SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Airfoil design for testing in 0.3-m Transonic Cryogenic Tunnel was symmetrical supercritical shape, consistent with flat-bond-plane bonding-and-channeling technology that had been developed. Technique offers greatly increased flexibility in orifice and pressure-channel layout.
Effects of blown jets on the lift and drag of cambered elliptical airfoils are described. Performance changes due to a splitter plate attached to the lower surface of an elliptical airfoil near the trailing edge with and without blowing are indicated. Lift and drag characteristics of airfoils with two blown jets are compared with airfoils with single blowing jets. Airfoil designs that vary the location of a second jet relative to a fixed jet are described.
A review of natural laminar flow (NLF) flight experiences over the period from the 1930's to the present has been given to provide information on the achievability and maintainability of NLF in typical airplane operating environments. Significant effects of loss of laminar flow on airplane performance have been observed for several airplanes, indicating the importance of providing information on these changes to laminar flow airplane operators. Significant changes in airplane stability and control and maximum lift were observed in flight experiments with the loss of laminar flow. However, these effects can be avoided by proper selection of airfoils. Conservative laminar flow airfoil designs should be employed which do not experience significant loss of lift (caused by flow separation) upon the loss of laminar flow. Mechanisms have been observed for the effects of insect accumulation, flight through clouds and precipitation, and propeller slipstreams on laminar flow behavior. Fixed transition testing, in addition to free transition testing, is recommended as a new standard procedure for airplanes with surfaces designed to support laminar flow.
The present status of various types of low-Reynolds number aerodynamics research being conducted at the Fluid Dynamics Branch of NASA Langley Research Center is reviewed. The facilities, testing techniques, airfoil design, and experimental verification are addressed, and ongoing studies of laminar separation bubbles, boundary layer stability and transition control, and low-Reynolds number juncture flow are discussed. The possibility of improving vehicle characteristics at low Reynolds numbers and the general trends of the most promising research in these areas are examined.
Turbine airfoil design, materials, and cooling system management are variables which, when optimized, can contribute to longer turbine component lives. These advancements have been identified as redesign techniques to improve the turbine fatigue life of the SSME High Pressure Fuel Turbopump. This paper discusses the general program approach toward improving turbine fatigue life.
The purpose of this program is to develop life prediction models for anisotropic materials used in gas turbine airfoils. In the base portion of the program, two coated single crystal alloys are being tested. They are PWA 286 overlay coated and PWA 273 aluminide coated PWA 1480 and PWA 286 overlay coated Alloy 185. Viscoplastic constitutive models for these materials are also being developed to predict the cyclic stress-strain histories required for life prediction of the lab specimens and actual airfoil designs.
The goal is to accurately predict the characteristics of the laminar separation bubble and its effects on airfoil performance. Toward this end, a computational model of the separation bubble was developed and incorporated into the Eppler and Somers airfoil design and analysis program. Thus far, the focus of the research was limited to the development of a model which can accurately predict situations in which the interaction between the bubble and the inviscid velocity distribution is weak, the so-called short bubble. A summary of the research performed in the past nine months is presented. The bubble model in its present form is then described. Lastly, the performance of this model in predicting bubble characteristics is shown for a few cases.
The Tollmien-Schlichting (TS) instability is a time-dependence instability which can lead to transition of laminar boundary layers on airfoils. A comparison of theoretical predictions and experimental observations of the TS instability on the NLF(1)-0414F airfoil designed by Viken and Pfenninger. The theoretical predictions were obtained using the SALLY stability code. Test results, from the same hot films that were used to detect transition, revealed that TS waves could be detected by the hot films if the hot-film signal was adequately modified.
The aerodynamic design of a supersonic oblique flying wing is strongly influenced by the requirement that passengers must be accommodated inside the wing. It was revealed that thick oblique wings of very high sweep angle can be efficient at supersonic speeds when transonic normal Mach numbers are allowed on the upper surface of the wing. The goals were motivated by the ability to design a maximum thickness, minimum size oblique flying wing. A 2-D Navier-Stokes solver was used to design airfoils up to 16 percent thickness with specified lift, drag and pitching moment. A new method was developed to calculate the required pressure distribution on the wing based on the airfoil loading, normal Mach number distribution and theoretical knowledge of the minimum drag of oblique configurations at supersonic speeds. The wing mean surface for this pressure distribution was calculated using an inverse potential flow solver. The lift to drag ratio of this wing was significantly higher than that of a comparable delta wing for cruise speeds up to Mach 2.
Experiments are presented which were conducted on flow fields produced by a circulation control airfoil utilizing the Coanda effect at the trailing edge. The application of holographic interferometry to obtain both visualization and quantitative data on the flow field about a circulation control airfoil at transonic flow speed is covered. A brief description of the flow model and measurement techniques is given. The data reduction procedure, results, and interpretation are presented. The results have provided a good deal of information on the character of the flow field, particularly in the neighborhood of the trailing edge. As to the airfoil design, it is apparent that improved performance can be achieved if jet detachment is delayed. Another design improvement would involve the development of an optimum trailing-edge shape for the expected operating Mach and Reynolds number ranges.
The viscous airfoil design analysis code XFOIL was extended to allow optimization using conformal mapping coefficients as design variables. The optimization technique used was the Steepest Descent method applied to a Penalty Function. The gradients of the aerodynamic variables with respect to the design variables were cheaply calculated as by-products of XFOIL's integral boundary layer Newton solver. The speed of the optimization process further increased by updating the Newton system boundary layer variables after each optimization step using the available gradient information. Two examples are presented.
Wind tunnel tests were performed on a two-dimensional model of the SM701 airfoil designed for use on the World Class gliders. The test covered a range of Reynolds numbers from 500,000 to 1.7 million. Aerodynamic forces and moments were measured with an external balance. Momentum loss method measurements of the section drag coefficient were also made. Flow visualization techniques provided information on transition from laminar to turbulent flow. Lift, drag, and pitching moment were analyzed and comparisons were made with predicted and previously obtained experimental data. The effects of V-tape turbulators for use in turbulent drag reduction were studied. The performance of a 25 percent chord aileron deflected through plus or minus 20 degrees was researched. The model was designed, constructed, and tested by students at Texas A&M University.
The Thermal/Structural Tailoring of Engine Blades (T/STAEBL) system is a computer code that is able to perform numerical optimizations of cooled jet engine turbine blades and vanes. These optimizations seek an airfoil design of minimum operating cost that satisfies realistic design constraints. This report documents the organization of the T/STAEBL computer program, its design and analysis procedure, its optimization procedure, and provides an overview of the input required to run the program, as well as the computer resources required for its effective use. Additionally, usage of the program is demonstrated through a validation test case.
Marta Bohn-Meyer discusses the cooperative research between Rockwell Industries and NASA research facilities in their effort to optimize and maintain the supersonic laminar flow on the F-16XL aircraft. Research on the airfoil design, chord optimization, introduction of a suction feature to maintain pressure distribution, and CFD, both theoretical and actual phenomena, are discussed. Bohn-Meyer discusses the difference between supersonic and subsonic laminar flow, cross flow, reasons behind using this particular F-16 aircraft for this research, and the future of this ongoing research, including the data base that investigators are building from wind tunnel data and in-flight validation.
This paper describes a new geometric analysis procedure for wing sections. This procedure is based on the normal mode analysis for continuous functions. A set of special shape functions is introduced to represent the geometry of the wing section. The generators of the NACA 4-digit airfoils were included in this set of shape functions. It is found that the supercritical wing section, Korn airfoil, could be well represented by a set of ten shape functions. Preliminary results showed that the number of parameters to define a wing section could be greatly reduced to about ten. Hence, the present research clearly advances the airfoil design technology by reducing the number of design variables.
Thin thermal barrier coatings for protecting aircraft turbine section airfoils are examined. The discussion focuses on those advances that led first to their use for component life extension and more recently as an integral part of airfoil design. It is noted that development has been driven by laboratory rig and furnace testing corroborated by engine testing and engine field experience. The technology has also been supported by performance modeling to demonstrate benefits and life modeling for mission analysis. Factors which have led to the selection of the current state-of-the-art plasma sprayed and physical vapor deposited zirconia-yttria/MCrAlY TBC's is emphasized in addition to observations fundamentally related to their behavior. Current directions in research into thermal barrier coatings and recent progress at NASA is also noted.
LAYER computer program performs thermomechanical-fatigue-life prediction for coated, nickel-based anisotropic materials. Intended to provide gas-turbine-airfoil designers with means to accurately project service lifetimes. Written in FORTRAN 77.
NASA-Lewis and NASA-Ames have sponsored a series of studies over the last few years to identify key high speed rotorcraft propulsion and airframe technologies. NASA concluded from these studies that for near term aircraft with cruise speeds up to 450 kt, tilting rotor rotorcraft concepts are the most economical and technologically viable. The propulsion issues critical to tilting rotor rotorcraft are: (1) high speed cruise propulsion system efficiency and (2) adequate power to hover safely with one engine inoperative. High speed cruise propeller efficiency can be dramatically improved by reducing rotor speed, yet high rotor speed is critical for good hover performance. With a conventional turboshaft, this wide range of power turbine operating speeds would result in poor engine performance at one or more of these critical operating conditions. This study identifies several wide speed range turboshaft concepts, and analyzes their potential to improve performance at the diverse cruise and hover operating conditions. Many unique concepts were examined, and the selected concepts are simple, low cost, relatively low risk, and entirely contained within the power turbine. These power turbine concepts contain unique, incidence tolerant airfoil designs that allow the engine to cruise efficiently at 51 percent of the hover rotor speed. Overall propulsion system efficiency in cruise is improved as much as 14 percent, with similar improvements in engine weight and cost. The study is composed of a propulsion requirement survey, a concept screening study, a preliminary definition and evaluation of selected concepts, and identification of key technologies and development needs. In addition, a civil transport tilting rotor rotorcraft mission analysis was performed to show the benefit of these concepts versus a conventional turboshaft. Other potential applications for this technology are discussed.