Search NASA⌕ Search

SEARCH · Search NASA

Results for “Waste Form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Investigating the Durability of Iodine Waste Forms in Dilute Conditions

To prevent the release of radioiodine during the reprocessing of used nuclear fuel or in the management of other wastes, many technologies have been developed for iodine capture. The capture is only part of the challenge as a durable waste form is required to ensure safe disposal of the radioiodine. This work presents the first durability studies in dilute conditions of two AgI-containing waste forms: hot-isostatically pressed silver mordenite (AgZ) and spark plasma sintered silver-functionalized silica aerogel (SFA) iodine waste forms (IWF). Using the single-pass flow-through (SPFT) test method, the dissolution rates respective to Si, Al, Ag and I were measured for variants of the IWFs. By combining solution and solid analysis information on the corrosion mechanism neutral-to-alkaline conditions was elucidated. The AgZ samples were observed to have corrosion preferentially occur at secondary phases with higher Al and alkali content. These phases contained a lower proportion of I compared with the matrix. The SFA samples experienced a higher extent of corrosion at Si-rich particles, but an increased addition of Si to the waste led to an improvement in corrosion resistance. The dissolution rates for the IWF types are of similar magnitude to other Si-based waste form materials measured using SPFT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a Performance and Processing Property Acceptance Region for Cementitious Low-Level Waste Forms at Savannah River Site - 13174

The Saltstone Production and Disposal Facilities (SPF and SDF) at the Savannah River Site (SRS) have been treating decontaminated salt solution, a low-level aqueous waste stream (LLW) since facility commissioning in 1990. In 2012, the Saltstone Facilities implemented a new Performance Assessment (PA) that incorporates an alternate design for the disposal facility to ensure that the performance objectives of DOE Order 435.1 and the National Defense Authorization Act (NDAA) of Fiscal Year 2005 Section 3116 are met. The PA performs long term modeling of the waste form, disposal facility, and disposal site hydrogeology to determine the transport history of radionuclides disposed in the LLW. Saltstone has been successfully used to dispose of LLW in a grout waste form for 15 years. Numerous waste form property assumptions directly impact the fate and transport modeling performed in the PA. The extent of process variability and consequence on performance properties are critical to meeting the assumptions of the PA. The SPF has ensured performance property acceptability by way of implementing control strategies that ensure the process operates within the analyzed limits of variability, but efforts continue to improve the understanding of facility performance in relation to the PA analysis. A similar understanding of the impact of variability on processing parameters is important from the standpoint of the operability of the production facility. The fresh grout slurry properties (particularly slurry rheology and the rate of hydration and structure formation) of the waste form directly impact the pressure and flow rates that can be reliably processed. It is thus equally important to quantify the impact of variability on processing parameters to ensure that the design basis assumptions for the production facility are maintained. Savannah River Remediation (SRR) has been pursuing a process that will ultimately establish a property acceptance region (PAR) to incorporate elements important to both processability and long-term performance properties. This process involves characterization of both emplaced product samples from the disposal facility and laboratory-simulated samples to demonstrate the effectiveness of the lab simulation. With that basis confirmed, a comprehensive variability study using non-radioactive simulants will define the acceptable PAR, or 'operating window' for Saltstone production and disposal. This same process will be used in the future to evaluate new waste streams for disposal or changes to the existing process flowsheet. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Krypton-85 Legacy Waste Forms: Part II

During a removal of legacy materials from one hot cell at the Idaho National Laboratory in 2010, five metal capsules and some loose zeolite material were identified as krypton (Kr) immobilization test specimens produced in the late 1970s under the Airborne Waste Management Program (AWMP). This AWMP research and development effort examined the encapsulation of 85Kr within a collapsed zeolite structure for use as a potential waste form for long-term storage. The recovered capsules appeared to have been placed to the side and remained untouched after the AWMP was halted in the mid-1980s. These reclaimed capsules and loose material presented a unique opportunity to study a potential 85 Kr waste form after three half-lives had elapsed. The first phase of this study included two parts: The first was to assess the physical condition of the capsule walls, and the second was to examine the Kr-containing material within the capsules. The first part of this study was previously reported and noted that substantial corrosion was observed throughout each capsule wall of the two previously breached capsules that were examined. One of these capsules had been hot isostatic pressed (HIPed) and one was not HIPed. The second part of the study examined the materials contained in the two previously breached capsules. There appears to be a relatively uniform distribution of Kr and rubidium throughout the pellets examined. The chemical composition of the pellets appears to be consistent with 5A molecular sieves. The material contained within the HIPed capsules showed ~1 at. % lead (Pb). The origin of the Pb is currently indeterminate. X-ray diffraction analysis shows a significant shift from the 5A structure, most likely due to the Kr encapsulation/sintering process that occurred when the samples were made. Calculations based on the energy dispersive spectrometry elemental analysis show a residual Kr level within the pellets that is within a factor of 2 of the reported Kr capacities for this type of processed material. This provides a clear indication that a significant fraction of the Kr initially encapsulated in the material remained within the waste form even following a significant breach of the capsule wall. As a result, it would appear that this Kr immobilization method, even in non-HIPed form, is very promising as a waste form for long-term storage. The successful analysis of these two breached capsules forms a solid basis for the future analysis of the remaining unbreached capsules, which offers the opportunity to provide an even more complete understanding of the long-term Kr retention performance of this promising waste form.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hot Isostatically Pressed Ceramic Waste forms for High Dose Spent Adsorbents - 18129

Decommissioning and clean-up of nuclear facilities requires the development of new technologies to condition radioactive wastes, producing passively safe waste packages of minimal volume, to reduce storage and disposal costs. We have applied hot isostatic pressing to demonstrate conceptual waste forms for high dose spent adsorbents (i.e. ion exchange materials) present on the Sellafield site, UK, and Fukushima Daiichi site, Japan. These radioactive wastes pose several challenges which demand early conditioning to produce a passively safe wasteform, including: a wet and granular nature, and hence dispersible as a result of loss of containment; a very high dose rates as a result of their selectivity for short lived radionuclides (e.g. Sr-90, Cs-137, Co-60); radiogenic self-heating, as a result of the concentration of such lived radio nuclides; hydrogen production as a result of radiolysis of entrained water [1]. Here, we demonstrate the conversion of natural inorganic ion exchange materials into multiphase ceramic waste forms, achieving a waste loading of 100 wt.% and density in excess of 97% theoretical. High resolution thermogravimetric analysis coupled with mass spectroscopy was utilised to characterise the evolution of water and volatiles during the in-can bake out step, prior to the HIP cycle. This allowed optimisation of the bake out parameters (temperature, time and vacuum) to enable complete removal of water and volatiles, affording ceramic bodies with minimal residual porosity by hot isostatic pressing at 1250 deg. C for 4 h in stainless steel canisters. Characterisation of the ceramic waste forms by SEM /EDX and X-ray diffraction revealed the nuclides of concern to be incorporated within well-known natural mineral and synthetic phases, with Cs partitioning into the K-feldspar. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Zircaloy Cladding as Starting Precursor for Ceramic Waste-Forms - 15562

Zircaloy cladding of spent fuel is regular waste-stream related to the process of reprocessing. It remains in the apparatus after spent fuel dissolution. The most common technique of zircaloy cladding treatment is cementation and disposal in metallic containers. In view of the high cost of the cladding material (mainly zirconium), there have been a number of proposals for this material to be recovered and re-used. However, the residual contamination of the claddings following the dissolution of the fuel and the chemical stability of the zirconium militate against any proposal for a recycling process that might be economically reasonable. At the same time there is a lot of information available about synthesis of mineral-like materials based on zirconium for immobilization of long-lived radionuclides. The object of this work was to study experimentally electrochemical dissolution of fuel rod cladding for further obtaining starting precursor for the synthesis of ceramic-waste forms. The results of experiments on electrochemical dissolution of zirconium and zirconium alloy (fuel rod cladding) in nitric acid solutions are presented. The peak dissolution rate of specimens is shown to be observed in dilute nitric acid at elevated temperatures. The rate of dissolution rises with temperature, reaching ∼40-70 mg/cm{sup 2}.h at 90 deg. C. The current yield at this point is 0.6-0.7 g/A.h. The results of analysis of the surface oxide film on specimens and residues formed during dissolution are also presented. An electrochemical dissolution of zircaloy claddings is the common technique for preparation of zirconium solutions to be used for ceramic waste form synthesis. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Alternative Electrochemical Salt Waste Forms, Summary of FY/CY2011 Results

This report summarizes the 2011 fiscal+calendar year efforts for developing waste forms for a spent salt generated in reprocessing nuclear fuel with an electrochemical separations process. The two waste forms are tellurite (TeO 2 -based) glasses and sol-gel-derived high-halide mineral analogs to stable minerals found in nature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Epsilon Metal Waste Form for Immobilization of Noble Metals from Used Nuclear Fuel

Epsilon metal (ε-metal), an alloy of Mo, Pd, Rh, Ru, and Tc, is being developed as a waste form to treat and immobilize the undissolved solids and dissolved noble metals from aqueous reprocessing of commercial used nuclear fuel. Epsilon metal is an attractive waste form for several reasons: increased durability relative to borosilicate glass, it can be fabricated without additives (100% waste loading), and in addition it also benefits borosilicate glass waste loading by eliminating noble metals from the glass and thus the processing problems related there insolubility in glass. This work focused on the processing aspects of the epsilon metal waste form development. Epsilon metal is comprised of refractory metals resulting in high reaction temperatures to form the alloy, expected to be 1500 - 2000°C making it a non-trivial phase to fabricate by traditional methods. Three commercially available advanced technologies were identified: spark-plasma sintering, microwave sintering, and hot isostatic pressing, and investigated as potential methods to fabricate this waste form. Results of these investigations are reported and compared in terms of bulk density, phase assemblage (X-ray diffraction and elemental analysis), and microstructure (scanning electron microscopy).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Secondary Waste Cementitious Waste Form Data Package for the Integrated Disposal Facility Performance Assessment

A review of the most up-to-date and relevant data currently available was conducted to develop a set of recommended values for use in the Integrated Disposal Facility (IDF) performance assessment (PA) to model contaminant release from a cementitious waste form for aqueous wastes treated at the Hanford Effluent Treatment Facility (ETF). This data package relies primarily upon recent data collected on Cast Stone formulations fabricated with simulants of low-activity waste (LAW) and liquid secondary wastes expected to be produced at Hanford. These data were supplemented, when necessary, with data developed for saltstone (a similar grout waste form used at the Savannah River Site). Work is currently underway to collect data on cementitious waste forms that are similar to Cast Stone and saltstone but are tailored to the characteristics of ETF-treated liquid secondary wastes. Recommended values for key parameters to conduct PA modeling of contaminant release from ETF-treated liquid waste are provided.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ni and Cr addition to alloy waste forms to reduce radionuclide environmental releases

Reference alloy waste forms (RAW) were fabricated and underwent hybrid corrosion/immersion testing to parameterize the ANL analytical oxidative-dissolution model to enable the calculation of fractional release rates and to determine the effectiveness of Ni and Cr trim additions in reducing release rates of radionuclide surrogates. Figure 1 shows the prototypical multiphase microstructure of the alloys with each phase type contributing about equally to the exposed surface area. The waste forms tested at SRNL were variations of the RAW-6 formulation that uses HT9 as the main alloy component, and are meant to enable evaluation of the impact of Ni and Cr trim additions on the release rates of actinides and Tc-99. The test solutions were deaerated alkaline and acidic brines, ranging in pH 3 to pH 10, representing potential repositories with those conditions. The testing approach consisted of 4 major steps; 1) bare surface corrosion measurements at pH values of 3, 5, 8, and 10, 2) hybrid potentiostatic hold/exposure measurements at pH 3, 3) measurement of radionuclide concentrations and relations to anodic current from potentiostatic holds, and 4) identification of corroding phases using SEM/EDS of electrodes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Thermodynamics of Crystallization and Phase-Separation in Melt-Derived Nuclear Waste Forms

This project aimed to gain detailed and fundamental understanding of the stability of glass waste forms to be used for safe and reliable encapsulation of nuclear waste. The focus was to understand thermodynamic and structural properties involved in crystallization and phase separation in melt-derived waste form glasses and glass-ceramics by studying a baseline glass composition with varying additives. This was achieved by combining neutron total scattering, advanced calorimetric measurements, and extensive modeling study. This project harnessed diverse and complementary approaches and expertise from four collaborating interdisciplinary institutions (two universities, one national laboratory, and one UK university partner). Samples were prepared at the national laboratory and exchanged with the two university institutions. The thermodynamic data obtained by various advanced calorimetry techniques were linked to the underlying short-range structure of waste forms measured by state-of-the-art neutron total scattering experiments. An important element of this project was extensive modeling to interpret and fundamentally understand the experimental results.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Formation and Modeling of Colloids from the Corrosion of Nuclear Waste Forms

This paper describes a model for determining the stability and associated radionuclide concentrations of colloids that might be present in the nuclear waste package environment from degradation of the nuclear waste forms. The model simplifies radionuclide–colloid behavior by assuming that all colloids can be defined as either smectite clay, a mixed actinide-bearing rare earth-zirconium oxide, iron oxyhydroxide (ferrihydrite {FeOOH}, or uranophane {Ca(UO2)2(SiO3OH)2(H2O)5}. However, for the purposes of predictive stability modeling, the colloids are conceptually represented as montmorillonite, ZrO2, hematite, and meta autunite, respectively. The model uses theoretical calculations and laboratory data to determine the stability of modeled colloids with ionic strength and pH. The true nature of colloid composition and heterogeneity, generation, and flocculation will be extremely complex, involving the formation of numerous types of phases, often depending on the composition of the various waste forms and waste package materials. This model strives to capture the uncertainty of the real system using theoretical models. In this paper, one of the four representative colloids designed to capture the behavior of the spent fuel derived colloids is described in detail.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion mechanisms for metal alloy waste forms: experiment and theory Level 4 Milestone M4FT-14LA0804024 Fuel Cycle Research & Development

This document meets Level 4 Milestone: Corrosion mechanisms for metal alloy waste forms - experiment and theory. A multiphysics model is introduces that will provide the framework for the quantitative prediction of corrosion rates of metallic waste forms incorporating the fission product Tc. The model requires a knowledge of the properties of not only the metallic waste form, but also the passive oxide films that will be generated on the waste form, and the chemistry of the metal/oxide and oxide/environment interfaces. in collaboration with experimental work, the focus of this work is on obtaining these properties from fundamental atomistic models. herein we describe the overall multiphysics model, which is based on MacDonald's point-defect model for passivity. We then present the results of detailed electronic-structure calculations for the determination of the compatibility and properties of Tc when incorporated into intermetallic oxide phases. This work is relevant to the formation of multi-component oxides on metal surfaces that will incorporate Tc, and provide a kinetic barrier to corrosion (i.e. the release of Tc to the environment). Atomistic models that build upon the electronic structure calculations are then described using the modified embedded atom method to simulate metallic dissolution, and Buckingham potentials to perform classical molecular dynamics and statics simulations of the technetium (and, later, iron-technetium) oxide phases. Electrochemical methods were then applied to provide some benchmark information of the corrosion and electrochemical properties of Technetium metal. The results indicate that published information on Tc passivity is not complete and that further investigation is warranted.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Physical properties of an alumino-silicate waste form for cesium and strontium.

Nuclear fuel reprocessing will be required to sustain nuclear power as a baseload energy supplier for the world. New reprocessing schemes offer an opportunity to develop a better strategy for recycling elements in the fuel and preparing stable waste forms. Advanced strategies could create a waste stream of cesium, strontium, rubidium, and barium. Some physical properties of a waste form containing these elements sintered into bentonite clay were evaluated. We prepared samples loaded to 27% by mass to a density of approximately 3 g/cm{sup 3}. Sintering temperatures of up to 1000 C did not result in volatility of cesium. Instead, the crystallinity noticeably increased in the waste form as temperatures increased from 600 to 1000 C. Assemblages of silicates were formed. Significant water evolved at approximately 600 C but no other gases were generated at higher temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion Tests with Developmental Iron Phosphate Glass Waste Forms

Corrosion tests are in progress to assess the dissolution behavior of developmental iron phosphate waste forms for salt waste from electrochemical separation operations. Specimens cut from materials made at PNNL to represent a range of waste salt loadings in prototype composition DPF-5 and a range of iron oxide loadings in prototype composition DPF-3 were subjected to modified ASTM C1308 tests to assess the compositional effects on the relative durabilities and retention of immobilized salt cations. The materials were composed of different amounts of glass and crystalline phases. The test results show both the intrinsic durability of the material and the salt cation retention decrease as the total amount of salt cations added to the material is increased. The results of ASTM C1220 and ASTM C1285 tests conducted with materials DPF5-280 and DPF5-336, which contained about 28% and 34% salt cations (on a mass oxide basis) and bounded the durabilities of the other materials, show that solution feedback does not attenuate the dissolution rate. This suggests the degradation of iron phosphate waste forms can be modelled by using a constant rate that probably depends on the composition and volume fraction of the glass phase. A reference composition should be formulated and used in tests to determine those dependencies. The ASTM C1220 and ASTM C1285 tests with DPF5-280 and DPF5-336 remain in progress to corrode the specimens enough to distinguish the relative extents of glass and crystalline phase corrosion by microscopic examinations. Those results are expected to provide insights regarding the relative dissolution rates of crystalline and glass phases and impact on durability to inform the formulation of the reference composition.

Ebert, W. L.↗

SCALE UP OF CERAMIC WASTE FORMS FOR THE EBR-II SPENT FUEL TREATMENT PROCESS

ABSTRACT SCALE UP OF CERAMIC WASTE FORMS FOR THE EBR-II SPENT FUEL TREATMENT PROCESS Matthew C. Morrison, Kenneth J. Bateman, Michael F. Simpson Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415 The ceramic waste process is the intended method for disposing of waste salt electrolyte, which contains fission products from the fuel-processing electrorefiners (ER) at the INL. When mixed and processed with other materials, the waste salt can be stored in a durable ceramic waste form (CWF). The development of the CWF has recently progressed from small-scale testing and characterization to full-scale implementation and experimentation using surrogate materials in lieu of the ER electrolyte. Two full-scale (378 kg and 383 kg) CWF test runs have been successfully completed with final densities of 2.2 g/cm3 and 2.1 g/cm3, respectively. The purpose of the first CWF was to establish material preparation parameters. The emphasis of the second pre-qualification test run was to evaluate a preliminary multi-section CWF container design. Other considerations were to finalize material preparation parameters, measure the material height as it consolidates in the furnace, and identify when cracking occurs during the CWF cooldown process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of long-term performance models for radioactive waste forms

The long-term performance of solid radioactive waste is measured by the release rate of radionuclides into the environment, which depends on corrosion or weathering rates of the solid waste form. The reactions involved depend on the characteristics of the solid matrix containing the radioactive waste, the radionuclides of interest, and their interaction with surrounding geologic materials. This chapter describes thermo-hydro-mechanical and reactive transport models related to the long-term performance of solid radioactive waste forms, including metal, ceramic, glass, steam reformer and cement. Future trends involving Monte-Carlo simulations and coupled/multi-scale process modeling are also discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characteristics of metal waste forms containing technetium and uranium

2 prototype alloys: RAW-1(Tc) and RAW-2(UTc) suitable for a wide range of waste stream compositions are being evaluated to support development of a waste form degradation model that can be used to calculate radionuclide source terms for a range of waste form compositions and disposal environments. Tests and analyses to support formulation of waste forms and development of the degradation model include detailed characterizations of the constituent phases using SEM/EDS and TEM, electrochemical tests to quantify the oxidation behavior and kinetics of the individual and coupled phases under a wide range of environmental conditions, and corrosion tests to measure the gross release kinetics of radionuclides under aggressive test conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multi-phase glass-ceramics as a waste form for combined fission products: alkalis, alkaline earths, lanthanides, and transition metals

In this study, multi-phase silicate-based glass-ceramics were investigated as an alternate waste form for immobilizing non-fissionable products from used nuclear fuel. Currently, borosilicate glass is the waste form selected for immobilization of this waste stream, however, the low thermal stability and solubility of MoO{sub 3} in borosilicate glass translates into a maximum waste loading in the range of 15-20 mass%. Glass-ceramics provide the opportunity to target durable crystalline phases, e.g., powellite, oxyapatite, celsian, and pollucite, that will incorporate MoO{sub 3} as well as other waste components such as lanthanides, alkalis, and alkaline earths at levels 2X the solubility limits of a single-phase glass. In addition a glass-ceramic could provide higher thermal stability, depending upon the properties of the crystalline and amorphous phases. Glass-ceramics were successfully synthesized at waste loadings of 42, 45, and 50 mass% with the following glass additives: B{sub 2}O{sub 3}, Al{sub 2}O{sub 3}, CaO and SiO{sub 2} by slow cooling form from a glass melt. Glass-ceramics were characterized in terms of phase assemblage, morphology, and thermal stability. The targeted phases: powellite and oxyapatite were observed in all of the compositions along with a lanthanide borosilicate, and cerianite. Results of this initial investigation of glass-ceramics show promise as a potential waste form to replace single-phase borosilicate glass.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗