Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wing body configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The numerical study of 3-D flow past control surfaces

The computation of a steady 3D viscous flow past a slender delta wing-body configuration with trailing edge control surfaces is presented. For the numerical simulation, a cell centered finite volume Navier-Stokes zonal method was used and, besides the standard nonplanar zonal interfacing techniques, a new zonal capability, called a 'virtual zone', was implemented. This capability enables the end caps of the wings or flaps to be gridded and interfaced with the rest of the flowfield in a natural and straightforward manner. The computational results for 0-, 10-, and 24-deg angles-of-attack were found to agree with experimental results qualitively and quantitatively.

Chaussee, Denny S.↗
NASA NTRS2011

Low Boom Configuration Analysis with FUN3D Adjoint Simulation Framework

Off-body pressure, forces, and moments for the Gulfstream Low Boom Model are computed with a Reynolds Averaged Navier Stokes solver coupled with the Spalart-Allmaras (SA) turbulence model. This is the first application of viscous output-based adaptation to reduce estimated discretization errors in off-body pressure for a wing body configuration. The output adaptation approach is compared to an a priori grid adaptation technique designed to resolve the signature on the centerline by stretching and aligning the grid to the freestream Mach angle. The output-based approach produced good predictions of centerline and off-centerline measurements. Eddy viscosity predicted by the SA turbulence model increased significantly with grid adaptation. Computed lift as a function of drag compares well with wind tunnel measurements for positive lift, but predicted lift, drag, and pitching moment as a function of angle of attack has significant differences from the measured data. The sensitivity of longitudinal forces and moment to grid refinement is much smaller than the differences between the computed and measured data.

Park, Michael A.↗
NASA NTRS1986

Three-dimensional elliptic grid generation about fighter aircraft for zonal finite-difference computations

An elliptic grid-generation method for finite-difference computations about complex aerodynamic configurations is developed. A zonal approach is used, which involves first making a coarse global grid filling the entire physical domain and then subdividing regions of that grid to make the individual zone grids. The details of the grid-generation method are presented along with results of the present application, a wing-body configuration based on the F-16 fighter aircraft.

Sorenson, R. L.↗
NASA NTRS1988

A performance index approach to aerodynamic design with the use of analysis codes only

A method is described for designing an aerodynamic configuration for a specified performance vector, based on results from several similar, but not identical, trial configurations, each defined by a geometry parameter vector. The theory shows the method effective provided that: (1) the results for the trial configuration provide sufficient variation so that a linear combination of them approximates the specified performance; and (2) the difference between the performance vectors (including the specifed performance) are sufficiently small that the linearity assumption of sensitivity analysis applies to the differences. A computed example describes the design of a high supersonic Mach number missile wing body configuration based on results from a set of four trial configurations.

Barger, Raymond L.↗
NASA NTRS2008

Experimental Investigation of the DLR-F6 Transport Configuration in the National Transonic Facility

An experimental aerodynamic investigation of the DLR (German Aerospace Center) F6 generic transport configuration has been conducted in the NASA NTF (National Transonic Facility) for CFD validation within the framework of the AIAA Drag Prediction Workshop. Force and moment, surface pressure, model deformation, and surface flow visualization data have been obtained at Reynolds numbers of both 3 million and 5 million. Flow-through nacelles and a side-of-body fairing were also investigated on this wing-body configuration. Reynolds number effects on trailing edge separation have been assessed, and the effectiveness of the side-of-body fairing in eliminating a known region of separated flow has been determined. Data obtained at a Reynolds number of 3 million are presented together for comparison with data from a previous wind tunnel investigation in the ONERA S2MA facility. New surface flow visualization capabilities have also been successfully explored and demonstrated in the NTF for the high pressure and moderately low temperature conditions required in this investigation. Images detailing wing surface flow characteristics are presented.

Gatlin, Gregory M.↗
NASA NTRS1959

Lift-Drag Ratios for an Arrow Wing With Bodies at Mach Number 3

Force and moment characteristics, including lift-drag ratios, have been measured for bodies of circular and elliptic cross section alone and combined with a warped arrow wing. The test Mach number was 2.94, and the Reynolds number was 3.5 x 10(exp 6) (based on wing mean aerodynamic chord). The experimental results show that for equal volume the use of an elliptical body can result in a noticeably higher maximum lift-drag ratio than that obtained through use of a circular body. Methods for estimating the aerodynamic characteristics have been assessed by comparing computed with experimental results. Because of good agreement of the predictions with experiment, maximum lift-drag ratios have been computed for the arrow wing in combination with bodies of various sizes. These calculations have shown that, for an efficient wing-body combination, little loss in maximum lift-drag ratio results from considerable extension of afterbody length. For example, for a wing-body configuration having a maximum lift-drag ratio of about 7.1, a loss in maximum lift-drag ratio of less than 0.2 results from a 40-percent increase in body volume by extension of afterbody length. It also appears that with body length fixed, maximum lift-drag ratio decreases almost linearly with increase in body diameter. For a wing- body combination employing a body of circular cross section, a decrease in maximum lift-drag ratio from about 9.1 for zero body diameter to about 4.6 for a body diameter of 13.5 percent of the body length was computed.

Jorgensen, Leland H.↗
NASA NTRS1991

Overview of the Beta II Two-Stage-To-Orbit vehicle design

A study of a near-term, low risk two-stage-to-orbit (TSTO) vehicle was undertaken. The goal of the study was to assess a fully reusable TSTO vehicle with horizontal takeoff and landing capability that could deliver 10,000 pounds to a 120 nm polar orbit. The configuration analysis was based on the Beta vehicle design. A cooperative study was performed to redesign and refine the Beta concept to meet the mission requirements. The vehicle resulting from this study was named Beta II. It has an all-airbreathing first stage and a staging Mach number of 6.5. The second stage is a conventional wing-body configuration with a single SSME.

Plencner, Robert M.↗
NASA NTRS1992

Supersonic full-potential methods for missile body analysis

Accounts are presented of representative applications to missile bodies of arbitrary shape of methods based on the steady form of the full potential equation. The NCOREL and SIMP full-potential codes are compared, and their results are evaluated for the cases of an arrow wing and a wing-body configuration. Attention is given to the effect of cross-sectional and longitudinal geometries. Comparisons of surface pressure and longitudinal force and moment data for circular and elliptic bodies have shown that the full-potential methods yielded excellent results in attached-flow conditions. Results are presented for a conical star body, waveriders, the Shuttle Orbiter, and a highly swept wing-body cruising at Mach 4.

Pittman, James L.↗
NASA NTRS1988

Unsteady vortex-dominated flows around maneuvering wings over a wide range of Mach numbers

The problem of unsteady flow around maneuvering wings is solved using the unsteady Euler equations. The unsteady conservative Euler equations are derived for the flow relative motion with respect to a moving (translating and rotating) frame of reference. The resulting equations can handle the most general case for unsteady three-dimensional flow around maneuvering wings or wing-body configurations undergoing six degrees of freedom motion; three translations and three rotations. The equations are solved using two computational schemes; an explicit multistage finite-volume scheme and an implicit approximately factored finite-volume scheme. The computational applications cover two cases. The first case is for a locally conical supersonic flow of rolling oscillation of a sharp-edged delta wing at zero angle of attack. The second case is for a pitching oscillation around a mean angle of attack of a NACA 0012 airfoil in transonic flow.

Kandil, Osama A.↗
NASA NTRS1993

Unsteady Navier-Stokes simulation of the canard-wing-body ramp motion

A time-accurate thin-layer Navier-Stokes simulation of the unsteady flowfield is performed for a typical canard-wing-body configuration undergoing ramp motions. The computations are made at a transonic Mach number of 0.90 and for ramp angles from 0 to 15 degrees. Accuracy is determined by comparisons with steady-state experimental data and with spatial and time-step refinement studies. During the ramp motion, the computational results show improved dynamic lift performance and a strong canard-wing interaction for the canard-on configuration. Formation of the canard leading-edge vortex is inhibited in the early stages of the ramp motion. An analysis performed on the transient flowfield after the ramp motion ends shows that the canard vortex rapidly gains strength and vortex breakdown eventually occurs. These characteristics of the canard vortex have significant influences on wing performance.

Tu, Eugene L.↗
NASA NTRS1984

The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

Grantz, A. C.↗
NASA NTRS2016

Expanding the Natural Laminar Flow Boundary for Supersonic Transports

A computational design and analysis methodology is being developed to design a vehicle that can support significant regions of natural laminar flow (NLF) at supersonic flight conditions. The methodology is built in the CDISC design module to be used in this paper with the flow solvers Cart3D and USM3D, and the transition prediction modules BLSTA3D and LASTRAC. The NLF design technique prescribes a target pressure distribution for an existing geometry based on relationships between modal instability wave growth and pressure gradients. The modal instability wave growths (both on- and off-axes crossflow and Tollmien-Schlichting) are balanced to produce a pressure distribution that will have a theoretical maximum NLF region for a given streamwise wing station. An example application is presented showing the methodology on a generic supersonic transport wingbody configuration. The configuration has been successfully redesigned to support significant regions of NLF (approximately 40% of the wing upper surface by surface area). Computational analysis predicts NLF with transition Reynolds numbers (ReT) as high as 36 million with 72 degrees of leading-edge sweep (ΛLE), significantly expanding the current boundary of ReT - ΛLE combinations for NLF. This NLF geometry provides a total drag savings of 4.3 counts compared to the baseline wing-body configuration (approximately 5% of total drag). Off-design evaluations at near-cruise and low-speed, high-lift conditions are discussed, as well as attachment line contamination/transition concerns. This computational NLF design effort is a part of an ongoing cooperative agreement between NASA and JAXA researchers.

Lynde, Michelle N.↗
NASA NTRS1977

Configuration development study of the X-24C hypersonic research airplane

Bottom line results were made of a three-phase study to determine the feasibility of designing, building, and operating, and maintaining an air-launched high performance aircraft capable of cruising at speeds up to Mach 8 for short durations. The results show that Lockalloy heat-sink structure affords the capability for a 'work-horse' vehicle which can serve as an excellent platform for this research. It was further concluded that the performance of a blended wing body configuration surpassed that of a lifting body design for typical X-24C missions. The cost of a two vehicle program, less engines, B-52 modification and contractor support after delivery, can be kept within $70M (in Jan. 1976 dollars).

Combs, H. G.↗
NASA NTRS2013

Summary of Data from the Fifth AIAA CFD Drag Prediction Workshop

Results from the Fifth AIAA CFD Drag Prediction Workshop (DPW-V) are presented. As with past workshops, numerical calculations are performed using industry-relevant geometry, methodology, and test cases. This workshop focused on force/moment predictions for the NASA Common Research Model wing-body configuration, including a grid refinement study and an optional buffet study. The grid refinement study used a common grid sequence derived from a multiblock topology structured grid. Six levels of refinement were created resulting in grids ranging from 0.64x10(exp 6) to 138x10(exp 6) hexahedra - a much larger range than is typically seen. The grids were then transformed into structured overset and hexahedral, prismatic, tetrahedral, and hybrid unstructured formats all using the same basic cloud of points. This unique collection of grids was designed to isolate the effects of grid type and solution algorithm by using identical point distributions. This study showed reduced scatter and standard deviation from previous workshops. The second test case studied buffet onset at M=0.85 using the Medium grid (5.1x106 nodes) from the above described sequence. The prescribed alpha sweep used finely spaced intervals through the zone where wing separation was expected to begin. Some solutions exhibited a large side of body separation bubble that was not observed in the wind tunnel results. An optional third case used three sets of geometry, grids, and conditions from the Turbulence Model Resource website prepared by the Turbulence Model Benchmarking Working Group. These simple cases were intended to help identify potential differences in turbulence model implementation. Although a few outliers and issues affecting consistency were identified, the majority of participants produced consistent results.

Levy, David W.↗
NASA NTRS2016

Application of a Full Reynolds Stress Model to High Lift Flows

A recently developed second-moment Reynolds stress model was applied to two challenging high-lift flows: (1) transonic flow over the ONERA M6 wing, and (2) subsonic flow over the DLR-F11 wing-body configuration from the second AIAA High Lift Prediction Workshop. In this study, the Reynolds stress model results were contrasted with those obtained from one- and two{equation turbulence models, and were found to be competitive in terms of the prediction of shock location and separation. For an ONERA M6 case, results from multiple codes, grids, and models were compared, with the Reynolds stress model tending to yield a slightly smaller shock-induced separation bubble near the wing tip than the simpler models, but all models were fairly close to the limited experimental surface pressure data. For a series of high-lift DLR{F11 cases, the range of results was more limited, but there was indication that the Reynolds stress model yielded less-separated results than the one-equation model near maximum lift. These less-separated results were similar to results from the one-equation model with a quadratic constitutive relation. Additional computations need to be performed before a more definitive assessment of the Reynolds stress model can be made.

Lee-Rausch, E. M.↗
NASA NTRS2007

In-Flight Subsonic Lift and Drag Characteristics Unique to Blunt-Based Lifting Reentry Vehicles

Lift and drag measurements have been analyzed for subsonic flight conditions for seven blunt-based reentry-type vehicles. Five of the vehicles are lifting bodies (M2-F1, M2-F2, HL-10, X-24A, and X-24B) and two are wing-body configurations (the X-15 and the Space Shuttle Enterprise). Base pressure measurements indicate that the base drag for full-scale vehicles is approximately three times greater than predicted by Hoerner's equation for three-dimensional bodies. Base drag and forebody drag combine to provide an optimal overall minimum drag (a drag "bucket") for a given configuration. The magnitude of this optimal drag, as well as the associated forebody drag, is dependent on the ratio of base area to vehicle wetted area. Counter-intuitively, the flight-determined optimal minimum drag does not occur at the point of minimum forebody drag, but at a higher forebody drag value. It was also found that the chosen definition for reference area for lift parameters should include the projection of planform area ahead of the wing trailing edge (i.e., forebody plus wing). Results are assembled collectively to provide a greater understanding of this class of vehicles than would occur by considering them individually.

Saltzman, Edwin J.↗
NASA NTRS1989

Euler/Navier-Stokes calculations of transonic flow past fixed- and rotary-wing aircraft configurations

Computational fluid dynamics has an increasingly important role in the design and analysis of aircraft as computer hardware becomes faster and algorithms become more efficient. Progress is being made in two directions: more complex and realistic configurations are being treated and algorithms based on higher approximations to the complete Navier-Stokes equations are being developed. The literature indicates that linear panel methods can model detailed, realistic aircraft geometries in flow regimes where this approximation is valid. As algorithms including higher approximations to the Navier-Stokes equations are developed, computer resource requirements increase rapidly. Generation of suitable grids become more difficult and the number of grid points required to resolve flow features of interest increases. Recently, the development of large vector computers has enabled researchers to attempt more complex geometries with Euler and Navier-Stokes algorithms. The results of calculations for transonic flow about a typical transport and fighter wing-body configuration using thin layer Navier-Stokes equations are described along with flow about helicopter rotor blades using both Euler/Navier-Stokes equations.

Deese, J. E.↗
NASA NTRS2017

DPW-VI Results Using FUN3D with Focus on k-kL-MEAH2015 (k-kL) Turbulence Model

The Common Research Model wing-body configuration is investigated with the k-kL-MEAH2015 turbulence model implemented in FUN3D. This includes results presented at the Sixth Drag Prediction Workshop and additional results generated after the workshop with a nonlinear Quadratic Constitutive Relation (QCR) variant of the same turbulence model. The workshop provided grids are used, and a uniform grid refinement study is performed at the design condition. A large variation between results with and without a reconstruction limiter is exhibited on "medium" grid sizes, indicating that the medium grid size is too coarse for drawing conclusions in comparison with experiment. This variation is reduced with grid refinement. At a fixed angle of attack near design conditions, the QCR variant yielded decreased lift and drag compared with the linear eddy-viscosity model by an amount that was approximately constant with grid refinement. The k-kL-MEAH2015 turbulence model produced wing root junction flow behavior consistent with wind tunnel observations.

Abdol-Hamid, K. S.↗