SEARCH · Search NASA

Results for “axial”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Analytical and Experimental Study of Flow Through an Axial Turbine Stage with a Nonuniform Inlet Radial Temperature Profile

Results are presented for a typical nonuniform inlet radial temperature profile through an advanced single-stage axial turbine and compared with the results obtained for a uniform profile. Gas temperature rises of 40 K to 95 K are predicted at the hub and tip corners at the trailing edges of the pressure surfaces in both the stator and rotor due to convection of hot fluid from the mean by the secondary flow. The inlet temperature profile is shown to be mixed out at the rotor exit survey plane (2.3 axial chords downstream of the rotor trailing edge) in both the analysis and the experiment. The experimental rotor exit angle profile for the nonuniform inlet temperature profile indicates underturning at the tip caused by increased clearance. Severe underturning also occurs at the mean, both with and without the nonuniform inlet temperature profile. The inviscid rotational flow code used in the analysis fails to predict the underturning at the mean, which may be caused by viscous effects.

Schwab, J. R.↗

NASA NTRS1982

Advanced axial field D.C. motor development for electric passenger vehicle

A wound-field axial-flux dc motor was developed for an electric vehicle drive system. The motor is essentially an axial-flux version of the classical Gramme-ring winding motor, but the active conductors are recessed into slots cut into the two opposite faces of the laminated tape-wound core ring. Three motors were built and tested in the program. The second (functional) model was a six-pole machine which weighed 88.5 kg. It developed 16.9 km (33.0 hp), and a max speed of 4800 rpm. Full load efficiency was 92% and predicted SAE D-cycle efficiency was 88%. The last engineering) model was a 4-pole machine with compoles, allowing a weight reduction to 45 kg (100 lbs.) while addressing some manufacturability problems. The engineering model was rated at 13.2 kw (17.6 hp) at 3000 rpm, with a peak power of 19.8 km (26.4 hp) and a max speed of 7200 rpm. Initial test results on this motor showed poor commutation and efficiency; the program was terminated without resolution of these problems.

Jones, W. J.↗

NASA NTRS1978

User's Manual for Thermal Analysis Program of Axially Grooved Heat Pipe (HTGAP)

A computer program that numerically predicts the steady state temperature distribution inside an axially grooved heat pipe wall for a given groove geometry and working fluid under various heat input and output modes is described. The program computes both evaporator and condenser film coefficients. The program is able to handle both axisymmetric and nonaxisymmetric heat transfer cases. Non-axisymmetric heat transfer results either from non-uniform input at the evaporator or non-uniform heat removal from the condenser, or from both. The presence of a liquid pool in the condenser region under one-g condition also causes non-axisymmetric heat transfer, and its effect on the pipe wall temperature distribution is included in the present program. The hydrodynamic aspect of an axially grooved heat pipe is studied in the Groove Analysis Program (GAP). The present thermal analysis program assumes that the GAP program (or other similar programs) is run first so that the heat transport limit and optimum fluid charge of the heat pipe are known a priori.

Kamotani, Y.↗

NASA NTRS1983

A comprehensive method for preliminary design optimization of axial gas turbine stages. II - Code verification

The present effort represents an extension of previous work wherein a calculation model for performing rapid pitchline optimization of axial gas turbine geometry, including blade profiles, is developed. The model requires no specification of geometric constraints. Output includes aerodynamic performance (adiabatic efficiency), hub-tip flow-path geometry, blade chords, and estimates of blade shape. Presented herein is a verification of the aerodynamic performance portion of the model, whereby detailed turbine test-rig data, including rig geometry, is input to the model to determine whether tested performance can be predicted. An array of seven (7) NASA single-stage axial gas turbine configurations is investigated, ranging in size from 0.6 kg/s to 63.8 kg/s mass flow and in specific work output from 153 J/g to 558 J/g at design (hot) conditions; stage loading factor ranges from 1.15 to 4.66.

Jenkins, R. M.↗

NASA NTRS1983

Martian great dust storms - Interpretive axially symmetric models

The Martian great dust storms are presently considered in light of the Schneider (1977) simplified theory of steady, nearly inviscid, thermally forced and axially symmetric atmospheric motions. A highly idealized calculation of atmospheric response to heating that is concentrated in a small latitude band is conducted, leading to the identification of qualitatively different local and global response regimes. Idealized model results indicate that subtropical latitudes are favored for the initiation of a dust-raising global dust storm. The steady, axially symmetric Martian response to solar forcing and modification to this response through an additional, latitudinally localized heat source are also discussed, and it is suggested that transition behavior similar to that of the more idealized model is to be expected in this case as well.

Schneider, E. K.↗

NASA NTRS1983

Analytical and experimental study of flow through an axial turbine stage with a nonuniform inlet radial temperature profile

Schwab, J. R.↗

NASA NTRS1983

Wall boundary layer development near the tip region of an IGV of an axial flow compressor

The annulus wall boundary layer inside the blade passage of the inlet guide vane (IGV) passage of a low-speed axial compressor stage was measured with a miniature five-hole probe. The three-dimensional velocity and pressure fields were measured at various axial and tangential locations. Limiting streamline angles and static pressures were also measured on the casing of the IGV passage. Strong secondary vorticity was developed. The data were analyzed and correlated with the existing velocity profile correlations. The end wall losses were also derived from these data.

Lakshminarayana, B.↗

NASA NTRS1983

A pressurized cylindrical shell with a fixed end which contains an axial part-through or through crack

A cylindrical shell having a very stiff and plate or a flange is considered. It is assumed that near the end the cylinder contains an axial flaw which may be modeled as a part through surface crack or a through crack. The effect of the end constraining on the stress intensity factor which is the main fracture mechanics parameter is studied. The applied loads acting on the cylinder are assumed to be axisymmetric. Thus the crack problem under consideration is symmetric with respect to the plane of the crack and consequently only the Mode 1 stress intensity factors are nonzero. With this limitation, the general perturbation problem for a cylinder with a built in end containing an axial crack is considered. Reissner's shell theory is used to formulate the problem. The part through crack problem is treated by using a line spring model. In the case of a crack tip terminating at the fixed end it is shown that the integral equations of the shell problem has the same generalized Cauchy kernel as the corresponding plane stress elasticity problem.

Yahsi, O. S.↗

NASA NTRS1983

Simulation of the Galileo spacecraft axial - Delta-V algorithm

Preliminary results are presented from the analysis of the Galileo spacecraft axial delta-V algorithm. The Galileo spacecraft is a dual spin interplanetary spacecraft which will study the four Galilean moons of Jupiter as well as the Jovian environment and atmosphere. In order to achieve orbit about Jupiter and accurately deliver the probe to the planet's upper atmosphere, the Galileo spacecraft must be capable of performing many trajectory corrections or delta-V maneuvers. Twelve 10 Newton thrusters and one 400 Newton engine are utilized for this purpose. There are many maneuver modes and control algorithms available to the spacecraft. In this paper only the analysis of the axial delta-V algorithm will be discussed. The analysis consists of two parts: an analytic study and a simulation study. The analytic results are based on rigid body dynamics, while the simulation includes the first order effect of the flexible magnetometer boom and nutation damper. The simulation utilizes a program developed at JPL which allows flexible body effects to be simulated by modeling a collection of rigid bodies attached together by hinges, springs and dampers. In this preliminary study of the Galileo only two rigid bodies were used in the simulation, but many more can and will be used in the final tests. In this analysis, the algorithm appears to be working correctly and the analytic and simulation results agree very well.

Longuski, J. M.↗

NASA NTRS1984

An improved computer model for prediction of axial gas turbine performance losses

The calculation model performs a rapid preliminary pitchline optimization of axial gas turbine annular flowpath geometry, as well as an initial estimate of blade profile shapes, given only a minimum of thermodynamic cycle requirements. No geometric parameters need be specified. The following preliminary design data are determined: (1) the optimum flowpath geometry, within mechanical stress limits; (2) initial estimates of cascade blade shapes; and (3) predictions of expected turbine performance. The model uses an inverse calculation technique whereby blade profiles are generated by designing channels to yield a specified velocity distribution on the two walls. Velocity distributions are then used to calculate the cascade loss parameters. Calculated blade shapes are used primarily to determine whether the assumed velocity loadings are physically realistic. Model verification is accomplished by comparison of predicted turbine geometry and performance with an array of seven NASA single-stage axial gas turbine configurations.

Jenkins, R. M.↗

NASA NTRS1986

Postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. The postbuckling response of each specimen is typical of axially-compressed cylindrical shells and curved panels in that a severe reduction in load occurs at buckling. Failure of all panels initiated near regions with severe local bending gradients. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical experimental results up to buckling. Measured initial geometric imperfections were included in the postbuckling analysis. Analytically-determined stress distributions in the postbuckling response were used with failure criteria to identify the load level and the location of first-ply failure.

Knight, N. F., Jr.↗

NASA NTRS1986

An exact solution for orbit view-periods from a station on a tri-axial ellipsoidal planet

This paper presents the concise exact solution for predicting view-periods to be observed from a masked or unmasked tracking station on a tri-axial ellipsoidal surface. The new exact approach expresses the azimuth and elevation angles of a spacecraft in terms of the station-centered geodetic topocentric coordinates in an elegantly concise manner. A simple and efficient algorithm is developed to avoid costly repetitive computations in searching for neighborhoods near the rise and set times of each satellite orbit for each station. Only one search for each orbit is necessary for each station. Sample results indicate that the use of an assumed spherical earth instead of an 'actual' tri-axial ellipsoidal earth could introduce an error up to a few minutes in a view-period prediction for circular orbits of low or medium altitude. For an elliptical orbit of high eccentricity and long period, the maximum error could be even larger. The analytic treatment and the efficient algorithm are designed for geocentric orbits, but they should be applicable to interplanetary trajectories by an appropriate coordinates transformation at each view-period calculation. This analysis can be accomplished only by not using the classical orbital elements.

Tang, C. C. H.↗

NASA NTRS1986

Unsteady Flows in a Single-Stage Transonic Axial-Flow Fan Stator Row

Measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan were acquired using a laser anemometer. Measurements were obtained on axisymmetric surfaces located at 10 and 50 percent span from the shroud, with the fan operating at maximum efficiency at design speed. The ensemble-average and variance of the measured velocities are used to identify rotor-wake-generated (deterministic) unsteadiness and turbulence, respectively. Correlations of both deterministic and turbulent velocity fluctuations provide information on the characteristics of unsteady interactions within the stator row. These correlations are derived from the Navier-Stokes equation in a manner similar to deriving the Reynolds stress terms, whereby various averaging operators are used to average the aperiodic, deterministic, and turbulent velocity fluctuations which are known to be present in multistage turbomachines. The correlations of deterministic and turbulent velocity fluctuations throughout the axial fan stator row are presented. In particular, amplification and attenuation of both types of unsteadiness are shown to occur within the stator blade passage.

Hathaway, Michael D.↗

NASA NTRS1987

Revised NASA axially symmetric ring model for coupled-cavity traveling-wave tubes

A versatile large-signal, two-dimensional computer program is used by NASA to model coupled-cavity travelling-wave tubes (TWTs). In this model, the electron beam is divided into a series of disks, each of which is further divided into axially symmetric rings which can expand and contract. The trajectories of the electron rings and the radiofrequency (RF) fields are determined from the calculated axial and radial space-charge, RF, and magnetic forces as the rings pass through a sequence of cavities. By varying electrical and geometric properties of individual cavities, the model is capable of simulating severs, velocity tapers, and voltage jumps. The calculated electron ring trajectories can be used in designing magnetic focusing and multidepressed collectors. The details of using the program are presented, and results are compared with experimental data.

Wilson, Jeffrey D.↗

NASA NTRS1986

Dynamics During Thrust Maneuvers of Flexible Spinning Satellites with Axial and Radial Booms

The dynamic response to operational maneuvers of spinning symmetric spacecraft with radial and axial booms was analyzed as part of the prelaunch dynamic analysis of the ISEE-3 spacecraft placed in a halo orbit around an Earth-Sun libration point, and later renamed ICE when it was directed to fly-by comet Giacobini-Zinner. The results presented use simple spacecraft models, and frequently give predictions that are good and easily obtained when the results from using a general purpose multibody dynamics program were very time consuming to obtain. Deployment of radial booms, spin-up after partial deployment, stationkeeping, and trajectory changes are analyzed. The latter two can involve both axial thrusting and pulsed radial thrusting once per revolution.

Longman, R. W.↗

NASA NTRS1988

Rotor self-lubricating axial stop

A series of lubricating plugs is located in the stationary backup face adjacent to the axial stop face of a rotating impeller mounted in a turbopump for pumping liquid oxygen or liquid hydrogen. The stop face and the backup face are those surfaces which engage when the axial load on the impeller exceeds the load balancing capability. The plugs have a truncated conical configuration so as to be trapped in the backup face, and are placed at varying radii on the face to provide complete surface lubrication. The plugs may be formed from Teflon, Kel-F or bronze filled Teflon.

Blount, Dale H.↗

NASA NTRS1988

Hydrogen turbines for space power systems: A simplified axial flow gas turbine model

Hydrogen cooled, turbine powered space weapon systems require a relatively simple, but reasonably accurate hydrogen gas expansion turbine model. Such a simplified turbine model would require little computational time and allow incorporation into system level computer programs while providing reasonably accurate volume/mass estimates. This model would then allow optimization studies to be performed on multiparameter space power systems and provide improved turbine mass and size estimates for the various operating conditions (when compared to empirical and power law approaches). An axial flow gas expansion turbine model was developed for these reasons and is in use as a comparative bench mark in space power system studies at Sandia. The turbine model is based on fluid dynamic, thermodynamic, and material strength considerations, but is considered simplified because it does not account for design details such as boundary layer effects, shock waves, turbulence, stress concentrations, and seal leakage. Although the basic principles presented here apply to any gas or vapor axial flow turbine, hydrogen turbines are discussed because of their immense importance on space burst power platforms.

Hudson, Steven L.↗

NASA NTRS1986

The effects of inlet turbulence and rotor/stator interactions on the aerodynamics and heat transfer of a large-scale rotating turbine model. Volume 3: Heat transfer data tabulation 65 percent axial spacing

This is Volume 3 - Heat Transfer Data Tabulation (65 percent Axial Spacing) of a combined experimental and analytical program which was conducted to examine the effects of inlet turbulence on airfoil heat transfer. The experimental portion of the study was conducted in a large-scale (approximately 5X engine), ambient temperature, rotating turbine model configured in both single stage and stage-and-a-half arrangements. Heat transfer measurements were obtained using low-conductivity airfoils with miniature thermocouples welded to a thin, electrically heated surface skin. Heat transfer data were acquired for various combinations of low or high inlet turbulence intensity, flow coefficient, first-stator/rotor axial spacing, Reynolds number and relative circumferential position of the first and second stators.

Dring, R. P.↗