Search NASA⌕ Search

SEARCH · Search NASA

Results for “bidirectional reflectance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Optical Studies of Low Reflectance Materials at Solar Reflective Wavelengths in Support of Remote Sensing Instrument Development and Calibration

We report the Bidirectional Reflection Distribution Function (BRDF) and Total Hemispheric Reflectance (THR) results of several low reflectance materials using a Table-top Goniometer (TTG) and a commercial UV-VIS-NIR spectrophotometer in support of the NASA GSFC PACE project. The newly developed TTG was utilized to perform the BRDF measurements for several black candidate samples in in-plane and out-of-plane configurations from 300 nm to 2000 nm. These measurements demonstrated the BRDF capability of the TTG to calibrate the dim calibration target with a reflectance of approximately 2 % for the OCI of the PACE project. The spectral THR of the black samples from 200 nm to 2500 nm was determined using a 10 % reflectance diffuse black standard and a monochromator-based light source equipped with a 150 mm diameter integrating sphere. The THR measurement is used to compliment and validate the BRDF measurements acquired from these samples. In this presentation, we also show examples of UV induced BRDF and THR changes on two black coatings. We will discuss validation of the BRDF scale, source stability, measurement repeatability, instrument signature, and uncertainty components.

Bidirectional Reflection Distribution Function (BR↗
NASA NTRS2020

The Effect of UV and Solar Wind Exposure on the Reflectance of Two Black Diffuse Materials

The Bidirectional Reflectance Distribution Function (BRDF) and Total Hemispherical Reflectance (THR) of two candidate black diffuse materials for the dim calibration targets of the NASA GSFC PACE Ocean Color Instrument (OCI)were reported in the SPIE conference last year. In this paper, we present new BRDF and THR results of the two black diffuse materials following additional UV exposure and solar wind tests. The BRDF measurements for five samples of each two black diffuse material were made at incident angles of 0° and 45° and at the wavelengths of 360 nm, 600 nm, and 1600 usi ng the Table-top Goniometer (TTG) located in the Diffuser Calibration Laboratory (DCL) at NASA GSFC. The THR of the samples, 15 mm in diameter, was measured using a commercial UV-VIS-NIR spectrophotometer from 200 nm to 2500 nm. The spectral THR results of the two black diffuse materials exposed to UV and solar wind show an approximate 10 % higher reflectivity than the unexposed samples. The spectral profiles of the THR of the exposed and unexposed samples are relatively similar. The BRDF results at the incident angle of 45° show different trends in the forward and backward scattering regions, while those at normal incident angle are consistent with the THR results. We will also present the details of the samples’ surface features and the comparison of the 0°/45° BRDF and THR results, demonstrate the significance of background subtraction in the THR measurements for small, low reflectance samples, and discuss validation of BRDF scale, measurement repeatability, and major contributions of uncertainty.

Jinan Zeng↗
NASA NTRS2017

Accounting for the Effects of Surface BRDF on Satellite Cloud and Trace-Gas Retrievals: A New Approach Based on Geometry-Dependent Lambertian-Equivalent Reflectivity Applied to OMI Algorithms

Most satellite nadir ultraviolet and visible cloud, aerosol, and trace-gas algorithms make use of climatological surface reflectivity databases. For example, cloud and NO2 retrievals for the Ozone Monitoring Instrument (OMI) use monthly gridded surface reflectivity climatologies that do not depend upon the observation geometry. In reality, reflection of incoming direct and diffuse solar light from land or ocean surfaces is sensitive to the sun-sensor geometry. This dependence is described by the bidirectional reflectance distribution function (BRDF). To account for the BRDF, we propose to use a new concept of geometry-dependent Lambertian equivalent reflectivity (LER). Implementation within the existing OMI cloud and NO2 retrieval infrastructure requires changes only to the input surface reflectivity database. The geometry-dependent LER is calculated using a vector radiative transfer model with high spatial resolution BRDF information from the Moderate Resolution Imaging Spectroradiometer (MODIS) over land and the Cox-Munk slope distribution over ocean with a contribution from water-leaving radiance. We compare the geometry-dependent and climatological LERs for two wavelengths, 354 and 466 nm, that are used in OMI cloud algorithms to derive cloud fractions. A detailed comparison of the cloud fractions and pressures derived with climatological and geometry-dependent LERs is carried out. Geometry-dependent LER and corresponding retrieved cloud products are then used as inputs to our OMI NO2 algorithm. We find that replacing the climatological OMI-based LERs with geometry-dependent LERs can increase NO2 vertical columns by up to 50% in highly polluted areas; the differences include both BRDF effects and biases between the MODIS and OMI-based surface reflectance data sets. Only minor changes to NO2 columns (within 5 %) are found over unpolluted and overcast areas.

Lambert-equivalent reflectivity↗
NASA NTRS1972

Program for determination of radiation interchange factors

Digital computer model was devised for determining thermal and solar radiation interchange factors. Program computes interchange factors among surfaces having any combination of following properties: diffuse emittance and reflectance, diffuse emittance and specular reflectance, diffuse emittance and components of diffuse and specular reflectance, and directional emittance and bidirectional reflectances.

Fesler, L. W.↗
NASA NTRS1987

Abundance and distribution of ultramafic microbreccia in Moses Rock Dike: Quantitative application of AIS data

Moses Rock dike is a Tertiary diatreme containing serpentinized ultramafic microbreccia (SUM). Field evidence indicates the SUM was emplaced first followed by breccias derived from the Permian strata exposed in the walls of the diatreme and finally by complex breccias containing basement and mantle derived rocks. SUM is found primarily dispersed throughout the matrix of the diatreme. Moses Rock dike was examined with Airborne Imaging Spectrometer (AIS) to map the distribution and excess of SUM in the matrix and to better understand the nature of the eruption which formed this explosive volcanic feature. AIS data was calibrated by dividing the suite of AIS data by data from an internal standard area and then multiplying this relative reflectance data by the absolute bidirectional reflectance of a selected sample from the standard area which was measured in the lab. From the calibrated AIS data the minerals serpentine, gypsum, and illite as well as desert varnish and the lithologies SUM and other sandstones were identified. SUM distribution and abundance in the matrix of the diatreme were examined in detail and two distinct styles of SUM dispersion were observed. The two styles are discussed in detail.

Mustard, John F.↗
NASA NTRS2019

Generating Accurate and Consistent Top-Of-Atmosphere Reflectance Products from the New Generation Geostationary Satellite Sensors

GeoNEX is a collaborative project by scientists from NASA, NOAA, JAXA, and other organizations around the world with the purpose of generating a suite of Earth-monitoring products using data streams from the latest geostationary (GEO) sensors including the GOES-16/17 ABI and the Himawari-8/9 AHI. An accurate and consistent top-of-atmosphere (TOA) reflectance product, in particular the bidirectional reflectance factor (BRF), is the starting point in the scientific processing chain. We describe the main considerations and corresponding algorithms in generating the GeoNEX TOA BRF product. First, a special advantage of geostationary data streams is their high temporal resolution (~10 minutes per full-disk scan), providing a key source of information for many downstream products. To fully utilize this high temporal frequency demands a high georegistration accuracy for every acquired image. Our analysis shows that there can be substantial georegistration uncertainties in both GOES and Himawari L1b data which we addressed by implementing a phase-based correction algorithm to remove residual errors. Second, geostationary sensors have distinct illumination-view geometry features in that the solar angle changes for every pixel. Therefore, to accurately derive a BRF requires a solar position algorithm and the estimation of the pixel-wise acquisition time within an uncertainty of 10 seconds. Third, we discuss the measures we adopted to check and correct residual radiometric calibration issues of individual sensors to enable time-series analysis as well as the cross calibration between different satellite sensors (including those from low-Earth orbit). Finally, we also explain the rationale for the choice of the global grid/tile system of the GeoNEX TOA BRF product.

Wang, Weile↗
NASA NTRS1973

Experimental test of plant canopy reflectance models on cotton

Spectroradiometric data on the bidirectional reflectance function was collected for a cotton canopy as a function of observer zenith angle, observer angle, and solar zenith angle. The area under study was about 40 miles from the Gulf of Mexico and the prevailing winds blew inland such that cloud formation increased during the day. The standard reflectance panel was constructed of plywood that had been spray painted with a flat white latex paint. Physical and optical plant parameters were measured. A time lapse mechanism was constructed to operate a 16 mm movie camera such that single frames could be exposed at intervals of one per second up to one per hour. Data were digitized from a strip chart recorder and reflectance panel measurements.

Lemaster, E. W.↗
NASA NTRS1986

Role of scattering distribution functions in spacecraft contamination control practices

A method for spacecraft optical surface contamination monitoring based on the bidirectional reflectance distribution function (BRDF) and the bidirectional transmittance distribution function (BTDF) is described. In the experimental set up, BRDF/BTDF measurements were made at 0.6328 microns using a 35-mW He-Ne laser light source. A correlation of the second order between BRDF and cleanliness levels was observed. It is suggested that bidirectional scattering distribution functions measured on witness mirrors can give information about contamination in clean rooms or vacuum chambers, and that they can be adopted to establish contamination control criteria.

Carosso, P. A.↗
NASA NTRS2001

Infrared Communications for Small Spacecraft: From a Wireless Bus to Cluster Concepts

Nanosatellites operating singly or in clusters are anticipated for future space science missions. To implement this new communications paradigm, we are approaching cluster communications by first developing an infrared (IR) intra-craft wireless bus capability, following initially the MIL-STD-1553B protocol. Benefits of an IR wireless bus are low mass, size, power, and cost, simplicity of implementation, ease of use, minimum EMI, and efficient and reliable data transfer. Our goals are to maximize the reliable link margin in order to afford greater flexibility in receiver placement, which will ease technology insertion. We have developed a concept demonstration using a high-speed visible-band silicon PIN photodiode and a high-efficiency visible LED operating at a data rate up to 4 Mb/sec. In designing an internal IR wireless bus, we have characterized various candidate materials, emitters, and geometries, assuming a single reflection. Thus, we have measured the bidirectional reflectance distribution function (BRDF) for five different materials characteristic of typical spacecraft structures, which range from nearly Lambertian to highly specular. We have fit our data to empirical BRDF functions and modeled the detected irradiance anywhere in the plane of incidence for a divergent (LED) emitter. We have also determined the angular limits on the link geometry to remain within the required bit error rate by determining the received signal-to-noise ratio (SNR) for minimum values of irradiance received at the detector.

Webb, Suzanne C.↗
NASA NTRS2009

MODIS Solar Reflective Calibration Traceability

Long-term climate data records often consist of observations made by multiple sensors. It is, therefore, extremely important to have instrument overlap, to be able to track instrument stability, to quantify, measurement uncertainties, and to establish absolute scale traceable to the International System of Units (SI). The Moderate Resolution Imaging Spectroradiometer (MODIS) is a key instrument for both the Terra and Aqua missions, which were launched in December 1999 and May 2002, respectively. It has 20 reflective solar bands (RSB) with wavelengths from 0.41 to 2.2 micrometers and observes the Earth at three nadir spatial resolutions: 0.25km, 0.5km, and 1km. MODIS RSB on-orbit calibration is reflectance based with reference to the bidirectional reflectance factor (BRF) of its on-board solar diffuser (SD). The SD BRF characterization was made pre-launch by the instrument vendor using reference samples traceable directly to the National Institute of Standards and Technology (NIST). On-orbit SD reflectance degradation is tracked by an on-board solar diffuser monitor (SDSM). This paper provides details of this calibration chain, from prelaunch to on-orbit operation, and associated uncertainty assessments. Using MODIS as an example, this paper also discusses challenges and key design requirements for future missions developed for accurate climate studies.

Xiong, Xiaoxiong↗
NASA NTRS2013

Multitemporal Cross-Calibration of the Terra MODIS and Landsat 7 ETM+ Reflective Solar Bands

In recent years, there has been a significant increase in the use of remotely sensed data to address global issues. With the open data policy, the data from the Moderate Resolution Imaging Spectroradiometer (MODIS) and Enhanced Thematic Mapper Plus (ETM+) sensors have become a critical component of numerous applications. These two sensors have been operational for more than a decade, providing a rich archive of multispectral imagery for analysis of mutitemporal remote sensing data. This paper focuses on evaluating the radiometric calibration agreement between MODIS and ETM+ using the near-simultaneous and cloud-free image pairs over an African pseudo-invariant calibration site, Libya 4. To account for the combined uncertainties in the top-of-atmosphere (TOA) reflectance due to surface and atmospheric bidirectional reflectance distribution function (BRDF), a semiempirical BRDF model was adopted to normalize the TOA reflectance to the same illumination and viewing geometry. In addition, the spectra from the Earth Observing-1 (EO-1) Hyperion were used to compute spectral corrections between the corresponding MODIS and ETM+ spectral bands. As EO-1 Hyperion scenes were not available for all MODIS and ETM+ data pairs, MODerate resolution atmospheric TRANsmission (MODTRAN) 5.0 simulations were also used to adjust for differences due to the presence or lack of absorption features in some of the bands. A MODIS split-window algorithm provides the atmospheric water vapor column abundance during the overpasses for the MODTRAN simulations. Additionally, the column atmospheric water vapor content during the overpass was retrieved using the MODIS precipitable water vapor product. After performing these adjustments, the radiometric cross-calibration of the two sensors was consistent to within 7%. Some drifts in the response of the bands are evident, with MODIS band 3 being the largest of about 6% over 10 years, a change that will be corrected in Collection 6 MODIS processing.

MODIS↗
NASA NTRS2016

Impacts of the Angular Dependence of the Solar Diffuser BRDF Degradation Factor on the SNPP VIIRS Reflective Solar Band On-Orbit Radiometric Calibration

Using an onboard sunlit solar diffuser (SD) as the primary radiance source, the visible infrared imaging radiometer suite (VIIRS) on the Suomi National Polar-orbiting Partnership satellite regularly performs radiometric calibration of its reflective solar bands (RSBs). The SD bidirectional reflectance distribution function (BRDF) value decreases over time. A numerical degradation factor is used to quantify the degradation and is determined by an onboard SD stability monitor (SDSM), which observes the sun and the sunlit SD at almost the same time. We had shown previously that the BRDF degradation factor was angle-dependent. Consequently, due to that the SDSM and the RSB view the SD at very different angles relative to both the solar and the SD surface normal vectors, directly applying the BRDF degradation factor determined by the SDSM to the VIIRS RSB calibration can result in large systematic errors. We develop a phenomenological model to calculate the BRDF degradation factor for the RSB SD view from the degradation factor for the SDSM SD view. Using the yearly undulations observed in the VIIRS detector gains for the M1-M4 bands calculated with the SD BRDF degradation factor for the SDSM SD view and the difference between the VIIRS detector gains calculated from the SD and the lunar observations, we obtain the model parameter values and thus establish the relation between the BRDF degradation factors for the RSB and the SDSM SD view directions.

Lei, Ning↗
NASA NTRS1993

Retrieval of Surface Directional Reflectance and Hemispherical Albedo Using Multi-angle Measurements, I. Ground Level Observations

Knowledge of the directional reflectance properties of natural surfaces such as soils and vegetation canopies is essential for classification studies and canopy model inversions. Atmospheric correction schemes, using various levels of approximation, are described to retrieve surface bidirectional reflectance factors (BRFs) and directional-hemispherical reflectances (albedos) from multi-angle radiance measurements taken at ground level.

factors (BRFs) radiometric calibration sun-view an↗
NASA NTRS2005

Evaluation of MISR Land Surface BRF Measurements: Intercomparison with Coincident Airborne and Ground Field Measurements

The bidirectional reflectance factor, BRF, retrieved by the Multiangle Imaging SpectroRadiometer, MISR, is compared with those coincidently measured from aircraft, by the Cloud Absorption Radiometer, CAR, and MISR airborne simulator, AirMISR, and on the ground, by the Portable Apparatus for Rabid Acquisition of Bidirectional Observations of Land and Atmosphere, PARABOLA Ill. The intercomparisons are made for six types of surfaces: bright desert, salt pans, grassland, forests, snow and the Dismal Swamp. The results show that MISR BRF values are mostly within +/- 10% in agreement with the corresponding airborne and ground measurements, independent of the surface types This study is part of an effort to evaluate and validate MISR surface products.

Multiangle Imaging SpectroRadiometer (MISR)↗
NASA NTRS1991

Surface scattering properties estimated from modeling airborne multiple emission angle reflectance data

Here, researchers apply the Hapke function to airborne bidirectional reflectance data collected over three terrestrial surfaces. The objectives of the study were to test the range of natural surfaces that the Hapke model fits and to evaluate model parameters in terms of known surface properties. The data used are multispectral and multiple emission angle data collected during the Geologic Remote Sensing Field Experiment (GRSFE) over a mud-cracked playa, an artificially roughened playa, and a basalt cobble strewn playa at Lunar Lake Playa in Nevada. Airborne remote sensing data and associated field measurements were acquired at the same time. The airborne data were acquired by the Advanced Solid State Array Spectroradiometer (ASAS) instrument, a 29-spectral band imaging system. ASAS reflectance data for a cobble-strewn surface and an artificially rough playa surface on Lunar Lake Playa can be explained with the Hanke model. The cobble and rough playa sites are distinguishable by a single scattering albedo, which is controlled by material composition; by the roughness parameter, which appears to be controlled by the surface texture and particle size; and the symmetry factor of the single particle phase function, which is controlled by particle size and shape. A smooth playa surface consisting of compacted, fine-grained particles has reflectance variations that are also distinct from either the cobble site or rough playa site. The smooth playa appears to behave more like a Lambertian surface that cannot be modeled with the Hapke function.

Guinness, Edward A.↗
NASA NTRS1992

Influence of atmospheric aerosols and desert reflectance properties on satellite radiance measurements

The influence of surface bidirectional reflectance factors, including shadowing, and of atmospheric aerosol variability are modeled for their effects on the remote sensing of desert targets from space in the 0.7-micron region at high spatial resolution. The white sand reflectance data of Salomonson (1968) are used as the basis for the simulation. The effects of the surface bi-directional reflectance and atmospheric aerosol on the nadir-normalized reflectance measured at the satellite are discussed individually and jointly. The net influence of these two factors is shown to depend on the magnitude of other parameters, such as the surface reflectance and solar zenith angle.

Bowker, D. E.↗
NASA NTRS1990

Reflected Sunlight Reduction and Characterization for a Deep-Space Optical Receiver Antenna (DSORA)

A baffle system for the elimination of first-order specular and diffuse reflection of sunlight from the sunshade of a deep-space optical receiver telescope is presented. This baffle system consists of rings of 0.5cm blades spaced 2.5 cm apart on the walls of GO hexagonal sunshade tubes that combine to form the telescope sunshade. The shadow cast by the blades, walls, and rims of the tubes prevent all first-order reflections of direct sunlight from reaching the primary mirror of the telescope. A reflection model of the sunshade without baffles is also presented for comparison. Since manufacturers of absorbing surfaces do not measure data near grazing incidence, the reflection properties at anticipated angles of incidence must be characterized. A description of reflection from matte surfaces in term of bidirectional reflection distribution function (BRDF) is presented along with a discussion of measuring BRDF near grazing incidence.

Clymer, B. D.↗