Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING BODY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Analysis of transonic flow about lifting wing-body configurations

An analytical solution was obtained for the perturbation velocity potential for transonic flow about lifting wing-body configurations with order-one span-length ratios and small reduced-span-length ratios and equivalent-thickness-length ratios. The analysis is performed with the method of matched asymptotic expansions. The angles of attack which are considered are small but are large enough to insure that the effects of lift in the region far from the configuration are either dominant or comparable with the effects of thickness. The modification to the equivalence rule which accounts for these lift effects is determined. An analysis of transonic flow about lifting wings with large aspect ratios is also presented.

Barnwell, R. W.↗
NASA NTRS1992

Effect of canard deflection on close-coupled canard-wing-body aerodynamics

The thin-layer Navier-Stokes equations are solved for the flow about a canard-wing-body configuration at transonic Mach numbers of 0.85 and 0.90, angles of attack from -4 to 10 degrees and canard deflection angles from -10 to +10 degrees. Effects of canard deflection on aerodynamic performance, including canard-wing vortex interaction, are investigated. Comparisons with experimental measurements of surface pressures, lift, drag and pitching moments are made to verify the accuracy of the computations. The results of the study show that the deflected canard downwash not only influences the formation of the wing leading-edge vortex, but can cause the formation of an unfavorable vortex on the wing lower surface as well.

Tu, Eugene L.↗
NASA NTRS2012

Sensitivity of Mission Energy Consumption to Turboelectric Distributed Propulsion Design Assumptions on the N3-X Hybrid Wing Body Aircraft

In a previous study by the authors it was shown that the N3-X, a 300 passenger hybrid wing body (HWB) aircraft with a turboelectric distributed propulsion (TeDP) system, was able to meet the NASA Subsonic Fixed Wing (SFW) project goal for N+3 generation aircraft of at least a 60% reduction in total energy consumption as compared to the best in class current generation aircraft. This previous study combined technology assumptions that represented the highest anticipated values that could be matured to technology readiness level (TRL) 4-6 by 2030. This paper presents the results of a sensitivity analysis of the total mission energy consumption to reductions in each key technology assumption. Of the parameters examined, the mission total energy consumption was most sensitive to changes to total pressure loss in the propulsor inlet. The baseline inlet internal pressure loss is assumed to be an optimistic 0.5%. An inlet pressure loss of 3% increases the total energy consumption 9%. However changes to reduce inlet pressure loss can result in additional distortion to the fan which can reduce fan efficiency or vice versa. It is very important that the inlet and fan be analyzed and optimized as a single unit. The turboshaft hot section is assumed to be made of ceramic matrix composite (CMC) with a 3000 F maximum material temperature. Reducing the maximum material temperature to 2700 F increases the mission energy consumption by only 1.5%. Thus achieving a 3000 F temperature in CMCs is important but not central to achieving the energy consumption objective of the N3-X/TeDP. A key parameter in the efficiency of superconducting motors and generators is the size of the superconducting filaments in the stator. The size of the superconducting filaments in the baseline model is assumed to be 10 microns. A 40 micron filament, which represents current technology, results in a 200% increase in AC losses in the motor and generator stators. This analysis shows that for a system with 40 micron filaments the higher stator losses plus the added weight and power of larger cryocoolers results in a 4% increase in mission energy consumption. If liquid hydrogen is used to cool the superconductors the 40 micron fibers results in a 200% increase in hydrogen required for cooling. Each pound of hydrogen used as fuel displaces 3 pounds of jet fuel. For the N3-X on the reference mission the additional hydrogen due to the increase stator losses reduces the total fuel weight 10%. The lighter fuel load and attendant vehicle resizing reduces the total energy consumption more than the higher stator losses increase it. As a result with hydrogen cooling there is a slight reduction in mission energy consumption with increasing stator losses. This counter intuitive result highlights the need to consider the full system impact of changes rather than just at the component or subsystem level.

Felder, James L.↗
NASA NTRS1958

Experimental Wind-Tunnel Investigation of the Transonic Damping-in-Pitch Characteristics of Two Wing-Body Combinations

The results of an experimental wind-tunnel investigation of the damping in pitch of two wing-body combinations are presented. The tests were conducted in the Ames 14-foot transonic wind tunnel over a Mach number range from 0.60 to 1.18. Reynolds numbers varied from 2.3 million to 5.5 million. One model with a triangular wing of aspect ratio 2 having NACA 0003-63 sections was oscillated at an amplitude of 1.5 and a frequency of 17 cycles per second. The second model with a straight, tapered wing of aspect ratio 3 having 3-percent biconvex circular-arc sections was oscillated at an amplitude of 1.0 deg and a frequency of 21 cycles per second. The tests were made with the models at a mean angle of attack of 0 deg. The models were oscillated with a dynamic balance that was actuated by an electrohydraulic servo valve. The results of this investigation indicate the usefulness of this new apparatus. The experimental results of a previous damping-in-pitch investigation conducted in the Ames 6- by 6-foot supersonic wind tunnel at Mach numbers from 1.2 to 1.7 are included along with the theoretical results for this Mach number range. In the region of Mach numbers available for comparison, good agreement is shown to exist between the data obtained in the two facilities, except for some inconsistency in the slopes of the curves at M = 1.2 for the triangular wing. The results of this investigation clearly show that for the models tested the maximum values of the damping in pitch occur at Mach numbers very close to 1.0, and that abrupt changes in the pitch damping are encountered near sonic velocity.

Emerson, Horace F.↗
NASA NTRS1991

Unsteady Navier-Stokes computations on a wing-body configuration in ramp motions

Unsteady Navier-Stokes computations are conducted for transonic flows over a wing-body configuration undergoing prescribed ramp motions. The ramp motion from 0 to 15 deg includes angles of attack where vortex breakdown is observed experimentally. The vortex breakdown is found to be delayed until after the ramp motion ends. The dynamic effects on the loads are also demonstrated. The moment coefficient is found to be sensitive to the effect of the virtual mass of the fluid. To verify the numerical results, a grid refinement study has been performed for both steady and unsteady flow conditions, by using up to approximately one million grid points. The results show that the coarse grid can give integrated quantities reasonably well, whereas the finer grids give a more detailed flow structure. Comparisons are also made with available steady-state experimental data.

Obayashi, Shigeru↗
NASA NTRS2011

X-48B Blended Wing Body Ground to Flight Correlation Update

The program objectives are: (1) Assess stability & control characteristics of a Blended Wing Body (BWB) class vehicle in free-flight conditions, (2) Assess flight control algorithms designed to provide desired flight characteristics, and (3) Evaluate prediction and test methods for BWB class vehicles.

Vicroy, Dan↗
NASA NTRS2014

Hybrid-Wing-Body Vehicle Composite Fuselage Analysis and Case Study

Recent progress in the structural analysis of a Hybrid Wing-Body (HWB) fuselage concept is presented with the objective of structural weight reduction under a set of critical design loads. This pressurized efficient HWB fuselage design is presently being investigated by the NASA Environmentally Responsible Aviation (ERA) project in collaboration with the Boeing Company, Huntington Beach. The Pultruded Rod-Stiffened Efficient Unitized Structure (PRSEUS) composite concept, developed at the Boeing Company, is approximately modeled for an analytical study and finite element analysis. Stiffened plate linear theories are employed for a parametric case study. Maximum deflection and stress levels are obtained with appropriate assumptions for a set of feasible stiffened panel configurations. An analytical parametric case study is presented to examine the effects of discrete stiffener spacing and skin thickness on structural weight, deflection and stress. A finite-element model (FEM) of an integrated fuselage section with bulkhead is developed for an independent assessment. Stress analysis and scenario based case studies are conducted for design improvement. The FEM model specific weight of the improved fuselage concept is computed and compared to previous studies, in order to assess the relative weight/strength advantages of this advanced composite airframe technology

Mukhopadhyay, Vivek↗
NASA NTRS1980

A study of wing body blending for an advanced supersonic transport

Increases in supersonic cruise lift drag ratio were sought at Mach numbers 2.2 and 2.7 using wing body planform and thickness blending. Constrained twist and camber optimization was performed in the presence of nacelles. Wing and fuselage thickness distributions were optimized for either minimum volume wave drag or minimum total pressure wave drag. The zero leading edge suction lift drag ratios were determined for three wing planforms. The magnitude of the effect of leading edge suction on attainable lift drag ratio was defined on one planform and estimation of available leading edge suction was made.

Goebel, T. P.↗
NASA NTRS1976

Effects of wing leading-edge radius and Reynolds number on longitudinal aerodynamic characteristics of highly swept wing-body configurations at subsonic speeds

An investigation was conducted in the Langley low turbulence pressure tunnel to determine the effects of wing leading edge radius and Reynolds number on the longitudinal aerodynamic characteristics of a series of highly swept wing-body configurations. The tests were conducted at Mach numbers below 0.30, angles of attack up to 16 deg, and Reynolds numbers per meter from 6.57 million to 43.27 million. The wings under study in this investigation had leading edge sweep angles of 61.7 deg, 64.61 deg, and 67.01 deg in combination with trailing edge sweep angles of 0 deg and 40.6 deg. The leading edge radii of each wing planform could be varied from sharp to nearly round.

Henderson, W. P.↗
NASA NTRS1987

Subsonic wind-tunnel measurements of a slender wing-body configuration employing a vortex flap

A wind tunnel study at Mach 0.4 was conducted for a slender wing-body configuration with a leading edge vortex flap of curved planform that is deflectable about a 74 degree swept hinge line. The basic data consist of a unique combination of longitudinal aerodynamic, surface pressure, and vortex flap hinge-moment measurements on a common model. The longitudinal aerodynamic, pressure and hinge-moment data are presented without analysis in tabular format. Plots of the tabulated pressure data are also given.

Frink, Neal T.↗
NASA NTRS2003

Blended Wing Body Systems Studies: Boundary Layer Ingestion Inlets With Active Flow Control

A CFD analysis was performed on a Blended Wing Body (BWB) aircraft with advanced, turbofan engines analyzing various inlet configurations atop the aft end of the aircraft. The results are presented showing that the optimal design for best aircraft fuel efficiency would be a configuration with a partially buried engine, short offset diffuser using active flow control, and a D-shaped inlet duct that partially ingests the boundary layer air in flight. The CFD models showed that if active flow control technology can be satisfactorily developed, it might be able to control the inlet flow distortion to the engine fan face and reduce the powerplant performance losses to an acceptable level. The weight and surface area drag benefits of a partially submerged engine shows that it might offset the penalties of ingesting the low energy boundary layer air. The combined airplane performance of such a design might deliver approximately 5.5% better aircraft fuel efficiency over a conventionally designed, pod-mounted engine.

Geiselhart, Karl A.↗
NASA NTRS1959

Stability and Control Characteristics at Subsonic Speeds of a Flat-Top Arrowhead Wing-Body Combination

A wind-tunnel investigation was made to determine the longitudinal- and lateral-stability derivatives of a flat-top wing-body configuration at Mach numbers from 0.22 to 0.90 and Reynolds numbers of 3.5 and 17 million. The wing had a leading-edge sweepback of 78.9 deg and a cathedral of 45 deg on the outer panels. The tests included the determination of the effectiveness of elevon and rudder controls and also an investigation of ground effects. The model was tested at angles of attack up to 28 deg and angles of sideslip up to 18 deg. The dynamic response of this configuration has been determined from the wind-tunnel data for a simulated airplane having a wing loading of 17.7 pounds per square foot. The longitudinal data show a forward shift in aerodynamic center of 10 percent of the mean aerodynamic chord as the lift coefficient is increased above 0.1. Although flown in the lift range of decreasing stability, the simulated airplane did not encounter pitch-up in maneuvers initiated from steady level flight with zero static margin unless a load factor of 2.2 was exceeded. This maneuver margin was provided by a large value of pitching moment due to pitching velocity. The number of cycles to damp the Dutch roll mode to half amplitude, the time constants of the roll subsidence and spiral divergence modes, and control effectiveness in roll are computed. The lateral stability is shown to be positive but is marginal in meeting the military specifications for today's aircraft. An analog computer study has been made in five degrees of freedom (constant velocity) which illustrates that the handling characteristics are satisfactory. Several programed rolling maneuvers and coordinated turns also illustrate the handling qualities of the airplane.

Buell, Donald A.↗
NASA NTRS2010

Wake Measurement Downstream of a Hybrid Wing Body Model with Blown Flaps

Flow-field measurements were obtained in the wake of a full-span Hybrid Wing Body model with internally blown flaps. The test was performed at the NASA Langley 14 x 22 Foot Subsonic Tunnel at low speeds. Off-body measurements were obtained with a 7-hole probe rake survey system. Three model configurations were investigated. At 0deg angle of attack the surveys were completed with 0deg and 60deg flap deflections. At 10deg angle of attack the wake surveys were completed with a slat and a 60deg flap deflection. The 7-hole probe results further quantified two known swirling regions (downstream of the outboard flap edge and the inboard/outboard flap juncture) for the 60deg flap cases with blowing. Flowfield results and the general trends are very similar for the two blowing cases at nozzle pressure ratios of 1.37 and 1.56. High downwash velocities correlated with the enhanced lift for the 60deg flap cases with blowing. Jet-induced effects are the largest at the most inboard station for all (three) velocity components due in part to the larger inboard slot height. The experimental data are being used to improve computational tools for high-lift wings with integrated powered-lift technologies.

Lin, John C.↗
NASA NTRS2001

Computational Fluid Dynamics (CFD) Design of a Blended Wing Body (BWB) with Boundary Layer Ingestion (BLI) Nacelles

A study is being conducted to improve the propulsion/airframe integration for the Blended Wing-Body (BWB) configuration with boundary layer ingestion nacelles. TWO unstructured grid flow solvers, USM3D and FUN3D, have been coupled with different design methods and are being used to redesign the aft wing region and the nacelles to reduce drag and flow separation. An initial study comparing analyses from these two flow solvers against data from a wind tunnel test as well as predictions from the OVERFLOW structured grid code for a BWB without nacelles has been completed. Results indicate that the unstructured grid codes are sufficiently accurate for use in design. Results from the BWB design study will be presented.

Morehouse, Melissa B.↗
NASA NTRS1999

Rib for blended wing-body aircraft

Structural ribs for providing structural support for a structure, such as the pressure cabin of a blended-wing body aircraft. In a first embodiment, the ribs are generally Y-shaped, being comprised of a vertical web and a pair of inclined webs attached to the vertical web to extend upwardly and outwardly from the vertical web in different directions, with only the upper edges of the inclined webs being attached to a structural element. In a second embodiment, the ribs are generally trident-shaped, whereby the vertical web extends upwardly beyond the intersection of the inclined webs with the vertical web, with the upper edge of the vertical web as well as the upper edges of the inclined webs being attached to the same structural element.

Hawley, Arthur V.↗
NASA NTRS2016

NASA Environmentally Responsible Aviation Hybrid Wing Body Flow-Through Nacelle Wind Tunnel CFD

Wind tunnel tests of a 5.75% scale model of the Boeing Hybrid Wing Body (HWB) configuration were conducted in the NASA Langley Research Center (LaRC) 14'x22' and NASA Ames Research Center (ARC) 40'x80' low speed wind tunnels as part of the NASA Environmentally Responsible Aviation (ERA) Project. Computational fluid dynamics (CFD) simulations of the flow-through nacelle (FTN) configuration of this model were performed before and after the testing. This paper presents a summary of the experimental and CFD results for the model in the cruise and landing configurations.

Environmentally Responsible Aviation↗