SEARCH · Search NASA

Results for “Wave Energy Converter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Characterizing Interference in a Wave-Powered Buoy

Oceanographic measurement buoys are power constrained by the capacity of their batteries and the available solar power. Many buoys are in locations with abundant wave energy, but wave energy converters are not being used to power them. One reason wave energy converters may not have not been developed for wave measurement buoys is that many buoys measure waves by precisely following the wave motion. Wave energy converters may inhibit this wave-following ability by altering a buoy's response to incoming waves. In this report, we present the results of field tests that measured the extent to which buoy motion was changed by modifications to the buoy for wave energy harvesting. The motion of the buoy was significantly modified by the addition of the hardware components necessary for harvesting wave energy. The ratio of the mass of the wave energy converter to the mass of the buoy was high for the system tested, which strongly affected buoy motion. A lower value for this ratio would decrease the effect of the wave energy converter on the motion of the buoy, thereby decreasing the impact on the buoy's ability to measure waves but also decreasing the power production capabilities. Therefore, the use of wave energy converters to power wave measurement buoys may be feasible for large buoys that measure low-frequency waves and have low power requirements.

16 TIDAL AND WAVE POWER↗

DOE OSTI2024

Using Fiducial Markers for Pose Estimation of an OSWEC in a Wave Tank: Preprint

In this study, we consider a novel method of sensing the motion of a wave energy converter during testing in a wave flume under the influence of incoming waves. The wave energy converter considered in our research is an oscillating surge wave energy converter, which is a hinged paddle that responds to incoming waves. Motion sensing is normally done with inertial sensors, which can hinder the motion due to suspended cables that carry power and transmit signals. Our proposed method is contactless and can be implemented economically. A camera is used to record different marker patterns affixed to the moving paddle and the motion deduced by pose estimation algorithms. Fiducial markers are commonly used for robot localization and in augmented reality. There are many types of fiducial markers, including ArUco-type markers which are accurate, fast and robust. The system consists of markers attached to the paddle element and recorded using a machine vision camera. A pose estimation algorithm is then applied to the detected markers to estimate the tilt of the paddle. In this work, we examine the challenges of image acquisition and calibration for underwater targets, compare the motion obtained by this new system with a calibrated tilt sensor and identify areas where the new system may be superior.

computer vision↗

DOE OSTI2024

Laboratory Upgrade Point Absorber WEC-Sim Model with MoorDyn Moorings

This dataset includes a WEC-Sim and MoorDyn model of the Laboratory Upgrade Point Absorber (LUPA). LUPA is an open-source wave energy converter designed and tested by Oregon State University. The files provided here constitute a stable LUPA configuration with three mooring lines. This model is 1/20 scale, optimized for the O.H. Hinsdale Wave Lab at Oregon State University. This model of LUPA adds MoorDyn functionality for more accurate mooring predictions and uses a more stable, updated version of LUPA's current physical configuration. This model is for WEC-Sim Version 6.0. A recent update of WEC-Sim has changed some functionality of MoorDyn such that this model will not work with WEC-Sim Version 6.1.

16 TIDAL AND WAVE POWER↗

DOE OSTI2022

Internal Reaction Mass Taxonomy and Narrow-Down Study

Internal reaction mass (IRM) wave energy converters (WEC) capture wave energy by reacting against a moving mass that is suspended within their hulls. Due to their hermetically sealed Power Take Off (PTO), compact form factor and relatively simple mooring requirements, the National Renewable Energy Laboratory has identified IRM WECs are good candidates for applications such as ocean observation. A literature review of existing IRM mechanisms lead to the classification of IRM WECs based on their principal method of energy capture and principal axes of operation. The IRM categories include sliding mass, pendular and gyroscopic devices. A narrow down study was conducted to ascertain the most promising mechanisms for further investigation; devices were evaluated based on a decision matrix of weighted criteria that included device power output, prototypability and power to mass ratio. The narrow down study identified the issue of achieving resonance with pendulum-based designs, as well as the poor response produced by reaction to long period waves. Chaotic pendula and methods to multiply agitation were identified as a means to increase power output. Alternative methods of power generation, such as triboelectric nanogenerators, were also identified as a technology that would benefit from multiplied agitation and chaotic motion. This work was funded under the U.S. Department of Energy's Water Power Technologies Office's Powering the Blue Economy portfolio.

ENGINEERING,TIDAL AND WAVE POWER↗

DOE OSTI2026

Analysis of Power Electronic Solutions for Wide-Range Wave Energy Input

Wave energy is a largely untapped energy source with the potential to provide 290 TWh per year to the continental United States. As a new technology, wave energy converters are less efficient and reliable compared to established energy sources, leaving the vast energy of the sea largely unutilized. Wave energy is uniquely inconsistent, with large fluctuations. Paired with harsh operating environments and difficulty in repair, the power electronics designed to harvest wave energy need to be reliable, cost-effective, and able to work in a wide operating band. The literature on existing power electronics in wave energy converters and lessons learned across other industries provide a framework of topologies to simulate. WEC-Sim, an open-source hydrodynamic platform in MATLAB Simulink developed by the National Laboratory of the Rockies, was used to simulate a wide range of power electronics under a variety of wave conditions. This paper provides a comprehensive investigation into existing wave energy power electronics converters, state-of-the-art topologies that can be applied to wave energy, and novel solutions to wave conversion.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Review of TEAMER Awards for WEC-Sim Support: Preprint

Testing Expertise and Access for Marine Energy Research (TEAMER) is a U.S. Department of Energy Water Power Technologies Office sponsored program, overseen by the Pacific Ocean Energy Trust, which aims to advance the state of marine energy technologies. The program connects technology developers with experts at U.S. facilities, including numerical modeling and analysis facilities, like WEC-Sim. The WEC-Sim facility is supported by the WEC-Sim development team at Sandia National Laboratories and the National Renewable Energy Laboratory. WEC-Sim (Wave Energy Converter SIMulator) is an open-source software for simulating wave energy converters. WEC-Sim can model the multi-body dynamics of devices comprised of bodies, joints, power take-off systems, and mooring systems. Since TEAMER's first round of support in 2020, there have been eighteen TEAMER awards focused on numerical model development in WEC-Sim. TEAMER awards for WEC-Sim support have modeled a wide range of wave energy converter archetypes, including point absorbers, attenuators, oscillating water columns, and many other novel architectures. A wide variety of studies have been conducted, leading to important insights for TEAMER partners and software improvements for WECSim. This article highlights several successful WEC-Sim TEAMER awards. The awards described herein include TEAMER recipients Ocean Motion Technologies, AquaHarmonics, iProTech, East Carolina University, Virginia Tech, Maiden Wave Energy, and the University of Massachusetts Dartmouth. The awards of these seven partners contain a wide range of investigations and cover the creation of baseline hydrodynamic models, PTO modeling, geometry optimization in both boundary element methods and WECSim, and model tuning and validation.

industry support↗

DOE OSTI2022

TEAMER: FOSWEC Mooring Modeling and Analysis, Post Access Report and Data

Floating oscillating surge wave energy converters (FOSWECs) offer several advantages over bottom-hinged oscillating surge wave energy converters, including large wave potential at deep-water sites with fewer permitting and environmental concerns outside territorial waters. As a team, Stevens Institute of Technology, Virginia Tech and Resolute Marine Energy are designing a 100 kW FOSWEC with DOE support (2020-2021) for the PacWave test site "PacWave". The proposed FOSWEC consists of a floating platform, two pivoting flaps, and an innovative power-take-off (PTO). The distance between the two flaps is around half the typical wavelength, resulting in out-of-phase motion and a reduction in motion of the frame and mooring loads. The overall goal of the project is to design, build, deploy and analyze a 1:2 scale (100-kW annual averaged electrical power output) device with reduced levelized cost of energy (LCOE) and peak-to-average power ratio, through the co-design and control of the PTO, WEC, and floating platform. This submission includes a Post Access Report and data for the project of Mooring Modeling and Analysis for Floating Oscillating Surge Wave Energy Converter that Powers Marine Aquaculture of RFTS2 (request for technical support). The data are used to generate all figures in the Post Access Report. Project was a collaboration between Virginia Tech and the National Renewable Energy Lab, with funding from TEAMER.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Next-Generation Marine Energy Software Needs Assessment

The U.S. Department of Energy (DOE) Water Power Technologies Office’s (WPTO) initial investment in marine energy software was driven by needs identified over a decade ago. WPTO-funded research was first launched because of a U.S. congressional mandate that called for the DOE to officially research marine energy technologies, which also established the DOE WPTO in 2008. A congressional mandate requested the WPTO to evaluate a variety of marine energy devices, establish baseline levelized cost of energy estimates, and provide an overall report to Congress. This congressional mandate led to the Reference Model Project (RMP), for which WPTO funded a national multi-laboratory team to develop these reference models, based on state-of-the-art designs of six marine energy converter archetypes that consisted of three current energy converters and three wave energy converters (WEC). Each device was designed to operate for a specific marine resource, thus allowing the devices to serve as reference models for future studies. The RMP congressional report cited the need for improved marine energy software to handle a variety of device designs, as well as a need to standardize performance outputs. Without validated software packages and established metrics, information presented to the WPTO by technology developers could be incorrect or inaccurate and result in misleading conclusions. The recommendation to coordinate WPTO investment in software for numerical modeling and analysis was given a high priority because it would directly fill needs at the time, and focused funding would amplify impact. By sponsoring software development, WPTO would provide industry developers, university researchers, and national laboratories software that could be used, customized, and advanced, thus supporting the overall advancement of marine energy.

16 TIDAL AND WAVE POWER↗

DOE OSTI2024

Economic dispatch of offshore renewable energy resources for islanded communities with optimal storage sizing

Coastal or isolated microgrids depend on diesel generators and could benefit from renewable energy resources, especially offshore wind and wave energy. Integrating these resources into microgrids is complicated by their high intermittency, which requires optimal economic dispatch to effectively evaluate. This study considers three coastal or islanded sites, and uses mid-fidelity models of wind and wave energy technologies, and local demand data to solve the optimal economic dispatch problem. An optimal storage sizing method is developed that finds the smallest capacity of energy storage required to meet the microgrid load during each season. The storage capacity decreases by a factor of two at most when adding wave energy converters to a system. Adding wave energy converters to a farm decreases cost by about 30%. Furthermore, the required storage size varies by two to three times from summer to winter. Compared with the state-of-the-art approaches that often overlook realistic offshore renewable energy technology in microgrid economic dispatch and optimal storage sizing, the proposed solution introduced in this study allows for better site selection, microgrid design, converter selection, and storage sizing considerations for isolated microgrids.

16 TIDAL AND WAVE POWER↗

DOE OSTI2022

Ocean Energy Sandia TEAMER WEC Simulation Results

Computational fluid simulations for wave energy converters and supporting materials from Ocean Energy's WEC Buoy TEAMER project in collaboration with Sandia National Laboratories. Each file includes images and video of simulation along with the simulation files for the case. The videos and images include air and water simulations of the buoy in 2D and 3D views. Data spreadsheets of the simulation outputs are also included in the files. The data are represented as different cases in which the wave height(Hs) and peak period(Tp) were different.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Distributed Embedded Energy Converter Technologies for Marine Renewable Energy (A Technical Report)

The domain of distributed embedded energy converter technologies (DEEC-Tec) is a nascent and underexplored paradigm for harvesting and converting marine renewable energy. The paradigm distinguishes itself through its use of many small distributed embedded energy converters (DEECs) that, ultimately, are assembled through the creation of "DEEC-Tec metamaterials" to create an overall larger marine renewable energy harvesting and converting structure. As an example, such a structure could be an ocean wave energy converter - a converter whose structure is made from various types of DEEC-Tec metamaterials that harvests ocean wave energy and converts that energy into something more useful such as electricity. To that end, DEEC-Tec can be viewed at three different technology levels: (1) individual distributed embedded energy converters, also known as DEECs; (2) DEEC-Tec metamaterials-essentially, pseudo-materials made from the interconnection of many DEECs; and (3) overall larger complete marine renewable energy harvesting-converting structures-these structures being made from DEEC-Tec metamaterials. Arising directly from the application of DEEC-Tec to harvest and convert ocean wave energy are several noteworthy benefits, some of which include: (1) the lack of load concentrations into singular components or subsystems, (2) broad-banded ocean wave energy frequency harvesting and conversion, and (3) inherent redundancy-failure of some individual DEECs does not represent a failure of an entire DEEC-Tec-based WEC. This report describes DEEC-Tec by way of descriptions of those three technology levels: individual DEECs, DEEC-Tec metamaterials, and DEEC-Tec-based WECs. Moreover, the report describes corresponding research approaches and methodologies for related concepts such as DEEC-Tec-based WEC topologies and morphologies in addition to manufacturing and fabrication techniques found suitable for the application of DEEC-Tec within the general domain of marine renewable energy-moving beyond only ocean wave energy conversion.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Advanced Laboratory and Field Arrays: Technical Report for Performance Enhancement for Marine Energy Converter (MEC) Arrays (Task 5)

Task 5 consisted of two parts, wave energy converter (WEC) arrays and current energy converter (CEC) arrays. The two parts of the project were executed independently, and this report covers only the work on WECs. In this part of the task, the team characterized the behavior of and developed control schemes for wave energy converter (WEC) arrays that improved performance (i.e., maximized aggregate power generation and reduced the levelized cost of energy) over baseline, non-coordinated control approaches. Specifically, for WEC arrays: the team developed optimal layouts of arrays that considered the effect of WEC placement within an array on coordinated array control with real-time estimation schemes. The numerical codes developed through this task were made available to users for array design. These tools utilized existing commercial software as well as software developed within the project team.

13 HYDRO ENERGY↗

DOE OSTI2020

Initial conceptual demonstration of control co-design for WEC optimization

Abstract While some engineering fields have benefited from systematic design optimization studies, wave energy converters have yet to successfully incorporate such analyses into practical engineering workflows. The current iterative approach to wave energy converter design leads to sub-optimal solutions. This short paper presents an open-source MATLAB toolbox for performing design optimization studies on wave energy converters where power take-off behavior and realistic constraints can be easily included. This tool incorporates an adaptable control co-design approach, in that a constrained optimal controller is used to simulate device dynamics and populate an arbitrary objective function of the user’s choosing. A brief explanation of the tool’s structure and underlying theory is presented. To demonstrate the capabilities of the tool, verify its functionality, and begin to explore some basic wave energy converter design relationships, three conceptual case studies are presented. In particular, the importance of considering (and constraining) the magnitudes of device motion and forces in design optimization is shown.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Wave Energy Power Take-off Validation with a Hydraulicly Actuated Rotary Dynamometer and a Bi-Directional High-Power DC Supply

There are many organizations working towards the commercialization of wave energy converter technologies and are advancing their designs through the technology readiness levels (TRLs). A critical step before the field deployment of prototype wave energy converters is the validation of the subsystems and components that are contained in the wave energy converter through laboratory testing and performance characterization. In 2021, the National Renewable Energy Laboratory (NREL) developed and demonstrated a system for testing power takeoffs (PTO) with a low-speed, high-torque dynamometer and a grid-tied high-power DC power source and sink before field deployment. The hydraulic dynamometer allows for the simulation of PTO actuation from wave motion and is capable of a wide range of wave periods and heights which are represented as various speeds and torques from the dynamometer. The high-power bidirectional power supply allows for hardware in the loop and controller in the loop testing to be conducted on WEC power electronics. This presentation was made to describe the methods used by NREL research staff to test all components and sub-systems in the PTO of a novel wave energy converter before field deployment.

dynamometer↗

DOE OSTI2023

Wave Energy Power Take-Off Validation with a Hydraulicly Actuated Rotary Dynamometer and a Bidirectional High-Power DC Supply: Preprint

dynamometer↗

DOE OSTI2026

Second-order wave excitation forces in WEC-Sim/MOST: Implementation, experimental validation, and code-to-code comparison

Accurate prediction of second-order hydrodynamic loads is essential for floating bodies, including floating offshore wind turbines, wave energy converters, and hybrid wind–wave platforms. These nonlinear effects, arising from both sum- and difference-frequency forcing, are critical for capturing key response characteristics but remain challenging to model efficiently. In this work, we extend the open-source Wave Energy Converter Simulator / MATLAB for Offshore Simulation Tool by implementing second-order wave excitation forces, supporting both the full Quadratic Transfer Function formulation and the Newman approximation. The full Quadratic Transfer Function method is used for all code-to-code comparisons and experimental validation, while the Newman approximation is provided as a computationally lighter alternative. To benchmark the new capability, we perform a code-to-code comparison with OpenFAST and OrcaFlex. We then validate the enhanced model using wave-tank measurements of a 1:96 scale DeepCwind semi-submersible, showing that second-order effects are required to reproduce platform motions. The implementation employs a computationally efficient pre-computation strategy for second-order wave excitation forces, reducing simulation cost while maintaining engineering accuracy. Overall, this work advances the tool as an open-source and versatile tool for modelling floating offshore renewable-energy systems requiring second-order hydrodynamic fidelity.

17 WIND ENERGY↗

DOE OSTI2020

Development and Validation of Passive Yaw in the Open-Source WEC-Sim Code: Preprint

A passive yaw implementation is developed, validated, and explored for the Wave Energy Converter Simulator (WEC-Sim), an open-source wave energy converter modeling tool that works within MATLAB/Simulink. The Reference Model 5 (RM5) is selected for this investigation, and a WEC-Sim model of the device is modified to allow yaw motion. A boundary element method (BEM) code was used to calculate the excitation force coefficients for a range of wave headings. An algorithm was implemented in WEC-Sim to determine the equivalent wave heading from a body’s instantaneous yaw angle and interpolate the appropriate excitation coefficients to ensure the correct time-domain excitation force. This approach is able to determine excitation force for a body undergoing large yaw displacement. For the mathematically simple case of regular wave excitation, the dynamic equation was integrated numerically and found to closely approximate the results from this implementation in WEC-Sim. A case study is presented for the same device in irregular waves. In this case, computation time is increased by 32x when this interpolation is performed at every time step. To reduce this expense, a threshold yaw displacement can be set to reduce the number of interpolations performed. A threshold of 0.01 was found to increase computation time by only 22x without significantly affecting time domain results. Similar amplitude spectra for yaw force and displacements are observed for all threshold values less than or equal to 1, for which computation time is only increased by 2.2x.

50 EE - Wind and Water Power Program - Water (EE-4↗

DOE OSTI2022

Recent Developments in the WEC-Sim Open-Source Design Tool: Preprint

WEC-Sim (Wave Energy Converter SIMulator) is an open-source code for simulating wave energy converters, which has been actively developed and applied to simulate a wide variety of device archetypes and has become a popular tool since its initial release in 2014. WEC-Sim is developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) within the MATLAB/SIMULINK environment. Figure 1 illustrates a general wave-to-wire model which begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of a single WEC (or array), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modelling the entire wave-to-wire is difficult and encompass multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM) based-frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). Within this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Table 1 lists additional WEC-Sim functionalities, which are created using prebuilt Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems.

hydrodynamics modeling↗