of a tailless aircraft concept have been computed by two differentiated inviscid CFD codes and verified for accuracy with central finite-difference approximations and favorable comparisons to a simulation database.
Wind tunnel tests were conducted to: (1) determine the static stability characteristics of the Shuttle Vehicle 5 configuration; (2) determine the effect on the Vehicle 5 aerodynamic characteristics of External Tank (ET) and Solid Rocket Booster (SRB) nose shape, SRB nozzle shroud flare angle, orbiter to tank fairing, and sting location; (3) provide flow visualization using thin film oil paint; and (4) determine rudder, body flap, and inboard and outboard elevon hinge moments. The mated vehicle model was mounted in three different ways: (1) the orbiter mounted on the balance with the SRB's attached to the tank and the tank in turn attached to the orbiter; (2) the tank mounted on the balance (with the sting protruding through the tank base) with the SRB's and orbiter attached to the tank, and (3) with the tank mounted on the balance and the balance in turn supported by a forked sting entering the nozzle of each SRB, extending forward into the SRB's then crossing over to the tank to provide a balance socket. Data were obtained for Mach numbers from 0.6 through 4.96 at angles-of-attack and -sideslip from -10 to 10 degrees.
Low speed wind tunnel tests of straight wing and delta wing configuration space shuttle booster models
An investigation was conducted in the 6- by 6-foot test section of the Langley stability tunnel on a modified Koppers Aeromatic wind-driven impeller-generator combination. This investigation consisted of a few fixed pitch tests and a series of variable pitch tests, The fixed pitch tests indicated that the impeller should operate between the blade-pitch angles of 20 and 32deg at the specified output of 11.7 kilowatts in order to remain within the specified rotational speed of from 5000 to 8000 rpm for airspeeds of from 130 to 175 miles per hour. The requirement that the impeller maintain rotational speeds of - between 5000 and 8000 rpm as the impeller output varied from 0 to ll.7 kilowatts at airspeeds of from 130 to 175 miles per hour was not met at any tims during the variable pitch tests. The main difficulty seemed to be the inability of the impeller blades to change blade-pitch angle smoothly and quickly as load conditions varied. There was some indication that the vibration normally occurring on an airplane might cause the impeller to operate satisfactorily.
Low speed wind tunnel tests of space shuttle lateral and longitudinal static stability characteristics at Mach 0.25
Explore the source record for details and available documents.
Two 0.00325-scale models of a space shuttle orbiter were tested in trisonic wind tunnel to obtain force, static stability, and control effectiveness data by six component internal strain gauge balance. Two separate configurations were tested; however, the fuselage and basic wing were of one-piece construction. The configurations were varied by replacing the straight wing tip extensions with upswept wing tips. Directional stability was provided for one configuration by a centerline vertical tail. Due to the one-piece body/wing construction, no body-alone data were obtained. The effect of tip fins and vertical tail size were, however, investigated. Both configurations were tested over a Mach range of 0.6 to 4.96 with data taken at angles of attack from minus 4 deg to 60 deg and at angles of sideslip from minus 4 deg to 10 deg.
Explore the source record for details and available documents.
Icing alters the shape and surface characteristics of aircraft components, which results in altered aerodynamic forces and moments caused by air flow over those iced components. The typical effects of icing are increased drag, reduced stall angle of attack, and reduced maximum lift. In addition to the performance changes, icing can also affect control surface effectiveness, hinge moments, and damping. These effects result in altered aircraft stability and control and flying qualities. Over the past 80 years, methods have been developed to understand how icing affects performance, stability and control. Emphasis has been on wind tunnel testing of two-dimensional subscale airfoils with various ice shapes to understand their effect on the flow field and ultimately the aerodynamics. This research has led to wind tunnel testing of subscale complete aircraft models to identify the integrated effects of icing on the aircraft system in terms of performance, stability, and control. Data sets of this nature enable pilot in the loop simulations to be performed for pilot training, or engineering evaluation of system failure impacts or control system design.