Search NASA⌕ Search

SEARCH · Search NASA

Results for “Youngs Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Mechanical properties of 3C silicon carbide

The residual stress and Young's modulus of 3C silicon carbide (SiC) epitaxial films deposited on silicon substrates were measured by load-deflection measurements using suspended SiC diaphragms fabricated with silicon micromachining techniques. The film's residual stress was tensile and averaged 274 MPa while the in-plane Young's modulus averaged 394 GPa. In addition, the bending moment due to the residual stress variation through the thickness of the film was determined by measuring the deflection of free-standing 3C-SiC cantilever beams. The bending moment was in the range of 2.6 x 10 exp -8 -4.2 x 10 exp-8 N m.

Tong, Lijun↗
DOE OSTI2020

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗
NASA NTRS1978

An evaluation of the sandwich beam in four-point bending as a compressive test method for composites

The experimental phase of the study included compressive tests on HTS/PMR-15 graphite/polyimide, 2024-T3 aluminum alloy, and 5052 aluminum honeycomb at room temperature, and tensile tests on graphite/polyimide at room temperature, -157 C, and 316 C. Elastic properties and strength data are presented for three laminates. The room temperature elastic properties were generally found to differ in tension and compression with Young's modulus values differing by as much as twenty-six percent. The effect of temperature on modulus and strength was shown to be laminate dependent. A three-dimensional finite element analysis predicted an essentially uniform, uniaxial compressive stress state in the top flange test section of the sandwich beam. In conclusion, the sandwich beam can be used to obtain accurate, reliable Young's modulus and Poisson's ratio data for advanced composites; however, the ultimate compressive stress for some laminates may be influenced by the specimen geometry.

Shuart, M. J.↗
NASA NTRS1987

Invar and Elinvar type amorphous Fe-Cr-B alloys with high corrosion resistance

Amorphous (Fe(1-x)Cr(x))85B15 alloys (x = 0 to 0.15) were prepared from the melts by rapid quenching using a single roller techinque, and their Invar and Elinvar characteristics and corrosion resistance were investigated. With an increase in chromium content the Curie temperature and the saturation magnetic moment per iron atom decreased monotonically, while the crystallization temperature incresed gradually. The thermal expansion coefficient alpha around room temperature became slightly larger with increasing chromium content. Nevertheless, these amorphous alloys exhibited excellent Invar characteristics below the Curie temperature. The value of Young's modulus increased remarkably in a relatively low magnetic field and then saturated at a field of about 80 kA/m, showing a large delta E effect. Its value as well as a longitudinal linear magnetostriction became smaller with an increase in chromium content. The temperature coefficient of Young's modulus changed from postive to negative, and the temperature range showing the Elinvar characteristics became narrower with chromium content. The temperature coefficient of delay time determined from the values of alpha and e was very small. The corrosion resistance of these alloys was extremely improved by chromium addition.

Kikuci, M.↗
DOE OSTI2021

Skin-like low-noise elastomeric organic photodiodes

Stretchable optoelectronics made of elastomeric semiconductors could enable the integration of intelligent systems with soft materials, such as those of the biological world. Organic semiconductors and photodiodes have been engineered to be elastomeric; however, for photodetector applications, it remains a challenge to identify an elastomeric bulk heterojunction (e-BHJ) photoactive layer that combines a low Young’s modulus and a high strain at break that yields organic photodiodes with low electronic noise values and high photodetector performance. Here, a blend of an elastomer, a donor-like polymer, and an acceptor-like molecule yields a skin-like e-BHJ with a Young’s modulus of a few megapascals, comparable to values of human tissues, and a high strain at break of 189%. Elastomeric organic photodiodes based on e-BHJ photoactive layers maintain low electronic noise current values in the tens of femtoamperes range and noise equivalent power values in the tens of picowatts range under at least 60% strain.

42 ENGINEERING↗
DOE OSTI2020

Understanding the origin of softness in structurally tailored and engineered macromolecular (STEM) gels: A DPD study

Structurally tailored and engineered macromolecular (STEM) gels are polymer networks containing a primary network (the “STEM-0” gel) and side chains that are anchored to this network (forming the “STEM-1” gel). The ability to vary the features of the side chains provides a robust means of tailoring the macroscopic properties of the material. We use dissipative particle dynamics (DPD) simulations to determine the mechanical response of STEM-1 gels to uniaxial compression for various values of the side chain length, n sc . While the Young’s modulus of the material is significantly decreased with increasing n sc (at a fixed density of grafted side chains), above a certain saturation value, increasing n sc does not lead to any further softening of the sample. Using the simulations, we calculate the relevant stresses, which are related to the Young’s modulus and the number of entanglements in the network. We show that the backbone chains become more spread out upon addition of sidechains, leading to a decrease in the physical entanglements between backbone segments. This observation accounts for the decrease of stress in the backbone network and the softening of the networks through the addition of sidechains. For long chains, however, the number density of physical crosslinks between side chains is independent of side chain length; this observation explains the observed stress saturation in the STEM-1 gels. Our approach allows us to correlate the molecular architecture of the gels to the resultant macroscopic mechanical behavior and provide guidelines for fabricating STEM gels with well-defined mechanical properties, which allow the materials to be used for a variety of applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗
NASA NTRS1999

High Temperature Mechanical Characterization and Analysis of Al2O3 /Al2O3 Composition

Sixteen ply unidirectional zirconia coated single crystal Al2O3 fiber reinforced polycrystalline Al2O3 was tested in uniaxial tension at temperatures to 1400 C in air. Fiber volume fractions ranged from 26 to 31%. The matrix has primarily open porosity of approximately 40%. Theories for predicting the Young's modulus, first matrix cracking stress, and ultimate strength were applied and evaluated for suitability in predicting the mechanical behavior of Al2O3/Al2O3 composites. The composite exhibited pseudo tough behavior (increased area under the stress/strain curve relative to monolithic alumina) from 22 to 1400 C. The rule-of-mixtures provides a good estimate of the Young's modulus of the composite using the constituent properties from room temperature to approximately 1200 C for short term static tensile tests in air. The ACK theory provides the best approximation of the first matrix cracking stress while accounting for residual stresses at room temperature. Difficulties in determining the fiber/matrix interfacial shear stress at high temperatures prevented the accurate prediction of the first matrix cracking stress above room temperature. The theory of Cao and Thouless, based on Weibull statistics, gave the best prediction for the composite ultimate tensile strength.

Gyekenyesi, John Z.↗
DOE OSTI2022

Mechanical Properties of Functionally Graded Concrete Lining for Deep Underground Structures

With the mining depth of coal resources increasing, the thickness of traditional lining for deep mines becomes large. The bearing capacity of the outer lining cannot be fully utilized, so a new type of functionally graded lining structure (FGL) with radial Young’s modulus varying in gradient is proposed. In this study, through theoretical analysis and numerical simulation, the mechanical properties of the functionally graded lining were studied, including the characteristics of the elastic working state and the ultimate bearing state. The influences of the structural parameters of the functionally graded lining, including the inner radius, the thickness, Young’s modulus, the compressive strength of the concrete, Poisson’s ratio, and the number of layers on the mechanical properties were analyzed. The calculation formula of the ultimate bearing capacity of the lining and the calculation formula of the maximum tangential strain at the time of lining failure were put forward. The accuracy of the formula was verified by comparing with the numerical simulation results. The research results provide the basis for the construction of the design theory of a functionally graded lining structure and have great engineering significance for the construction of the kilometer-deep mines in the future.

Li, De-Chun↗
DOE OSTI2017

Temperature dependent elastic properties of γ-phase U – 8 wt% Mo

Polycrystalline elastic moduli and stiffness tensor components of γ-phase U – 8 wt% Mo have been determined by resonant ultrasound spectroscopy in the temperature range of 25-650°C. The ambient temperature elastic properties are compared to results measured via other experimental methods and show reasonable agreement, though there is considerable variation of these properties within the literature at both the U – 8 wt% Mo composition and as a function of Mo concentration. The Young’s modulus of U – 8 wt% Mo measured in this study decreases steadily with temperature at a rate that is slower than trends previously observed at similar Mo concentrations, though the difference is not statistically significant. This first measurement of the temperature dependent elastic stiffness tensor of a polycrystalline U-Mo alloy clarifies that the behavior of the Young’s modulus is due to a strongly weakening C 11 polycrystalline stiffness tensor component, along with milder decreases in C 12 and C 44 . The unique partially auxetic properties recently predicted for singlecrystalline U-Mo are discussed in regard to their possible impact on the polycrystalline behavior of the alloy.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2016

Impact of Elastic Moduli in Tension and Compression in Geomaterials

Predicting the long-term integrity of caprock is essential for determining the viability of carbon sequestration. Accurate prediction requires incorporating knowledge about small-scale, subcritical fracture and how they contribute to developing micro and macro-cracks. Tests such as short rod, notched three-point bending (N3PB), cylinder splitting, double torsion, etc. are used to determine the physical characteristics of material. Unlike other materials such as metals, geomaterials have different moduli in tension than compression. This study compares the effects of separate tension and compression moduli on simulations in Abaqus for the N3PB test. Previous models of N3PB created by Rhinehart et al. and Borowski have struggled to create results that accurately portrayed experimental results. Borowski found that previous models with only one value for Young's modulus improved when two moduli were used though it was difficult to determine regions of tension and compression prior to simulation. This study develops an Abaqus subroutine written in Fortran to dynamically reassign material properties as the simulation progresses and produces simulation results capable of much better replication of experimental data. However, the accuracy of the model heavily depends on accurate determination of the Young's modulus in tension.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Preventing Thin Film Dewetting via Graphene Capping

A monolayer 2D capping layer with high Young's modulus is shown to be able to effectively suppress the dewetting of underlying thin films of small organic semiconductor molecule, polymer, and polycrystalline metal, respectively. To verify the universality of this capping layer approach, the dewetting experiments are performed for single‐layer graphene transferred onto polystyrene (PS), semiconducting thienoazacoronene (EH‐TAC), gold, and also MoS 2 on PS. Thermodynamic modeling indicates that the exceptionally high Young's modulus and surface conformity of 2D capping layers such as graphene and MoS 2 substantially suppress surface fluctuations and thus dewetting. As long as the uncovered area is smaller than the fluctuation wavelength of the thin film in a dewetting process via spinodal decomposition, the dewetting should be suppressed. The 2D monolayer‐capping approach opens up exciting new possibilities to enhance the thermal stability and expands the processing parameters for thin film materials without significantly altering their physical properties.

Cao, Peigen↗
DOE OSTI2018

Characterisation of the spatial variability of material properties of Gilsocarbon and NBG-18 using random fields

Graphite is a candidate material for Generation IV concepts and is used as a moderator in Advanced Gas-cooled Reactors (AGR) in the UK. Spatial material variability is present within billets causing different material property values between different components. Variations in material properties and irradiation effects can produce stress concentrations and diverse mechanical responses in a nuclear reactor graphite core. In order to characterise the material variability, geostatistical techniques called variography and random field theory were adapted for studying the density and Young's modulus of a billet of Gilsocarbon and NBG-18 graphite grades. Variography is a technique for estimating the distance over which material property values have significant spatial correlation, known as the scale of fluctuation or spatial correlation length. The paper uses random field theory to create models that mimic the original spatial and statistical distributions of the original data set. This study found different values of correlation length for density and Young's modulus around the edges of a Gilsocarbon billet, while in the case of NBG-18, similar correlation lengths where found across the billet. Furthermore examples of several random fields are given to reproduce the spatial patterns and values found in the original data.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Constitutive Modeling of the Mechanical Properties of Optical Fibers

Micromechanical modeling of the composite mechanical properties of optical fibers was conducted. Good agreement was obtained between the values of Young's modulus obtained by micromechanics modeling and those determined experimentally for a single mode optical fiber where the wave guide and the jacket are physically coupled. The modeling was also attempted on a polarization-maintaining optical fiber (PANDA) where the wave guide and the jacket are physically decoupled, and found not to applicable since the modeling required perfect bonding at the interface. The modeling utilized constituent physical properties such as the Young's modulus, Poisson's ratio, and shear modulus to establish bounds on the macroscopic behavior of the fiber.

Moeti, L.↗
DOE OSTI2016

Method of tissue repair using a composite material

A composite biocompatible hydrogel material includes a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa. A calcium comprising salt is disposed in at least some of the pores. The porous polymer matrix can comprise cellulose, including bacterial cellulose. The composite can be used as a bone graft material. A method of tissue repair within the body of animals includes the steps of providing a composite biocompatible hydrogel material including a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa, and inserting the hydrogel material into cartilage or bone tissue of an animal, wherein the hydrogel material supports cell colonization in vitro for autologous cell seeding.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2015

FP-LAPW based investigation of structural, electronic and mechanical properties of CePb{sub 3} intermetallic compound

A theoretical study of structural, electronic, elastic and mechanical properties of CePb{sub 3} intermetallic compound has been investigated systematically using first principles density functional theory. The calculations are carried out within the three different forms of generalized gradient approximation (GGA) and LSDA for the exchange correlation potential. The ground state properties such as lattice parameter (a{sub 0}), bulk modulus (B) and its pressure derivative (B′) are calculated and obtained lattice parameter of this compound shows well agreement with the experimental results. We have calculated three independent second order elastic constants (C{sub 11}, C{sub 12} and C{sub 44}), which has not been calculated and measured yet. From energy dispersion curves, it is found that the studied compound is metallic in nature. Ductility of this compound is analyzed using Pugh’s criteria and Cauchy's pressure (C{sub 11}-C{sub 12}). The mechanical properties such as Young's modulus, shear modulus, anisotropic ratio, Poison's ratio have been calculated for the first time using the Voigt–Reuss–Hill (VRH) averaging scheme. The average sound velocities (v{sub m}), density (ρ) and Debye temperature (θ{sub D}) of this compound are also estimated from the elastic constants.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrasonic characterization of material heterogeneities in stainless steel components produced by laser powder bed fusion

We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.

36 MATERIALS SCIENCE↗