Search NASA⌕ Search

SEARCH · Search NASA

Results for “bandwidth estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Radar detectability of asteroids - A survey of opportunities for 1977 through 1987

The study of asteroids by earth-based radar during the period 1977 to 1987 is discussed. Detection modeling, including backscattering laws, limits of detectability, and in particular, measurement of center frequency, center-to-limb bandwidth, and areal spectral density, is reviewed. The number of detectable objects and detectable events falling into various 5-decibel radar target loss slots is estimated; a total of 60 different asteroids should be observable on about 130 occasions by either the Goldstone or Arecibo radar systems during the decade considered. Furthermore, the detectability margins for many objects should be large enough to permit more refined analysis of the radar spectrograms. Data acquired during the ten-year period may be used to find the radius, average surface roughness, rotation rate, direction of polar axis, and estimates of the Doppler frequency offsets for many of the asteroids. Also, information about radar albedos and orbital parameters may be obtainable in a number of cases.

Jurgens, R. F.↗

Radar RFI at Goldstone DSS 12 and DSS 16

Radio frequency interference (RFI) from the DSS 14 Goldstone Solar System Radar (GSSR) was investigated at DSS 12 and DSS 16 with the goal of assisting in the choice of the location of future DSN antennas. Total power measurements at both locations were made at the S-band carrier frequency of 2320 MHz. X-band measurements at the carrier frequency of 8495 MHz could not be made. Exciter-chain output spectrum and klystron output spectrum measurements were made at S- and X-bands using a probable worst-case modulation of the radar signal (short pseudorandom number (PN) code length and short pulse length). Based on these measurements, it is estimated that RFI levels in the DSN receiving bands at both sites (above 10-deg elevation) would be below -192 dBm for a 1-Hz bandwidth

Slobin, S. D.↗

High-T(sub c) squid application in medicine and geophysics

In the Laboratory a high-T(sub c) one-hole squid was built from Y1Ba2Cu3O(7-x) ceramics obtained by a standard procedure of solid state reaction. The ceramics with critical current density J(sub c) is greater than 100 A/sq cm was selected. In the middle of 10 x 10 x 2 mm ceramics pellet a 0.8 mm hole was drilled in which superconducting loop of the squid was located. Between the hole and the edge of the pellet a cut was mechanically filed out with a bridge inside it connecting the superconducting ring. A scheme of the magnetometer is presented. The resonant frequency shift of the tank circuit, the connection of the squid with this circuit, and the squid inductance are evaluated. One of the most interesting fields of the squid-based magnetometer application is biomagnetism, particularly, the human heart magnetocardiogram measuring. The low-temperature squids were used in this area and many interesting and important scientific results have been obtained. The observations have shown that the main noise contribution was not due to the squid but to the Earth's magnetic field variations, industrial inductions, and mainly to the vibrations caused by liquid nitrogen boiling and by vibrations of the box. Further attempts are needed to reduce the magnetic noise inductions. Nevertheless, the estimations promise the maximum signal/noise relation of the high-T(sub c) squid-magnetocardiometer to be not less than 10:1 in a bandwidth of 60 Hz. Apparently, such resolution would be enough not only for steady cardiogram reading but even for thin structure investigation at average technique application.

Polushkin, V. N.↗

Symbol lock detection in the ARX 2 and Block 5 receivers

The performances of 5 symbol-lock detectors are compared. These detectors are the square-law detector with overlapping (SQOD) and nonoverlapping integrators, the absolute-value detectors with overlapping and nonoverlapping integrators, and the signal-power estimator detector (SPED). The analysis considers various scenarios in which the observation interval is much larger than or equal to the symbol-synchronizer loop bandwidth, and which were not considered in previous analyses. Also, the case of threshold setting in the absence of signal is considered. It is shown, that the SQOD outperforms all others when the threshold is set in the presence of a signal, independent of the relationship between loop bandwidth and observation period. On the other hand, the SPED outperforms all others when the threshold is set in the presence of noise only.

Shihabi, M.↗

High-T(c) squid application in medicine and geophysics

In our laboratory of high-T(sub c), a one-hole squid was built from Y1Ba2Cu3O(7-x) ceramics obtained by a standard procedure of solid state reaction. The ceramics with critical current density J(sub c) is greater than 100 A/sq cm was selected. In the middle of a 10 x 10 x 2 mm ceramics pellet, a 0.8 mm hole was drilled in which the superconducting loop of the squid was located. Between the hole and the edge of the pellet, a cut was mechanically filed out with a bridge inside it connecting the superconducting ring. A scheme of the magnetometer is presented. The resonant frequency shift of the tank circuit, the connection of the squid with this circuit, and the squid inductance are evaluated. One of the most interesting fields of the squid-based magnetometer application is biomagnetism, particularly, the human heart magnetocardiogram measuring. The low-temperature squids were used in this area and many interesting and important scientific results have been obtained. The observations have shown that the main noise contribution was not due to the squid but to the Earth's magnetic field variations, industrial inductions, and mainly to the vibrations caused by liquid nitrogen boiling and by vibrations of the box. Further attempts are needed to reduce the magnetic noise inductions. Nevertheless, the estimations promise the maximum signal/noise relation of the high-T(sub c) squid-magnetocardiometer to be not less than 10:1 in a bandwidth of 60 Hz. Apparently, such resolution would be enough not only for steady cardiogram reading but even for thin structure investigation at average technique application.

Polushkin, V. N.↗

Enhanced Quasiparticle Lifetime in a Superconductor by Selective Blocking of Recombination Phonons with a Phononic Crystal

When quasiparticles in a BCS (Bardeen-Cooper-Schrieffer) superconductor recombine into Cooper pairs, phonons are emitted within a narrow band of energies above the pairing energy at 2 delta. We show that a phonon band gap restricting the escape of recombination phonons from a superconductor can increase the quasiparticle recombination lifetime by more than an order of magnitude. A phonon band gap can be realized and matched to the recombination energy with a phononic crystal, a periodically patterned dielectric membrane. We discuss in detail the nonequilibrium quasiparticle and phonon distributions that arise in a superconductor due to a phonon band gap and a pair-breaking photon signal. Although intrinsically a nonequilibrium effect, the lifetime enhancement in the small-signal regime is remarkably similar to an estimate from an equilibrium formulation. The equilibrium estimate closely follows exp (Omega (sub bg) divided by k (sub B)T (sub b)), where Omega (sub bg) is the phonon band gap energy bandwidth above 2 and T (sub b) is the phonon bath temperature of the coupled electron-phonon system. We discuss the impact of a phononic band gap on the performance of a superconducting circuit element and propose a microwave resonator to measure the enhancement in the quasiparticle lifetime.

Rostem, K.↗

Assessing Fossil Fuel and Feedstock Use in the U.S. Plastics and Rubber Sector: A Supply Chain Analysis

In plastics and rubber manufacturing, fossil fuels are consumed both as an energy source and as feedstocks that are converted to higher-value products. For example, in the manufacture of polyethylene, natural gas is consumed both as a fuel and as a feedstock during ethylene production. In this work, we expand on the U.S. Department of Energy's Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Plastics and Rubber Manufacturing, which quantified onsite fuel consumption and the potential for reducing fuel consumption by increasing energy efficiency in the plastics and rubber sector. The bandwidth study did not quantify fuel consumed upstream in the supply chain or as a feedstock; however, both contribute significantly to a plastic's total fossil fuel requirements. The U.S. Energy Information Administration's 2014 Manufacturing Energy Consumption Survey (MECS) estimates that fossil fuels consumed as feedstocks account for approximately 74% of total fossil fuel consumption in the U.S. plastic resin manufacturing sector (NAICS 325211). We employ the Materials Flows through Industry (MFI) supply chain modeling tool, developed at the National Renewable Energy Laboratory (NREL), to quantify process fuel and feedstock requirements within the supply chains of the same 10 categories of plastics and rubber commodities covered in the DOE bandwidth report. From these results, we identify supply chains that will have a high feedstock requirement even when energy efficiency is increased. We then use MFI to analyze several alternative plastics supply chains, including those utilizing biomass feedstocks and/or polyethylene terephthalate (PET) waste upcycling, to determine if these alternatives can potentially reduce both process fuel and feedstock requirements within the supply chains of interest. This presentation will include a case study comparison of supply chain energy consumption for petroleum-derived and bio-derived fiberglass reinforced plastic involving a novel waste PET upcycling technique recently discovered by NREL researchers.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Multitaper Magnitude‐Squared Coherence for Time Series With Missing Data: Understanding Oscillatory Processes Traced by Multiple Observables

To explore the hypothesis of a common source of variability in two time series, observers may estimate the magnitude-squared coherence (MSC), which is a frequency-domain view of the cross correlation. For time series that do not have uniform observing cadence, MSC can be estimated using Welch's overlapping segment averaging. However, multitaper has superior statistical properties to Welch's method in terms of the tradeoff between bias, variance, and bandwidth. The classical multitaper technique has recently been extended to accommodate time series with underlying uniform observing cadence from which some observations are missing. This situation is common for solar and geomagnetic data sets, which may have gaps due to breaks in satellite coverage, instrument downtime, or poor observing conditions. We demonstrate the scientific use of missing-data multitaper magnitude-squared coherence by detecting known solar mid-term oscillations in simultaneous, missing-data time series of solar Lyman α flux and geomagnetic Disturbance Storm Time index. Due to their superior statistical properties, we recommend that multitaper methods be used for all heliospheric time series with underlying uniform observing cadence.

Astro-statistics techniques (1886)↗

Propagation effects in polarization-gated attosecond soft-X-ray pulse generation

Accurate estimation of the duration of soft-x-ray pulses from high-harmonic generation (HHG) remains challenging given their higher photon energies and broad spectral bandwidth. The carrier-envelope-phase (CEP) dependence of generated soft-x-ray spectra is indicative of attosecond pulse generation, but advanced simulations are needed to infer the pulse duration from such data. Here, we employ macroscopic propagation simulations to reproduce experimental polarization-gated CEP-dependent soft-x-ray spectra. The simulations indicate chirped pulses, which we theoretically find to be compressible in hydrogen plasmas, suggesting this as a viable compression scheme for broadband soft-x-rays from HHG.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Birds and insects as radar targets - A review

A review of radar cross-section measurements of birds and insects is presented. A brief discussion of some possible theoretical models is also given and comparisons made with the measurements. The comparisons suggest that most targets are, at present, better modeled by a prolate spheroid having a length-to-width ratio between 3 and 10 than by the often used equivalent weight water sphere. In addition, many targets observed with linear horizontal polarization have maximum cross sections much better estimated by a resonant half-wave dipole than by a water sphere. Also considered are birds and insects in the aggregate as a local radar 'clutter' source. Order-of-magnitude estimates are given for many reasonable target number densities. These estimates are then used to predict X-band volume reflectivities. Other topics that are of interest to the radar engineer are discussed, including the doppler bandwidth due to the internal motions of a single bird, the radar cross-section probability densities of single birds and insects, the variability of the functional form of the probability density functions, and the Fourier spectra of single birds and insects.

Vaughn, C. R.↗

Measurement of human pilot dynamic characteristics in flight simulation

Fast Fourier Transform (FFT) and Least Square Error (LSE) estimation techniques were applied to the problem of identifying pilot-vehicle dynamic characteristics in flight simulation. A brief investigation of the effects of noise, input bandwidth and system delay upon the FFT and LSE techniques was undertaken using synthetic data. Data from a piloted simulation conducted at NASA Ames Research Center was then analyzed. The simulation was performed in the NASA Ames Research Center Variable Stability CH-47B helicopter operating in fixed-basis simulator mode. The piloting task consisted of maintaining the simulated vehicle over a moving hover pad whose motion was described by a random-appearing sum of sinusoids. The two test subjects used a head-down, color cathode ray tube (CRT) display for guidance and control information. Test configurations differed in the number of axes being controlled by the pilot (longitudinal only versus longitudinal and lateral), and in the presence or absence of an important display indicator called an 'acceleration ball'. A number of different pilot-vehicle transfer functions were measured, and where appropriate, qualitatively compared with theoretical pilot- vehicle models. Some indirect evidence suggesting pursuit behavior on the part of the test subjects is discussed.

Reedy, James T.↗

A Long-Range Precision Ranging System

A technique is presented that may be used for precision real-time continuous range measuring at long ranges. The technique uses a carrier that is phase modulated by a pseudo-random binary sequence. The characteristics of the sequence that make it acquirable are discussed. The general form of a receiver capable of tracking the carrier is given and is shown to be a kind of phase-locked loop. A two-loop system capable of tracking a pseudo-random sequence and its clock is given. The combination of the receiver and the sequence tracking system form a ranging receiver. The power division necessary between the carrier and the sidebands is shown to be determined by the noise bandwidths of the two tracking systems. The bandwidths necessary for tracking space probes and Earth satellites are given and some experiments in radar-tracking Earth satellites are described. Based on these experiments, estimates are made of the useful range of such a system in tracking space probes.

Easterling, Mahlon↗

Parallel visualization and analysis with paraview on a Cray XT4

Scientific data sets produced by modern supercomputers like ORNL's Cray XT 4, Jaguar, can be extremely large, making visualization and analysis more difficult as moving large resultant data to dedicated analysis systems can be prohibitively expensive. We share our continuing work of integrating a parallel visualization system, ParaView, on ORNL's Jaguar system and our efforts to enable extreme scale interactive data visualization and analysis. We will discuss porting challenges and present performance numbers. Jaguar is a Cray XT4 with 7,832 compute nodes each with 4 cores and 8GB of memory, located in Oak Ridge, Tennessee. Jaguar is currently ranked No.8 in the Top 500. Jaguar, and other machines like it, enable increasingly larger data sets. Whether scientists are producing extremely massive data or small data they still have a requirement for analysis. Analysis is often difficult for larger data and it is further complicated when the user is distant to the data. Data sets that are too large to ship and/or analyze on a single desktop require a parallel analysis tool and a high performance computer to run on. Running ParaView interactively on Jaguar is a positive improvement for both local and remote users. We have shown that it is feasible for our user at LANL to visualize his simulation data created on jaguar. Local users may face fewer obstacles and get improved performance, due to their higher bandwidth to Jaguar. For future work, we would like to see higher priority queues that enable interactive visualization. A more interactive user-friendly qsub that estimates time to allocation would be very useful. Hopefully, our work will lead to more users attempting interactive visualization on Jaguar, resulting in quicker turnaround times for visualization and analysis. As users migrate to using supercomputing platforms for visualization, we expect future research possibilities in this area.

00↗

Filtering adaptive output feedback control for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics

This article synthesizes a filtering adaptive output feedback controller for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics. The multivariable nonlinear systems under consideration have both matched and mismatched uncertainties, which satisfy the semiglobal Lipschitz condition. The unmodeled dynamics are bounded-input bounded-output stable. By adopting an estimation/cancellation strategy, a piecewise constant adaptive law drives the estimation error to zero at every time instant, which yields the adaptive parameters; a disturbance rejection control law is designed to compensate the nonlinear uncertainties within the bandwidth of low-pass filters. The matched uncertainties are cancelled directly by adopting their opposite in the control signal, while a dynamic inversion of the system is required to eliminate the effect of the mismatched uncertainties on the output. A feedforward control law is designed to track a given command. Since the virtual reference system defines the best performance that can be achieved by the closed-loop system, the uniform performance bounds are derived for the states and control signals via comparison. Both numerical and practical examples are provided to illustrate the effectiveness of the proposed filtering adaptive output feedback control architecture, comparisons with the model reference adaptive control demonstrates the superiority of the proposed control method.

filtering adaptive control, mismatched uncertainit↗

Conceptual design and performance predictions for 2D beam emission spectroscopy turbulence measurements at Wendelstein 7-X

A conceptual design for a 2D beam emission spectroscopy diagnostic system to measure ion gyro-scale plasma turbulence at Wendeslstein 7-X is described. The conceptual design identifies field-aligned viewing geometries and ports for cross-field turbulence measurements in the neutral beam volume. A 2D sightline grid covers the outer plasma region, and the grid configuration provides sufficient k-space coverage in radial and poloidal directions for ion temperature gradient and trapped-electron mode turbulence measurements. Emission intensity estimates, optical transmission losses, and detector noise levels indicate that the measurements will be sensitive to plasma density fluctuations as small as δn/n ≈ 0.5% with a bandwidth of 1 MHz. Implementation challenges include a small beam emission Doppler shift due to nearly radial heating beams and reduced optical throughput due to collection aperture limitations.

47 OTHER INSTRUMENTATION↗

Sensitivity limits of an infrared heterodyne spectrometer for astrophysical applications

A discussion and an evaluation of the degradation in sensitivity is given for a heterodyne spectrometer employing a HgCdTe photodiode mixer and tunable diode lasers. The minimum detectable source brightness is considered as a function of the mixer parameters, transmission coefficient of the beam splitter, and local oscillator emission powers. The degradation in the minimum detectable line source brightness which results from the bandwidth being a function of the line width is evaluated and plotted as a function of the wavelength and bandwidth for various temperature to mass ratios. It is shown that the minimum achievable degradation in the sensitivity of a practical astronomical heterodyne spectrometer is approximately 30. Estimates of signal-to-noise ratios with which infrared line emission from astronomical sources of interest may be detected are given.

Abbas, M. M.↗

Sensitivity limits of an infrared heterodyne spectrometer for astrophysical applications

A discussion and an evaluation of the degradation in sensitivity are given for a heterodyne spectrometer employing a HgCdTe photodiode mixer and tunable diode lasers. The minimum detectable source brightness is considered as a function of the mixer parameters, transmission coefficient of the beam splitter, and local oscillator emission powers. The degradation in the minimum detectable line source brightness that results from the bandwidth being a fraction of the line width is evaluated and plotted as a function of the wavelength and bandwidth for various temperature to mass ratios. It is shown that the minimum achievable degradation in the sensitivity of a practical astronomical heterodyne spectrometer is about 30. Estimates of SNRs with which IR line emission from astronomical sources of interest may be detected are given.

Abbas, M. M.↗

An initial assessment of the performance achieved by the Seasat-1 radar altimeter

This paper describes the results of an initial on-orbit engineering assessment of the performance achieved by the radar altimeter system flown on Seasat-1. Additionally, the general design characteristics of this system are discussed and illustrations of altimeter data products are provided. The instrument consists of a 13.5-GHz monostatic radar system that tracks in range only using a 1-m parabolic antenna pointed at the satellite nadir. Two of its unique features are a linear FM transmitter with 320-MHz bandwidth, which yields a 3.125-ns time-delay resolution, and microprocessor-implemented closed-loop range tracking, automatic gain control (AGC), and real-time estimation of significant wave height (SWH). Results presented herein show that the altimeter generally performed in accordance with its original performance requirements of measuring altitude to a precision of less than 10-cm rms, SWH to an accuracy of plus or minus 0.5 m or 10 percent whichever is greater, and ocean backscatter coefficient to an accuracy of plus or minus 1 dB, all over an SWH range of 1 to 20 m.

Townsend, W. F.↗